Professional Documents
Culture Documents
[PRECAUTIONS FOR EXCLUSIVE AUTHORIZATION CONTROL] No. Name Description - Module de communication MELSECNET/H (GT15-J71LP23-25, GT15-
WARNING 2. Part Names and Settings With a switching function for accepting and stopping the access
to the SD card
J71BR13)
- Module de communication CC-Link (GT15-J61BT13)
12) SD card cover - Couvercle de protection contre l’huile
Make sure to fully understand the GOT network interaction function before When the cover is opened : Access is prohibited
The following shows the part names for GT2715, GT2712, GT2710, GT2708 and When the cover is closed : Access is allowed *3: Do not use or store the GOT under pressure higher than the atmospheric
using this function to control the authorization among pieces of equipment to GT2705. pressure of altitude 0m (0ft.).
prevent simultaneous operations. 13) Battery holder Houses the battery
Failure to observe this instruction may cause a malfunction.
The exclusive authorization control of the GOT network interaction function 14) Side interface For installing a communication unit
can be enabled or disabled for each screen.
GT2715 1)2) 7) 7) 8) 9) 7) When an air purge is made inside the control panel by adding pressure, there
For connecting a USB mouse, a USB keyboard, or a USB may be a clearance between the surface sheet and the screen making it difficult
(For all screens, the exclusive authorization control is disabled by default.) USB interface
10) 15) barcode reader, and transferring or saving data (Connector to use the touch panel, or the sheet may come off.
Properly determine the screens for which the exclusive authorization control 6) (Host/Back face)
shape: TYPE-A)
is required, and set the control by screen. *4: This indicates the section of the power supply to which the equipment is
11)12) Hole for attaching a cable clamp for preventing USB cable from
A screen for which the exclusive authorization control is disabled can be Hole for attaching a assumed to be connected between the public electrical power distribution
16) being pulled out (Recommended product: RSG-130-V0 of network and the machinery within the premises.
operated simultaneously from pieces of equipment. cable clamp
5) 7) 7) KITAGAWA INDUSTRIES CO.,LTD. or equivalent) Category II applies to equipment for which electrical power is supplied from
Make sure to determine the operation period for each operator, fully grasp the
circumstances of the field site, and ensure safety to perform operations. 13) Terminating resistor fixed facilities.
For switching on and off of the terminating resistor for the RS-
20) 14) 17) setting switch The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.
3) 422/485 communication port (Default (Off))
(Inside cover)
[DISPOSAL PRECAUTIONS] 4) 15)
Auxiliary extension
*5: This index indicates the degree to which conductive material is generated in the
environment where the equipment is used.
16) 18) For installing an option unit
CAUTION interface In pollution degree 2, only non-conductive pollution occurs but temporary
7) 23) 7) 17) 7) 19) Extension interface*1 For installing a communication unit or an option unit conductivity may be produced due to condensation.
When disposing of this product, treat it as industrial waste. 19) 18) Vertical installation For the vertical installation, install the GOT so that the arrow *6: Some models have ANSI/ISA12.12.01 approval for use in Class I, Division 2
When disposing of batteries, separate them from other wastes according to 24) 22) 20)
arrow mark points upward. (ANSI/ISA 12.12.01, C22.2 No.213-M1987) hazardous locations.
the local regulations. 23) 21) For the details, please contact your local sales office.
(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the 21) Power terminal Power input terminal, LG terminal, FG terminal
For communicating with a controller or connecting a personal *7: This is for use on a flat surface of a Type 1 enclosure.
battery directive in the EU member states.) 22) Ethernet interface
GT2712 1)2) 7) 27) 8) 9) 7) computer (Connector shape: RJ45 (modular jack)) Point
[TRANSPORTATION PRECAUTIONS] Ethernet
SD/RD LED ON: Data sent or received Refer to the GOT2000 Series User’s Manual (Hardware) for details on the performance
6) 10) SD/RD LED OFF: Data not sent or received
23) communication status specifications of each GOT.
