Professional Documents
Culture Documents
QCVN 7: 2011/BKHCN
HANOI - 2011
Machine Translated by Google
QCVN 7: 2011/BKHCN
Preface
2
Machine Translated by Google
QCVN 7: 2011/BKHCN
1. GENERAL PROVISIONS
1.1. Scope
This regulation prescribes the limits of technical requirements for types of reinforced concrete,
prestressed concrete and epoxy coated concrete reinforcement (hereinafter referred to as concrete
reinforcement) and requirements for quality control for steel for concrete reinforcement produced
This regulation does not apply to steel for concrete reinforcement which is section steel, galvanized steel and
This regulation applies to organizations and individuals manufacturing, importing and distributing
steel for concrete reinforcement, state management agencies and organizations and individuals.
1.3.1. Product batch: Steel for concrete reinforcement of the same grade, same nominal diameter
meaning and produced in the same batch on the same technological line.
1.3.2. Lot of goods: Steel for concrete reinforcement with the same mark, the same nominal
diameter with the same labeling content, imported, distributed and retailed by an organization or individual
grade: The symbol for concrete reinforcement steel is specified in TCVN 1651-1:2008, Reinforced
concrete - Part 1: Plain round bar steel and TCVN 1651-2:2008, Reinforced concrete -
In which: The first "CB" stands for concrete reinforcement. The next three digits represent the
3
Machine Translated by Google
QCVN 7: 2011/BKHCN
finally "T" stands for plain round bar and "V" stands for rebar.
1.3.4. Nominal cross-sectional area of rebar: Cross-sectional area equivalent to the nominal
2. TECHNICAL REQUIREMENTS
2.1.2. Grade and mechanical properties of plain round bar steel according to the provisions of
TCVN 1651-1:2008, Reinforced concrete steel - Part 1: Plain round bar steel (ratio Rm/ReH ÿ 1.46 in
2.1.3. Requirements for ribs, marks and mechanical properties of rebar according to the
2.1.4. Shape, dimensions and mechanical properties of welded wire mesh according to the
Surface shape, size, mass 1 m long and allowable deviation, mechanical properties of
prestressed concrete reinforcement according to the provisions of TCVN 6284:1997 (ISO 6934) :1991),
Part 4 - Sticks;
coating Surface shape, size, volume 1 m long and allowable deviation and
Mechanical properties of epoxy coated concrete reinforcement according to the provisions of:
- TCVN 7934:2009 (ISO 14654:1999), Epoxy coated steel for concrete reinforcement;
stress.
2.4. In the case of imported and domestically produced concrete reinforcement steel according
4
Machine Translated by Google
QCVN 7: 2011/BKHCN
and ASTM standards, the requirements for surface shape, size, mass 1 m long and allowable deviations, marks,
allowable mechanical properties according to the provisions of international standards, regional standards, foreign
d An
kg/m %
2
mm mm
6 28,3 0,222 ÿ8
8 50,3 0,395 ÿ8
10 78,5 0,617 ÿ6
12 113 0,888 ÿ6
14 154 1,21 ÿ5
16 201 1,58 ÿ5
18 255 2,00 ÿ5
20 314 2,47 ÿ5
22 380 2,98 ÿ5
25 491 3,85 ÿ4
28 616 4,83 ÿ4
32 804 6,31 ÿ4
36 1018 7,99 ÿ4
40 1257 9,86 ÿ4
50 1964 15,42 ÿ4
a 2
And = 0.785 4 x d .
b
Mass in length = 7.85 x 10-3 x An.
c
Permissible deviation for a single bar.
1) Diameter d50 applies to rebar only.
2) It is allowed to use the nominal diameter according to international standards, regional standards,
foreign national standards, ASTM standards announced by the manufacturer, which are different from
the diameter stated in Table 1 but not be inconsistent with the relevant provisions of this Regulation.
5
Machine Translated by Google
QCVN 7: 2011/BKHCN
3. TEST METHOD
3.1. Test method for mechanical properties for reinforced concrete and concrete
3.1.1. TCVN 7937-1:2009 (ISO 15630-1:2002), Steel for the reinforcement of concrete and
3.1.2. TCVN 7937-2:2009 (ISO 15630-2:2002), Steel for reinforcement of concrete and
3.1.3. TCVN 7937-3:2009 (ISO 15630-3:2002), Steel for reinforcement of concrete and concrete
Requirements for the isothermal recovery test for 1000 h of domestically produced prestressed
concrete reinforcement in accordance with the applicable standards announced by the manufacturer.
Requirements for 1000 h isothermal recovery test of imported prestressed concrete reinforcement
in accordance with the standards announced by the manufacturer to be applied and must be
demonstrated and committed to have carried out the test. in the import file.
3.2. Test method for mechanical properties of epoxy coated steel as reinforcement
- TCVN 7934:2009 (ISO 14654:1999), Epoxy coated steel for concrete reinforcement;
stress;
- TCVN 7936:2009 (ISO 14656:1999), Epoxy powder and bonding materials for layers
3.3. For steel for concrete reinforcement imported and produced domestically according to
international standards, regional standards, foreign national standards, and ASTM standards, the
requirements for test methods are in accordance with international standards. international standards,
regional standards, foreign national standards, ASTM standards announced by the manufacturer to
apply.
4. WOMEN LABELING
6
Machine Translated by Google
QCVN 7: 2011/BKHCN
4.2.1. Each bundle or coil of steel for concrete reinforcement must be labeled.
4.2.2. Labels of domestically produced steel must include at least the following information: -
Name and address of the manufacturing facility; - Product's name; - Standard numbers announced
- Steel grades;
of manufacture.
