Professional Documents
Culture Documents
C LO S U R E S F O R O P T I C A L F I B R E S T Y K O F L E X
About Tykoflex Content
The choice of a high quality closure is essential to safeguard a good environment for optical
fibres, especially when installed in harsh and demanding environments. Content
Once installed onto a pole, buried in the ground are supplied as standard product items or Application map 4 Cable bushings 68
or mounted in a manhole or a handhole, the joint adapted to customer configurations, and meet
Cable bushing TKT - cold sealing 68
closure must do the job, decade after decade. the highest requirements for harsh outdoor General information 6 Cable bushing, heat shrink sealing 68
Tykoflex is the manufacturer of T240 closures. conditions, flexibility, technical performance and
The company’s closures have been used since practical handling. How to use this brochure 7 Blind plug SS for sealing of open cable bushing ports. 69
Heat shrink tubes for sealing of cables 69
1977 for copper and since 1985 for fibre. More
than 300,000 units have been installed all over This T240 System overview is designed to Assembly concept 8 Accessories 70
the world. simplify your choice of closure and accessories. Tykoflex Multicassette 10 Accessories Multicassette 70
For all questions and quotations, please contact Cable entry tools 70
Tykoflex AB is a family-owned Swedish us or your Tykoflex T240 distributor. Guide for tools and accessories 12 Cable hanger 70
company, founded in 1958 and based in Tyresö, Special accessories TB/TBK 71
south of Stockholm. The T240 outside plant We are there for you! OPGW 14 T240 closure lid 71
closures are used by telecom and broadband
operators, railway companies, mining and SEAFLEX 24 Mounting 71
Tube cutters 72
offshore industries, power companies and OEM Tykoflex AB
equipment suppliers in many countries. They Single fibre 25 Splice protectors 72
Other accessories 72
Ribbon fibre 53 Pressure test 72
2 3
Application Map for T240 outside plant closures
Railways/tunnels Wind Power lines Wind Offshore
Pole Motorways turbines turbines
T
Direct burial
Data centre
TA Beachflex Seaflex
T T T T
TA Beachflex
Seaflex, for submarine
Sea, lake or river closures, for depths
down to 3000 meters.
Cable length
TS
Seaflex Seaflex
TA Beachflex (pan)
T
Connection point
TS between submarine
cable and ground cable
on shore.
T
TA Branch
TA Joint
Power Line Closures (pan)
TB Line joint for OPGW
TBXL Backbone -High fibre count cables T-OPGW cable. With bran-
ching possibilities.
Special clamps for
TBXL/-S/-R Line joint or dist-
rigid cable.
ribution point for
TSG high fibre count
cables. Line joint for ADSS
Single fibre up T-ADSS cable. With branching
to 576 fibres and possibilities.
ribbon up to Special clamps for
1728 fibres Dome semi rigid cable.
T Operator A
closure (“butt”)
entry.
Backbone Closures (pan)
TST
T Line joint between
cable lengths. One
Distribution Closure - Access Networks branching as option.
TB-5 TBK
Operator B
TB Distribution point. TS Mid-span opening.
Dome closure Two branchings
TB-8 (“butt”) entry. included.
8 x 24 = 192
Microcables TSG Mid-span opening.
Six branchings
Distribution Closure - Heavy duty cables included.
4 5
T Joint Closure T Including single fibre s
The T240 Joint Closure is part of a modular All external parts of the T240 Joint Closure are example we have selected the Joint Closure T (page 30-31).
choose a suitable joint closure for your fibre cables as specified in the table 11 216 105 Cassette holder vertical 11 216 110 Mid-span cable entry tool with
radius protection.
system of lockable closures made of acid proof made of 1.4404 (316L) Acid-Proof stainless steel. below. Brackets for attachment on walls, racks, in manholes or on poles, are
11 218 xxx For splice protectors see page
available as options. Together with a locking cap the closure can easily be
stainless steel. The main benefits of the system Fulfills European standard for outside plant clo- locked with a padlock.
are superior flexibility, easy handling, and tight- sures EN 50411-2-2 (pan closures) as well as EN
ness against overpressure as well as vacuum. 50411-2-4 (dome closures). T240 fulfills the IP 68 T 12, 24, 48 or 72 fibres per MulticassetteOptional accessories and tools Required accessories Option
List of accessories that are recommended or necessary to handle the closure system. For Choice of cable bushing
T
The closures are designed for use in demanding standard (-40° and +70° Celsius)
Joint and
Closure T IP69/IP69K. example, the Tool kit T240 hasIncluded
Exterior dia-
Including
a tool necessary for mounting Accessories
of bushings. single
Additional wrench fibre splice protectors
Choice o
of TKT nipples.10
and is delivered without end plugs or bushings which are selected sepa-
mm.
We recommend
the Tykoflexfor
Tool cable
Interior
Article
kit
11 202 202
T240
use
installation.
fittings Multicassette fibre organizer, 2-p
Instruc Article
11 216 115 Pressure test kit T240
Type of No. of Basic fibres per11cassette.
160 242 T240/150 T 240/24F 240 270/235/150 10 250
rately. The closure is equipped with cable strength member clamps, splice
Including TKT adapter. M6 Din 985 A-4Mid-span cable entry tool with
systems and sewage lines. second digit indicates
height/ lid kg
the degree of protection
No. of Lid 240/50/70/150 Nut Nylock Instruc
protectors and cassettes. Joint Closure T is available in three different sizes, 11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
Part No. fibres splice configu- choose a suitable joint closure for your fibre cables as specified in the table 11 216 105 Cassette holder vertical
depending on the total number of fibres to be spliced and the number of when working
11 216 with
110 closure We recommend that you use
below. Brackets for attachment on walls, racks, in manholes or on poles, are O-ring 239.1x8 EPDM
available as options. Together with a locking cap the closure can easily be
Silica gel 10 g
the harmful entry of various T 12 Fibre forms of moisture locked with a padlock.
T 12, 24,1148
No. Exterior dia-
Required accessories of the selected bracket. Nylock nut and washer are included in Optional acce
Part No. Type of cable bushing Part No. Type of cable bushing
basic configuration.
11 214 005 Wall bracket
0 1 2 3 4 5 6
1 11 160 202 1 11 214 030 1 11 212 132
234 T240/50 96/24F 96 270/140/50 4 100 x x
bushing or end plug Make11a160selection
270/140/50 fromT the 12 cable
Fibre Basic configuration
11 160 231 T240/50 T 24/24F 24 270/140/50 1 25 x 11 160 284 x T240/50 T 288/72F 288
237 T240/70 T 144/24F 144
4 table. For standard
270/160/70
bushing 300 line joints, two ”Cable11
6 150 x
1x24”x
212 018
bushings
x
Cable bushing 6x6x mm 11Interior212 842 11 212
Cable bushing 040 TKT 7x7 mm plastic
Cable bushing 4x1011mm 11 Pole
212bracket
845 for horizontal
Cablebox
bushing TKT 3x7 mm metal 11 214 050
11 160 240 T240/150 T 192/24F 192 270/235/150 8 200 x x 11 160 2xx Bottom part 240 3 hole fittings Instruction T240 Swedish/English 214 030
11 and one
11 160“End plug”, forT 240/24F
future1 branching,
270/235/150would be the 10 choice.
T 12160 201
11 160 286 x T240/50 T240/70
T 12/12FT 432/72F 12 270/140/50 6 12 T 48 Fibre x x Lid 240/50/70/150
242 T240/150 240 250 x x
11 160 232 T240/50 T 48/24F 48 270/140/50 2 50 x Fibre 432 270/160/70 450 11 212 040x x 4x10xsleevemm
Nut Nylock M6 Din 985 A-4 Instruction Multicassette
11 212 cloth050 TKT 3x7 mm metal Cable bushing 1x1011mm 11 212hanger
846 740, one mount
Cable bushing
11 160 261 T240/50 T 48/48F 48 270/140/50 1 50 x
Cable bushing Support 240 11Washer2126.4x18x1.6845 Cable
Emerybushing 214 050 Cable plate TKT 3x7 mm plastic Make your choice from
11 1601 202
11 160 28812x T240/50T240/150
T 24/12F T 576/72F 24 x 576
270/140/50 x T 96/48F 2 96 270/140/508 25 x x O-ring 239.1x8 EPDM Silica gel 10 g
is a wall, pole or manh
10/30 N ”Test finger”11/ 160 234 3 N probe
T240/50 T 96/24F 96 11 160 201
270/140/50 4 T 12/12F 100
T240/50 12 270/140/50 x 270/235/150
11 160 262
Basic
T240/50
configuration
2600 100 x
x 11 212 050
x x
Cable bushing 1x10 mm
V-clampx240
11 212 846
Wellbox 240/50/70/150
11 212
Cable 070 TKT 3x7 mm plastic
bushing Cable bushingMake mmchoice from the list,11depending
3x12your 212 847on whether theStuffing box nipple TKT M12x1
Non protected 50 N sphere Ø 50 mm Ø T2,5 mm 144 1 N steel
11wire Ø 1 mm Dust150protected Dust tight. Same
11 160test
204as 5. T240/50 T 48/12F 48 270/140/50
11 160 264 T240/50 T 192/48F 192
T240/70 T 288/48F 4 288
270/140/50
270/160/70 50
4 200
x
x
x
application
sphere 12,5 mm 11 160 237 T240/70 144/24F 270/160/70
160 202 6 T 24/12F
T240/50 24 270/140/50 x 2 11 160 29025x T240/150 T 720/72F x 720 270/235/150 x 10 725 400 x Ordering examplexof T
11 160 267 6 300 x x
is a wall, pole or manhole.
11 160 270 T240/150 T 384/48F 384 270/235/150 8
x 11 212 070
x x
Cable2x FOC,bushing 3x12 mm 11 212 847 11Stuffing
212 100box nipple TKT M12x1Cable bushing 2x18mm 11 212 870 Cable bushing TKN-K 1,8-4,0
11 160 240 T240/150 T 192/24F 192 270/235/150
11 160 204 8 T 48/12F 200
T240/50 48 270/140/50 x 11 1604 207 50x T240/70 T 72/12F 72 x 270/160/70 1111 160160
272
2xx x Bottom
T240/150 T 480/48F
6 480*= 270/235/150
partPlease
240 3see 75
holenext
10
page
500
x= Please x Interior
x
choice on next page x
make afittings
24 fibre, OD 15 mm Ø and one end plug, mounted on a wooden pole.
Instruction T240 Swedish/English
Ordering example
T 72 Fibre
Choice of Choice of Choice of cable
11 160 242 T240/150 T 240/24F 240 270/235/150 10 T 72/12F 250 x 11 1606 210
11 160 281 T240/50 T 72/72F 72 270/140/50 1 75 x
11 212 x 100
x
Cable bushing x1 2x18mm
Quantity Closure Quantity
11 212Quantity
bracket 870 bushing 11Cable 212bushing
132 TKN-K 1,8-4,0Cable bushing 1x24mm 11 212 871 Cable bushing TKN-K 4,0-7,0
11 160 207 T240/70 72 270/160/70 75x T240/150 T 96/12F 96 x 270/235/150 11 160 282 T240/50 T 144/72F 8 144 270/140/50 100
x Lid 240/50/70/150 2 150 x
Nut
x
Nylock M6 Din 985 A-4 11 214 030 Instruction Multicassette
A typical
1x30 mmexample of an11installation
212 872 case. Cable bushing TKN-K 4x7,0-9,0
11 160 202 1 1 11 212 132
11 160 284 T240/50 T 288/72F 288 270/140/50 4 300 x x
TT240/150
48 FibreT 96/12F 11 1608 212 x 11 212 132 Cable bushing 1x24mm 11 212 871 11Cable
212bushing
145 TKN-K 4,0-7,0Cable bushing
100 T240/150 T 120/12F 120 x 270/235/150 10 240125 x x
11 160 286 T240/70 T 432/72F 432 270/160/70 6 450 x
11 160 210 96 270/235/150 x Support576 sleeve Washer 6.4x18x1.6 Emery cloth
11 160 261 T240/50 T 48/48F 48 270/140/50 1 T 120/12F 50 x
30 11 160 288 T240/150 T 576/72F 270/235/150 8 600 x x
11 212bushing
350 TKN-K 4x7,0-9,0
How to use the table to find the right parts.
Cable bushing divisible 2x18 mm
125x xT 24 Fibre 11 212 145x Cable bushing 1x30 mm 11 212 872 Cable
11 160 290 T240/150 T 720/72F 720 270/235/150 10 725 x
11 160 212 T240/150 120 270/235/150 10 x O-ring 239.1x8 EPDM *= Please see next page x= Please make a choice on next page Silica gel 10 g
11 160 288 T240/150 T 576/72F 576 270/235/150 8 T 192/48F 600 x 11 1604 267 200x T240/70 T 288/48F x 126
288 x 270/160/70 300 x
12 x
Basic configuration
0 1 2 3 4 5 6 7 8 9/K
11 160 264 T240/50 192 270/140/50
11 160 290 T240/150 T 720/72F 720 270/235/150
11 160 267 10 T 288/48F 725
T240/70 288 270/160/70 x 11 1606 270 300x T240/150 T 384/48F 384 x 270/235/150 x 8 400 x x Ordering example of T
*= PleaseTsee next page x= Please make a choice11
on160
next page 10 6 6 of T This list provides an overview of all the parts that are
11 160 270 T240/150 384/48F 384 270/235/150 8 272 400 T240/150 T 480/48F 480 x 270/235/150 x 500 Ordering
x example x 2x FOC, 24 fibre, OD 15 mm Ø and one end plug, mounted on a wooden pole.
always included when ordering the closure.
Protected against Protected against 11 160 272 T240/150 T 480/48F Protected
480 against con-
270/235/150 10 500 x xT 72 Fibre
Protected against Protected against Protected against Protected against High pressure 2x FOC, 24 fibre, OD 15 mm Ø and one end plug, mounted on a wooden pole. Choice of Choice of Choice of cable
Non protected dripping water when low pressure jets of Waterproof tinuous submersion at 11 160 281 T240/50 T 72/72F 72 270/140/50 1 75 x 18 splices x Quantity Closure Quantity bracket Quantity bushing
dripping water.
tilted up to 15°.
spraying water. 30 splashing water.
water.
strong jets of water.
2 bar / 24 h.
proof
T 72 Fibre
Choice of x Choice of 31
Choice of cable
11 160 281 T240/50 T 72/72F 72 270/140/50 11 1601 282 75 T240/50 T 144/72F 144 x 270/140/50 x 2 150 Quantity
x Quantity Quantity
11 1602 284
6 6 x Closure bracket 1 bushing
11 160 202 1 11 214 030 1 11 212 132
11 160 282 T240/50 T 144/72F 144 270/140/50 90 o 150 T240/50 T 288/72F 288 x 270/140/50 x 4 300
12 x
60o 1 11 160 202 1 11 214 030 1 11 212 132
11 1604 286 300 T240/70 T 432/72F 432 x 270/160/70 6 450 x x
min 0,15 m
Min Min
200
3m 113160
m 286 T240/70 T 432/72F 432 270/160/70 11 1606 288 450 T240/150 T 576/72F 576 x 270/235/150 x 8 600 x x
min 1 m
3 min 3 min 0 o
11 160 288 T240/150 T 576/72F 576 270/235/150 11 1608 290 600 T240/150 T 720/72F 720 x 270/235/150 x 11
10 160 231
725 T240/50 T 24/24F
x x
-30 o
Ø 6,3 mm 11 160Ø290
12,5 mm T240/150 T 720/72F 720 270/235/150 10 725 x x *= Please see next page x= Please make a choice on next page
-60next page
*= Please see
o
x= Please make a choice on next page
-90o Closure Lid height Closure type Total number of fibres No. of fibres/Multicassette
30
30 31
6 7
Assembly concept Installation examples
Example with
3 Multicassettes
Features
• 1.4404 (316L) stainless steel closure
• Modular design with few parts
• Splicing in Multicassette fibre organizers ... and closing of strain relief clamp Multicassette in work position
• V-clamp and EPDM rubber O-ring sealing
Benefits
• Rugged shotgun-proof design
• Quick and easy installation Example of
• High fibre count capacity
interior with
strain relief
• Suitable for use in harsh environments clamp
• Lockable with optional locking cap and padlock
Example of
bottom part -
Model T
Example of
cable ports and
Typically all internal parts are delivered assembled.
blind plugs
8 9
Tykoflex T240 Multicassette Tykoflex Multicassette offers great flexibility
Tykoflex Multicassette fibre organizer Multicassette
Multicassette for multipurpose application: Single fibre, C Tubes or ribbon fibre are held in place in the The Multicassette is comprised of a bottom part with The Multicassette is covered with a transparent snap-
4-ribbon, 8-ribbon and 12-ribbon as well as splitters. One fibre inlet guide. Ribbon fibres are guided from the cable two inlet fibre areas with one six slot rubber profile on lid. The transparent lid provides good visibility of
cassette type for all applications. port without any additional protection tube to the cas- in each. The fibres/ fibre tubes are guided in position the installed fibres without having to open the cassette.
sette inlet and held in position. through the rubber profile into the storage area. The cassette’s innovative design makes a re-splice of
A On its way from cable port to cassette, the single fibres The cassette can organize and store all types of fibre fibre an easy task. There can even be different lengths
are always guided in tubes, either from the cable or in D Fibres are safely routed in 45-90 mm radius loops, e.g. single, ribbon etc. There are nine positions for of fibre at each side of the splice sleeve.
the tubes provided by Tykoflex. When adapting to centre loosely and without pressure. Generous space inside storage of fibre sleeves. Each holder slot can store 4 to
tube cables it is recommended to use the branching kit the cassette enables the fibre to be turned and change 8 single fibres sleeves, two 4- or 8-ribbon sleeves or one The Multicassette handles Single Element, Single Rib-
11 218 340 (page 68). direction. There is no need to adjust for precise length of 12-ribbon sleeve. bon, Multiple Element and Multiple Ribbon configura-
fibre before splicing. tions.