CAUTION 27) 11)12) LED
SPEED LED ON: Communicating at 100 Mbps
SPEED LED OFF: Communicating at 10 Mbps or disconnected
When transporting lithium batteries, make sure to treat them based on the 5)
20) 27)
For communicating with a controller (Connector shape: D sub
3.2 Power Supply Specifications
transport regulations. 13) 24) RS-232 interface The following indicates the power supply specifications for GT27.
9-pin (male))
(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the 3) 14)
Note
regulated models.) 15) For communicating with a controller (Connector shape: D sub
4) 25) RS-422/485 interface
Make sure to transport the GOT main unit and/or relevant unit(s) in the 16) 9-pin (female)) Operation at momentary failure
manner they will not be exposed to the impact exceeding the impact 26)
USB interface For connecting personal computers (Connector shape: Mini-B) • If an instantaneous power failure occurs in the power supply and continues for more
resistance described in the general specifications of this manual, as they are 7) 23) 27) 19) 18) 17) 7) (Device/Back face) (Only GT2712-STWA/D,GT2710-VTWA/D) than the permissible period, the GOT will be reset.
precision devices. For fixing the GOT to the control panel to make the GOT • Make sure to power on the unit more than 5 seconds after power-off.
Failure to do so may cause the unit to fail. 26) 24) 21) Special installation
27) conform to the ATEX/KCs standard. (Only GT2712-STWA/D,
Check if the unit operates correctly after transportation. 25) 22) fitting mounting hole*2
GT2710-VTWA/D) 3.2.1 For GOTs powered from the 100 to 240VAC
When fumigants that contain halogen materials such as fluorine, chlorine,
bromine, and iodine are used for disinfecting and protecting wooden GT2710 1)2) 7) 8) 9) 7) *1:GT2705-V when used, for using multiple extension units, a barcode reader or an power supply
packaging from insects, they cause malfunction when entering our products. RFID controller, the total current for the extension units, barcode reader or RFID Specifications
Please take necessary precautions to ensure that remaining materials from 10) controller must be within the current that the GT2705-V can supply. refer to the GT2710-STBA
fumigant do not enter our products, or treat packaging with methods other 11)12) following GOT2000 Series Use’s Manual. Item GT2712-STBA GT2710-VTBA GT2708-STBA
than fumigation (heat method). 27) GT2715-XTBA GT2712-
GT2710- GT2708-VTBA
27) *2:Special installation fittings are sold separately. If you need the special installation STWA VTWA
Additionally, disinfect and protect wood from insects before packing products. 5) 20)
13) fittings, consult your local sales office. Power supply voltage AC100 to 240VAC (+10%, -15%)
14)
3) Power frequency 50/60Hz 5%
15)
Manuals 4) 16) Max. apparent power 140VA 100VA
The following shows manuals relevant to this product. 3. Specifications maximum load 51W or less 44W or less 41W or less
7) 23) 19) 18) 7) Power
Stand alone 25W 19W 17W 15W
Manual name Manual number (Model code) 17) consum
26) 24) 21) 3.1 General Specifications ption Stand alone with
backlight off
10W
GOT2000 Series User’s Manual (Hardware) SH-081194ENG (1D7MJ5) 25) 22)
Item Specifications 40A or less (3ms,
60A or less (2ms, operating ambient
operating ambient
GOT2000 Series User’s Manual (Utility) SH-081195ENG (1D7MJ6) Inrush current temperature 25,
GT2708 1)2) 7) 8) 9) 7) Operating ambient maximum load)
temperature 25, maximum load)
For detailed manuals and relevant manuals, refer to the e-Manual or PDF temperature*1 *2 Allowable momentary power
0 to 55 20 ms or less (100VAC or more)
manuals stored in the DVD-ROM for the screen design software used. 10) Température *2 failure time
0 à 55
11)12)13) ambiante de
