Professional Documents
Culture Documents
The finished products may only be sold when the following conditions are applied.
*Full credit must be given to ithinksew.com for the patterns (both online and offline). For example, when products are
sold online, they must include a statement saying “This pattern was designed by ithinksew.com.”
When sold offline, a tag must be attached, stating, “The finished products may only be made by crafters. It may not
be mass produced.” The conditions above may change.
1
Cut out the Fabric
Draw the patterns directly onto the wrong side of a single layer of fabric. Because there is a right and left
shoe you will need to reverse the sole pattern when tracing. Make sure the right and left pieces are
separated to avoid confusion when attaching the soles. Cut out the exterior, lining, and interfacing. Fuse
the interfacing on the wrong side of the lining following the manufacturer’s guide.
Picture 1 Picture 2
Place the upper top piece onto the exterior upper. Place the exterior and lining upper with right sides
Pin in place and topstitch as shown in the picture, together. Pin and sew both pieces, see Picture 2.
see Picture 1. When you make the upper top piece
using the fabric, See Appendix. Stitch the upper top.
Picture 3 Picture 4
Clip the seams and trim the corner seams, see Flip the upper and match the exterior and the lining
Picture 3. with wrong sides together. Press the upper.
Topstitch 1/8” away from the edge. Repeat this
process for other uppers, see Picture 4.
2
Sew the Upper back
Picture 5 Picture 6
Place the exterior upper back pieces with right sides Place the assembled exterior upper back piece and
together. Pin and stitch. Backstitch on both ends, lining upper back piece with right sides together.
see Picture 5. Sew the other exterior upper back and Pin in place and stitch all around the upper back
lining upper back in the same manner. piece, leave the bottom for turning, see Picture 6.
Picture 7 Picture 8
Clip the curved seams, see Picture 7. Press the upper back piece and topstitch 1/8” from
the edge. Topstitch both eyelet line as indicated on
the pattern, backstitch on both ends, see Picture 8.
Picture 9 Picture 10
Attach the 6 eyelet pieces as indicated on the Position the upper back piece onto the upper piece
pattern, see Picture 9. See Appendix. Attach the eyelet. as indicated on the pattern. Pin and stitch together.
Repeat this process for other upper back pieces. Backstitch on both ends.
3
Picture 11
Sew the other side in the same manner. Repeat this
process for other shoe.
Picture 12 Picture 13
To make the 'Red and blue shoe lace version', pin Match their center points. Pin the toe and heel, see
and baste exterior and lining sole with wrong sides Picture 14.
together. Place the lining upper piece and the lining
sole with right sides together.
Picture 14 Picture 15
Then, pin around the rest of the sole. Pin and sew Place the exterior sole piece on the upper with right
both pieces, clipping the heel seams as needed, see sides together.
Picture 16.
4
Opening
Picture 16 Picture 17
Match their center points. Pin the toe and heel. Sew around the sole, leaving a 2 ½” gap for turning.
Then, pin around the rest of the sole, clipping the Make sure all the layers are included and backstitch
heel seam as needed. on both ends.
Picture 18 Picture 19
Trim and clip the seam. Turn the shoe right side out. Sew the opening.
Picture 20
Tie the shoe lace, make the other shoe in the same
manner.
5
Appendix B. Stitch the Upper Top
Picture(Appendix) 1 Picture(Appendix) 2
Place the upper top pieces with right sides Clip the curved seams, see Picture (Appendix) 2.
together. Pin and stitch together, see
Picture(Appendix) 1.
Picture(Appendix) 3 Picture(Appendix) 4
And flip the upper tops and match the exterior and Trim out the lining top piece. Repeat this process
the lining with wrong sides together. Press the for other upper tops.
upper.
Picture(Appendix) 5 Picture(Appendix) 6
Punch the hole through the fabric, using a seam Place the eyelet onto the mount.
ripper first. Then cut the hole using a pair of
scissors.
6
Picture(Appendix) 7 Picture(Appendix) 8
Insert the eyelet into the hole from right side Place the other eyelet on top of the first one.
through to the wrong side.
Picture(Appendix) 9 Picture(Appendix) 10
Place the screw on the eyelet and hit the eyelet
using a hammer. Do this until the eyelet opens up
and clings firmly onto the fabric.