B Tubes are secured with cable ties on the cassette inlet. There are also two dedicated areas in the cassette for
additional sleeve holders or splitters. The large cassette
A. Multicassette 11202200 with the open design enables easy, safe and timesaving Multicassette flexibility
B installation. It is possible to change direction and turn Tykoflex Multicassette offers great flexibility. Additional
Fibre inlet guide Fibre inlet guide fibres inside the cassette, within the allowed bending cassettes can be added up to a maximum of 16. The
Holes for strapping
C buffer tubes radius for the fibre. Since fibres are routed in numbered closure lid must then be replaced to handle the extra
slots it is fast to locate the correct fibre for future fault- height of the added cassettes.
finding or splicing.
Fibre Guide
The fibres are placed into the fibre sleeve holder
and are held by rubber elements in the slot. 2
1. Round rubber piece 4. S plice protector slim 2.0 mm 1
2. Square rubber piece 5. Ribbon 4-8 fibre
3. Splice protection sleeve 2.4 mm 6. Ribbon 12 fibre
3 4 5 6
Example shows different configurations of fibre sleeve storage in the sleeve holder.
10 11
Guide for tools and accessories Aerial fibre systems
Blind plug
Multicassette holder
Multicassette
A
Work position
B holder
For TB and
A: Horizontal holder TBK closures
B: Vertical holder
Loose tube storage OPGW ADSS
Placed underneath the Multicassette.
Cable bushing Cold vulc. sealing Tool for cold sealing Cold comp. method
TKT3x7 Adapter
TKN-O
2x 5,5-7,2 TKN-L
4x 7-9
TKT7x7 TKT wrench
With cable diameter
compensator
Branching clip
For mid-span/window
cut cable access.
OPGW is an optical ground wire (OPGW) is a type of cable ADSS is a self supporting fibre cable used for aerial instal-
that is used in the construction of electric power transmis- lations, on pole structures. The optical fibre itself is dielectric
Radius protection tool sion and distribution lines. The cable combines the functions and not affected by power in transmission lines, lightning
For mid-span/window cut. of grounding and fibre communication. induction, external noise or crosstalk.
An OPGW cable has a tubular structure with one or more Typically ADSS cables contain single-mode fibres with low
optical fibres inside, surrounded by layers of steel and transmission loss, allowing long distance transmission at
aluminium wire. The conductive part connected to earth in high speed. Please see page 40-41 for ADSS single fibre.
towers, shields the high-voltage conductors from lightning.
The optical fibre itself is dielectric and not affected by power
Branching kit in transmission lines, lightning induction, external noise or
Centre tube divider crosstalk.
Typically, OPGW cables contain single-mode fibre with low
transmission loss, allowing long distance transmission at high
speed. For OPGW see page 14-23.
12 13
OPGW How to order our OPGW closures
OPGW
On the following pages the comprehensive system
from Tykoflex for OPGW fibre installation is described.
There are brackets for storing overlength of cable and OPGW jointing system
attachment for steel towers, steel poles and wood This is an example of how to use this
poles. It is of the outmost importance that for example brochure for ordering a OPGW closure.
cable clamps are the right size for the cable diameter Depending on the type of cable, you will
to avoid compression that can cause transmission be guided through the options that are
failures. available.
In this example of an OPGW cable with
stainless steel Tube ID 2.9 mm and OD 3.3
Cable specifications mm. The overall diameter is 14.9 mm. The
OPGW
Please OPGW
note that it is of utmost importance toJoint Joint
haveClosure
a Closure OPGW 3H
OPGW 3H OPGW design is 48 F. Cable in and out with
OPGW OPGW
detailed cable specification
JointtoClosure
select the necessary
OPGW Joint
3H Closure OPGW 3H possibility to branch.
parts for a successful installation. Please see page 15 The Joint Closure OPGW 3H (Optical Ground Wire) model has three open Necessary accessories
The Joint Closure OPGW 3H (Optical Ground Wire) model has three open Necessary accessories
for further information.The Joint Closure OPGW 3H (Optical
holes for
The Joint
Ground
holes for customer adaptation. The closure is suitable for use above ground,
customer
Closure adaptation.
Wire) OPGW
model 3H The closure
has(Optical
three open
Groundis suitable for use
Wire) model hasabove
three ground,
open Choice of cable clamp Choice of FIMT
attached
attached to high voltage towers, poles, walls or other support
toishigh voltage towers, poles, walls or other support structures.
Necessary
structures.
The
accessories
The Necessary
Choice accessories
of cable clamp Choice of FIMT
holes for customer adaptation. The holes closure
for customer suitable
closure adaptation.
comes for with
use above The
three ground,
closure
holes forisoptional
suitable for use
end plugs above andground,or cable bushings
Cable clamp plastic, Cable clamp aluminium, Nr. of
attached to high voltage towers,closure withChoice of cable clamp Choice of cable clamp Choice ofNo.FIMT Choice of FIMT
comes or with three holes for optional Theend plugssupport
and or cable bushings Part No. PartCable
attached
poles, walls to high
which other
voltage
are support
selected towers, structures.
poles,
separately. walls
The or other
closure is equipped structures. cable The strength
Part No.
Cable clamp for plastic,
cable diameter Part No. for cable diameter Part No. PartSSNo.
clamp aluminium,
tube ID
SS tube
Nr. ofID fibresType of FIMTType of FIMT
which are selected separately. The closure isend
equipped and withorcable strength
Installation instructions for OPGW
closure comes with three holes for
which are selected separately. The
closure
which
optional
member
closure
comes
is
endwith
member
areclamps,
selected
equipped
determine
plugs three
andholes
clamps,
splice
separately.
thewith
or
number
cable
splice
protectors
cable
forprotectors
Theof
optional
bushings
and
strength
closure cassettes.
cassettes.
and plugs
is equipped
cassettes. The
The number
Please choose with cable
cable
number
of fibres
a suitable
bushings
strength
of fibres will Cable clamp plastic,
will
Part No.
joint closure for cable diameter 11Part No.Part11No. 218 210
for cable diameter
CableCable
for cable
clampclamp plastic,
Cable clamp
fordiameter
cable
aluminium,Part No.
1x25 mm PA Part
11 218
for cable diameter
Cable clamp aluminium, Nr. of
No.269 SS tube ID AL fibres
Cable clamp 25.0 mm Part No. Type 11 218 ofSSFIMT
tube ID 1.93-2.33
700
fibres
Nr. of
Type ofFIMT FIMT Kit S-tube 1.93-2.33 mm
218 210 Cable clamp 1x25 mmdiameter
PA 11 218 269 for cable
Cable clamp diameter
AL 25.0 mm 11 218 700 1.93-2.33 fibres FIMT Kit S-tube 1.93-2.33 mm
There is a generic installation member clamps, instruction for member
splice protectors OPGW
determine
and cassettes. the
clamps,
for yourThe
number
splice
fibre
of
number cassettes.
protectors
cables ofasfibres Please
andwill
specified
choose
cassettes. a suitable
The number
in the table below. Depending
joint closure
of fibres willon the cable 11 218 212 Cable clamp 2x25 mm PA 11 218 702 2.4-2.8 FIMT Kit S-tube 2.4-2.8 mm
for your fibre cables as specified inclosure
the table below.aDepending the11cable
onclosure 218 210 Cable clamp 1x25 mm PA 11 218 210 11 218 269 Cable clamp
212 Cable 1x25
clamp
2x25 mmALPA25.0 mm 11 218 26911 218 700 Cable clamp 1.93-2.33
AL 25.0 mm 11 218 700
FIMT702 Kit S-tube 1.93-2.33
1.93-2.33
2.4-2.8 mm FIMT
FIMTKitKitS-tube
S-tube1.93-2.33
2.4-2.8 mm mm
cables available on our determine website. theAnd number we alsodetermine
of cassettes. supply
Please typeabethat
choose
the numberawill
suitable
of cassettes.
be jointthe
used, Please
closurechoose will needsuitable
to be equipped joint with a choice of
11 218 214 Cable clamp 3x25 mm PA 11 218 704 2.7-3.4 FIMT Kit S-tube 2.4-3.4 mm
for your fibre cables as specified type for
in the that
your tablewillbelow.
fibre cables
accessories,
used, the
Depending
asi.e. closure
specified
bracket, on will
inclamp
the need
thecabletable to be equipped
andbelow.
FIMT. Depending on the11cable
with a choice of
218 212 Cable clamp 2x25 mm PA 11 218 212 214 Cable clamp 2x25
3x25 mm PA 11 218 702 2.4-2.8 11 218 702
FIMT
704 Kit S-tube 2.4-2.8
2.4-2.8
2.7-3.4 mm FIMT Kit S-tube 2.4-2.8
2.4-3.4 mm
written instruction withtype the that closure.
will be used, We thecanclosure also
accessories,
typewillthatsupp-
need willtoi.e.
The bebracket,
be used,
equipped
tables theclamp
on the closure
with and FIMT.
a choice
opposite will need of towill
page behelp
equipped
you towith determine a choice the of necessary 11 218 216 Cable clamp 4x25 mm PA 11 218 706 3.2-3.9 FIMT Kit S-tube 3.2-3.9 mm
OPGW ly customer tailored instruction for a specific OPGWaccessories for the OPGW 3H. The OPGW 3H is always equipped with the
accessories, i.e. bracket, clamp and The
accessories,
FIMT. tables on
i.e. the opposite
bracket, clamp page
and will
FIMT. help you to determine the necessary11 218 214 Cable clamp 3x25 mm PA 11 218 214 216 Cable clamp 3x25 4x25 mm PA 11 218 704 2.7-3.4 11 218FIMT 704Kit S-tube 2.4-3.4
706 2.7-3.4
3.2-3.9mm FIMT Kit S-tube 2.4-3.4
3.2-3.9 mm
accessories for the OPGW 3H. pageThe OPGW 3H youis always equipped with the 11 218 218 Cable clamp Ø 6.0 mm PA 11 218 253 Cable clamp AL 6.0 mm 11 218 708 4.1-5.2 FIMT Kit S-tube 4.1-5.2 mm
The tables on the opposite page The
will tables
help youon to
the determine
opposite the necessary
will help to determine the necessary11 218 216 Cable clamp 4x25 mm PA 11 218 216 Cable clamp 4x25 mm PA 11 218 706 3.2-3.9 11 218 706
FIMT Kit S-tube 3.2-3.9
3.2-3.9 mm FIMT Kit S-tube 3.2-3.9 mm
cable, in which case weaccessories need a for sample of theaccessories
the OPGW 3H. Thearticles
cable.
OPGWspecified
articles specified in the table on the opposite page (basic configuration).
3H foris theincable
always the
OPGW table
equipped 3H.on The the
withOPGWopposite
the ispage (basic configuration).
218
11 218 220
Cable clamp Ø 6.0 mm PA
Cable clamp Ø 8.0 mm PA
11 218 253
11 218 254
Cable clamp AL 6.0 mm
Cable clamp AL 8.0 mm
708 4.1-5.2 4.1-5.2
The type of FIMT kit depends on the design of the OPGW cable. From the datasheet note the fibre
If your specification is not3H coveredalwaysby equipped
the tables, with please the contact
11 218 218 Tykoflex. Cable clamp Ø 6.0 mm PA11 218 220 218
11 218 253 Cable clamp Cable 6.0
clamp 25311 218 708 The type of
11 218FIMT FIMT
708Kit kit depends on the design of the OPGW cable. From the datasheet note3.6/3.2
the fibre
If opposite
yourspecified
cablepage specification is not covered by the tables, please contact Tykoflex. Ø 8.0 mmAL PA6.0 mm 11 218 254 Cable clamp AL 6.0 mm
4.1-5.2
8.0 S-tubesteel
stainless 4.1-5.2
4.1-5.2
tube mmODx.xx/IDx.xx to select the FIMT Kit For
right kit. S-tube
an SS4.1-5.2
tube mm mm the Part No:
articles specified in the table on the articles in(basic
the table configuration).
on the opposite page (basic configuration). 11 218 222 Cable clamp Ø 10.0 mm PA The 11 218 255kit depends Cable clamp AL 10.0OPGW
mmstainless steel tube ODx.xx/IDx.xx
11218704 FIMT KittoS-tube
select2.9-3.4
the rightshall
kit.be
Forused.
an SS tube 3.6/3.2 mm the Part No:
11 218 220 Cable clamp Ø 8.0 mm PA11 218 222 220
11 218 254Cable Cable clamp
clamp Cable 254 type of FIMT on the design of the The cable.
type of
From
FIMT the
kit datasheet
depends onnote
the the
design
fibre of the OPGW cable. From the datasheet note the fibre
If your cable specification is not covered If your by cablethespecification
tables, pleaseis contact not covered Tykoflex.by the tables, please contact Tykoflex. ØØ 10.0
8.0
clamp
mm
mmAL PA
PA8.0 mm 11 218 255 Cableclamp
Cable clampAL AL10.0
8.0 mm mm
stainless steel tube ODx.xx/IDx.xx to select the right kit.
11218704 FIMT Kit S-tube 2.9-3.4 shall be used.
stainless
For ansteel
SS tube
tube 3.6/3.2
ODx.xx/IDx.xx
mm
OPGW 11 218 281 Cableshall
clamp AL 11.4 mm Choice of the to
Part
bracket select
No: the right kit. For an SS tube 3.6/3.2 mm the Part No:
OPGW 3 holes for 24 or 36 fibres per Multicassette 11 218 222 Joint ClosureCable
OPGW 3H Ø 10.0 mm PA11 218 222
clamp 11 218 255Cable clamp Cable
Ø 10.0
clamp mmALPA10.0 mm 11 218 281 11218704
255 FIMT
CableKit S-tube 2.9-3.4
clamp AL 11.410.0 mmbe used. 11218704 Choice of FIMTbracket
Kit S-tube 2.9-3.4 shall be used.
OPGW 3 holes for 24 or 36 fibres per Multicassette 11 218Necessary
224 accessories Cable clamp Ø 12.7 mm PA Choice 11 218 256 Cable clamp AL 12.0 mm
281Choice of FIMT ofCable bracket Choice of bracket Part No. Type of bracket
The Joint Closure OPGW 3H (Optical Ground Wire) model has three open
11 218 224 11 218 281Choice Cable clamp Cable clamp AL 11.4 mm 11 218 256
clamp Ø 12.7 mm PA
holes for customer adaptation. The closure is suitable for use above ground,
clamp AL 12.011.4 mm
OPGW 3 holes for 24 or 36 fibres OPGW per 3Multicassette
holes for 24 or 36 fibres per Multicassette 11 218 226
of cable attached to high voltage towers, poles, walls or other support structures. The
Part
bracket
No. 11 214 106
for cable diameter Part No.