The latest manuals are also available from MITSUBISHI ELECTRIC FA Global 1,500Vp-p noise voltage, 1 s noise width (when
5) fonctionnement*1
20) Noise immunity measuring with a noise simulator under 25 to 60Hz
Website (www.MitsubishiElectric.com/fa). Storage ambient
14) -20 to 60 noise frequency)
3) temperature
Referenced Standard: GB/T15969.2 4) 15)
Operating ambient
Dielectric withstand voltage 1500VAC for 1 minute across power terminals and earth
(Requirement of Chinese standardized law) 10 to 90% RH, non-condensing 10M or more across power terminals and earth by a
humidity Insulation resistance
7) 23) 19) 18) 7) 500V DC insulation resistance tester
Storage ambient
Before using the GOT 16) 24) 21)
17)
humidity
10 to 90% RH, non-condensing Applicable wire size 0.75[mm2] to 2[mm2]
Connect the connector of the GOT to the connector of the battery. 25) 22) Half- Sweep Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,
Frequency Acceleration amplitude Applicable solderless terminal
Refer to the GOT2000 Series User’s Manual (Hardware) for the connection count V2-N3A, FV2-N3A
instructions. 5 to 10 times Applicable tightening torque
For details on the GOT specifications, installing instructions, wiring, maintenance GT2705 1)2) 7) 7) Compliant Under 8.4Hz - 3.5mm
each in X, (Terminal block terminal screw)
0.5[N•m] to 0.8[N•m]
and inspection, or checking procedure for the version and the compatible standard, with JIS B intermittent Y and Z
8.4 to
refer to the GOT2000 Series User’s Manual (Hardware). 5) 14) 9) Vibration resistance 3502 and vibration 150Hz
9.8m/s2 - directions 3.2.2 For GOTs powered from the 24VDC power
8) IEC
10)
Packing List 3) 20) 11)12)13) 61131-2 Under
5 to
- 1.75mm supply
8.4Hz
The GOT product package includes the following: 4) 15) continuous
8.4 to
-
vibration 4.9m/s2 - Specifications
Description Quantity 150Hz GT2710-
7) 7)
GT27 1 Compliant with JIS B 3502 and IEC 61131-2 147 m/s2(15G), Item
GT2712- STBD, GT2708-
19) 23) 17) Shock resistance GT2715- STBD, GT2710- STBD, GT2705-
25) 22) 3 times each in X, Y and Z directions XTBD GT2712- VTBD, GT2708- VTBD
Battery (GT11-50BAT) (Attached to the GOT) 1
24) 21) Operating No greasy fumes, corrosive gas, flammable gas*6, excessive STWD GT2710- VTBD
4, VTWD
Installation fitting atmosphere conductive dust, and direct sunlight (Same as storage atmosphere)
8(Only GT2715) No. Name Description Power supply voltage DC24V (+25%, -20%)
Operating altitude *3 2000 m (6562 ft) max.
GT27 General Description (This manual) 1 1) Display screen Displays the utility and the user-created screen. 48W or 45W or 42W or 39W or 30W or
Installation location Inside control panel maximum load
Power less less less less less
GT27 本体概要説明書 1 For operating the touch switches in the utility and the user- Overvoltage
2) Touch Panel II or less consu Stand alone 23W 18W 15W 13W 7W
GOT2000 Series Supplementary Description 1(Only GT2712-STWD, created screen category *4 mption Stand alone with
(Compliance with the ATEX Directive) GT2710-VTWD) For connecting a USB mouse, a USB keyboard, or a USB Pollution degree *5 2 or less 8W 8W 8W 8W 5W
barcode reader, and transferring or saving data (Connector backlight off
1(Only GT2712-STWD, Cooling method Self-cooling 69A or less
GOT2000 시리즈 보충 설명 (KCs 지침 준수 ) GT2710-VTWD) USB interface shape: TYPE-A)
3) Grounding with a ground resistance of 100 Ω or less by using a ground 5A or less (20ms, operating ambient temperature (1ms, operating
(Host/Front face) (Only GT2715-XTBA/D, GT2712-STBA/D, GT2710-STBA/D, Inrush current ambient
Grounding cable that has a cross-sectional area of 2 mm2 or more. 25, maximum load) temperature 25,
GT2710-VTBA/D, GT2708-STBA/D, GT2708-VTBA/D, maximum load)
If impossible, connect the ground cable to the control panel.