4.2.3. The Vietnamese sub-label of imported concrete reinforcement steel must include at least the
following information: - Name and address of the production establishment; - Name of the country of
manufacture; - Name and address of the importing organization or individual; - Product's name; -
- Steel grades;
of manufacture.
be marked during rolling in the following order: - Logo or manufacturer's name or initials; -
CB 240 or CB 2;
CB 300 or CB 3;
CB 400 or CB 4;
CB 500 or CB 5.
- Nominal diameter d.
7
Machine Translated by Google
QCVN 7: 2011/BKHCN
4.4. For imported and domestically produced concrete reinforcement steel according to international
standards, regional standards, foreign national standards, and ASTM standards, the labeling requirements
are in accordance with international standards. , regional standards, foreign national standards, ASTM
5. QUALITY MANAGEMENT
5.1.1. Steel for concrete reinforcement produced in the country must be declared conformity with
regulations in Sections 2 and 4 of this Regulation for each type of steel (according to the grade and nominal
a) The result of certification of conformity of the certification organization is approved by the General Department
b) The test results are in accordance with this Regulation of the testing laboratory designated by the
Directorate for Standards, Metrology and Quality in case the manufacturing facility is applying the quality
management system which has been certified in conformity with the standard. ISO 9001 of the certification
The certification of conformity is carried out according to the method of typical sample testing and
assessment of the production process; supervision through testing of samples taken at the production site or
on the market in combination with assessment of the production process (Mode 5 in Appendix II, Regulations
24/2007/QD-BKHCN dated September 28, 2007 of the Minister of Science and Technology
concrete.
5.1.2. Steel for concrete reinforcement produced in the country when put into circulation on
The market must have the mark of conformity shown on the label of the bundle or roll.
5.2.1. Imported concrete reinforcement steel must be inspected or certified in accordance with the
provisions of Sections 2 and 4 of this Regulation for each type of steel (according to grade and nominal
8
Machine Translated by Google
QCVN 7: 2011/BKHCN
testing samples, assessing the conformity of batches of products and goods (Mode 7 in Appendix II of
24/2007/QD-BKHCN dated September 28, 2007 of the Minister of Science and Technology
Technology).
The inspection or certification of conformity of imported steel reinforcement for concrete reinforcement
5.2.2. Imported concrete reinforcement steel if it has been certified for conformity according to Mode 5
in accordance with the provisions of Sections 2 and 4.4 by a certification body designated or recognized by the
Directorate for Standards, Metrology and Quality. conformity assessment results, the importing enterprise is
5.2.3. Imported steel reinforcement for concrete must be inspected by the state for quality according
to the provisions of Circular No. 17/2009/TT-BKHCN dated June 18, 2009 of the Minister of Science and
Technology guiding the inspection of buildings. quality of imported goods under the management responsibility
The tested steel reinforcement for concrete mentioned above is not required to declare conformity
according to the provisions of Decision No. 24/2007/QD-BKHCN dated September 28, 2007 of the Government.
5.2.4. Steel for concrete reinforcement imported when put into circulation on the market
The field must have the mark of conformity shown on the label of the bundle or roll.
Steel for concrete reinforcement circulated on the market must have the mark of conformity
are shown on the labels and labeling of goods according to the provisions of section 4 of this regulation.
5.3.2. Steel for concrete reinforcement circulating on the market must be inspected by the state for
quality according to the provisions of Circular No. 16/2009/TT-BKHCN dated June 2, 2009 of the Minister of
Science and Technology guiding the State inspection of the quality of goods circulating on the market.
5.4. Regulation conformity certification, regulation conformity announcement, regulation conformity mark and method
Conformity assessment
5.4.1. Regulation conformity certification, regulation conformity announcement, regulation conformity seal and method
9
Machine Translated by Google
QCVN 7: 2011/BKHCN
conformity assessment method specified in Article 5.1; 5.2 and 5.3 comply with the Regulations on certification of
standard conformity, certification of regulation conformity and announcement of standard conformity, announcement
of regulation conformity promulgated together with Decision No. 24/2007/QD-BKHCN dated September 28
5.4.2. The appointment or recognition of a certification organization shall comply with the provisions of
Circular No. 09/2009/TT-BKHCN dated April 8, 2009 of the Ministry of Industry and Trade.
The Minister of Science and Technology guides the requirements, order and procedures for appointing conformity
assessment organizations and Circular No. 11/2011/TT-BKHCN dated June 30, 2011 of the Minister of Science and
Depending on the actual situation, in the case that domestic production and trading of steel for
reinforcement of concrete cannot be assessed for certification of conformity according to method 5, the General
Department of Standards, Metrology and Quality will study and decide on the following: apply the form of inspection
7.
6.1. Domestic production organizations and individuals must make regulation conformity announcement
and labeling in accordance with the requirements specified in Sections 2, 4 and 5 of this Regulation.
When announcing the technical-regulation conformity under Point 5.1.1.b of this Regulation, the
manufacturer must test each type of steel at least once every 6 months and keep the records for at least 10 years.
6.2. Importing organizations and individuals must carry out the inspection or certification of conformity,
register for state inspection and label in accordance with the requirements specified in Sections 2, 4 and 5 of this
Regulation.
6.3. Organizations and individuals that distribute and retail are only allowed to trade in quality steel for
concrete reinforcement, with a seal of conformity and a label in accordance with regulations.
in Section 4 and must have a copy of the declaration of conformity for steel used as reinforcement for concrete products
domestic export according to Point 5.1.1 and a copy of the Notification of import quality inspection results for
10
Machine Translated by Google
QCVN 7: 2011/BKHCN
7. ORGANIZATION OF IMPLEMENTATION
11