Type of
for cable diameter Part No. SS tube ID fibres Type of FIMT
setteper diameter/ kg Basic 11 214 114 Mounting plate power line Fzb
articles specified in the table on the opposite page (basic configuration).
mm
Stainless steel tube
protec- to bushing or Cable clamp Ø 16.0 mm PA 114 plate
stainless steel tube ODx.xx/IDx.xx to select the right kit. For an SS tube 3.6/3.2 mm the Part No:
Multi-cas- Type Multi-cas-
fibres total height/ Typekg total height/
11218704 FIMT Kit S-tube 2.9-3.4 shall be used.
Part No.
mm
11 160 631 T240/50 OP vGW 3H 24/24F tors 24 ration* 270/140/50
cassettes bracket
on cable Ø Aluminium-clad steel wire
tors1
according to
ration*
25
cable
depending
on cable
bushing or bracket
endØplug x
according to bushing
xcable
11 218
x plug
end
or 232 Included Cable clamp
x
Necessary
OPGW 3
holes
mm PA11 218 232
Ø 16.0accessories 234 Cable clamp Ø 16.0
Exterior
11 218 236
17.1 mm PA
Cable clamp Ø 18.0 mm PA
11 218 261
1111 214218
Cable clamp AL 17.1 mm
116262 Cable clampMountingAL 18.0 mm
11 218 226
11 218 228
11 214
plate power116 line, Fzb
Cable clamp Ø 13.7 mm PA
11 214 120
Cable clamp Ø 14.0 mm PA
Mounting
11 218 257
11 218 258
Mountingplateplatepower
Cable clamp AL 13.7 mm
Mounting plate stainless teel
Cable clamp AL 14.0 mm
line,teel
Fzb
11 214 106 Pole bracket 800 OPGW wood pole
11Part
160No.
24 fibre per
120 stainless
diameter/ Weight 11 214 110 Pole bracket 800 for OPGW steel tower
No. of total
631
Multi-cas-
T240/50 OP vGW 3H 24/24F 24 270/140/50 1 25 x x x x 218 234
11 sette
Type
Cable clamp Ø 17.1 mm PA11 218 234 11
236 218 261
height/
Cable
fibres lid height/ kg
clamp Cable
No. of Ø 17.1
clamp
18.0 mm
No. of
AL PA 17.1
splice mm
Choice of
11
Basic cable
218
clamp, 261
262 Cable
Choice of
Choice
clamp AL
of FIMT, 17.1
18.0
Choice of
mm
cable
11 218 230 Cable clamp Ø 15.0 mm PA 11 218 259 Cable clamp AL 15.0 mm
Brackets for OPGW are selected from this table. The selection depends on whether the pole/tower 11 214 114 Mounting plate power line Fzb
Gel
mm cassettes protec- configu- 11 218 232 Cable clamp Ø 16.0 mm PA
ration* depending bracket according to bushing or
T240/50 OPGW 3H(depending
270/140/50 on cable x 21 type)
11 160 632 48/24F 48 270/140/50 2 50 x x x x Part No.
11 218 238
tors
Cable clamp Ø 19.0 mm PA
on cable Ø
11 214 120
cable end plug
Mounting Brackets
11
plate214
11 218 234for
120OPGW
stainless are
teel
is made selected
of wood from
or this
steel.
Cable clamp Ø 17.1 mm PA table. The
Mounting selection
plate
11 218 261 depends
stainless on
teel whether the pole/tower
Cable clamp AL 17.1 mm
11 214 116 Mounting plate power line, Fzb
11 218 242 Cable clamp Ø 21.3 mm PA 11 218 265 Cable clamp AL 21.3 mm11 218 244 Cable clamp Ø 22.0 mm PA 11 218 266 Cable bushings are selected from
Cable clamp AL 22.0 mm joints two ”Cable bushing 1x24
joints bushings
two ”Cableare selected1x24
from
No. of total
11 242
11 218 265Cable clamp 265
per Multi-
Cable clamp Ø 21.3 mm PA11 218 244 Cable 21.3
clamp mmALPA21.3 mm 11 218 266 21.3 mm
bushing 1x24” for the ground
cassette
Type height/
fibres lid height/ kg
Ø 22.0
No. of Choice of
Basic cable
Cable clamp AL
Choice
22.0
Choice of
11 212 134 Cable bushing 1x24 OPGW bushing
OPGW” and one “End plug” ,for
11 212 132 Cable bushing 1x24mm cable and one “End plug” should
The OD (Overall Diameter) of OPGW cable determines the size ofPart No.clamps to beType of from
cable thisbushing Part No. this table. For aType of cable
line bushing
No. of splice clamp, Choice of of FIMT, cable
protec- configu-
Part No. mm cassettes ration* depending
the cable
bracket according to
selected
bushing or
table. An11OPGW standard this table.
OPGW” andFor
onea standard
“End plug” line 11 212 100
,for is the correct
Cable bushing 2x18mm
be chosen.
tors on cable Ø cable end plug
212 134 Cable bushing 1x24 OPGW future branching,
11 218 244 Cable clamp Ø 22.0 mm PA The11OD218 (Overall
244
11 218Diameter)
cable 266 of
ODOPGW
Cable
withBasic clamp cableØdetermines
Cable
configuration
10.7 should 22.0
beclampmmALPAthe
mounted 22.0size
with mm of the
cable cable
11clamp clamps
218Part266No: 11 to be218selected
Cable
255 10.0from
mm.this
clamp ALtable.
22.0 An
Aluminium OPGW are preferred, joints two ”Cable bushing 1x24
mmclamps joints two ”Cable bushing 1x24
Included Necessary accessories 11and212 135 Cable bushing 1x24 OPGW future branching, is the correct
AFLand one “End plug” ,for end point of
choice. At start and
11 160 661 T240/50 OPGW 3H 36/36F 36 270/140/50 1 40 x x x x
OPGW” oneCable
“End bushing
plug” ,for OPGW”
Included Necessary accessoriesThe OD (Overall Diameter) of OPGW cable determinescable with OD 10.7 butshould
if a sizebeis mounted
missing orwith if thecable clamp Partshould
No: 11be218 255the
10.0
11PA212 mm.
type134Aluminium
is used. Theclamps Cablearecable
preferred,
bushing 1x24 OPGW 134 1x24 OPGWAFL
11 160 6xx Bottom part 240 3 hole Interior fittings Wellbox 240/50
OPGW 3 ho- ground cable fixed, ground can either be fixed
11by212 135 Cable bushing 1x24 OPGW
11 160 662 T240/50 OPGW 3H 72/36F 72 270/140/50 2 75 x x x x
choice. At start and end point
an OPGW of a “Cable bush-
section
OPGW 3 ho- les 36 fibre
Exterior 11 160 664 The
theifOD
size(Overall
of the
T240/50 OPGW 3H 144/36F
but a size cable
Diameter)
is missing144 clamps
if of
theto
OPGWbe selected
270/140/50
itself ororrouted ground cable
cable
in a protection
determines
from
4
shouldthisbetable.
PA hose
the
150 size
fixed,AnofOPGW
diam. the
thetype
PA
25 mm.
cableisclamps
used.
For this
x
The
purpose
to be selected
x
ground
the 1x25 cablefrom
canthis
to 4x25
x table. fixed
either
clampsbeare
An OPGW
x
used.by
Lid 240/50/70
future branching, is the correct future
Cable tie 100x2,5mm
branching, ais“Cable
the correct
Emery cloth
Cable clamps Exterior diameter/ cable with OD 10.7 should be mounted with cable clamp cable 11 208 010
Support sleeve 240
End plug PG21 SSchoice. At section
an OPGW bush- and one “Cable
ing 1x24 OPGW”
Nut Nylock M6 Din 985 A-4 Instruction OPGW
itselfPart
withNo:OD1110.7
in218a should
255 10.0 be mm.
mounted Aluminium
with cable
25clamps
clamparethis
Part
preferred,
No: 11 218
the255
1x2510.0 mm.clampsAluminium clamps are preferred,
11 160 667 T240/70 OPGW 3H 216/36F 216 270/160/70 6 220 x x x x
OPGW 3 ho-
les 36 fibreper Multi-
OPGW 3 ho-
Included
Type No. of diameter/
No. of
total height/
Necessary
Weight Included accessories
No. of
Necessary accessories
Choice of Accessories & tools Choice but if a size is missing
or
Choiceorofif the ground cable should bebutfixed,
routed
if a size
the PAis missing
protection
type is used.
or if the
PA hose
Theground
groundcable
diam. mm. For
*= Please see next page
cableshould
can either
be fixed,
purpose
be fixed
the by
11to 212
4x25 135
x= Please make a choice on next page Cable bushing
are used.
PA type is used. The ground cable can either be fixed by
1x24 OPGW AFL 11 212 010
208 135
choice. At startCableandbushing
O-ring 239.1x8 EPDM
V-clamp 240
end point
End plug1x24
of OPGW
PG21 SS AFL ing 1x24 start and end
Washer 6.4x18x1.6
OPGW” and
bushing
Silica gel 10 g
one point
“Cable
1x24”
of
for the ground
Instruction T240 Swedish/English
Instruction Multicassette
height/lidWeight
per Multi- Exterior Type
cassette Exterior
fibres kg an OPGW 11 212section132a “Cable bush- Cable bushing 1x24mm an OPGW1x24”
section athe
“Cable bush-
les 36 fibre les 36 fibre total height/ No. of Basic of cable
Choice Choice Choice
itself orof
routed incable
a protection PA hose diam. 25 mm. itself
For this
or routed
purposeinthe a protection
1x25 Ordering
to 4x25
PAexample
hose
clamps diam.are25 used.
mm. ForClosure
this purpose the 1x2511 to 208
4x25 clamps
R Recommended
are used. End plug PG21 SS
bushing for
cable ground
and one “End plug” should
The OD (overall diameter) of the cable, determines For Joint Closure No. of splice clamp, Choice of of FIMT,
of OPGW 4HWeightthere isNo.an of extended
cassette diameter/ fibres diameter/ kg Basic configu-
of T240 OPGW 3H Joint 010 11 208
212 010
ing 1x24 OPGW”Cable
132 andEndone plug
“Cable
bushing PG21 SS
1x24mm ing 1x24
cable and OPGW”
one andplug”
“End one “Cable
should
lid height/ Weight
Article Article
perNo. No. of cassettes splice cable clamp,depending Choice of of FIMT, according cable be chosen.
height/ mm
per Multi- Multi- protec- of of bracket bracket Choicetoofor bushing or 111x24”
212 for100the ground Cable bushing 2x18mm
OPGW, 48 fibre, cable OD 14,9 mm, SS tube 3.6/3.2 mounted on a steel lattice tower
bushing bushing 1x24” for the ground
Type Partheight/
total No. Type total No. of configu-
11 202 202
mm
the Tykoflex Tool kit T240 for the 1
be chosen. 11 160 632 1
be chosen.
11 214 110 2 11 218 259 2 11 218 704 2 11 212 134
cassettes protec- cassettes bracket according to dependingbushing or bracket according to bushing or Basic configuration 11 212 100 Cable bushing 2x18mm 11 212 100 Cable bushing 2x18mm
ble can be from 0-0.5 mm bigger than the dimen- Part No. the closure. Part No. 11 160
11 218 346 Splice protectors, pack of 25 OPGW joint closure.
14 18
18 15
19
19
18 18 19 19
OPGW accessories OPGW accessories
60 mm
Fibre protection
sleeve
Insert the fibre bundle into the fibre protection sleeve. Keep Vaseline on fibres, when they Insert the fibre bundle with the fibre protection sleeve, about 10 mm into the protection
stick together it will make the slide on/off sleeve easier. The fibre protection sleeve protects hose (330 mm).
the fibre from tube edge.
11 214 106+110 11 214 110 Pole bracket 800 OPGW for lattice tower. 1 When cutting the steel tube, make sure it is straight. thickness of tube is 0.2 mm and use the table below
Incl mounting plate. Use the tube cutter 11 216 131. Never cut the whole to determine the right sleeve size.
11 214 106 11 214 110
way through. Bend and snap off the tube. Normal
11 214 114 Mounting plate, power line Fzb. 1
FIMT kits
11 214 116 Mounting plate Fzb for OPGW 4H 1
Part No. Type of FIMT Fibre protection sleeve Crimp Hose SS tube thickness 0.2 mm
11 218 700 FIMT Kit S-tub 1.93-2.33 FPS 1.92-2.33 Crimp 6.0-2.0 PEL 2.5x3.8 OD 2.23-2.63 mm
11 214 120 Mounting plate, power line in stainless steel. 1
(same as 11 214 114) 11 218 702 FIMT Kit S-tub 2.4-2.8 mm FPS 2.4-2.8 Crimp 9/3 PEL 3.0x4.0 OD 2.8-3.2 mm
11 214 114+120 11 214 116 11 218 704 FIMT Kit S-tub 2.7-3.4 mm FPS 2.7-3.4 Crimp 9/3 PEL 3.5x5.0 OD 3.1-3.8 mm
11 218 706 FIMT Kit S-tub 3.2-3.9 mm FPS 3.2-3.9 Crimp 9/3 PEL 4.0-x5.6 OD 3.6-4.3 mm
11 216 131 Tube cutter 3-16 mm for steel tubes. 1
11 218 708 FIMT Kit S-tub 4.1-5.2 mm FPS 4.1-5.2 Crimp 9/3 PA 6.0x8.0 OD 4.4-5.6 mm
11 216 131 11 216 133 Spare blades for tube cutter. Pack of 10
16 17
OPGW Joint Closure OPGW 3H
The Joint Closure OPGW 3H (Optical Ground Wire) model has three open Necessary accessories
holes for customer adaptation. The closure is suitable for use above ground,
attached to high voltage towers, poles, walls or other support structures. The Choice of cable clamp Choice of FIMT
closure comes with three holes for optional end plugs and or cable bushings
Cable clamp plastic, Cable clamp aluminium, Nr. of
which are selected separately. The closure is equipped with cable strength Part No. Part No. Part No. SS tube ID Type of FIMT
for cable diameter for cable diameter fibres
member clamps, splice protectors and cassettes. The number of fibres will
determine the number of cassettes. Please choose a suitable joint closure 11 218 210 Cable clamp 1x25 mm PA 11 218 269 Cable clamp AL 25.0 mm 11 218 700 1.93-2.33 FIMT Kit S-tube 1.93-2.33 mm
for your fibre cables as specified in the table below. Depending on the cable 11 218 212 Cable clamp 2x25 mm PA 11 218 702 2.4-2.8 FIMT Kit S-tube 2.4-2.8 mm
type that will be used, the closure will need to be equipped with a choice of
11 218 214 Cable clamp 3x25 mm PA 11 218 704 2.7-3.4 FIMT Kit S-tube 2.4-3.4 mm
accessories, i.e. bracket, clamp and FIMT.
The tables on the opposite page will help you to determine the necessary 11 218 216 Cable clamp 4x25 mm PA 11 218 706 3.2-3.9 FIMT Kit S-tube 3.2-3.9 mm
accessories for the OPGW 3H. The OPGW 3H is always equipped with the
11 218 218 Cable clamp Ø 6.0 mm PA 11 218 253 Cable clamp AL 6.0 mm 11 218 708 4.1-5.2 FIMT Kit S-tube 4.1-5.2 mm
articles specified in the table on the opposite page (basic configuration).
11 218 220 Cable clamp Ø 8.0 mm PA 11 218 254 Cable clamp AL 8.0 mm The type of FIMT kit depends on the design of the OPGW cable. From the datasheet note the fibre
If your cable specification is not covered by the tables, please contact Tykoflex. stainless steel tube ODx.xx/IDx.xx to select the right kit. For an SS tube 3.6/3.2 mm the Part No:
11 218 222 Cable clamp Ø 10.0 mm PA 11 218 255 Cable clamp AL 10.0 mm 11218704 FIMT Kit S-tube 2.9-3.4 shall be used.
11 160 664 T240/50 OPGW 3H 144/36F 144 270/140/50 4 150 x x x x Lid 240/50/70 Cable tie 100x2,5mm Emery cloth
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Instruction OPGW
11 160 667 T240/70 OPGW 3H 216/36F 216 270/160/70 6 220 x x x x
O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
*= Please see next page x= Please make a choice on next page
V-clamp 240 Silica gel 10 g Instruction Multicassette
Accessories & tools R Recommended
Article Article
Ordering example of T240 OPGW 3H Joint Closure
OPGW, 48 fibre, cable OD 14,9 mm, SS tube 3.6/3.2 mounted on a steel lattice tower
11 202 202 Multicassette fibre organizer, 2-p 71 531 040 Tube cutter 3-16mm steel tubes
11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock Choice of Closure Choice of Choice of
Quantity Quantity Choice of bracket Quantity cable clamp Quantity Choice of FIMT Quantity cable bushing
* Delivery content
11 216 100 Cassette holder R 11 216 115 Pressure test kit T240 We recommend that you use
the Tykoflex Tool kit T240 for the 1 11 160 632 1 11 214 110 2 11 218 259 2 11 218 704 2 11 212 134
11 218 346 Splice protectors, pack of 25 OPGW joint closure.
