Professional Documents
Culture Documents
112-6440
41-1202-0192-0
Kodak PACS Link 9410 Acquisition System User Guide
Warnings and Cautions for PACS Link 9410 Acquisition System
2000 Rev. B i
! WARNING
This equipment is operated with hazardous voltage which can shock,
burn, or cause death.
Remove wall plug before servicing equipment. Never pull on cord to remove from
outlet. Grasp plug and pull to disconnect.
Do not operate equipment with a damaged power cord.
Do not use an extension cord to power this equipment.
Use only the power cord supplied with this equipment.
Position the power cord so it will not be tripped over or pulled.
Connect this equipment to a grounded outlet.
! WARNING
Not protected against ingress of liquids, including bodily fluids.
! WARNING
For continued protection against fire, replace fuses only with fuses of the same type
and fuse rating.
! CAUTION
This equipment is intended to connect to other medical devices. Installation and
service maintenance are to be performed only by qualified service personnel. The
equipment must be installed no closer than 1.83 meters from a patient bed or chair.
! CAUTION
Do not use in the presence of flammable anesthetics, oxygen or nitrous oxide. This
equipment does not have a gas sealed electronics enclosure and could ignite any
flammable or explosive gases present in its environment.
Kodak PACS Link 9410 Acquisition System User Guide
Warnings and Cautions for PACS Link 9410 Acquisition System
2000 Rev. B ii
! CAUTION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
! CAUTION
General External Cleaning: This equipment may be cleaned with a damp cloth
using water with mild detergent, or commercial electronic equipment cleaner.
! CAUTION
Do not substitute or modify any part of this equipment without approval of Eastman
Kodak Company.
Kodak PACS Link 9410 Acquisition System User Guide
Warnings and Cautions for PACS Link 9410 Acquisition System
2000 Rev. B iii
! CAUTION
Medical Equipment
UL 2601-1 CAN/CSA No. 601.1
!
Classified by Underwriters Laboratories Inc. With Respect to Electric
Shock, Fire, Casualty and Medical Hazards only in Accordance with UL 2601-1,
CAN/CSA C22.2 No. 601.1 and IEC 601.1.
! WARNING
This equipment is operated with hazardous voltage which can shock,
burn, or cause death.
Remove wall plug before servicing equipment. Never pull on cord to remove from
outlet. Grasp plug and pull to disconnect.
Do not operate equipment with a damaged power cord.
Do not use an extension cord to power this equipment.
Use only the power cord supplied with this equipment.
Position the power cord so it will not be tripped over or pulled.
Connect this equipment to a grounded outlet.
! WARNING
Not protected against ingress of liquids, including bodily fluids.
Kodak PACS Link 9410 Acquisition System User Guide
Warnings and Cautions for External Interface Box Accessories
2000 Rev. B v
! WARNING
For continued protection against fire, replace fuses only with fuses of the same
type and fuse rating.
! CAUTION
Do not use in the presence of flammable anesthetics, oxygen or nitrous oxide. This
equipment does not have a gas sealed electronics enclosure and could ignite any
flammable or explosive gases present in its environment.
! CAUTION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
! CAUTION
Do not substitute or modify any part of this equipment without approval of Eastman
Kodak Company.
! CAUTION
General External Cleaning: This equipment may be cleaned with a damp cloth
using water with mild detergent, or commercial electronic equipment cleaner.
Audience
The primary audience for this User Guide is the key operator or the system
administrator for the PACS Link 9410 Acquisition System and related Kodak Laser
Imagers and imaging devices.
Packaging
This user guide is packaged with the CD-ROM disks and miscellaneous information
sheets supplied with the PACS Link 9410 Acquisition System.
Emissions
The PACS Link 9410 Acquisition System has passed RFI Emissions Testing. It was
found that the PACS Link 9410 Acquisition System does not add to the emissions
of the Dell computer supplied as part of this product. Therefore the PACS Link
9410 Acquisition System meets the same emissions standards as the Dell
computer.