1. FEATURES GT2705-VTBD)
For connecting a personal computer (Connector shape: Mini-B) Type rating UL Type 1 *7
Allowable momentary
power failure time
10 ms or less
USB interface (Device (Only GT2715-XTBA/D, GT2712-STBA/D, GT2710-STBA/D, 500Vp-p noise voltage, 1 s noise width (when measuring with
(1) Abundant standard equipment 4)
/Front face) GT2710-VTBA/D, GT2708-STBA/D, GT2708-VTBA/D, *1: The operating ambient temperature includes the temperature inside the Noise immunity
• Variety of connection with FA devices a noise simulator under 25 to 60Hz noise frequency)
GT2705-VTBD) enclosure of the control panel to which the GOT is installed. Dielectric withstand
• SD card interface compatible with the SDHC card having a large capacity La température ambiante de fonctionnement inclut la température à l'intérieur 350VAC for 1 minute across power terminals and earth
and allowing high-speed communication Lit in blue : Power is properly supplied. voltage
• Connection with various peripheral devices with the USB host Lit in orange : Screen saving du boîtier du tableau de commande sur lequel le GOT est installé. 10M or more across power terminals and earth by a 500V DC
5) POWER LED Insulation resistance
(2) Improved usability Blinks in orange/blue : Backlight failure *2: When any of the following units and option is mounted on the GOT, the insulation resistance tester
• Abundant troubleshooting Not lit : Power is not supplied maximum operating ambient temperature must be 5°C lower than the one
Applicable wire size 0.75[mm2] to 2[mm2]
• Easy and clear screen creation 6) Human sensor Detects human movement.(Only GT2715, GT2712) described above.
• PC-like operation screen 7) Unit installation fitting Mounting fixtures for fixing the GOT to the control panel - Multimedia unit (GT27-MMR-Z) Applicable solderless Solderless terminal for M3 screw RAV1.25-3, V2-S3.3, V2-
• Multi-touch function, Gesture function - MELSECNET/H communication unit (GT15-J71LP23-25 or GT15-J71BR13) terminal N3A, FV2-N3A
8) Reset switch Hardware reset switch
• Support for the vertical installation - CC-Link communication unit (GT15-J61BT13) Applicable tightening
9) Installation switch Used for OS installations at the GOT startup torque (Terminal block 0.5[N•m] to 0.8[N•m]
(3) Enhanced compatibility with Mitsubishi Electric FA devices - Protective cover for oil
(4) Easy replacement Lit : SD card mounted terminal screw)
Blinking : SD card accessed Lors du montage du module ou de l'option suivant, la température ambiante de
(5) LED backlight 10) SD card access LED fonctionnement doit être réduite de 5°C par rapport aux valeurs maximales
(6) External controllers including multimedia and video supported (excluding No lit : SD card not mounted or SD card mounted
(removable) dans les spécifications générales.
GT2705) - Module multimédia (GT27-MMR-Z)
(7) Various extended functions supported 11) SD card interface For installing a SD card
3.3 External Dimensions 4.1.1 EMC directive Our test has been carried out on a panel having the damping Category I has the lowest durability; category IV has the highest
characteristics of 37dB max. and 30dB mean (measured by 3m durability.
GT2715 GT2712 method with 30 to 300MHz).
397(15.63) 316(12.44) The standards of the EMC Directive are shown below.
(0.39)
(0.39)
(0.79)
(2) Connection of power and ground wires
10
10
20
322(12.68) 241(9.49) Applied
Test standard Test details Standard value Ground and power supply wires for the GOT must be connected as
standard
30M-230MHz QP: described below.
227(8.94)
246(9.69)
300(11.81)
281(11.06)
Electromagnetic 30dB V/m (30m in (a) Provide a grounding point near the GOT. Short-circuit the LG and
CISPR16-2-3 emissions from the measurement range)*2, *3 FG terminals of the GOT (LG: line ground, FG: frame ground)
Radiated noise*1 product are 230M-1000MHz QP: and ground them with the thickest and shortest wire possible
measured. 37dB V/m(30m in
(The wire length must be 30cm (11.81in.) or shorter.) Category IV Category III Category II Category I
measurement range)*2, *3
(0.39)
46(1.81)
(0.24)
241(9.49) The LG and FG terminals function is to pass the noise generated
10
Electromagnetic 150k-500kHz QP: 79dB, Installation category
6
(0.24)
(2.05)
60(2.36)
10(0.39)
CISPR16-2-1 emissions from the Mean: 66dB *2 Category II indicates a power supply whose voltage has been reduced
52
6
Conducted noise*1 product to the power 500k-30MHz QP: 73dB, as possible must be ensured. As the wires are used to relieve the
301(11.85)
line is measured. Mean: 60dB *2
by two or more levels of isolating transformers from the public power
noise, the wire itself carries a large noise content and thus short distribution.