1 11 208 010
18 19
OPGW Joint Closure OPGW 4H
The Joint Closure OPGW 4H model has four open holes for customer adapta- Necessary accessories
tion. The closure is suitable for use above ground, attached to high voltage
towers, poles, walls or other support structures. The closure comes with four Choice of cable clamp Choice of FIMT
holes for optional end plugs and or cable bushings which are selected sepa- Cable clamp plastic, Cable clamp aluminium, Nr. of
rately. The closure is equipped with cable strength member clamps, splice Part No. Part No. Part No. SS tube ID Type of FIMT
for cable diameter for cable diameter fibres
protectors and cassettes. The number of fibres will determine the number
11 218 210 Cable clamp 1x25 mm PA 11 218 214 Cable clamp 3x25 mm PA 11 218 700 1.93-2.33 ≤18 FIMT Kit S-tube 1.93-2.33 mm
of cassettes, please choose a suitable joint closure for your fibre cables as
specified in the table below. Depending on the cable type that will be used, 11 218 212 Cable clamp 2x25 mm PA 11 218 216 Cable clamp 4x25 mm PA 11 218 702 2.4-2,8 ≤36 FIMT Kit S-tube 2.4-2.8 mm
the closure will need to be equipped with a choice of accessories, i.e. bracket, 11 218 253 Cable clamp AL 6.0 mm 11 218 286 Cable clamp AL 6.0 mm ext.** 11 218 704 2,7-3.4 ≤48 FIMT Kit S-tube 2.4-3.4 mm
clamp and FIMT.
The tables on the opposite page will help you to determine the necessary 11 218 254 Cable clamp AL 8.0 mm 11 218 287 Cable clamp AL 8.0 mm ext.** 11 218 706 3.2-3.9 ≤72 FIMT Kit S-tube 3.2-3.9 mm
accessories for the OPGW 4H. The OPGW 4H is always equipped with the 11 218 255 Cable clamp AL 10.0 mm 11 218 288 Cable clamp AL 10 mm ext.** 11 218 708 4.1-5.2 ≤96 FIMT Kit S-tube 4.1-5.2 mm
articles specified in the table on the opposite page (basic configuration).
11 218 281 Cable clamp AL 11.4 mm 11 218 284 Cable clamp AL 11.4 mm ext.** The type of FIMT kit depends on the design of the OPGW cable. From the datasheet note the fibre
If your cable specification is not covered by the tables, please contact Tykoflex. stainless steel tube ODx,xx/IDx,xx to select the right kit. For a SS tube 3.6/3.2 mm the Part No:
11 218 256 Cable clamp AL 12.0 mm 11 218 289 Cable clamp AL 12 mm ext.** 11218704 FIMT Kit S-tube 2.9-3.4 shall be used.
11 218 257 Cable clamp AL 13.7 mm 11 218 290 Cable clamp AL 13.7 mm ext.** Choice of bracket
OPGW 4 holes for 24 or 36 fibres per Multicassette
11 218 258 Cable clamp AL 14.0 mm 11 218 291 Cable clamp AL 14.0 mm ext.**
Part No. Type of bracket
11 218 259 Cable clamp AL 15.0 mm 11 218 292 Cable clamp AL 15.0 mm ext.**
OPGW 4 ho-
les 24 fibre
Exterior Included Necessary accessories
diameter/ Weight 11 218 261 Cable clamp AL 17.1 mm 11 218 293 Cable clamp AL 17.1 mm ext.** 11 214 116 Mounting plate power line, Fzb
per Multi- No. of total
Type height/ No. of Choice of Choice Choice of Brackets for OPGW are selected from this table. The selection depends on whether the pole/tower
cassette fibres lid height/ kg Basic cable 11 218 262 Cable clamp AL 18.0 mm 11 218 294 Cable clamp AL 18.0 mm ext.**
No. of splice configu- clamp, Choice of of FIMT, cable is made of wood or steel.
Part No. mm cassettes protec- ration* depending bracket according to bushing or
tors on cable Ø cable end plug 11 218 264 Cable clamp AL 20.0 mm 11 218 295 Cable clamp AL 20.0 mm ext.** Choice of cable bushing
11 160 691 T240/50 OPGW 4H 24/24F 24 270/140/50 1 25 x x x x 11 218 265 Cable clamp AL 21.3 mm 11 218 296 Cable clamp AL 21.3 mm ext.** Cable bushings are selected from
11 160 692 T240/50 OPGW 4H 48/24F 48 270/140/50 2 50 x x x x Part No. Type of cable bushing this table. For a 2x OPGW line
11 218 266 Cable clamp AL 22.0 mm 11 218 297 Cable clamp AL 22.0 mm ext.** joint two ”Cable bushing 1x24
11 160 694 T240/50 OPGW 4H 96/24F 96 270/140/50 4 100 x x x x 11 212 134 Cable bushing 1x24 OPGW OPGW” and two “End plug” ,for
11 218 269 Cable clamp AL 25.0 mm 11 218 298 Cable clamp AL 25 mm ext.** future branching, is the correct
11 160 697 T240/70 OPGW 4H 144/24F 144 270/160/70 6 150 x x x x The OD (Overall Diameter) of OPGW cable determines the size of the cable clamps to be selected from this table. An OPGW 11 208 010 End plug PG21 SS choice.
cable with OD 10.7 should be mounted with cable clamp Part No: 11 218 255 10.0 mm. Aluminium clamps are preferred,
but if the ground cable is to be fixed, the PA type is used. The ground cable can either be fixed by itself or routed in a protec- 11 212 132 Cable bushing 1x24mm
tion PA hose Diam. 25 mm. For this purpose the 1x25 to 4x25 clamps are used. ** The ext. version of cable clamps 11 218
OPGW 4 ho-
Included Necessary accessories 2xx is used for cables installed in the upper holes in the closure. 11 212 100 Cable bushing 2x18mm
les 36 fibre
Exterior
diameter/
per Multi- No. of total height/ Weight
Type No. of Choice of Choice Choice of
cassette fibres lid height/ kg Basic cable
No. of splice configu- clamp, Choice of of FIMT, cable
Part No. mm cassettes protec- ration* depending bracket according to bushing or Basic configuration
tors on cable Ø cable end plug
11 160 6xx Bottom part 240 4 hole Interior fittings Wellbox 240/50/70
11 160 721 T240/50 OPGW 4H 36/36F 36 270/140/50 1 40 x x x x
Lid 240/50/70 Cable tie 100x2.5mm Emery cloth
11 160 722 T240/50 OPGW 4H 72/36F 72 270/140/50 2 75 x x x x
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Instruction OPGW Mastic
11 160 724 T240/50 OPGW 4H 144/36F 144 270/140/50 4 150 x x x x O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
11 160 727 T240/70 OPGW 4H 216/36F 216 270/160/70 6 220 x x x x V-clamp 240 Silica gel 10 g Instruction Multicassette
*= Please see next page x= Please make a choice on next page
Ordering example of T240 OPGW 4H Joint Closure
Accessories & tools R Recommended 3xOPGW, 48 fibre, cable OD 10.7mm, SS tube 3.6/3.2 mounted on a wooden pole + FOC 00 13.3 mm.
20 21
OPGW Joint Closure OPGW 3H+2P
The Joint Closure OPGW 3H+2P model has three open holes for customer Necessary accessories
adaptation and two pre-sealed ports. The closure is suitable for use above
ground attached to high voltage towers, poles, walls or other support struc- Choice of cable clamp Choice of FIMT
tures. The closure comes with two fixed 16mm pre-sealed ports intended for
Nr. of
ground cables and three holes for optional end plugs/ and or cable bushings Cable clamp plastic, Cable clamp aluminium, Part No. SS tube ID Type of FIMT
Part No. Part No. fibres
which are selected separately. The closure is equipped with cable strength for cable diameter for cable diameter
member clamps, splice protectors and cassettes. The number of fibres will 11 218 700 1.93-2.33 ≤18 FIMT Kit S-tube 1.93-2.33 mm
determine the number of cassettes to be used. Please choose a suitable joint 11 218 210 Cable clamp 1x25 mm PA 11 218 242 Cable clamp Ø 21.3 mm PA 11 218 702 2.4-2,8 ≤36 FIMT Kit S-tube 2.4-2.8 mm
closure for your fibre cables as specified in the table below. Depending on 11 218 212 Cable clamp 2x25 mm PA 11 218 244 Cable clamp Ø 22.0 mm PA 11 218 704 2,7-3.4 ≤48 FIMT Kit S-tube 2.4-3.4 mm
the cable type that will be used, the closure will need to be equipped with a
choice of accessories, i.e. bracket, clamp and FIMT. 11 218 214 Cable clamp 3x25 mm PA 11 218 269 Cable clamp AL 25.0 mm 11 218 706 3.2-3.9 ≤72 FIMT Kit S-tube 3.2-3.9 mm
The tables on the opposite page will help you to determine the necessary 11 218 216 Cable clamp 4x25 mm PA 11 218 253 Cable clamp AL 6.0 mm 11 218 708 4.1-5.2 ≤96 FIMT Kit S-tube 4.1-5.2 mm
accessories for the OPGW 3H+2P. The OPGW 3H+2P is always equipped with
11 218 218 Cable clamp Ø 6.0 mm PA 11 218 254 Cable clamp AL 8.0 mm The type of FIMT kit depends on the design of the OPGW cable. From the datasheet note the fibre
the articles specified in the table on the opposite page (basic configuration). stainless steel tube ODx,xx/IDx,xx to select the right kit. For an SS tube 3.6/3.2 mm the Part No:
If your cable specification is not covered by the tables, please contact Tykoflex. 11 218 220 Cable clamp Ø 8.0 mm PA 11 218 255 Cable clamp AL 10.0 mm 11218704 FIMT Kit S-tube 2.9-3.4 shall be used.
11 218 222 Cable clamp Ø 10.0 mm PA 11 218 281 Cable clamp AL 10.0 mm Choice of bracket
11 218 224 Cable clamp Ø 12.7 mm PA 11 218 256 Cable clamp AL 11.4 mm
OPGW 3 holes + 2P for 24 or 36 fibres per Multicassette Part No. Type of bracket
11 218 226 Cable clamp Ø 13.7 mm PA 11 218 257 Cable clamp AL 13.7 mm
OPGW 3
Included Necessary accessories 11 218 228 Cable clamp Ø 14.0 mm PA 11 218 258 Cable clamp AL 14.0 mm 11 214 106 Pole bracket 800 OPGW wood pole
holes Exterior
+2 pipes diameter/ 11 214 110 Pole bracket 800 for OPGW steel tower
No. of total height/ Weight 11 218 230 Cable clamp Ø 15.0mm PA 11 218 259 Cable clamp AL 15.0 mm
24 fibre per Type No. of Choice of Choice Choice of
Multi-
fibres lid height/ kg Basic cable
No. of splice configu- clamp, Choice of of FIMT, cable 11 218 232 Cable clamp Ø 16.0 mm PA 11218261 Cable clamp AL 17.1 mm 11 214 114 Mounting plate power line Fzb
cassette mm cassettes protec- ration* depending bracket according to bushing or
Part No. tors on cable Ø cable end plug 11 218 234 Cable clamp Ø 17.1 mm PA 11218262 Cable clamp AL 18.0 mm 11 214 116 Mounting plate power line, Fzb
11 160 751 T240/50 OPGW 3H+2P 24/24F 24 270/140/50 1 25 x x x x 11 214 120 Mounting plate stainless teel
11 218 236 Cable clamp Ø 18.0 mm PA 11 218 264 Cable clamp AL 20.0 mm
11 160 752 T240/50 OPGW 3H+2P 48/24F 48 270/140/50 2 50 x x x x Brackets for OPGW are selected from this table. The selection depends on whether the pole/tower
11 218 238 Cable clamp Ø 19.0 mm PA 11 218 265 Cable clamp AL 21.3 mm is made of wood or steel.
11 160 754 T240/50 OPGW 3H+2P 96/24F 96 270/140/50 4 100 x x x x
11 218 240 Cable clamp Ø 20.0 mm PA 11 218 266 Cable clamp AL 22.0 mm Choice of cable bushing
11 160 757 T240/70 OPGW 3H+2P 144/24F 144 270/160/70 6 150 x x x x
The OD (Overall Diameter) of OPGW cable. The OD (Overall Diameter) of OPGW cable determines the size of the cable clamps
Cable bushings are selected
to be selected from this table. An OPGW cable with OD 10.7 should be mounted with cable clamp Part No: 11 218 255 10.0 Part No. Type of cable bushing from this table. For a standard
mm. Aluminium clamps are preferred, but if a size is missing or if the ground cable should be fixed, the PA type is used. The
OPGW 3 line joints two ”Cable bushing
holes+2
Included Necessary accessories ground cable can either be fixed by itself or routed in a protection PA hose Diam. 25 mm, for that purpose the 1x25 to 4x25
clamps are used. 11 212 134 Cable bushing 1x24 OPGW 1x24 OPGW” and one “End
pipes
Exterior plug” should be chosen, for
diameter/ 11 208 010 End plug PG21 SS future branching, is the correct
36 fibre per No. of total height/ Weight
Type No. of Choice of Choice choice. For the two fixed 16
Multi- fibres lid height/ kg Basic Choice of ca-
cassette No. of splice configu- cable clamp, Choice of of FIMT, 11 212 132 Cable bushing 1x24mm mm presealed ports the heat
according to ble
mm bushing
cassettes protec- ration* depending bracket shrink 11 219 159 is needed for
or end plug 11 212 100 Cable bushing 2x18mm
Part No. tors on cable Ø cable installation.
Article Article
Ordering example of T240 OPGW 3H+2P Joint Closure
11 202 202 Multicassette fibre organizer, 2-p 71 531 040 Tube cutter 3-16mm steel tubes 3xOPGW, 24 fibre, cable OD 10.7mm, SS tube 3.6/3.2 mounted on a steel tower + 2x FOC, 12 fibre, OD 12 mm in 25 mm PA Hose.
11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
Choice of Closure Choice of Choice of
We recommend that you use Quantity Quantity Choice of bracket Quantity cable clamp Quantity Choice of FIMT Quantity cable bushing
11 216 100 Cassette holder R 11 216 115 Pressure test kit T240 * Delivery content
the Tykoflex Tool kit T240 for the
11 218 346 Splice protectors, pack of 25 OPGW joint closure. 1 11 160 754 1 11 214 114 1 11 218 210 3 11 218 704 3 11 212 134
2 11 219 159
22 23
Seaflex Single fibre
4.
Features
Seaflex is a universal joint closure designed for optical
submarine cables. It is made of highly corrosion resis- EIA598-A Fibre Color Chart
tant material and applicable on most cable designs.
The closure can be used for splicing cables of different 1. Blue 2. Orange 3. Green 4. Brown 5. Slate 6. White 7. Red 8. Black 9. Yellow 10. Violet 11. Pink 12. Aqua
manufacture and designs. The closure is designed for an
easy and quick assembly with ordinary standard tools,
with no welding required at the assembly procedure. 1. Blue 2. Orange 3. Green 4. Brown 5. Slate 6. White 7. Red 8. Black 9. Yellow 10. Violet 11. Pink 12. Aqua
Easy to re-enter.
The closure consists of a main closure kit with the clo- In slotted core cable, the first fibre bundle is located
sure housing and rubber cable bend protections, and 1 between the mark no.1 and No.2 on the core. The third
cable specific connection kits for each unique cable Mark 1 Mark 2 fibre bundle is before mark no.3.
type. The splicing area is designed for accommodation
of up to 192 fibres. Optical fibres are inherently very strong, but their
6 2
The fibre jointing is carried out with an ordinary fu- strength is drastically reduced by unavoidable micros-
sion splicing machine and using standard splice protec- copic surface flaws in the manufacturing process. The-
tion sleeves. The interior of the closure is filled with oil refore, the stress imposed on the fibre during handling,
in order to protect the fibres. For submarine cable ends, cabling and installation must be considered in relation
see beach to a given set of environmental conditions. The surface
closures on 5 3 flaws must also be protected from water, especially
page 50-51. in the closure where the cable is stripped and fibre is
exposed for the splicing process.
Mark 3
Please con- 4 Single fibre cables can be designed as mono tube,
tact Tykoflex multi-tube, slotted core, micro cable, ADSS, OPGW etc.
for further
information.