Refer to the Reference and Installation Guide supplied with the Dell computer for
more information on the RFI emissions standards and regulations that apply to the
Dell computer.
Kodak PACS Link 9410 Acquisition System User Guide
Section 1 – Introduction
2000 Rev. B 1-1
Introduction
Product Overview
The PACS Link 9410 Acquisition System is a flexible, modular system for capturing
images from a variety of imaging modalities or network image sources. The
captured images can be printed on film, using a Kodak Laser Imager, or sent over a
network to remote printers or other destination devices connected to a network.
The PACS Link 9410 Acquisition System can connect to an Ethernet network and
uses the DICOM 3.0 protocol to send or receive images over the network.
There are three versions of the PACS Link 9410 Acquisition System:
1. Print Server version
Connects to an Ethernet network. Receives images from DICOM-compliant
modalities or other DICOM devices on the network and forwards these images
to a Kodak Laser Imager for printing on film.
Refer to Section 2 in this manual for more detailed information on the Print
Server.
2. Modality Server version
Captures images from up to three connected modalities. An operator can route
these images to:
A Kodak Laser Imager for printing on film.
Remote printers or other DICOM-compliant 3.0 print class devices on an
Ethernet network.
Refer to Sections 3 through 7 in this manual for more detailed information on the
Modality Server
3. Combination Print Server/Modality Server
This version of the PACS Link 9410 Acquisition System combines the functions
of both a Print Server and Modality Server. All of the information in this manual
for the individual Print Server and Modality Server versions apply to the
combination version.
Kodak PACS Link 9410 Acquisition System User Guide
Section 1 – Introduction
2000 Rev. B 1-2
Special Terms
The following terms are used throughout this User Guide.
Acquire
The act of capturing an image in electronic form from a modality.
Film
A single sheet of media that is produced when a print command is issued from the
keypad or from the user host control. A single film can display one or multiple
images, depending on the format selected and the number of acquisitions
performed.
DICOM
DICOM is a standard (set of rules) for the transfer of medical images between
various electronic medical devices such as image source modalities, viewing
stations, archiving stations etc. The PACS Link 9410 Acquisition System uses the
DICOM version 3.0 standard to exchange images with other DICOM-compliant
devices across an Ethernet network.
Host Control
A method of controlling the PACS Link 9410 Acquisition System from a modality. A
keyboard, control panel, touch screen or other control device that is part of a
modality is used to control image acquisition, printing and other PACS Link 9410
functions. Host control can be used in place of a Kodak-supplied keypad.
Image
An image is the resultant data, print or display obtained after an acquisition. Multiple
images can be printed on one film, depending on the format selected and the
number of acquisitions performed.
Modality
A medical imaging device such as a CT scanner, MRI or ultrasound imager that
provides an image output in electronic form.
MRN (Not Supported)
A patient’s medical record number.
Kodak PACS Link 9410 Acquisition System User Guide
Section 1 – Introduction
2000 Rev. B 1-3
Page
An image or a set of images printed on a single sheet of media.
Study (Not Supported)
A set of pages usually associated with a common medical imaging procedure for a
single patient.
Kodak PACS Link 9410 Acquisition System User Guide
Section 2 – Product Description – Print Server
2000 Rev. B 2-1
Image Input
Î Fiber or
Copper
from DICOM
Network
MIS-502L
Floppy Disk
Drive
CD–ROM
Drive
Floppy Disk
Eject Button
CD–ROM
Eject Button
Power
Switch/Indicator
Reset Button
Note
When installed, the PACS Link 9410 Acquisition System components were
placed flat, bottom-side down, on a tabletop or other sturdy base allowing for
easy service accessibility. In addition, precaution was taken during installation
to place the workstation so that it was not located in an area within ten feet of
the vicinity of patient care. The vicinity of patient care is defined as any area
accessible by the patient or by those administering care that can touch the
patient. Because of these precautions, it is recommended that relocation or
movement of the PACS Link 9410 Acquisition System be performed only by
Kodak personnel or their designated representatives.