7
KALEY BABY SNEAKERS
Topstitch li e
n e Upper Topstitch lin
Size 1
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam
allowance included
h line
c
KALEY BABY SNEAKERS
Topstit
Sole
Size 1
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam allowance included KALEY BABY SNEAKERS
KALEY BABY SNEAKERS
Upper Top(Fabric) Upper Back
Size 1
Exterior: CUT 4
Size 1
¼” inch seam allowance included Exterior: Cut 4 (2 and 2 reversed)
Lining: Cut 4 (2 and 2 reversed)
Draw the pattern as Interfacing: Cut 4 (2 and 2 reversed)
shown. Then flip it over
so it is the opposite ¼” inch seam
foot and draw it again. allowance included
KALEY BABY SNEAKERS
Upper Top(Leather)
Size 1
Exterior: CUT 2
¼” inch seam allowance included
KALEY BABY SNEAKERS
Topstitch li Upper e
ne Topstitch lin
Size 2
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam
ance included
allowance
h line
c
Topstit
KALEY BABY SNEAKERS
Sole
Size 2
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2 KALEY BABY SNEAKERS
¼” inch seam allowance included KALEY BABY SNEAKERS
Upper Top(Fabric) Upper Back
Size 2 Size 2
Exterior: CUT 4 Exterior: Cut 4 (2 and 2 reversed)
¼” inch seam allowance included Lining: Cut 4 (2 and 2 reversed)
Interfacing: Cut 4 (2 and 2 reversed)
¼” inch seam
Draw the pattern as allowance included
shown. Then flip it over
so it is the opposite
foot and draw it again.
KALEY BABY SNEAKERS
Upper Top(Leather)
Size 2
Exterior: CUT 2
¼” inch seam allowance included
KALEY BABY SNEAKERS
Topstitch li e
ne Upper Topstitch lin
Size 3
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam
allowance
ance included
h line
c
KALEY BABY SNEAKERS
Topstit
Sole
Size 3
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam allowance included
KALEY BABY SNEAKERS
KALEY BABY SNEAKERS
Upper Top(Fabric) Upper Back
Size 3
Size 3
Exterior: CUT 4
Exterior: Cut 4 (2 and 2 reversed)
¼” inch seam allowance included
Lining: Cut 4 (2 and 2 reversed)
Draw the pattern as Interfacing: Cut 4 (2 and 2 reversed)
shown. Then flip it over ¼” inch seam
so it is the opposite allowance included
foot and draw it again.
KALEY BABY SNEAKERS
Upper Top(Leather)
Size 3
Exterior: CUT 2
allow
¼” inch seam allowance included
KALEY BABY SNEAKERS
Topstitch li
ne Upper Topstitch lin
e
Size 4
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam
ance included
allowance
h line
c
Topstit
KALEY BABY SNEAKERS
Sole
Size 4
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2 KALEY BABY SNEAKERS
¼” inch seam allowance included
Upper Top(Fabric) KALEY BABY SNEAKERS
Size 4 Upper Back
Exterior: CUT 4
¼” inch seam allowance included Size 4
Exterior: Cut 4 (2 and 2 reversed)
Lining: Cut 4 (2 and 2 reversed)
Interfacing: Cut 4 (2 and 2 reversed)
¼” inch seam
allowance included
Draw the pattern as
shown. Then flip it over
so it is the opposite
foot and draw it again. KALEY BABY SNEAKERS
Upper Top(Leather)
Size 4
Exterior: CUT 2
¼” inch seam allowance included
KALEY BABY SNEAKERS
Sole
Size 5
Exterior: CUT 2
Lining: CUT 2
h line
Interfacing: CUT 2
¼” inch seam allowance included
c
Topstit
KALEY BABY SNEAKERS
Draw the pattern as
shown. Then flip it over
so it is the opposite
Upper Back
foot and draw it again. Size 5
Exterior: Cut 4 (2 and 2 reversed)
Lining: Cut 4 (2 and 2 reversed)
Interfacing: Cut 4 (2 and 2 reversed)
¼” inch seam
allowance included
KALEY BABY SNEAKERS
Upper Top(Leather)
KALEY BABY SNEAKERS Size 5
Topstitch li e
ne Upper Topstitch lin Exterior: CUT 2
¼” inch seam allowance included
Size 5
Exterior: CUT 2
Lining: CUT 2
Interfacing: CUT 2
¼” inch seam
allowance
ance included
KALEY BABY SNEAKERS
Upper Top(Fabric)
Size 5
Exterior: CUT 4
¼” inch seam allowance included