24 25
T SLIM Joint Closure T SLIM Including single fibre splice protectors
Line joint Accessories & tools R Recommended
Joint Closure T SLIM is primarily intended for line joints with the possibility
of up to two branches. The slim design makes its perfect for use in hand- Article Article
holes. Joint Closure T SLIM is delivered with two open cable inlets and two
11 202 202 Multicassette fibre organizer, 2-p 11 218 056 Locking cap for padlock
sealed cable inlets. All inlets can handle cable diameters from 8 to 22 mm.
Two heat shrinks are included. The closure is equipped with cable strength 11 216 020 Tool kit T240 R 11 218 056 Pressure test kit T240
We recommend that you use
member clamps, splice protectors and cassettes. For branching, the inlet is 11 216 100 Cassette holder R 11 218 xxx For splice protectors see page the Tykoflex Tool kit T240
opened and the cable installed and sealed with heat shrink. when working with closure
T SLIM is available in three different sizes, depending on the total number and accessories.
of fibres to be spliced and the number of fibres per cassette. The number of
Optional accessories
cassettes included depends on the number of fibres required. Brackets for
attachment on walls, racks, in manholes or on poles, are available as options Heat shrink (for additional branching) Choice of bracket
and ordered separately. Together with a locking cap, the closure can easily
be locked with a padlock. Please see table below. Part No. Type of heat shrink Part No. Type of bracket
11 219 159 Heat shrink 34/8 L=200 mm 11 214 005 Wall bracket
T SLIM for 12, 24 or 48 fibres per Multicassette 11 214 030 Pole bracket for horizontal box
26 27
TS SLIM Joint Closure TS SLIM Including single fibre splice protectors
Mid-span
Joint Closure TS SLIM facilitates mid-span access without the need to cut
and re-splice all the fibres in the cable and with the possibility of up to two
branches. The slim design makes it perfect for use in hand-holes. Joint Clo-
sure TS SLIM is delivered with one open oval cable inlet and two sealed cable
inlets. All inlets can handle cable diameters from 8 to 22 mm. Heat-shrink
and clip for the oval inlet are included. Brackets for attachment on walls,
racks, in manholes or on poles, are available as options and ordered sepa-
rately. The closure is equipped with cable strength member clamps, splice
protectors and cassettes. For branching, the inlet is opened and the cable
installed and sealed with heat shrink.
TS SLIM is available in three different sizes, depending on the total number
of fibres to be spliced and the number of fibres per cassette. The number of
cassettes included depends on the number of fibres required. Together with
a locking cap, the closure can easily be locked with a padlock.
Please see table below.
28 29
T Joint Closure T Including single fibre splice protectors
Line joint Accessories & tools R Recommended
Joint Closure T is foremost intended for line joints with the possibility of
branching. Joint Closure T has three open holes for customer adaptation Article Article
and is delivered without end plugs or bushings which are selected sepa-
11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
rately. The closure is equipped with cable strength member clamps, splice
protectors and cassettes. Joint Closure T is available in three different sizes, 11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
We recommend that you use
depending on the total number of fibres to be spliced and the number of TKT spanner for opening and closing of TKT nipples.10 mm.
11 216 100 Cassette holder horizontal R 11 216 073 the Tykoflex Tool kit T240
fibres per cassette. Including TKT adapter. when working with closure
The number of fibres will determine the number of cassettes, please and accessories.
Mid-span cable entry tool with
choose a suitable joint closure for your fibre cables as specified in the table 11 216 105 Cassette holder vertical 11 216 110 radius protection.
below. Brackets for attachment on walls, racks, in manholes or on poles, are
11 218 xxx For splice protectors see page
available as options. Together with a locking cap the closure can easily be
locked with a padlock.
30 31
TS Joint Closure TS Including single fibre splice protectors
32 33
TMC Joint Closure TMC Including single fibre splice protectors
11 162 494 T240/150 TMC 720/72F 720 270/235/150 10 725 x x 1 11 408 247 1 11 212 870
*= Please see next page x= Please make a choice on next page 1 11 208 010
34 35
TSG Joint Closure TSG Including single fibre splice protectors
Mid-span branching Accessories & tools R Recommended
Joint Closure TSG facilitates mid-span access without the need to cut and
re-splice all the fibres in the cable. The closure is delivered with one oval Article Article
cable inlet and two pre-sealed ports, ID 25 mm and four pre-sealed ports, ID
11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
16 mm. The closure is equipped with cable strength member clamps, splice
protectors and cassettes. Joint Closure TSG is available in three different 11 216 020 Tool kit T240 11 218 056 Locking cap for padlock
sizes, depending on the total number of fibres to be spliced and the number TKT spanner for opening and closing of TKT nipples.10 mm.
of fibres per cassette. 11 216 100 Cassette holder horizontal R 11 216 073 Including TKT adapter.
The number of fibres will determine the number of cassettes. Please
Mid-span cable entry tool with
choose a suitable joint closure for your fibre cables as specified in the table 11 216 105 Cassette holder vertical 11 216 110 radius protection.
below. Brackets for attachment on walls, racks, in manholes or on poles, are
11 218 xxx For splice protectors see page
available as options and ordered separately. Together with a locking cap,
the closure can easily be locked with a padlock. The closure TSG is delivered
with heat shrink tube + branch-off clip for the oval inlet and with the articles Optional accessories
specified in the table on the opposite page (basic configuration).
Choice of heat shrink tube Choice of bracket Choice of cable bushing
TSG 12, 24, 48 or 72 fibres per Multicassette
Part No. Type of heat shrink Part No. Type of bracket Part No. Type of cable bushing
Included Optional accessories
11 212 845 Cable bushing TKT 3x7 mm metal
No. Exterior
TSG
dia- 11 219 159 Heat shrink tube 34/8, L = 200 mm 11 214 005 Wall bracket
Type of meter/ total Weight No. of Basic Choice of
height/ lid kg No. of Choice of Choice of 11 219 035 Heat shrink end cap 50/25 for oval inlet. 11 214 030 Pole bracket for horizontal box 11 212 846 Cable bushing TKT 3x7 mm plastic
Part No. fibres height/ splice configu- heat shrink
mm cassettes protectors bracket cable bushing
ration* tube 11 214 050 Cable hanger 740, one mount plate 11 212 850 Cable bushing TKT 1x11 mm metal
TSG 24 Fibre The bracket for T240 is found in the table “Bracket”. Make your Make a selection from the cable bushing table. Cable bushing TKT fits
selection from the list depending on the application on the four 18 mm inlets above the oval inlet.
11 160 531 T240/50 TSG 24/24F 24 270/140/50 1 25 x x x – wooden pole, steel pole/tower.
11 160 532 T240/50 TSG 48/24F 48 270/140/50 2 50 x x x Cold method – Insert oval
11 160 534 T240/50 TSG 96/24F 96 270/140/50 4 100 x x x
11 160 537 T240/70 TSG 144/24F 144 270/160/70 6 150 x x x Part No. Type of cable bushing Part No. Type of cable bushing
11 160 540 T240/150 TSG 192/24F 192 270/235/150 8 200 x x x 11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
11 160 542 T240/150 TSG 240/24F 240 270/235/150 10 250 x x x
11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
TSG 48 Fibre
11 212 853 Insert oval TKN-O 4x 6,5-8,5 11 212 891 Insert oval TKN-IO 14-17
11 160 571 T240/50 TSG 48/48F 48 270/140/50 1 50 x x x
11 160 572 T240/50 TSG 96/48F 96 270/140/50 2 100 x x x
11 160 574 T240/50 TSG 192/48F 192 270/140/50 4 200 x x x Ordering example of TSG
11 160 577 T240/70 TSG 288/48F 288 270/160/70 6 300 x x x FOC, 240 fibre, mid span, 1x OD 17 mm and micro-cable 2X OD 5 mm, wall mounted mid-span.
11 160 580 T240/150 TSG 384/48F 384 270/235/150 8 400 x x x
Choice of Choice of heat Choice of Choice of cable
11 160 582 T240/150 TSG 480/48F 480 270/235/150 10 500 x x x Quantity Quantity Quantity Quantity
Closure shrink bracket bushing
TGS 72 Fibre
11 160 584 T240/50 TSG 72/72F 72 270/140/50 1 75 x x x 1 11 160 542 1 11 219 159 1 11 214 005 1 11 212 845
11 160 586 T240/50 TSG 144/72F 144 270/140/50 2 150 x x x
11 160 588 T240/50 TSG 288/72F 288 270/140/50 4 300 x x x
11 160 590 T240/70 TSG 432/72F 432 270/160/70 6 450 x x x
11 160 592 T240/150 TSG 576/72F 576 270/235/150 8 600 x x x
11 160 594 T240/150 TSG 720/72F 720 270/235/150 10 725 x x x
*= Please see next page x= Please make a choice on next page
Basic configuration
11 160 5xx Bottom part 240 TSG Interior fittings Heat shrink 50/16. L =200 mm.
Lid 240/50/70/150 Cable tie 100x2.5mm Branch -off clip
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Wellbox 240/50/70/150
O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
V-clamp 240 Silica gel 10 g Instruction Multicassette and Emery cloth
36 37
TST Joint Closure TST Including single fibre splice protectors
Termination Necessary accessories
Joint Closure TST is primarily intended for termination and cross coupling
of fibre in an outdoor environment. In addition measurements of fibre can Choice of cable bushing Choice of pigtail
easily take place. A fibre adaptor panel and fibre organizer cassettes are
included. The closure is delivered with one oval cable inlet and has two open Part No. Type of cable bushing Part No. Type of cable bushing Part No. Type of pigtail
holes for customer adaptation and is delivered without end plugs or bushi-
ngs which are selected separately. 11 208 010 End plug PG21 SS 11 212 145 Cable bushing 1x30 mm 11 349 702 Pigtail SM SC/VPC 0.9 L = 1000 mm
The closure is equipped with a fibre adaptor panel, cable strength member 11 212 018 Cable bushing 6x6 mm 11 212 350 Cable bushing divisible 2x18 mm 11 349 801 Pigtail SC/UPC 12R-SM-0.9-3 high quality
clamps, splice protectors and a cassette. Joint Closure TST is available in four
11 212 040 Cable bushing 4x10 mm 11 212 840 Cable bushing TKT 7x7 mm metal
different sizes, depending on the total number of fibres to be connected, (12
11 212 050 Cable bushing 1x10 mm 11 212 842 Cable bushing TKT 7x7 mm plastic Choice of adaptors
to 96 SC), please choose a suitable joint closure for your application as speci-
fied in the table below. Brackets for attachment on walls, racks, in manholes 11 212 070 Cable bushing 3x12 mm 11 212 860 Cable bushing TKN-L 1,8-4,0 Part No. Type of adaptor
or on poles, are available as options and ordered separately. Together with a
11 212 100 Cable bushing 2x18mm 11 212 861 Cable bushing TKN-L 4,0-7,0
locking cap, the closure can easily be locked with a padlock. 11 348 810 Adaptor SC Simplex Zr
The closure TST is delivered with heat shrink tube + branch-off clip for the 11 212 132 Cable bushing 1x24mm 11 212 862 Cable bushing TKN-L 4x7,0-9,0
11 348 812 Adaptor SC Duplex Zr
oval inlet and with the articles specified in the table on the opposite page Cold method – Insert oval
(basic configuration). 11 348 840 Adaptor SC/APC Simplex Zr
11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
11 348 842 Adaptor SC/APC Duplex Zr
11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
TST 24 fibres per Multicassette 11 212 853 Insert oval TKN-O 4x 6,5-8,5
Make a selection from the cable bushing table.
Accessories
Included
Necessary Optional
TST
No. of Exterior Optional accessories
fibres diameter/ total Weight
24 Fibre Type Choice of
Part No. termi- height/ lid kg No. of Basic Choice of bracket
nated height/ mm Patch panel cable
No. of splice confi- Choice of bushing Choice of Choice of
with holes
cassettes protec- gura- pigtail adaptors bracket
for or end Part No. Type of bracket
tors tion* plug
11 214 005 Wall bracket
11 160 451 T240/50 TST 12/F 12 270/140/50 3.8 1 25 12xSC Simplex x x x x
11 160 453 T240/70 TST 24/F 24 270/140/70 3.9 2 50 12xSC Duplex x x x x 11 214 030 Pole bracket for horizontal box
11 160 455 T240/150 TST 48/F 48 270/140/150 4.4 4 100 24xSC Duplex x x x x 11 214 050 Cable hanger 740, one mount plate
11 160 457 T240/200 TST 96/F 96 270/140/200 5.6 4 200 48xSC Duplex x x x x The bracket for T240 is found in the table “Bracket”. Make your
selection from the list depending on the application
*= Please see next page x= Please make a choice on next page – wooden pole, steel pole/tower.
1 11 160 455 1 11 214 005 96 11 349 702 24 11 348 812 2 11 208 010
38 39
ADSS Joint Closure ADSS Including single fibre splice protectors
ADSS (All-Dielectric Self-Supporting) Accessories & tools R Recommended
The Joint Closure ADSS can be mounted on any pole or tower with a suita-
ble bracket. Joint Closure ADSS has three open holes for customer adapta- Article Article
tion and is delivered without end plugs or bushings which are selected 11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
separately.
The closure is equipped with cable strength member clamps, splice pro- 11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
tectors and Multicassette. Joint Closure ADSS is available in three different TKT spanner for opening and closing of TKT nipples.10 mm.
11 216 100 Cassette holder horizontal R 11 216 073
sizes, depending on the total number of fibres to be spliced and the number Including TKT adapter.
of fibres per cassette. The number of fibres will determine the number of cas- Mid-span cable entry tool with
settes. Please choose a suitable joint closure for your fibre cables as specified 11 216 105 Cassette holder vertical 11 216 110 radius protection.
in the table below.
11 218 xxx For splice protectors, see page
Brackets for attachment on walls or on poles, are available as options.
Together with a locking cap, the closure can easily be locked with a padlock.
Required accessories
ADSS 12, 24, 48 or 72 fibres per Multicassette Choice of cable bushing Choice of bracket
Part No. Type of cable bushing Part No. Type of cable bushing Part No. Type of bracket
Included Required accessories
No. Exterior
ADSS
dia-
meter/ total Weight 11 208 010 End plug PG21 SS 11 212 840 Cable bushing TKT 7x7 mm metal 11 214 102 Pole bracket 800 wood pole
Type of No. of Basic
Part No. height/ lid
fibres height/ kg No. of Choice of cable
mm splice configu- Choice of bracket 11 212 018 Cable bushing 6x6 mm 11 212 842 Cable bushing TKT 7x7 mm plastic 11 214 104 Pole bracket 800 for steel pole
cassettes protectors bushing or end plug
ration*
11 212 040 Cable bushing 4x10 mm 11 212 845 Cable bushing TKT 3x7 mm metal 11 214 114 Mounting plate power line
ADSS 12 Fibre
11 212 050 Cable bushing 1x10 mm 11 212 846 Cable bushing TKT 3x7 mm plastic 11 214 005 Wall bracket
11 160 301 T240/50 ADSS 12/12F 12 270/140/50 1 12 x x
11 160 302 T240/50 ADSS 24/12F 24 270/140/50 2 25 x x 11 212 070 Cable bushing 3x12 mm 11 212 847 Stuffing box nipple TKT M12x1 The bracket for ADSS is found in the table “Bracket”. Make your selec-
tion from the list depending on the application – wooden pole, steel
11 160 304 T240/50 ADSS 48/12F 48 270/140/50 4 50 x x 11 212 100 Cable bushing 2x18mm 11 212 870 Cable bushing TKN-K 1,8-4,0 pole/tower.
11 160 307 T240/70 ADSS 72/12F 72 270/160/70 6 75 x x 11 212 132 Cable bushing 1x24mm 11 212 871 Cable bushing TKN-K 4,0-7,0
11 160 310 T240/150 ADSS 96/12F 96 270/235/150 8 100 x x
11 212 145 Cable bushing 1x30 mm 11 212 872 Cable bushing TKN-K 4x7,0-9,0
11 160 312 T240/150 ADSS 120/12F 120 270/235/150 10 125 x x
11 212 350 Cable bushing divisible 2x18 mm
ADSS 48 Fibre
11 160 331 T240/50 ADSS 24/24F 24 270/140/50 1 25 x x Make a selection from the cable bushing table.
40 41
TB Joint Closure TB Including single fibre splice protectors
Distribution point for up to 56 micro-cables.
