1.3. Technical Data
‘Compressor type: ev] Gsv | Gsve | GsviB ] GSvme | SVB
- 50 64 4 411, 447 485
Rotor diameter (mm) 1632 | 1632 | 193 183 233 23
Lengitvaiameter rato 135, 70 135; 180 135, 170
Theoretical displacement per dive] .0028517 | 0035908 | .0047185 | 0062678 | -082077 | 010448
shaft revolution [mrev. (tvrev)]__|_ (00684) | (126788) | (166529) | (222029) | (209009) | (368960)
Normal 50 Hz motor speed {rpm 2950
Displacement al above speed 046 | 6355 | 8046 | 11129 | 14086. ] 1993
[om yh (nmin) 207.0) |_@740) | 4912) | (655.0) | (064.4) "| (1088.5)
‘Special 60 Hz motor speed [pm] 3550_| 9550 | 3550 | 3550 | 3550 | 3550
Displacement at above speed 073 | 7648 | 10043 | 1999.5 | 17073 | 22254
oh (hefin)) 572) |_(499) | 6908) | (669.3) | 1030.6) | (1309.1)
Max. Motor torque atstartup. [Nm] | 2600 | 2600 | 6000 | 6000 | 9000 | ¢000
Max. power continuously at 50 Hz] — 160 160 315 315 500 ‘500
fed,
‘Min imax. motor speed [pm] 7600 (4500
Drive arrangement Direct dive, coupling only.
‘Volume ratio GSB:Vi= 2.8; GSV: Verlable rom22 105.0
‘GSB:9 sleps: 100%, 75% and 50% of fullload
cored eerie GSY: From 100% 10 10% of fuload, infinite adjustment
Rotation of dive shat Gockwise facing the shail end
‘Maximum outlet pressure. pe = 25.0 bar (363 psig)
‘Operating pressure limits
‘Soo section 1.4
Maximum differential pressure
Discharge pressure — suction pressure = max, 240 bar (946 psi)
‘Minimum inlet temperature *
=60°C (-76°F)
‘Maximum inlet temperature
‘93°C (199°F)
Maximum temperature differential
Discharge temperature - suction lemperalure = max, 195°C (2751
‘Maximum outlet temperature 120°C (248°F)
‘Maximum oil supply temp. ** BO°C (176°F)
Minimum oil viscosity ** ‘Kinematic 10 ost
imum oil pressure ™™*
The minimum requirements:
+ cilprossure is moro than the discharge pressure ~1,6 bar, and
+ oil pressure is more than closed thread pressure + S bar.
‘The delay time on cut-out is set to 9 minutes,
Additionally, if there is a solenoid valve in the oil line, the minimum ol
pressure is (closed thread pressure + 1 bar). Delay time 20 sec.
Alternatively you can use a flow switch. Delay time 20 sec. too.
Maximum oll pressure
3.4 bar above discharge pressure
Max. Shaft load, axial and radial
200N
i filration
‘According to 1SO 4572, 825 >75 and B 10>7
‘Solid contamination in oll
‘Acoording to 180 4406 Code 20/16
*
Minimum suction pressure can be lower, but the sensitive temperature to the compressor should meet the
above specification. Minimum inlet pressure Is 0.4 bar for high stage compressors.
It the unit is equipped with stop valve on suction side, the suotion pressure fias to be measured between the
slop valve and the compressor.
*
Recommended oil from sheet 0.00.48-53 has only required viscosity when oll temperature is kept below 65°C,
%4)_ Remember that oll viscosity willbe reduced as refigerant dissolves into the ol.
‘“#) Use level switch or flowmeter to ensure that the oil pressure tansmiller/switch measures oll and not gas.
‘e2-e00-0808-00