Aside from turning power on or off there are no actions that must be performed by
an operator on the Print Server.
System Power Up
To turn Print Server power ON or OFF press the power switch on the front of the
Workstation case. The power indicator lights up when power is ON. After you turn
on power, the Print Server performs a start–up sequence that takes about three
minutes. It is then ready to receive and print images.
The Kodak Print Server is designed to run 24 hours a day, seven days a week. If
there is a power interruption, the Print Server should power up automatically with no
operator assistance when power is restored.
Kodak PACS Link 9410 Acquisition System User Guide
Section 2 – Product Description – Print Server
2000 Rev. B 2-6
Lost Images
Sometimes a failure occurs during transmission of images and the major concern is:
Are my images lost? Use Table 2-2 to determine the possible location of images
when a problem has occurred and the required corrective action.
Table 2-2. If a Problem Occurs, Are My Images Lost?
Problem Action
If there is a problem with the Laser Imager and it Correct Laser Imager problem.
occurs during or after the network transmission The Print Server will then
to the Print Server, the images will remain automatically send stored
stored on the Print Server hard disk. images to the Laser Imager.
If there is a problem with the Laser Imager and it Correct Laser Imager problem.
occurs after the Print Server sends an image to The image may have to be
the Laser Imager, the image may become lost if recaptured at the DICOM
power is disconnected from the Laser Imager. image source device.
If a problem in the Print Server prevents it from Correct Print Server problem
capturing images from the network, the images and resubmit images from
remain in the DICOM image source device. DICOM image source device.
If a problem occurs with the DICOM image Correct problem at the DICOM
source device, images will have to be image source device and
recaptured. recapture images.
Modalities
(Image Sources)
PACS Link 9410
Acquisition System
(Modality Server Version)
Î Fiber or
Copper
Output to
DICOM / Ethernet
Digital or Video Network
Connections
MIS–503L
Networked System
Two or more PACS Link 9410 Acquisition Systems are often linked together along
with other DICOM-compliant devices on a common Ethernet network. Figure 3-2
shows a typical networked system. In this system images can be routed from
Modality Servers across the network to a Print Server or to a Kodak Laser Imager
for printing on film.
Kodak PACS Link 9410 Acquisition System User Guide
Section 3 – Product Description – Modality Server
2000 Rev. B 3-5
Kodak HQ
NucMed/MRI Department Laser Imager
Modality
Server
1
Î Print
ÎÎ
Server 2
Digital or Video
Connections ethernet
Ultrasound Department (10baseT)
DryView 8300
Laser Imager
Modality
Server 1
Î
Î Fiber or
Copper
DryView 8700
Laser Imager
PACS Host
Functions Link 9410 Control
Keypad
Format Select yes yes
Multiple Copy Adjustment yes yes
Sequential Image Acquire yes yes
Random Image Acquire yes yes
Sequential Image Erase yes yes
Random Image Erase yes yes
Move Acquired Image yes no
Print yes yes
Stop Print yes yes
Density Adjustment yes yes
Contrast Adjustment yes yes
Print Density Test yes yes
Print Contrast Test no yes
Smooth/Sharp Select yes yes
Image Polarity Select yes yes
Auto-Print Select yes yes
Auto-Format Select yes yes
Alarm Volume Adjustment yes yes
Media Size Select yes yes
Re-Print Capability no no
Medical Record Number Select no no
Destination Select yes no
Abort Print yes yes
Requeue Print no no
Study Labeling no no
Print Batching yes no
Print Priority yes no
Kodak PACS Link 9410 Acquisition System User Guide
Section 4 – Controls and Indicators
2000 Rev. B 4-1
Floppy Disk
Drive
CD-ROM
Drive
Floppy Disk
Eject Button
CD-ROM
Eject Button
Power
Switch/Indicator
Reset Button
1 Boxes
5 Erase Print 2
3 Buttons
4
MIS-489L
Main Menu
The numbered descriptions below correspond to Figure 4-3.