Joint Closure TB facilitates mid-span access and as distribution point in
FTTH networks. The closure is delivered with one oval cable inlet and has 5
or 8 open holes for customer adaptation and without end plugs or bushings
which are selected separately. The closure is equipped with cable strength
member clamps, splice protectors and Multicassette. Depending on the
amount of 3-10 mm cables to be installed, the closure TB is delivered in two
different models, TB5 and TB8 as specified in the table below, with the appro-
priate number of cassettes and splice protectors.
End plugs and/or cable bushings are ordered separately. Brackets for at-
tachment on walls, racks, in manholes or on poles, are available as options
and ordered separately. Together with a locking cap, the closure can easily
be locked with a padlock. The closure TB is delivered with heat shrink tube +
branch-off clip for the oval inlet and with the articles specified in the table on
the opposite page (basic configuration).
Accessories & tools R Recommended 11 208 010 End plug PG21 SS 11 212 145 Cable bushing 1x30 mm
Article Article 11 212 018 Cable bushing 6x6 mm 11 212 350 Cable bushing divisible 2x18 mm
11 212 040 Cable bushing 4x10 mm 11 212 840 Cable bushing TKT 7x7 mm metal
11 202 202 Multicassette fibre organizer, 2-p R 11 216 115 Pressure test kit T240
11 212 050 Cable bushing 1x10 mm 11 212 842 Cable bushing TKT 7x7 mm plastic
11 216 020 Tool kit T240 11 218 056 Locking cap for padlock
11 212 070 Cable bushing 3x12 mm 11 212 870 Cable bushing TKN-K 1,8-4,0
TKT spanner for opening and closing of TKT nipples.10 mm. 11 212 100 Cable bushing 2x18mm 11 212 871 Cable bushing TKN-K 4,0-7,0
11 218 346 Splice protectors, pack of 25 R 11 216 073 Including TKT adapter.
Mid-span cable entry tool with 11 212 132 Cable bushing 1x24mm 11 212 872 Cable bushing TKN-K 4x7,0-9,0
11 216 105 Cassette holder vertical 11 216 110 radius protection. Cold method – Insert oval
Basic configuration 11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
11 160 9xx Bottom part 240 Interior fittings Branch -off clip
11 212 853 Insert oval TKN-O 4x 6,5-8,5
Lid 240/150/200 Cable tie 100x2.5 mm Wellbox 240/150/200
Make a selection from the cable bushing table.
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Instruction T240 Swedish/English
O-ring 239.1x8 EPDM Silica gel 10 g Instruction Multicassette
V-clamp 240 Heat shrink 50/16, L = 200 mm Emery cloth
Ordering example of TB closure
FOC, 72 fibre, OD 18 mm, 28x 2F microcables OD 5 mm = 56 fibre, wall mount
Optional accessories
Choice of Choice of Choice of cable
Choice of bracket Choice of work holder Quantity Closure Quantity bracket Quantity bushing
Part No. Type of bracket Part No. Type of work holder 1 11 160 961 1 11 214 029 4 11 212 840
11 214 029 Bracket for TB/TBK 11 216 122 Work holder for TB/TBK 1 11 208 010
42 43
TBK8 Joint Closure TBK8 Including single fibre splice protectors
Distribution point up to 8 standard cables. Optional accessories
Joint Closure TBK8 facilitates mid-span access without the need to cut and
re-splice all the fibres in the cable. The closure is delivered with one oval Cold method – Insert oval
cable inlet and two pre-sealed ports, ID 27 mm and six pre-sealed ports, ID
22 mm. The closure is equipped with cable strength member clamps, splice Part No. Type of cable bushing Part No. Type of cable bushing
protectors and Multicassette.
Joint Closure TBK8 is available in two different sizes, depending on the 11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
total number of fibres to be spliced and the number of fibres per cassette. 11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
The number of fibres will determine the number of cassettes. Please choose
11 212 853 Insert oval TKN-O 4x 6,5-8,5 11 212 891 Insert oval TKN-IO 14-17
a suitable joint closure for your fibre cables as specified in the table below.
Brackets for attachment on walls, racks, in manholes or on poles, are availa- Make a selection from the cable bushing table.
ble as options and ordered separately.
Together with a locking cap, the closure can easily be locked with a pad-
lock. The closure TBK8 is delivered with heat shrink tube + branch-off clip Basic configuration
for the oval inlet and with the articles specified in the table on the opposite 11 160 8xx Bottom part 240 TBK 8 Interior fittings Heat shrink 50/16, L = 200 mm
page (basic configuration).
Lid 240/150/200 Cable tie 100x2.5mm Branch -off clip
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Wellbox 240/150/200
TBK 8 for 12, 24, 48 or 72 fibres per Multicassette O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
Included Optional accessories V-clamp 240 Silica gel 10 g Instruction Multicassette and Emery cloth
No. Exterior
TBK8
dia-
meter/ total Weight No. of Basic
Type of
Part No. height/ lid
fibres height/ kg No. of splice configu- Choice of Choice of Choice of Optional accessories
mm cassettes protectors bracket shrink tube work holder
ration*
Choice of bracket Choice of shrink tube Choice of work holder
TBK8 12 Fibre
11 160 801 T240/150 TBK8 12/12F 12 270/200/150 1 12 x x x Part No. Type of bracket Part No. Type of shrink tube Part No. Type of work holder
11 160 804 T240/150 TBK8 48/12F 48 270/200/150 4 50 x x x 11 214 029 Bracket for TB/TBK 11 219 159 Heat shrink tube 34/8 L = 200 mm 11 216 122 Work holder for TB/TBK
11 160 807 T240/200 TBK8 120/12F 120 270/275/200 10 125 x x x
TBK8 24 Fibre
Ordering example of TBK8 closure
11 160 831 T240/150 TBK8 24/24F 24 270/200/150 1 25 x x x
FOC, 192 fibre, 2x OD 18 mm (in oval), 6x OD 14 mm, wall mounted.
11 160 834 T240/150 TBK8 96/24F 96 270/200/150 4 100 x x x
11 160 837 T240/200 TBK8 240/24F 240 270/275/200 10 250 x x x Choice of Choice of Choice of shrink
Quantity Quantity Quantity
Closure bracket tube
TBK8 48 Fibre
11 160 861 T240/150 TBK8 48/48F 48 270/200/150 1 50 x x x 1 11 160 864 1 11 214 029 6 11 219 159
11 160 864 T240/150 TBK8 192/48F 192 270/200/150 4 200 x x x
11 160 867 T240/200 TBK8 480/48F 480 270/275/200 10 500 x x x
TBK8 72 Fibre
11 160 871 T240/150 TBK8 72/72F 72 270/200/150 1 75 x x x
11 160 874 T240/150 TBK8 288/72F 288 270/200/150 4 300 x x x
11 160 877 T240/200 TBK8 720/72F 720 270/275/200 10 725 x x x
*= Please see next page x= Please make a choice on next page
Article Article
11 216 020 Tool kit T240 11 218 xxx For splice protectors, see page
11 216 111 Cassette holder for TBK 8 R 11 202 202 Multicassette fibre organizer, 2-p
11 218 056 Locking cap for padlock 11 218 340 Branching kit for centre tube cables.
11 216 115 Pressure test kit T240 11 216 131 Tube cutter
44 45
TBK10 Joint Closure TBK10 Including single fibre splice protectors
Distribution point up to 10 standard cables. Optional accessories
The closure is delivered with one open cable inlet 22 mm and two pre-
sealed ports, ID 27 mm, and seven pre-sealed ports, ID 22 mm. The closure Choice of bracket Choice of heat shrink tube Choice of work holder
is equipped with cable strength member clamps, splice protectors and
Multicassette. Joint Closure TBK10 is available in two different sizes, depen- Part No. Type of bracket Part No. Type of heat shrink tube Part No. Type of work holder
ding on the total number of fibres to be spliced and the number of fibres per
cassette. 11 214 029 Bracket for TB/TBK 11 219 159 Heat shrink tube 34/8 L = 200 mm 11 216 122 Work holder for TB/TBK
The number of fibres will determine the number of cassettes. Please
choose a suitable joint closure for your fibre cables as specified in the table Cold method – Insert oval
below. Brackets for attachment on walls, racks, in manholes or on poles, are
available as options and ordered separately. Together with a locking cap, the Part No. Type of cable bushing Part No. Type of cable bushing
closure can easily be locked with a padlock.
The closure TBK10 is delivered with heat shrink tube for the open inlet 11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
and with the articles specified in the table on the opposite page (basic 11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
configuration).
11 212 853 Insert oval TKN-O 4x 6,5-8,5 11 212 891 Insert oval TKN-IO 14-17
Make a selection from the cable bushing table.
TBK10 for 12, 24, 48 or 72 fibres per Multicassette
Basic configuration
Included Optional accessories
TBK10 No. Exterior dia- 11 160 8xx Bottom part 240 TBK 10 Interior fittings Heat shrink 50/16, L = 200 mm
meter/ total Weight No. of Basic
Type of No. of Choice of Choice of Choice of
Part No. height/ lid kg splice configu- Lid 240/150/200 Cable tie 100x2.5mm Branch -off clip
fibres height/ cassettes protectors bracket shrink tube work holder
mm ration* Support sleeve 240 Nut Nylock M6 Din 985 A-4 Wellbox 240/150/200
TBK10 12 Fibre O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
11 160 891 T240/150 TBK10 12/12F 12 270/200/150 1 12 x x x V-clamp 240 Silica gel 10 g Instruction Multicassette and Emery cloth
11 160 894 T240/150 TBK10 48/12F 48 270/200/150 4 50 x x x
11 160 897 T240/200 TBK810 120/12F 120 270/275/200 10 125 x x x Ordering example of TBK10 closure
TBK10 24 Fibre FOC, 240F, 2x OD 20 mm (in oval), 8x OD 14 mm.
11 160 901 T240/150 TBK10 24/24F 24 270/200/150 1 25 x x x
11 160 904 T240/150 TBK10 96/24F 96 270/200/150 4 100 x x x Choice of Choice of Choice of shrink
Quantity Quantity Quantity
Closure bracket tube
11 160 907 T240/200 TBK10 240/24F 240 270/275/200 10 250 x x x
TBK10 48Fibre 1 11 160 907 1 11 214 029 8 11 219 159
11 160 931 T240/150 TBK10 48/48F 48 270/200/150 1 50 x x x
11 160 934 T240/150 TBK10 192/48F 192 270/200/150 4 200 x x x
11 160 937 T240/200 TBK10 480/48F 480 270/275/200 10 500 x x x
TBK10 72 Fibre
11 160 941 T240/150 TBK10 72/72F 72 270/200/150 1 75 x x x
11 160 944 T240/150 TBK10 288/72F 288 270/200/150 4 300 x x x
11 160 947 T240/200 TBK10 720/72F 720 270/275/150 10 725 x x x
*= Please see next page x= Please make a choice on next page
Article Article
11 216 020 Tool kit T240 11 218 346 Splice protectors, pack of 25
11 216 111 Cassette holder for TBK 8 R 11 202 202 Multicassette fibre organizer, 2-p
11 218 056 Locking cap for padlock 11 218 340 Branching kit for centre tube cables.
11 216 115 Pressure test kit T240
46 47
TBK16 Joint Closure TBK16 Including single fibre splice protectors
Distribution point up to 16 standard cables
Joint Closure TBK16 facilitates mid-span access without the need to cut
and re-splice all the fibres in the cable. The closure is delivered with one oval
cable inlet and two pre-sealed ports, ID 25 mm, and 14 pre-sealed ports, ID
16 mm. The closure is equipped with cable strength member clamps, splice
protectors and Multicassette. Joint Closure TBK16 is available in two dif-
ferent sizes, depending on the total number of fibres to be spliced and the
number of fibres per cassette.
The number of fibres will determine the number of cassettes to be used.
Please choose a suitable joint closure for your fibre cables as specified in the
table below. Brackets for attachment on walls, racks, in manholes or on poles,
are available as options and ordered separately.
Together with a locking cap, the closure can easily be locked with a pad-
lock. The closure TBK16 is delivered with heat shrink tube + branch-off clip
for the oval inlet and with the articles specified in the table on the opposite
page (basic configuration).
TBK16 12 Fibre Part No. Type of bracket Part No. Type of heat shrink tube Part No. Type of work holder
11 160 991 T240/150 TBK16 12/12F 12 270/200/150 1 12 x x x
11 214 029 Bracket for TB/TBK 11 219 159 Heat shrink tube 34/8 L = 200 mm 11 216 122 Work holder for TB/TBK
11 160 992 T240/150 TBK16 48/12F 48 270/200/150 4 50 x x x
11 160 993 T240/200 TBK16 120/12F 120 270/275/200 10 125 x x x Cold method – Insert oval
TBK16 24 Fibre
11 160 994 T240/150 TBK16 24/24F 24 270/200/150 1 25 x x x Part No. Type of cable bushing Part No. Type of cable bushing
11 160 995 T240/150 TBK16 96/24F 96 270/200/150 4 100 x x x
11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
11 160 996 T240/200 TBK16 240/24F 240 270/275/200 10 250 x x x
11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
TBK16 48Fibre
11 161 031 T240/150 TBK16 48/48F 48 270/200/150 1 50 x x x 11 212 853 Insert oval TKN-O 4x 6,5-8,5 11 212 891 Insert oval TKN-IO 14-17
11 161 034 T240/150 TBK16 192/48F 192 270/200/150 4 200 x x x Make a selection from the cable bushing table.
48 49
TA Joint Closure TA Beachflex Including single fibre splice protectors
TA Beachflex Accessories & tools R Recommended
Joint Closure TA Beachflex is designed for harsh coastal environments. Joint
Closure TA Beachflex is a complete system used for the transition between Article Article
wire armoured submarine cables and/or land cable. 11 202 202 Multicassette fibre organizer, 2-p 11 218 346 Splice protectors, pack of 25
TA Beachflex consists of a T240 type TA mounted on a strain relief frame
(stainless steel bracket). The cable entries to the joint closure are configured 11 216 020 Tool kit T240 R 11 216 115 Pressure test kit T240
for a variety of applications, such as: 11 216 100 Cassette holder horizontal R 11 218 056 Locking cap for padlock
- TAJ: Joint between two submarine cables with capability of a future branch.
- TAB: Branch between two submarine cables with branching ground cable.
- TAC: Connection between submarine cable and ground cable.
Optional accessories
The closure is equipped with cable strength member clamps, splice pro- Choice of FIMT Choice of earthing kit
+see basic configuration
tectors, Multicassette, sea cable/ground cable bushing, hose clamps and
bracket. Joint Closure TA is available in three different types, depending on Part No. SS tube Nr. of Type of FIMT Part No. Type of earthing kit for sea cable.
ID fibres
the total number of fibres to be spliced. The number of fibres will determine
the number of cassettes. Please choose a suitable joint closure for your fibre 11 218 700 1.93-2.33 FIMT Kit S-tube 1.93-2.33 mm 11 218 650 SS tube Ø 3-7 mm
TAJ TAB TAC
cables as specified in the table below. Together with a locking cap, the clo- 11 218 702 2.4-2.8 FIMT Kit S-tube 2.4-2.8 mm 11 218 654 AL tape, type earth bonding
sure can easily be locked with a padlock. Depending on sea cable type add
11 218 704 2.7-3.4 FIMT Kit S-tube 2.4-3.4 mm Please note, for other types of fibre tubes, copper etc. please contact Tykoflex.
FIMT and potential equalizer (earth strap) kit.