10(0.39) 382(15.04) 10(0.39) Immunity test in wiring means that the wire is prevented from acting as an
GT2710 GT2708 IEC61000-4-2
Electrostatic
which static
electricity is applied
4kV Contact discharge antenna. 4.2.3 Control panel
303(11.93) 241(9.49)
(0.39)
(0.39)
8kV Aerial discharge Note) A long conductor will become a more efficient antenna at
immunity*1 to the cabinet of the Because the GOT is open type equipment (device designed to be stored
10
10
panel.
175(6.89)
218(8.58)
199(7.83)
Radiated which field is 1.4-2GHz:3V/m the power supply wires. (1) Shock Protection
electromagnetic irradiated to the 2.0-2.7GHz: 1V/m
By twisting with the earthing wire, noise flowing from the power In order to prevent those who are unfamiliar with power facility, e.g.,
field AM modulation product. 80%AM modulation@1kHz
Immunity test in Power line: 2kV
supply wires can be relieved to the earthing. However, if a filter is an operator, from getting a shock, make sure to take the following
(0.24)
(0.39)
171.6 37.5 IEC61000-4-4 installed on the power supply wires, the wires and the earthing
(0.39)
228(8.98)
10
(2.05)
applied to the power Analog I/O: 1kV wire may not need to be twisted. (a) Store the GOT within the control panel locked, and allow only
52
(2.05)
noise*1
52
226(8.90) line and signal lines. Signal lines: 1kV those who are familiar with power facility to unlock the panel.
GT2705
288(11.34) AC power type 4.1.3 Noise filter (power supply line filter) (b) Build the structure in order that the power supply will be shut off
Power line (between line and
when the control panel is opened.
(0.39)
167(6.57) ground): 2kV The noise filter (power supply line filter) is a device effective to reduce
10 120(4.72) 10
117(4.61) Power line (between lines) (2) Dustproof and waterproof features
EN61131-2 conducted noise. Except some models, installation of a noise filter onto
6 139(5.47)
: 1kV The control panel also provides protection from dust, water and other
: 2007 Immunity test in Data communication port the power supply lines is not necessary. However conducted noise can
substances. Insufficient ingression protection may lower the
IEC61000-4-5 which lightening : 1kV be reduced if it is installed. (The noise filter is generally effective for
Surge immunity*1
insulation withstand voltage, resulting in insulation destruction.
surge is applied to DC power type reducing conducted noise in the band of 10MHz or less.) Usage of the
(0.39)
(0.24)
89 The insulation in the GOT is designed to cope with the pollution level
(3.50) the product. Power line (between line and following filters is recommended.
ground) : 0.5kV 2, so use in an environment with pollustion level 2 or better.
Unit : mm (inch) Power line (between lines) Model name FN343-3/05 FN660-6/06 RSHN-2003
152(5.98) : 0.5kV Pollution level 1: An environment where the air is dry and conductive
Manufacturer SCHAFFNER SCHAFFNER TDK dust does not exist.
Data communication port
Rated current 3A 6A 3A Pollution level 2: An environment where conductive dust does not
: 1kV
4. EMC AND LOW VOLTAGE DIRECTIVE IEC61000-4-6
Immunity test in
which a noise
Rated voltage 250V usually exist, but occasional temporary conductivity
occurs due to the accumulated dust.
