Professional Documents
Culture Documents
-HUPHQVNLSRJRQL2ELþDMQLLQR]NLNOLQDVWLMHUPHQL'ROåLQHYRVQRYQHPVLVWHPX
ICS:
21.220.10 Jermenski pogoni in njihovi Belt drives and their
deli components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST ISO 4184:1997
INTERNATIONAL ISO
STANDARD 4184
Second edition
1992-12-15
(standards.iteh.ai)
SIST ISO 4184:1997
https://standards.iteh.ai/catalog/standards/sist/5e1e0113-0028-4264-90b6-
20002af8dcfc/sist-iso-4184-1997
Reference number
ISO 4184:1992(E)
SIST ISO 4184:1997
ISO 4184:1992(E)
Foreword
0 ISO 1992
All rights reserved. No part of this publication may be reproduced or utilized in any form or
by any means, electronie or mechanical, including photocopying and microfilm, without per-
mission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 l Switzerland
Printed in Switzerland
SIST ISO 4184:1997
1 Scope
iTeh STANDARDThePREVIEW V-belts of sections Y, Z, A, B, C, D, E are called
classical V-belts and those of sections SPZ, SPA, SPB
This International Standard
(standards.iteh.ai)
specifies, for classical and and SPC are called narrow V-belts.
narrow V-belts of sections lt is important that narrow belts are not used with
SIST ISO 4184:1997
Y (for groove Profile with datum width pulleys uniquely designed for classical belts.
https://standards.iteh.ai/catalog/standards/sist/5e1e0113-0028-4264-90b6-
53 m-n), 20002af8dcfc/sist-iso-4184-1997
Z (for groove Profile with datum width
83 mm),
2 Normative references
A (for groove Profile with datum width 11 mm),
The following Standards contain provisions which,
B (for groove Profile with datum width 14 mm), through reference in this text, constitute provisions
of this International Standard. At the time of publi-
C (for groove Profile with datum width 19 mm),
cation, the editions indicated were valid. All Standards
D (for groove Profile with datum width 27 mm), are subject to revision, and Parties to agreements
based on this International Standard are encouraged
E (for groove Profile with datum width 32 mm), to investigate the possibility of applying the most re-
cent editions of the Standards indicated below.
SPZ (for groove Profile with datum width Members of IEC and ISO maintain registers of cur-
83 rm), rently valid International Standards.
SPA (for groove Profile with datum width 11 mm),
ISO 3:1973, Preferred numbers - Series of preferred
SPB (for groove Profile with datum width 14 mm), numbers.
SPC (for groove Profile with datum width 19 mm): ISO 1081: 1980, Drives using V-belts and grooved
pulleys - Terminology.
- the recommended datum lengths;
ISO 4183:1989, Belt drives - Classical and narrow
- the tolerantes for datum lengths; V-belts - Grooved pulleys (System based on datum
width).
- the centre distance variations;
ISO 9608: 1988, V-belts - Uniformity of belts -
- the conditions for measuring the datum length and Cen tre dis tance Variation - Specifica tions and test
the centre distance Variation. me thod.
1
SIST ISO 4184:1997
ISO 4184:1992(E)
3 Definitions
I Distribution according
sections
ons
to the
Ld
SPZ SPA SPB SPC
4.1 The Standard datum lengths are the datum
lengths under tension measured under the conditions
630
specified in 7.1.
710 + +
800 +
900 +
1 000 +
4.2 The nominal values of the Standard datum
lengths of V-belts, expressed in millimetres, have 1 120 +
been selected from the R 20 series of preferred 1 250 +
numbers, in accordance with ISO 3. iTeh STANDARD PREVIEW 1 400 +
(standards.iteh.ai)
a) Classical V-belts - Sections Y, 2, A, B, C, D, E
1 600 +
1 800 +
Datum lengths of V-belts of section Y are givenSIST in ISO 4184:19972 000 +
table A.1 . https://standards.iteh.ai/catalog/standards/sist/5e1e0113-0028-4264-90b6-
2 240 +
20002af8dcfc/sist-iso-4184-1997
2 500 +
Datum lengths of V-belts of sections Z, A, B, C, D
and E, corresponding to the R 20 series of pre- 2 800 +
ferred numbers, are only applicable if the stock of 3150 +
moulds of the manufacturer conforms to this se-
3 550 +
ries. Otherwise, the datum lengths of these V-
belts shall be those given in table A.1. 4000
4 500
b Narrow V-belts - Sections SPZ, SPA, SPB, 5 000
SPC
5 600
Standard datum lengths of V-belts of narrow 6 300
sections SPZ, SPA, SPB and SPC are given in 7100
table 1.
8 000
9 000
10 000
11 200
12 500
5 Tolerantes on datum lengths
2
SIST ISO 4184:1997
ISO 4184:1992(E)
+lO
315<L&400 -5
The tolerantes of the narrow V-belts of sections SPZ,
SPA, SPB and SPC are approximately
+11
400<L,< 500 -6
+
- 0,OlL
+13
500<L& 630 -6 +6 where L is the preferred number in the R 10 series,
in accordance with ISO 3, equal to or immediately
630<Ld< 800 +15
-7 f8 greater than the length datum expressed in milli-
metres.
250
1 ooo<L,< 1
iTeh STANDARD
+19
-1013 PREVIEW *
3 150<r,~4000 +44
-22 * 40
Table 3 - Belt matthing tolerantes
Dimensions and tolerantes in millimetres
4 ooo<L& 5 000 +52
-26 rf: 50
Maximum permissible
deviation between the
5 ooo<L,< 6 300 Nominal datum length
+63
-32 k 63 lengths of belts of the
same set for sections
6 300<&-,< 8 000 +77
-38 zt 80 Y, Z A B, SPZ, SPA,
Ld
Cr D, E SPB, SPC
3
SIST ISO 4184:1997
ISO 4184:1992(E)