1. The Attention Message box displays name, system status, and error messages
for the currently selected image destination.
2. The Selected Laser Imager box identifies which laser imager is currently
selected and it displays the amount of free memory in the input module.
3. The Media box displays media information for the currently selected laser
imager.
4. The Copies arrows select the number of copies to print. When a study is open,
these arrows are not visible because the number of copies cannot be changed.
5. The Stop Print box stops the print function.
6. The Imager Menu box selects the image destination and image parameter
setup for that destination.
7. The Format Menu box selects the output format. When the Erase Button is
pushed, this box changes to an Erase All Images box. (Refer to page NO TAG.)
8. The Keypad Menu box changes the brightness, alarm, and beep feature of the
keypad.
9. The Study Setup Menu is not supported.
Kodak PACS Link 9410 Acquisition System User Guide
Section 4 – Controls and Indicators
2000 Rev. B 4-5
Main Menu
Laser Imager “Kodak laser - Fp1”
Status:
Ready 1
Media: 14 X 17
Supply: 125
9 Queued: 10 3
Printed: 1231
Erase Print
Keypad Menu
This menu is accessed from the Main Menu as follows:
. Main Menu
. Keypad Menu
The Keypad Menu changes the default settings for the keypad.
The numbered descriptions below correspond to Figure 4-4.
1. The Attention Message box displays name, system status, and error messages
for the currently selected laser imager.
2. The Display Brightness arrows set the keypad display brightness.
3. The Alarm Beep Volume arrows set the keypad alarm volume.
4. The Auto Print box toggles between ON or OFF. When set to ON, a print is
automatically queued after the last image is stored (the Print button does not
have to be pressed).
5. The Auto Format box toggles between ON and OFF. If ON, stored images are
automatically erased from memory after print; thereby, preparing the system for
new acquisition entries. If OFF, stored images remain in memory after print and
must be erased manually before new acquisitions may be made.
6. The Key Beep Volume arrows set the key beep volume.
7. The Color Blind Mode box toggles between ON or OFF. When set to ON, the
red LEDs above the Store buttons (which indicate used storage locations) blink
instead of staying on constantly. This allows a color blind operator to
differentiate the red LEDs from the green LEDs constant on (which indicate
available storage locations).
Note
When in Erase Image mode, the red LEDs blink regardless of whether the
color blind feature is ON or OFF.
Keypad Menu
Laser Imager “Kodak laser - Fp1”
Status:
Ready 1
Color
Blind
7 Mode Display
OFF Brightness
6 3
Auto Auto
Format Print RETURN
5 8
OFF OFF
Erase
4
Figure 4-4. Keypad Menu
Kodak PACS Link 9410 Acquisition System User Guide
Section 4 – Controls and Indicators
2000 Rev. B 4-8
Format Menu
This menu is accessed from the Main Menu as follows:
. Main Menu
. Format Menu
The Format Menu, shown in Figure 4-5, chooses the output format.
The numbered descriptions below correspond to Figure 4-5.
1. The Attention Message box displays name, system status, and error messages
for the currently selected laser imager.
2. The Format Select boxes designate how many images are to be printed on one
sheet of media.
3. The Media Size box designates the size of media.
4. The Cancel box returns to the Main Menu without selecting an output format.
Format Menu
Laser Imager “Kodak laser -
FP1” 1
Status:
Ready
1 2 4 6
9 12 15 16
Media 3
20 Size Cancel
Menu 4
Note
Available media size selections vary with the type of laser imager selected.