Power line: 10V The precautions required when installing a noise filter are described
For electromagnetic compatibility (EMC) and electrical safety, regulatory Conducted RF inducted on the
Data communication port: 10V
Generally, this is the level for inside the control panel
standards are established in each country. immunity*1 power and signal below. equivalent a control room or on the floor of a typical
Especially, for the products to be sold in European countries,
lines is applied. (1) Do not install the input and output cables of the noise filter together to factory.
conformance to the EMC Directive, which is one of the European Test for checking prevent the output side noise will be inducted into the input side cable Pollution level 3: An environment where conductive dust exits and
normal operations
Directives, has been mandatory as the EMC standards since 1996. In where noise has been eliminated by the noise filer. conductivity may be generated due to the accumulated
under the
addition, conformance to the Low Voltage Directive, another European IEC61000-4-8 dust.
circumstance Input side
Directive, has also been mandatory as the electrical safety standards Power supply (power supply side)
Input side An environment for a typical factory floor.
exposed to the 30 A/m (power supply side)
since 1997. frequency magnetic
ferromagnetic field Pollution level 4: Continuous conductivity may occur due to rain, snow,
In European countries, if a product meets the requirements of the EMC field immunity
noise of the power etc. An outdoor environment.
Directive or the Low Voltage Directive, the product's manufacturer must supply frequency
declare conformity of the product and affix the CE mark to the product. In (50/60Hz). Induction 4.2.4 Grounding
some countries or regions other than European countries, the product's Filter Filter
IEC61000-4-11 AC power type The following are applicable ground terminals. Use them in the grounded
manufacturer also must declare conformity of the product and affix a Instantaneous
Test for checking
0.5 cycle 0% (interval 1 to 10s) Output side Output side
designated mark to the product (example: UKCA mark in the UK). power failure and
normal operations
250/300 cycle 0% (device side) (device side) state.
• Authorized representative in the EU and the UK voltage dips
at instantaneous
10/12 cycle 40% Be sure to ground the GOT for ensuring the safety and complying with
The authorized representative in the EU and the UK is shown below. immunity
power failure.
25/30 cycle 70% • Installing the input and output cables • Separate the input cable from the output the EMC Directive.
Name :Mitsubishi Electric Europe BV together will cause noise induction. cable. Functional grounding : Improves the noise resistance.
Address :Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany *1: The GOT is an open type device (device installed to another device) and must
(2) Connect the noise filter's ground terminal to the control panel with the
This section describes the EMC Directive and Low Voltage Directive as be installed in a conductive control panel.
examples for conformance to EMC and electrical safety standards. EMC The above test items are conducted in the condition where the GOT is installed shortest cable as possible (approx. 10cm (3.94 in.) or less).
and electrical safety standards in each country are stipulated to be on the conductive control panel and combined with the Mitsubishi Electric PLC. 4.2.5 External wiring
consistent with the corresponding international standards. When the *2: QP (Quasi-Peak): Quasi-peak value, Mean: Average value 4.2 Requirements for Compliance with the Low
(1) External devices
requirements are consistent with the same standards, common *3: The above test items are conducted in the following conditions.
measures are taken to conform to the standards in different countries. 30M-230MHz QP : 40dB V/m (10m in measurement range)
Voltage Directive When a device with a hazardous voltage circuit is externally
For the EMC Directive, regulatory compliance with equivalent EMC 230M-1000MHz QP : 47dB V/m (10m in measurement range) The Low Voltage Directive requires each device which operates with connected to the GOT, select a model which complies with the Low
standards are required for example in the UK and Korea. For the Low power supply ranging from 50VAC to 1000V and 75VDC to 1500V to Voltage Directive's requirements for isolation between the primary
Voltage Directive, regulatory compliance with equivalent electrical safety 4.1.2 Control panel satisfy necessary safety items. and secondary circuits.
standards are required for example in the UK. The GOT is an open type device (device installed to another device) and (2) Insulation requirements
In the Sections from 4.2.1 to 4.2.5, cautions on installation and wiring of
must be installed in a conductive control panel. the GOT to conform to the Low Voltage Directive requires are described. Dielectric withstand voltages are shown in the following table.