11 218 706 3.2-3.9 FIMT Kit S-tube 3.2-3.9 mm
For underwater sea cable jointing please see more on page 24 and also 11 218 708 4.1-5.2 FIMT Kit S-tube 4.1-5.2 mm
TAJ= Joint TAB= Branch TAC= Connection
contact Tykoflex for information about our SEAFLEX product range. The type of FIMT kit depends on the design of the cable. From the datasheet, note the fibre
stainless steel tube ODx,xx/IDx,xx to select the right kit. For a SS tube 3.6/3.2 mm the Part No:
11218704 FIMT Kit S-tube 2.9-3.4
Beachflex TA Joint Closure, TAJ, TAB or TAC
Exterior Included Optional accessories 11 218 654
TAJ diameter/ Weight
No. of No. of No. of Bracket Basic
24 Fibre Type total height/ Cable bushing Choice of Choice of 11 218 650
Part No. fibres kg casset- splice configu-
lid height/ SS and end plug FIMT earthing kit
mm tes protectors ration*
2x cable bushing 1X24
11 161 171 T240/50 TAJ 24/24F 24 270/140/50 6.0 1 25 1 beach + 1 end plug x x Basic configuration
2x cable bushing 1X24 11 161 1xx Bottom part 240 3 hole Silica gel 10 g
11 161 174 T240/50 TAJ 48/24F 48 270/140/50 6.0 2 50 1 x x
beach + 1 end plug
2x cable bushing 1X24 Lid 240/50 Wellbox TA
11 161 175 T240/50 TAJ 96/24F 96 270/140/50 6.0 4 100 1 x x
beach + 1 end plug
Support sleeve 240 Cable cleaner
O-ring 239.1x8 EPDM Cable bushing 1x24 Beach
Exterior Included Optional accessories
TAB diameter/ Weight Depending
No. of No. of No. of Basic V-clamp 240 Cable bushing 1x24
24 Fibre Type total height/ on type
splice Bracket
fibres kg Choice of Choice of
Part No. lid height/ casset- Cable bushing configu-
SS FIMT earthing kit Interior fittings End plug PG21SS
mm tes protectors ration*
2x cable bushing 1X24 Cable tie 100x2.5mm Bracket SS
11 161 231 T240/50 TAB 24/24F 24 270/140/50 6.5 1 50 1 beach + 1 1X24 x x
Nut Nylock M6 Din 985 A-4 Branching kit for centre tube cables
2x cable bushing 1X24
11 161 234 T240/50 TAB 48/24F 48 270/140/50 6.5 2 75 1 x x
beach + 1 1X24 Washer 6.4x18x1.6 Emery cloth
2x cable bushing 1X24
11 161 235 T240/50 TAB 96/24F 96 270/140/50 6.5 4 150 1 x x Hose clamp
beach + 1 1X24
50 51
TBXL Joint Closure TBXL S Ribbon fibre
Optional accessories
Part No. Work holder (one time) Part No. Bracket Part No. Heat shrink 5 3
11 216 123 Work holder 11 xxx xxx Bracket 11 219 159 Heat shrink 34/8
52 53
T SLIM Joint Closure T SLIM Ribbon fibre with a required choice of splice protectors
Line joint Accessories & tools R Recommended
Joint Closure T SLIM is primarily intended for line joints with the possibility
of up to two branches. The slim design makes its perfect for use in hand- Article Article
holes. Joint Closure T SLIM is delivered with two open cable inlets and two 11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
sealed cable inlets. All inlets can handle cable diameters from 8 to 22 mm.
Two heat shrinks are included. 11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
The closure is equipped with cable strength member clamps and Multi- 11 216 100 Cassette holder R We recommend that you use
cassette. When branching, the inlet is opened and the cable is installed and the Tykoflex Tool kit T240
sealed with heat shrink. T SLIM is available in three different sizes, depending when working with closure
on the total number of fibres to be spliced and the number of fibres per and accessories.
cassette. The necessary cassettes are included depending on the number of
fibres to be used. Also select the number and type of splice protectors. Optional accessories
Brackets for attachment on walls, racks, in manholes or on poles, are avai-
lable as options. Together with a locking cap, the closure can easily be locked Heat shrink (for additional branching) Choice of bracket
with a padlock. Please see table below.
Part No. Type of heat shrink tube Part No. Type of bracket
T SLIM for ribbon fibre 11 219 159 Heat shrink tube 34/8 L = 200 mm 11 214 005 Wall bracket
11 214 030 Pole bracket for horizontal box
Accessories
T SLIM Exterior dia- Included
Required Optional
for ribbon meter/ total Weight
Type No. of fibres
fibre height/ lid kg Basic configuration
Part No. height/ mm No. of Basic confi- Choice of Choice of
Multicassettes guration* Splice protectors heat shrink bracket 11 171 4xx Bottom part 240 4 port Interior fittings 2x Heat shrink 34/8. L=200 mm
11 171 431 T240/30 T SLIM 1MC See below 270/95/30 1 xx x x Lid 240/30/50/70 Cable tie 100x2.5mm Wellbox 240/30/50/70
Support sleeve 240 Nut Nylock M6 Din 985 A-4 Instruction T240 Swedish/English
11 171 432 T240/30 T SLIM 2MC See below 270/95/30 2 xx x x
O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction Multicassette
11 171 434 T240/50 T SLIM 3MC See below 270/115/50 3 xx x x
V-clamp 240 Silica gel 10 g Emery cloth
11 171 435 T240/50 T SLIM 4MC See below 270/115/50 4 xx x x
11 171 437 T240/70 T SLIM 6MC See below 270/135/70 6 xx x x
*= Please see next page x= Please make a choice on next page, xx= Please make a choice below Ordering example of T Slim closure
3x FOC, 96 fibre, 4-ribbon cable OD 12 mm, for wall mounting.
Singlefibre 11 218 080 Ribbon fibre 4/8 25 1 11 171 432 1 11 218 080 1 11 214 005 1 11 219 159
No. of std slim 4-fib. 18x4/cas. 8-fib. 18x8/cas. 12-fib. 9x12/cas.
cassettes 36/cas. 72/cas. 11 218 082 Ribbon fibre 4/8/12 25
1 36 72 72 144 108 11 218 088 Ribbon fibre 4/8 100
2 72 144 144 288 216 11 218 090 Ribbon fibre 4/8/12 100
4 144 288 288 576 432
Mixed installation ribbon and single fibre add
6 216 432 432 864 648 splice protectors below
11 218 346 Single fibre standard 25
11 218 348 Single fibre SLIM 25
The choice of splice protectors
Do not forget to add accurate number of splice protectors accor- 11 218 084 Single fibre standard 100
ding to the type of cable that will be installed. This option ensures 11 218 086 Single fibre SLIM 100
that our Joint Closures have total flexibility to meet all installation
needs. Ribbon fibre and or mixed ribbon fibre and single fibre.
54 55
TS SLIM Joint Closure TS SLIM Ribbon fibre with a required choice of splice protectors
Mid-span Accessories & tools R Recommended
Joint Closure TS SLIM facilitates mid-span access without the need to cut
and re-splice all the fibres in the cable and with the possibility of up to two Article Article
branches. The slim design makes its perfect for use in hand-holes. Joint Clo- 11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
sure TS SLIM is delivered with one open oval cable inlet and two sealed cable
inlets. All inlets can handle cable diameters from 8 to 22 mm. Heatshrink and 11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
clip for the oval inlet are included. 11 216 100 Cassette holder R 11 216 131 Tube cutter 3-16 mm steel tubes We recommend that you use
The closure is equipped with cable strength member clamps and Multi- the Tykoflex Tool kit T240
cassette. When branching, the inlet is opened and the cable is installed and when working with closure
sealed with heat shrink. TS SLIM is available in three different sizes, depen- and accessories.
ding on the total number of fibres to be spliced and the number of fibres per
cassette.
The necessary cassettes are included depending on the number of fibres Optional accessories
to be used. Also select the number and type of splice protectors. Brackets for
attachment on walls, racks, in manholes or on poles, are available as options.
Heat shrink (for additional branching) Choice of bracket
Together with a locking cap, the closure can easily be locked with a padlock.
Part No. Type of heat shrink tube Part No. Type of bracket
Please see table below.
11 219 159 Heat shrink tube 34/8 L = 200 mm 11 214 005 Wall bracket
TS SLIM for ribbon fibre 11 214 030 Pole bracket for horizontal box
Accessories
TS SLIM Exterior dia- Included
Required Optional Basic configuration
for ribbon meter/ total Weight
Type No. of fibres
fibre height/ lid kg
Part No. height/ mm No. of Basic confi- Choice of Choice of 11 171 4xx Bottom part 240 3 inlet Interior fittings Wellbox 240/30/50/70
Multicassettes guration* Splice protectors heat shrink bracket
Lid 240/30/50/70 Cable tie 100x2.5mm Heat shrink 60/15, L=200 mm
11 171 501 T240/30 TS SLIM 1C See below 270/95/30 1 xx x x Support sleeve 240 Nut Nylock M6 Din 985 A-4 Branch -off clip
11 171 502 T240/30 TS SLIM 2C See below 270/95/30 2 xx x x O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
11 171 504 T240/50 TS SLIM 3C See below 270/115/50 3 xx x x V-clamp 240 Silica gel 10 g Instruction Multicassette and Emery cloth
Singlefibre 11 218 080 Ribbon fibre 4/8 25 1 11 171 504 1 11 214 005 1 11 219 159
No. of std slim 4-fib. 18x4/cas. 8-fib. 18x8/cas. 12-fib. 9x12/cas.
cassettes 36/cas. 72/cas. 11 218 082 Ribbon fibre 4/8/12 25
1 36 72 72 144 108 11 218 088 Ribbon fibre 4/8 100
2 72 144 144 288 216 11 218 090 Ribbon fibre 4/8/12 100 Ordering example of T Slim closure
4 144 288 288 576 432
Mixed installation ribbon and single fibre add 3x FOC, 96 fibre, 4-ribbon cable 0D 12 mm, for wall mounting.
6 216 432 432 864 648 splice protectors below
Choice of Splice Choice of Choice of
11 218 346 Single fibre standard 25 Quantity Quantity Quantity Quantity
Closure protectors Bracket heat shrink
11 218 348 Single fibre SLIM 25
1 11 171 502 2 11 218 080 1 11 214 005 1 11 219 159
The choice of splice protectors
11 218 084 Single fibre standard 100
Do not forget to add accurate number of splice protectors accor-
ding to the type of cable that will be installed. This option ensures 11 218 086 Single fibre SLIM 100
that our Joint Closures have total flexibility to meet all installation
needs. Ribbon fibre and or mixed ribbon fibre and single fibre.
56 57
T Joint Closure T Ribbon fibre with a required choice of splice protectors
Line joint Accessories & tools R Recommended
Joint Closure T is primarily intended for line joints with the possibility of
branching. Joint Closure T has three open holes for customer adaptation and Article Article
is delivered without end plugs or bushings which are selected separately.
11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
The closure is equipped with cable strength member clamps and Multicas-
sette. Joint Closure T is available in three different sizes, depending on the
11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
total number of fibres to be spliced and the number of fibres per cassette.
The number of fibres will determine the number of cassettes. 11 216 100 11 216 073 TKT spanner for opening and closing of TKT nipples.10 mm.
Cassette holder horizontal R Including TKT adapter.
Please choose a suitable joint closure for your fibre cables as specified in the
table below and select the number and type of splice protectors. Brackets for 11 216 105 Cassette holder vertical 11 216 110 Mid-span cable entry tool with radius protection.
For TS, TSG, TST, TB and other oval entry models.
attachment on walls, racks, in manholes or on poles, are available as options.
Together with a locking cap, the closure can easily be locked with a padlock.
Required accessories Optional accessories
T for ribbon fibre Choice of cable bushing Choice of bracket
Accessories Part No. Type of cable bushing Part No. Type of cable bushing Part No. Type of bracket
Exterior dia- Included
T for Required Optional
meter/ total Weight
ribbon fibre Type No. of fibres 11 208 010 End plug PG21 SS 11 212 840 Cable bushing TKT 7x7 mm metal 11 214 005 Wall bracket
Part No. height/ lid kg Choice of cable
height/ mm No. of Basic confi- Splice protectors Choice of
bushing or 11 212 018 Cable bushing 6x6 mm 11 212 842 Cable bushing TKT 7x7 mm plastic 11 214 030 Pole bracket for horizontal box
cassettes guration* bracket
end plug
11 212 040 Cable bushing 4x10 mm 11 212 845 Cable bushing TKT 3x7 mm metal 11 214 050 Cable hanger 740, one mounting plate
11 170 201 T240/50 T 1C See below 270/140/50 1 xx x x
11 212 050 Cable bushing 1x10 mm 11 212 846 Cable bushing TKT 3x7 mm plastic Make your choice, depending on if it is pole, wall or manhole.
11 170 202 T240/50 T 2C See below 270/140/50 2 xx x x
11 212 070 Cable bushing 3x12 mm 11 212 847 Stuffing box nipple TKT M12x1
11 170 204 T240/50 T 4C See below 270/140/50 4 xx x x
11 212 100 Cable bushing 2x18mm 11 212 870 Cable bushing TKN-K 1,8-4,0
11 170 207 T240/70 T 6C See below 70/160/70 6 xx x x
11 212 132 Cable bushing 1x24mm 11 212 871 Cable bushing TKN-K 4,0-7,0
11 170 210 T240/150 T 8C See below 270/235/150 8 xx x x
11 212 145 Cable bushing 1x30 mm 11 212 872 Cable bushing TKN-K 4x7,0-9,0
11 170 212 T240/150 T 10C See below 270/235/150 10 xx x x
11 212 350 Cable bushing divisible 2x18 mm
11 170 214 T240/200 T 12C See below 270/290/200 12 xx x x
Make a selection from the cable bushing table. For standard line joints, two ”Cable bushings 1x24”
11 170 216 T240/200 T 14C See below 270/290/200 14 xx x x and one “End plug”, for future branching, would be the choice.
Singlefibre Support sleeve 240 Nut Nylock M6 Din 985 A-4 Instruction Multicassette
No. of 11 218 080 Ribbon fibre 4/8 25
std slim 4-fib. 18x4/cas. 8-fib. 18x8/cas. 12-fib. 9x12/cas. O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Emery cloth
cassettes 36/cas. 72/cas. 11 218 082 Ribbon fibre 4/8/12 25
1 36 72 72 144 108 V-clamp 240 Silica gel 10 g
11 218 088 Ribbon fibre 4/8 100
2 72 144 144 288 216
11 218 090 Ribbon fibre 4/8/12 100
4 144 288 288 576 432
Mixed installation ribbon and single fibre add
Ordering example of T
6 216 432 432 864 648 splice protectors below 2x FOC, 480 fibre 8-ribbon, OD 20 mm and one end plug, for mounting on a wooden pole.
8 288 576 576 1152 864 11 218 346 Single fibre standard 25
10 360 720 720 1440 1080 Choice of Splice Choice of Choice of
Quantity Quantity Quantity Quantity
11 218 348 Single fibre SLIM 25 Closure protectors Bracket cable bushing
12 - - 864 1728 1296
11 218 084 Single fibre standard 100 1 11 170 204 3 11 218 080 1 11 214 030 2 11 212 132
14 - - 1008 2016 1512
16 - - 1152 2304 1728 11 218 086 Single fibre SLIM 100 1 11 208 010
58 59
TS Joint Closure TS Ribbon fibre with a required choice of splice protectors
Mid-span Accessories & tools R Recommended
Joint Closure TS facilitates mid-span access without the need to cut and re-
splice all the fibres in the cable. The closure is delivered with one oval cable Article Article
inlet and has two open holes for customer adaptation. It is delivered without
11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
end plugs or bushings which are selected separately. The closure is equipped
with cable strength member clamps and Multicassette.
11 216 020 Tool kit T240 R 11 218 056 Locking cap for padlock
Joint Closure TS is available in three different sizes, depending on the total
number of fibres to be spliced and the number of fibres per cassette. The 11 216 100 11 216 073 TKT spanner for opening and closing of TKT nipples.10 mm.
Cassette holder horizontal R Including TKT adapter.
number of fibres will determine the number of cassettes. Please choose a sui-
table joint closure for your fibre cables as specified in the table below. Also 11 216 105 Cassette holder vertical 11 216 110 Mid-span cable entry tool with radius protection.
For TS, TSG, TST, TB and other oval entry models.
select the number and type of splice protectors. Brackets for attachment on
walls, racks, in manholes or on poles, are available as options and ordered se-
parately. Together with a locking cap, the closure can easily be locked with a
padlock. The closure TS is delivered with heat shrink tube and branch-off clip Required accessories Optional accessories
for the oval inlet and with the articles specified in the table on the opposite
page (basic configuration).
Choice of cable bushing Choice of bracket
Part No. Type of cable bushing Part No. Type of cable bushing Part No. Type of bracket
TS for ribbon fibre
11 208 010 End plug PG21 SS 11 212 145 Cable bushing 1x30 mm 11 214 005 Wall bracket
Accessories
Exterior dia- Included 11 212 018 Cable bushing 6x6 mm 11 212 350 Cable bushing divisible 2x18 mm 11 214 030 Pole bracket for horizontal box
TS for Required Optional
meter/ total Weight
ribbon fibre Type No. of fibres 11 212 040 Cable bushing 4x10 mm 11 212 840 Cable bushing TKT 7x7 mm metal 11 214 050 Cable hanger 740, one mounting plate
Part No. height/ lid kg Choice of cable
height/ mm No. of Basic confi- Splice protectors Choice of
bushing or 11 212 050 Cable bushing 1x10 mm 11 212 842 Cable bushing TKT 7x7 mm plastic Make your choice, depending on the application
cassettes guration* bracket
end plug - a pole, wall or manhole.