Kodak PACS Link 9410 Acquisition System User Guide
Section 4 – Controls and Indicators
2000 Rev. B 4-10
14 x 17 11 x 14 8 x 10
2, 3, 4
RETURN 5
Imager Menu
This menu is accessed from the Main Menu as follows:
. Main Menu
. Imager Menu
The Imager Menu lets you change the default settings for the selected imager.
The numbered descriptions below correspond to Figure 4-7.
1. The Attention Message box displays name, system status, and error messages
for the currently selected laser imager.
2. The Contrast, Density, & Count Menu box displays a menu used to select the
contrast table, adjust density/Dmax, and reset print count for the selected
imager.
3. The Print Density Test box prints a density test film on the selected imager.
4. The Image Polarity box toggles between POSITIVE and NEGATIVE.
5. The Media Borders box toggles between CLEAR and DARK borders. Most
users prefer dark borders.
6. The Destination Selection Menu box displays a menu used to select the laser
imager, network printer or other network destination that will receive images
from the PACS Link 9410 Acquisition System.
7. The Image Rotation box toggles between ON and OFF. Select ON to rotate the
image 90 degrees. This box only appears on laser imagers that support this
feature.
8. The Image Processing box toggles between SMOOTH and SHARP.
9. The Image Framing box toggles between ON and OFF. Select ON for a narrow
frame around the output image.
10. The Print Contrast Test box is not supported.
11. The Abort Menu box displays a menu used to abort queued print jobs that have
not started printing.
12. The RETURN box returns to the Main Menu.
Kodak PACS Link 9410 Acquisition System User Guide
Section 4 – Controls and Indicators
2000 Rev. B 4-12
Imager Menu
Laser Imager “Kodak laser - Fp1”
Status:
Ready 1
Abort Contrast,
Menu Density,
11 & Count 2
Menu
Destination Media
Selection Borders RETURN 12
6 Menu
DARK 5
Contrast/Density/Count Menu
K190: Changing the contrast and/or
density will affect image quality.
1
Reset
Printed
Count 2
Contrast 8 Density 10
4 3
RETURN
5
Erase Print
No Printer
Imager DEF
969
2
2 of 6
Imager XYZ
8700 3
Main Menu
- Copies Count Selection Arrows
- Close Study
- Erase Button
- Print Button
Imager Menu Study Setup Menu (Not supported) Keypad Menu Format Menu Open Study Menu (Not supported)
Abort Menu Color Blind Mode (Not available while aquiring images)
- 14x17 Media Size
- 11x14 Display Brightness Arrows (Varies with selected printer)
- 8x10 Key Beep Volume Arrows - 14x17
- Abort Alarm Beep Volume Arrows - 11x14
- All Sizes - 8x10
Auto Format - Return
- Return
Contrast, Density, Count Menu - OFF Format Select
OK - ON (Varies with selected printer)
- Reset Printed Count Auto Print -1
- Density / DMAX Arrows - OFF -2
- Contrast Arrows - ON -4
- Return Return -6
Requeue Menu (Not Supported) -9
Print Contrast Test (Not supported) - 12
Image Framing - 15
- OFF - 20
- ON Cancel
Print Density Test
Image Processing
- SMOOTH
- SHARP
Image Rotation
(Not available on all printers)
Image Polarity
- POSITIVE
- NEGATIVE
Destination Selection Menu
- Selection Arrows
- Imager Selection(s)
- Return
Media Borders
(Not available on all printers)
- DARK
- CLEAR
Return
Kodak PACS Link 9410 Acquisition System User Guide
Section 5 – Operation and Maintenance
2000 Rev. B 5-1
Note
When installed, the PACS Link 9410 Acquisition System components were
placed flat, bottom-side down, on a tabletop or other sturdy base allowing for
easy service accessibility. In addition, precaution was taken during installation
to place the workstation so that it was not located in an area within ten feet of
the vicinity of patient care. The vicinity of patient care is defined as any area
accessible by the patient or by those administering care that can touch the
patient. Because of these precautions, it is recommended that relocation or
movement of the PACS Link 9410 Acquisition System be performed only by
Kodak personnel or their designated representatives.
