Professional Documents
Culture Documents
Preferred Device
SWITCHMODEt
Power Rectifier
DPAK Surface Mount Package
These state−of−the−art devices are designed for use in switching http://onsemi.com
power supplies, inverters and as free wheeling diodes.
Features
ULTRAFAST RECTIFIER
• Ultrafast 35 Nanosecond Recovery Time
6.0 AMPERES
• Low Forward Voltage Drop
200 VOLTS
• Low Leakage
• Pb−Free Packages are Available
Mechanical Characteristics: 1
• Case: Epoxy, Molded 4
3
• Weight: 0.4 Gram (Approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
• Lead and Mounting Surface Temperature for Soldering Purposes: MARKING
DIAGRAM
260°C Max. for 10 Seconds
4
MAXIMUM RATINGS
YWW
Rating Symbol Value Unit DPAK U
1 2
Peak Repetitive Reverse Voltage VRRM 200 V 3 CASE 369C 620TG
Working Peak Reverse Voltage VRWM
DC Blocking Voltage VR
Average Rectified Forward Current IF(AV) A
(Rated VR, TC = 140°C) Per Diode 3.0 Y = Year
Per Device 6.0 WW = Work Week
U620T = Device Code
Peak Repetitive Forward Current IF 6.0 A G = Pb−Free Package
(Rated VR, Square Wave,
20 kHz, TC = 145°C) Per Diode
Non−Repetitive Peak Surge Current IFSM 50 A
(Surge Applied at Rated Load Conditions ORDERING INFORMATION
Halfwave, 60 Hz)
Device Package Shipping †
Operating Junction and Storage TJ, Tstg −65 to +175 °C
Temperature Range MURD620CT DPAK 75 Units/Rail
100 100
70 TJ = 175°C
1.0 100°C
30
20 0.1 25°C
i F , INSTANTANEOUS FORWARD CURRENT (AMPS)
0.01
10
7.0 0.001
0 20 40 60 80 100 120 140 160 180 200
5.0 VR, REVERSE VOLTAGE (VOLTS)
Figure 2. Typical Leakage Current* (Per Leg)
3.0 * The curves shown are typical for the highest voltage device in the
175°C TJ = 25°C voltage grouping. Typical reverse current for lower voltage selections
2.0 can be estimated from these curves if VR is sufficiently below rated
VR.
150°C 100°C
PF(AV), AVERAGE POWER DISSIPATION (WATTS)
14
1.0 13 5.0 SINE
12 10 WAVE
0.7 11
10 IPK/IAV = 20 dc
0.5
9.0
8.0
7.0 SQUARE
0.3
6.0 WAVE
0.2 5.0
4.0
3.0 TJ = 175°C
2.0
0.1
1.0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0
vF, INSTANTANEOUS VOLTAGE (VOLTS) 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10
Figure 1. Typical Forward Voltage (Per Leg) IF(AV), AVERAGE FORWARD CURRENT (AMPS)
Figure 3. Average Power Dissipation (Per Leg)
http://onsemi.com
2
MURD620CT
8.0 4.0
IF(AV) , AVERAGE FORWARD CURRENT (AMPS)
0 0
100 110 120 130 140 150 160 170 180 0 20 40 60 80 100 120 140 160 180 200
TC, CASE TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)
Figure 4. Current Derating, Case (Per Leg) Figure 5. Current Derating, Ambient (Per Leg)
100
70
50
30
C, CAPACITANCE (pF)
20
TJ = 25°C
10
7.0
5.0
3.0
2.0
1.0
0 10 20 30 40 50 60 70 80 90 100
VR, REVERSE VOLTAGE (VOLTS)
Figure 6. Typical Capacitance (Per Leg)
http://onsemi.com
3
MURD620CT
PACKAGE DIMENSIONS
DPAK
CASE 369C
ISSUE O
NOTES:
−T− SEATING
PLANE 1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
B C 2. CONTROLLING DIMENSION: INCH.
V R E INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 0.235 0.245 5.97 6.22
B 0.250 0.265 6.35 6.73
4
C 0.086 0.094 2.19 2.38
Z D 0.027 0.035 0.69 0.88
A
E 0.018 0.023 0.46 0.58
S F 0.037 0.045 0.94 1.14
1 2 3
U G 0.180 BSC 4.58 BSC
K H 0.034 0.040 0.87 1.01
J 0.018 0.023 0.46 0.58
K 0.102 0.114 2.60 2.89
F L 0.090 BSC 2.29 BSC
J
R 0.180 0.215 4.57 5.45
L H S 0.025 0.040 0.63 1.01
U 0.020 −−− 0.51 −−−
D 2 PL V 0.035 0.050 0.89 1.27
Z 0.155 −−− 3.93 −−−
G 0.13 (0.005) M T
SOLDERING FOOTPRINT*
6.20 3.0
0.244 0.118
2.58
0.101
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com MURD620CT/D
4