4.1 Requirements to Meet EMC Directive It not only assure the safety but also has a large effect to shut down the Reinforced Insulation Withstand Voltage
We have put the maximum effort to develop this material based on the
EMC Directives are those which require "any strong electromagnetic noise generated from GOT, on the control panel. requirements and standards of the Directive that we have collected. (Installation Category II, source : IEC664)
force is not output to the external.:Emission (electromagnetic (1) Control Panel However, compatibility of the devices which are fabricated according to Rated voltage of hazardous
interference)" and "It is not influenced by the electromagnetic wave from (a) The control panel must be conductive. the contents of this manual to the above Directive is not guaranteed. voltage area
Surge withstand voltage (1.2/50 s)
the external.: Immunity (electromagnetic sensitivity)". (b) When fixing a top or bottom plate of the control panel with bolts, Each manufacturer who fabricates such device should make the final 150 VAC or below 2500V
Items4.1.1 through4.1.3 summarize the precautions to use GOT and do not coat the plate and bolt surfaces so that they will come into judgement about the application method of the Low Voltage Directive
contact. 300 VAC or below 4000V
configure the mechanical unit in order to match the EMC directives. and the product compatibility.
Though the data described herein are produced with our best on the And connect the door and box using a thick grounding cable in
basis of the requirement items and standards of the restrictions gathered order to ensure the low impedance under high frequency. 4.2.1 Standard subject to GOT 5. INSTALLATION
by Mitsubishi Electric, they do not completely guaranteed that all (c) When using an inner plate to ensure electric conductivity with the
mechanical unit manufactured according to the data do not always control panel, do not coat the fixing bolt area of the inner plate Standard applied to GOT : EN61131-2 Programmable controllers - Equipment
5.2 Panel Cutting Dimensions Item GT2715 GT2712 GT2710 GT2708 GT2705 5.3 Position de montage 5.4 Température intérieure et angle
RGB output unit fitted*3 48(1.89) or more[18(0.71) or more] -
For GT2715-X 48(1.89) or 48(1.89) or 48(1.89) or Lors du montage du GOT, laissez les espaces suivants pour les autres d'installation du tableau de commande
C B C more more more 67(2.64) or structures et dispositifs.Certains câbles peuvent être plus longs que les Lors de l'installation du GOT sur un panneau, réglez la zone d'affichage
*Panel thickness : 1.6 to 4 mm Multimedia unit fitted*1 -
C A C [18(0.71) [38(1.50) [45(1.77) more dimensions spécifiées lors de la connexion au GOT.
(0.06 to 0.16 inch) comme indiqué ci-dessous.
C
A or more] or more] or more] Par conséquent, prenez également en compte les dimensions du
GOT A B Si l'angle d'installation est différent de celui indiqué, le GOT se détériore
C
C Printer unit fitted 48(1.89) or more[18(0.71) or more] connecteur et le rayon de courbure du câble pour l'installation.
GT 383.5 (15.10) 282.5 (11.12) External I/O unit fitted 48(1.89) or more[18(0.71) or more] Pour connaître l'espace à laisser pour les câbles sous le GOT, référez- plus tôt.
+2 (0.08) +2 (0.08)
A
B
2715 0 (0) 0 (0) Sound output unit fitted 48(1.89) or more[18(0.71) or more] vous au manuel GOT2000 Series User’s Manual (Hardware). Installation du GOT à l’horizontale
Horizontal: 78(3.07) or more[18(0.71) or more] Pour l’installation à la verticale, installez le GOT de sorte que la flèche Lors de l'installation du GOT avec un angle d'installation compris entre
GT 302 (11.89) 228 (8.98) B
Vertical: 48(1.89) or more[18(0.71) or more] d’installation à la verticale imprimée sur la face arrière du GOT pointe
C
+2 (0.08)
2712 0 (0)
+2 (0.08) 60 et 105°, la température à l'intérieur du tableau de commande doit
Horizontal 0 (0) 50(1.97) 100(3.94) vers le haut.
C
For specifications of the cable, refer to the GOT2000 Series Connection Manual
B
+2 (0.08) +2 (0.08)
2705 0 (0) 0 (0) de l’installation du GOT avec tout autre angle que 90°, la température
for a controller used.
A
C
Horizontal Vertical *3: This value differs depending on the cable used. Horizontal Épaisseur du panneau : Zone d'affichage Zone d'affichage
If the bending radius of the cable used is greater than the value specified 1,6 à 4mm(0,06 à 0,16 pouce) Vertical
above, apply the value of the cable used.