System Power Up
To turn Modality Server power ON or OFF, press the power switch on the front of the
Workstation case. The power indicator lights up when power is ON. After you turn
on power, the Modality Server performs a startup sequence that takes about three
minutes. The optional PACS Link 9410 Keypads or Host keypads will indicate ready
when the startup sequence is complete.
Several types of external interface boxes (called EIBs) are used to connect
keypads, host control devices and modalities to the Modality Server. These interface
boxes should be powered ON before the Modality Server is powered ON.
The Kodak Modality Server is designed to run 24 hours a day, seven days a week. If
there is a power interruption, the Modality Server should power up automatically
with no operator assistance when power is restored.
Kodak PACS Link 9410 Acquisition System User Guide
Section 5 – Operation and Maintenance
2000 Rev. B 5-2
Density/Contrast Selection
1. Display an image on the appropriate user’s console.
2. Adjust the console window and level controls to achieve the desired image
quality on the display monitor.
3. Press the Format Menu box on the Main Menu, then press any Format Select
box on the Format Menu.
4. Press any green lighted Store button or the Sequential Store button to acquire
the image. (See Figure 4-2.)
5. Press the Imager Menu box on the Main Menu.
6. Press the Print Contrast Test box. The imager prints the acquired image in a
15:1 format on a single sheet, using each of the 15 different contrast table
settings.
7. Examine the test sheet to determine if the maximum density is acceptable.
If the maximum density is acceptable, go to to Step 11.
If the maximum density is not acceptable, continue with Step 8.
8. Press the Contrast, Density, & Count Menu box on the Imager Menu, then
press the OK box.
9. Press the Density arrows as required to change the density setting. When the
desired density value is displayed, press the RETURN box.
10. Repeat Steps 6 through 9 until the desired maximum density is achieved.
11. Examine the 15 images on the contrast test sheet. Select the image with the
most appropriate contrast.
12. Press the Contrast, Density, & Count Menu box on the Imager Menu, then
press the OK box.
Kodak PACS Link 9410 Acquisition System User Guide
Section 5 – Operation and Maintenance
2000 Rev. B 5-3
13. Press the Contrast Set arrows as required to change the contrast table settings
to the value printed next to the selected image. Press the RETURN box when
the desired contrast value is displayed.
14. Press the RETURN box on the Imager Menu to return to the Main Menu.
Note
If the auto print function is ON, a print request is automatically placed in the
print queue when the last image in the format is stored.
5. At this point, a new format can be selected and/or more images acquired and
stored.
If the auto format function is ON, a new format is automatically displayed,
allowing more images to be acquired.
If the auto format function is OFF, new images cannot be acquired until a
new format is selected or the currently stored images are erased using the
Erase Image function.
Note
In Erase Image mode, at the Main Menu, the Erase All Images box is
displayed in place of the Format Menu box.
3. To erase all stored images, press the Erase All Images box on the Main Menu.
After erasing all the stored images, the keypad automatically exits the Erase
Image mode.
Kodak PACS Link 9410 Acquisition System User Guide
Section 6 – Troubleshooting
2000 Rev. B 6-1
Troubleshooting
Message
Number Keypad Message Operator Action
K58 The images are too large for the Select a format with fewer
format. images.
K59 Image signal error. Try acquiring Self-explanatory.
K64 again.
K65 Image acquire failed. Try acquiring Self-explanatory.
K66 again.
K68
K72 Memory error. Try acquiring again. Self-explanatory.
K73 Memory error during printing. Refer to the panel on the imager.
K85 Image memory is full. Wait for some images to be
printed. This frees some image
memory and allows more images
to be acquired. The percentage of
free memory is listed on the Main
Menu.
