Professional Documents
Culture Documents
-
W
I-
UDC 744.4 : 693.554 Ref. No. I S 0 4066-1977 (E)
l-
8
Descriptors : architecture, buildings, engineering drawings, reinforcing bars, codes, reinforcing bar schedule.
d
a Price based on 7 pages
FOR EWOR D
I S 0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 member bodies). The work of developing
International Standards is carried out through I S 0 technical committees. Every
member body interested in a subject for which a technical committee has been set
up has the right t o be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Germany
Netherlands
South Africa, Rep. of
Printed in Switzerland
INTERNATIONAL STANDARD I S 0 4066-1977 (E)
As the use of preferred shapes is considered to be very Steel fabric and prestressing steel reinforcement are
excluded.
0 advantageous both for simplifying design and manufacture
and for the use of computers, the opportunity has been
taken to include a l i s t of preferred shapes and a coding
system; the layout of the bar schedule i s based on the use 3 METHODS OF INDICATING BENDING DIMENSIONS
of preferred shapes. The bending dimensions shall be indicated as shown in
figures 1 to 5.
1 SCOPE Dimensions shall be outside dimensions, except for radii,
This International Standard establishes a system for the and the standard radius of bend shall be the smallest radius
scheduling of reinforcing bars, and comprises permitted by national standards or regulations.
- the method of indicating dimensions; The total length (cutting length) shall be calculated on the
basis of the appropriate bending dimensions with corrections
- a coding system for bar shapes; for bends and allowances for anchorages.
1
IS0 4066-1977
BENDING DIMENSIONS
FIGURE 1 FIGURE 2
FIGURE 3 FIGURE 4
a(final diameter)
FIGURE 5
I S 0 4066-1977 {E)
The shape code number consists of two or, if essential, three or four characters, as defined in table 1.
O - No bends (optional) O - Straight bars (optional) O - No end anchorage (optional) S - Where a national standard
specifies a special radius of
1 - 1 bend 1 - 90' bendk) of standard 1- End anchorage a t one end, bend (for example stirrups,
radius all bent in the same as defined in national links) this shall be indicated
2 - 2 bends direction standards by use of the character S.
e
NOTE - This table explains the logic behind the numbering of the shapes in table 2. It is not to be used for making up codes for additional
shapes.
5 LIST OF PREFERRED SHAPES It i s recognized that in some countries hooks are used for
end anchorages.
When a third character i s used, the direction of the end
anchorages shall be as shown by the dotted lines in the The (etter symbols refer to the dimensions which shall be
examples in table 2. given in the bar schedule.
3
I S 0 4066-1977 (E)
-
code
O0
11
-I
12
15
I
1- -1
21 1 b J f
I
25
-
x* I r
26
-
4
I S 0 4066-1977 (E)
- TAB LE 2 (concluded)
Shapt
Shapes Examples
31
33
-
41
-
iTeh STANDARD PREVIEW
(standards.iteh.ai)
n
ISO 4066:1977
44 U
-
https://standards.iteh.ai/catalog/standards/sist/96c719e3-49c2-422b-88c7-
c7ec10fe1cef/iso-4066-1977
46
51
O
a
67
-
-
77 c : number of complete turns
o
5
IS0 4066-1977 (E)
The bar schedule i s the document used to specify and When special shapes are required, these shall be shown by a
identify reinforcing bars. The format specified below incor- dimensioned sketch drawn in the space normally used for
porates the use of preferred shapes. bending dimensions.
6
-I
.-CO b
.-n:!c
$ 2
U
t
*
8
O E
U Y-
??
.-O
E -I1m
,
.-
E P.c
W O P
.- L
0)
m"
E
m
.4
I iJ
e n
I
ISO 4066:1977
https://standards.iteh.ai/catalog/standards/sist/96c719e3-49c2-422b-88c7-
c7ec10fe1cef/iso-4066-1977
8
w
-I
k
t
$
:f
Lt;
I-
0
5
.-
5
z