5.3 Mounting Position *4: When opening or closing the battery cover: 72(2.83) or more
Épaisseur du panneau : 1,6 à 4mm(0,06 à 0,16 pouce) GOT GOT
Laissez les espaces entre le GOT et les autres dispositifs en fonction 105° 90°
When mounting the GOT, the following clearances must be maintained
from other structures and devices.
5.4 Control Panel Inside Temperature and des dimensions contenues dans le tableau suivant. Les valeurs entre
parenthèses s'appliquent au cas où aucun dispositif générant des
Some cables may need to be longer than the specified dimensions when Installation Angle émissions sonores (comme un contacteur) ou de la chaleur n'est installé 60°
connecting to the GOT. When installing the GOT to a panel, set the display section as shown près du GOT.Toutefois, maintenez la température ambiante du GOT à
Therefore, consider the connector dimensions and bending radius of the below.Using the GOT with the installation angle other than the following 55°C ou moins. Tableau ou autres Tableau ou autres
cable as well for installation. deteriorates the GOT earlier. Unité: mm (pouce)
For the lead-in allowance for cables at the bottom of the GOT, refer to Installing the GOT horizontally Article GT2715 GT2712 GT2710 GT2708 GT2705
the GOT2000 Series User’s Manual (Hardware) . When installing the GOT with the installation angle between 60 to 48 (1,89) Horizontal Vertical
ou plus 59(2.32)
For the vertical installation, install the GOT so that the vertical installation 105 °, the temperature inside the control panel must be within 55°C. GOT uniquement 48 (1,89) ou plus[18 (0,71) ou plus]
[29 (1,14) ou plus
arrow printed on the GOT rear face points upward. When installing the GOT with the installation angle other than
between 60 to 105 °, the temperature inside the control panel must be
ou plus] 6. MAINTENANCE AND INSPECTION
Unité de communication
48 (1,89) ou plus[18 (0,71) ou plus]
within 40 °C. Ethernet encastrée Refer to the GOT2000 Series User’s Manual (Hardware) for
D Installing the GOT vertically 23 (0,91)
maintenance and inspection for the GOT.
B
When the GOT is installed a 90° angle, the control panel inside Unité de connexion de bus
48 (1,89) ou plus[18 (0,71) ou plus]
ou plus 48(1.89)
encastrée [29 (1,14) ou plus
temperature must be within 55°C. When the GOT is installed at any ou plus]
C D E B A angle other than 90°, the control panel inside temperature must be
E Unité de connexion série 47(1.85)
within 40°C. encastrée
48 (1,89) ou plus[18 (0,71) ou plus]
ou plus
Display section Display section 50(1.97)
A
to 55°C or lower.
5. INSTALLATION IE encastré
Module de communication
55(2.17)
Unit: mm(inch) réseau de champ CC-Link IE 48 (1,89) ou plus[18 (0,71) ou plus]
CC-Link IE Controller
55(2.17) or 10 Horizontal: 50 (1,97) ou plus[20 (0,79) ou plus]
D
Network communication 48(1.89) or more[18(0.71) or more]
more Vertical GT 289 (11,38) 200 (7,87) Vertical: 80 (3,15) ou plus[20 (0,79) ou plus] failsafe functions in the system.
unit fitted +2 (0,08) +2 (0,08) (0,39)
For GT27 (sauf GT2715-X) 2710 0 (0) 0 (0) E*4 100 (3,94) ou plus[20 (0,79) ou plus]
CC-Link IE Field Network 55(2.17) or ou plus
48(1.89) or more[18(0.71) or more]
A C B C
communication unit fitted more GT 227 (8,94) 176 (6,93) *1: Cette valeur est utilisée pour le câble coaxial 3C-2V (JIS C 3501).
48(1.89) or 48(1.89) or 48(1.89) or +2 (0,08) +2 (0,08)
Pour connaître les spécifications du câble, référez-vous au manuel GOT2000
C
2708 0 (0) 0 (0) HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
more more more 67(2.64) or
Video input unit fitted*1 - Series Connection Manual for a controller used. NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
[18(0.71) [38(1.50) [45(1.77) more GT 153 (6,02) 121 (4,76)
A