K177 Images must be printed or erased Self-explanatory.
before the format can be changed.
K178 Print jobs stopped. A calibration print Self-explanatory.
must be performed for these jobs to
complete.
K179 The Frame feature is not available Informational message; no action
on the selected imager. needed.
K180 The Rotation feature is not available Informational message; no action
on the selected imager. needed.
K183 The keypad has a stuck key or the Check for objects laying on the
foot switch is stuck. keypad or foot switch.
K184 The touch screen is disconnected or Call for service.
damaged.
K185 Print jobs stopped. Load the correct Self-explanatory.
media type.
K186 Image contrast has been preset by Informational message. If an
custom format. g processing
image g parameter has
K187 Image polarity has been preset by been preset as part of a custom
custom format. format byy your
y administrator, that
K188 Image processing has been preset parameter
t setting
tti cannott be
b
by custom format. changed at the keypad.
Kodak PACS Link 9410 Acquisition System User Guide
Section 6 – Troubleshooting
2000 Rev. B 6-3
Message
Number Keypad Message Operator Action
K189 Image framing has been preset by
custom format.
–– No destination selected. Select destination via the Imager
Menu.
K190 Changing the contrast and/or density Informational message displayed
will affect image quality. to discourage unnecessary
changes to the contrast and
density settings.
K191 Move image to an unacquired image Informational message displayed
location. To Cancel: Press any when the Move function is
acquired image. enabled.
K192 Internal keypad error. Reset contrast Self-explanatory.
and density settings.
K193 An image must be acquired before Self-explanatory.
selecting contrast test.
K194 Image aspect ratio changed. Informational message. Indicates
that an image’s aspect ratio was
changed when the image was
reduced to fit the selected format.
K195 Format select failed. Try again. Self-explanatory.
K198 Queuing print. Please wait. Self-explanatory.
K199 Setting up format. Please wait. Informational message; no action
needed.
K200 Laser imager 1 self test in progress. Informational message; no action
needed.
K202 Laser imager x is not operational. Refer to the panel on the imager.
K203 The local panel is bad on laser Call for service.
imager x.
K204 The media is low on laser imager x. Self-explanatory.
K206 Load the correct media type. The loaded media does not match
the media size selected from the
Media Size menu. Load the
correct size media.
K209 Problem with supply cartridge on Refer to the panel on the imager.
laser imager x.
K210 Printer error. Check local panel on Refer to the panel on the imager.
laser imager x.
Kodak PACS Link 9410 Acquisition System User Guide
Section 6 – Troubleshooting
2000 Rev. B 6-4
Message
Number Keypad Message Operator Action
K211 Media is jammed in laser imager x. Refer to the panel on the imager.
Check local panel.
K215 A cover is open on laser imager x. Refer to the panel on the imager.
K216 The receive magazine is missing on Install an empty receive magazine
laser imager x. in the laser imager.
K217 Empty the receive magazine on Self-explanatory.
laser imager x.
K218 Supply cartridge is empty on laser Load a non-empty supply
imager x. cartridge.
K221 Processor x is not functional. Refer to the panel on the imager.
K222 Processor x is not ready. Minutes to Informational message; no action
ready: TTT. needed.
K227 Media is jammed in processor x. Remove the jammed piece of
Please remove the media. media from the imager following
the instructions in the Operator’s
Manual for the imager.
K228 A chemistry tank on processor x is Informational message; no action
low. needed.
K229 A chemistry tank on processor x is Fill the tank following the
empty. instructions in the Operator’s
Manual for the imager.
K230 System operating near calibration Check the system processor
limits. Check chemistry. chemistry. If the chemistry is OK,
try using a new supply cartridge.
K231 Processor warning. Check local Refer to panel on imager.
panel on laser imager x.
Kodak PACS Link 9410 Acquisition System User Guide
Section 6 – Troubleshooting
2000 Rev. B 6-5
CD-ROM
Eject Button
Specifications