11 212 070 Cable bushing 3x12 mm 11 212 860 Cable bushing TKN-L 1,8-4,0
11 170 401 T240/50 TS 1C See below 270/140/50 1 xx x x
11 212 100 Cable bushing 2x18mm 11 212 861 Cable bushing TKN-L 4,0-7,0
11 170 402 T240/50 TS 2C See below 270/140/50 2 xx x x
11 212 132 Cable bushing 1x24mm 11 212 862 Cable bushing TKN-L 4x7,0-9,0
11 170 404 T240/50 TS 4C See below 270/140/50 4 xx x x
Cold method – Insert oval
11 170 407 T240/70 TS 6C See below 270/160/70 6 xx x x
11 212 851 Insert oval TKN-O 4x 5,0-7,0 11 212 854 Insert oval TKN-O 4x 7,7-9,5
11 170 410 T240/150 TS 8C See below 270/235/150 8 xx x x
11 212 852 Insert oval TKN-O 2x 5,5-7,2 11 212 855 Insert oval TKN-O 10-12
11 170 412 T240/150 TS 10C See below 270/235/150 10 xx x x
11 170 414 T240/200 TS 12C See below 270/290/200 12 11 212 853 Insert oval TKN-O 4x 6,5-8,5
xx x x
11 170 416 T240/200 TS 14C See below 270/290/200 14 Make a selection from the cable bushing table.
xx x x
11 170 418 T240/200 TS 16C See below 270/290/200 16 xx x x
*= Please see next page x= Please make a choice on next page, xx= Please make a choice below Basic configuration
11 170 4xx Bottom part 240 3 TS Interior fittings Heat shrink 50/16, L =200 mm.
Fibre capacity for T with 1 to 16 Multicassettes Required splice protectors
Lid 240/50/70/150 Cable tie 100x2.5mm Branch -off clip
Singlefibre 11 218 080 Ribbon fibre 4/8 25
No. of Support sleeve 240 Nut Nylock M6 Din 985 A-4 Wellbox 240/50/70/150
std slim 4-fib. 18x4/cas. 8-fib. 18x8/cas. 12-fib. 9x12/cas.
cassettes 11 218 082 Ribbon fibre 4/8/12 25
36/cas. 72/cas.
O-ring 239.1x8 EPDM Washer 6.4x18x1.6 Instruction T240 Swedish/English
1 36 72 72 144 108 11 218 088 Ribbon fibre 4/8 100
V-clamp 240 Silica gel 10 g Instruction Multicassette and Emery cloth
2 72 144 144 288 216 11 218 090 Ribbon fibre 4/8/12 100
4 144 288 288 576 432 Mixed installation ribbon and single fibre add
splice protectors below
6 216 432 432 864 648 Ordering example of TS
8 288 576 576 1152 864 11 218 346 Single fibre standard 25
3x FOC, 432 fibre 4-ribbon, OD 21 mm, Mid-span, for wall mounting.
10 360 720 720 1440 1080 11 218 348 Single fibre SLIM 25
12 - - 864 1728 1296 11 218 084 Single fibre standard 100 Choice of Splice Choice of Choice of
Quantity Quantity Quantity Quantity
11 218 086 Single fibre SLIM 100 Closure protectors Bracket cable bushing
14 - - 1008 2016 1512
16 - - 1152 2304 1728 1 11 170 407 1 11 218 088 1 11 214 005 1 11 212 132
1 11 218 080 1 11 208 010
The choice of splice protectors
Do not forget to add accurate number of ble that will be installed. This option ensures to meet all installation needs. Ribbon fibre
splice protectors according to the type of ca- that our Joint Closures have total flexibility and or mixed ribbon fibre and single fibre.
60 61
TSG Joint Closure TSG Ribbon fibre with a required choice of splice protectors
Mid-span branching Accessories & tools R Recommended
Joint Closure TSG facilitates mid-span access without the need to cut and
re-splice all the fibres in the cable. The closure is delivered with one oval Article Article
cable inlet and two pre-sealed ports, ID 25 mm, and four pre-sealed ports,
11 202 202 Multicassette fibre organizer, 2-p 11 216 115 Pressure test kit T240
ID 16 mm. The closure is equipped with cable strength member clamps and
Multicassette. Joint Closure TSG is available in three different sizes, depen-
11 216 020 Tool kit T240 11 218 056 Locking cap for padlock
ding on the total number of fibres to be spliced and the number of fibres per
cassette. The number of fibres will determine the number of cassettes. 11 216 100 11 216 073 TKT spanner for opening and closing of TKT nipples.10 mm.
Cassette holder horizontal R Including TKT adapter.
Please choose a suitable joint closure for your fibre cables as specified in
the table below. Also select the number and type of splice protectors. Brack- 11 216 105 Cassette holder vertical 11 216 110 Mid-span cable entry tool with radius protection.
For TS, TSG, TST, TB and other oval entry models.
ets for attachment on walls, racks, in manholes or on poles, are available as
options and ordered separately. Together with a locking cap, the closure can
easily be locked with a padlock. The closure TSG is delivered with heat shrink
tube + branch-off clip for the oval inlet and with the articles specified in the Optional accessories
table on the opposite page (basic configuration).
Choice of heat shrink tube Choice of bracket Choice of cable bushing
TSG for ribbon fibre
Part No. Type of heat shrink tube Part No. Type of bracket Part No. Type of cable bushing
Accessories
Exterior dia- Included 11 219 159 Heat shrink tube 34/8 L = 200 mm 11 214 005 Wall bracket
11 212 845 Cable bushing TKT 3x7 mm metal
TSG for Required Optional
meter/ total Weight 11 212 846 Cable bushing TKT 3x7 mm plastic
ribbon fibre Type No. of fibres 11 219 035 Heat shrink end cap 50/25 for oval inlet. 11 214 030 Pole bracket for horizontal box
Part No. height/ lid kg No. of Basic Choice of cable
height/ mm Splice Choice of heat Choice of 11 212 850 Cable bushing TKT 1x11 mm metal
cass- configu- bushing or 11 214 050 Cable hanger 740, one mounting plate
protectors shrink tube bracket
ettes ration* end plug
The bracket for T240 is found in the table above. Select a bracket depend- Make a selection from the cable bushing table. Cable bushing TKT fits
11 170 501 T240/50 TSG 1C See below 270/140/50 1 xx x x x ing on whether the application is a wooden pole or steel pole/tower. on the four 18 mm inlets above the oval inlet.
62 63
Joint Closure TBXL R The T240 custom design
High fibre count up to 1728 fibres Examples of custom design.
Joint Closure TBXL R is developed for ribbon fibre cables for up to 1728
fibres. Joint Closure TBXL R is delivered with one open oval inlet 63x31 mm
(for mid-span access) and two ID 35 mm sealed cable inlets, four ID 25 mm
sealed cable inlets and two open holes.
TBXL R is equipped with nine permanent pivoting splice trays for a maxi-
mum of 192 fibres (8-ribbon). The closure is equipped with cable strength
member clamps and splice protectors. Brackets for installation are available
as options and ordered separately.
Together with a locking cap, the closure can easily be locked with a pad-
lock. The closure TBXL R is delivered with heat shrink tube and branch-off
clip for the oval inlet and with the articles specified in the table below (basic
configuration).
11 218 080 Ribbon fibre 4/8 25-p 11 216 123 Work holder 11 xxx xxx Bracket 11 219 159 Heat shrink 34/8
11 218 082 Ribbon fibre 4/8/12 25-p
Underground ODF with 96 SC connectors. Fibre splitter, converters and PON. Termination and splicing, e.g. in wind turbines.
11 218 088 Ribbon fibre 4/8 100-p Accessories & tools R Recommended
Basic configuration
11 162 003 Bottom part 240/TBXL Pivoting splice trays Emery cloth
V-clamp 240 Branch-off clip Silica gel 10 g
Support sleeve 240 Heat shrink WCSM 54/16 L = 200 mm Cable tie 100x2.5mm
O-ring 239.1x8 EPDM Branching kit for centre tube cables Instruction TBXL
Interior fittings TBXL
64 65
Our new cold compression method
11 212 854 Cable entry TKN-O 4x 7.7 to 9.5 grey rubber seal 4 holes. Three 1
An installation example of Joint closure TMC with 7 mm Testing of the cold method plugs are included.
duct secured in duct holder. A 2 mm micro cables connected to the Joint
Closure via bushing TKN-K 1.8-4.0. 14/10 duct has micro cable connected in
oval (mid-span) with TKN-O 5.0-7.0.
11 212 855 Cable entry TKN-O 2x9,5-12,0 black rubber seal 2 holes. Two 1
Temp plugs are included.
Pressure
Information
Part number Nr. of cables Cable diameter
11 212 851 4 Cable Ø 5,0-7,0 mm 11 212 862 Cable entry TKN-L 4x7,0-9,0mm 1
Cable entryTKN-L 7,0-9,0 blue rubber seal 4 holes.
4 plugs included.
11 212 852 2 Cable Ø 5,5-7,2 mm
11 212 853 4 Cable Ø 6,5-8,5 mm Cable entry TKN-K 1,8-4,0/4,0-7,0/7,0-9,0 • • • 11 212 870 Cable entry TKN-K 1.8-4.0 black rubber seal 24 holes. 24 plugs 1
included. A maximun of 24 cables with a size of 1.8-3.0 mm.
A maximum of 14 cables with a size of 3.1-4.0 mm. 10 holes in
11 212 854 4 Cable Ø 6,5-8,5 mm the outer ring are sealed with blind plugss.
11 212 855 2 Cable Ø 9,5-12 mm 11 212 871 Cable entry TKN-K 4.0-7.0 black rubber seal 12 holes. 12 plugs 1
included.
66 67
Cable bushings of stainless steel and accessories
Part No. Description Pack
Cable bushing TKT - cold sealing
For cables and ducts 3-7 mm, with complete sealing kit,
Mastic tape and instruction manual. All branchings are presealed at delivery. 2x18 oval for two cables 9-18 mm diameter.
11 212 100 Heat shrink 50/16, L=200 mm. Insert clip. 1
Part No. Description Pack
TKT 7x7 plastic. Seven branchings for 3-7 mm cables. 1x30, for cable diameter 17-30 mm.
11 212 842 TKT is a cable bushing for open cable bushing ports 28.3 mm. 1 11 212 145 1
Heat shrink 50/16, L=200 mm.
7 plastic nipples and Mastic tape included.
TKT-S 1x11 mm
11 212 850 Mountable on cable entry pipe 18 mm outer diameter. (for example, TSG). 1 Split cable bushing, 2x16 oval pipes for two cables 7-18 mm diameter.
Mastic tape included. 11 212 350 Ability to add new cable parallel with old cable in existing entry, 1
without disturbing traffic. Heat shrink 55/12, L=170 mm divisible.
With flange nut and O-ring. For mounting on closure with open cable bushing ports 28.3 mm. Kit including emery cloth, heat protection Blind plug with flange nut and O-ring. Use Flange nut spanner 11216020 B,
aluminium tape and shrink tubes for all pipes. Use flange nut spanner 11 216 020 B, for mounting of cable bushings and blind plugs. 11 208 010 1
for mounting of cable bushings and blind plugs.
Part No. Description Pack
Heat shrink tubes for sealing of cables in cable entry pipes and for other sealings. Max/min diameter - length.
1x10, for cable with inner diameter 5.5-10 mm. Part No. Description Pack
11 212 050 Heat shrink 16/5, L=100 mm. 1
11 219 110 Heat shrink tube Ø3-10 mm, 100 mm. 1
11 219 123 Heat shrink tube Ø5-16 mm, 100 mm. 1
2x10, for cable with inner diameter 5.5-10 mm. 11 219 149 Heat shrink tube Ø8-25 mm, 200 mm. 1
11 212 060 1
2x heat shrink 16/5, L=100 mm. 11 219 159 Heat shrink tube Ø8-34 mm, 200 mm. 1
11 219 169 Heat shrink tube Ø12-35 mm, 200 mm. 1
11 219 189 Heat shrink tube Ø16-50 mm, 200 mm. 1
3x12, for cable with inner diameter 5.5-12 mm. 11 219 192 Heat shrink tube Ø19-63 mm, 200 mm. 1
11 212 070 1
3x heat shrink 16/5, L=100 mm.
4x10, for cable with inner diameter 5.5-10 mm. 11 219 300 Zip shrink tube 55/12-170 mm. 1
11 212 040 1
4x heat shrink 16/5, L=100 mm.
68 69
Accessories
11 202 204 Multicassette for 48 single fibre. With 9 slots + additional 2x4 slots for splice protectors. 2-pack
11 202 100 Storage tray for pan closure, i.e. TSG. For mid-span fibre overlength. 1
11 216 100 Cassette holder horizontal, for all side entry, ”pan” closures (A) 1
A
B 11 216 105 Cassette holder vertical, for bottom entry, ”dome” closures (B) 1 11 216 122 Work position holder – for handling type TB, TBK, TBXL, bottom entry dome closures. 1
C
11 216 110 Mid-span cable entry tool with radius protection. 11 218 056 Locking cap for padlock. 1
1
For TS, TSG, TST, TB and other oval entry models.
Mounting
Part No. Description Pack
Cable hanger
.005 11 214 005 Mounting bracket, wall or rack for hooked or fixed mounting. 1
Part No. Description Pack
.030
11 214 030 Pole bracket for horizontal closure. 1
11 214 050 Cable hanger 740, one mounting plate. 1 11 214 040 Pole bracket for vertical closure. 1
.029
.040
11 214 029 Bracket for TB and TBK 1
70 71
Accessories Export information
Tube cutters
Part No. Description Pack
Splice protectors Well container 1/1 size with Joint Closure T 240/50, 44 pieces.
Part No. Description Pack
11 218 346 Splice protectors for single fibre standard 25-pack A full pallet.
11 218 080 Splice protectors for ribbon fibre 4/8 25-pack Volume: 1,2 x 0,8 x 0,93 = 0,8928m³ = 0,90 m³
Weight: 44 x 4 = 176 + 10 + 4 = 190 kg
11 218 082 Splice protectors for ribbon fibre 4/8/12 25-pack
11 218 084 Splice protectors for single fibre standard 100-pack
11 218 086 Splice protectors for single fibre SLIM 100-pack
11 218 088 Splice protectors for ribbon fibre 4/8 100-pack
11 218 090 Splice protectors for ribbon fibre 4/8/12 100-pack
Other accessories
Part No. Description Pack
11 216 140 Knipex Oetiker plier, to crimp Oetiker clamp in 11 218 340 1
Pressure test
Part No. Description Pack
11 216 115 Pressure test kit for T240, Lid, air overpressure pump and air bubble indicator. Kit
72 73
Made to guarantee reliable jointing in very demanding conditions
Tightness for overpressure and vacuum
Closures installed in manholes or direct 90o 60o Big and small
burried can be exposed of flooding Maximum use of interior space with as little wasted
and stay under water for months. 30o space as possible gives compact outer dimensions. This
Tykoflex closure therefor tested and allows placement in small and narrow manholes.
certified for IP68 (2 bar/24 h) IP69 and
0o
IP69K.
-30o Round for a reason
-60 o Allows largest possible fibre bending radius, with safe
storage and easy fibre handling in the large Multicas-
Universality -90 o
sette. All in a very compact closure solution. The round
The unique Multicassette fibre organizer is used construction makes the closure very easy to open and
Closure under test with high pressure water jet, 100 bar, 80°C, 0° to 180° angle.
for splicing of single fibre as well as ribbon. One cas- close safely with only one screw. The round construc-
sette and the same installation procedure for all needs. tion with the o-ring seal guarantees safe sealing. Withstands rough handling.
Flexibility
International and European standard Install the closure for the demands of today and the
Fulfils International and European standard for outside capacity of tomorrow. T240 closures are designed to be
plant closures IEC 61753-111-7 easy to expand, branch off and re-configure.
IEC 61753-111-8, IEC 61753-111-9, CENELEC EN 50411-
2-2 (pan closures), CENELEC EN 50411-2-4 (dome
closures).
The T240 closure is reliable in extreme temperatures.
Solid T240 closure with safe locking device
T240 closure in water-filled manhole. Rodents can eat through concrete, but not through stainless steel. Weather is unpredictable – T240 is reliable. Example of OPGW installation.
74 75
Tykoflex T240 installation movies
1 2 3 4 5 6
7 8 9 10 11 12