Professional Documents
Culture Documents
1. This is used for griping, holding, cutting electrical wires and cables and
even small nails. Usually used by linemen in doing heavy tasks.
A. Combination Pliers C. Wire Stripper
B. Long Nose Pliers D. Electrician’s Knife
2. Used for cutting and holding fine wires. This can reach tight space or
small opening where other pliers cannot reach and also used in making
terminal loops of copper wires.
A. Combination Pliers C. Wire Stripper
B. Long Nose Pliers D. Electrician’s Knife
8. This has a cross tip resembling a positive (+) sign. It is used to drive
screws with cross slot heads.
A. Stubby Screw Driver C. Philips Screw Driver
B. Connectors D. Circuit Breaker
PLACER NATIONAL HIGH SCHOOL Document Type: PNHS-EXAM
Magsaysay, Placer, Surigao del Norte Revision No.: 00
School ID: 304837 Effective Date 01 October 2022
Email: 304837@deped.gov.ph Page No. 2 of 6
10. A tool used for removing insulation of medium sized wires ranging from
gauge #10 to gauge #16.
11. A small drilling machine with a chuck capacity of ¼" to 3/8". It is used
in making holes on metal sheets and concrete walls.
A. Philips Screw Driver C. Wire Stripper
B. Portable Electric Drill D. Philips Screw Drive
12. The same application is done as in plain tap and the only difference is
that this tap is a combination of two plain taps place side by side with each
other.
A. Cross joint C. Aerial tap
B. Duplex cross joint D. Y-splice
13. a two-tap wire turned simultaneously and is used where the two-tap
wire is under heavy tensile stress.
A. Cross joint C. Aerial tap
B. Duplex cross joint D. Y-splice
14. This method of wrapping is generally used on small cables because the
strands are flexible and all can be wrapped in one operation.
A. Cross joint C. Aerial tap
B. Duplex cross joint D. Y-splice
15. Comes in either Standard or Philips screw driver with short shank or
blade and shorted handle used to turn screws in tight space where standard
screw driver cannot be used.
A. Philips Screw Driver C. Circuit Breaker
B. Connectors D. Stubby Screw Driver
16. Used by linemen to remove insulation of wire and cables in low and high
voltage transmission lines.
A. Electrician knife C. Circuit Breaker
B. Connectors D. Stubby Screw Driver
18. This is a circuit protective device that automatically blows and cut the
current when an over load or short circuit happens.
A. Fuse C. Male plug
B. Connectors D. Circuit Breaker
19. An instrument used to measure the amount of electrical current
intensity in a circuit.
A. Voltmeter C. Micrometer
B. Ammeter D. Ohmmeter
20. A pocket-sized tool used to test the presence of current in a line wire or
circuit.
A. Test light C. Ruler
B. Wire gauge D. Pull-push rule
21. A measuring tool used to measure the length of an object in centimeters
and inches
A. Test light C. Ruler
B. Wire gauge D. Pull-push rule
26. Which is a hazard that comes from heavy workloads and stress?
A. Chemical hazard Physical hazard
C. Biological hazard D. Psychological hazard
27. General cleanliness in the work place /work area is important method of
______.
34. Which method will you apply when general cleanliness is used in the
work place?
A. Administrative control C. Risk assessment
B. Hazard control D. Engineering control
36. This wire is made of multiple strand joined together to make a single
wire.
A. Flat cord C. stranded wire
B. Circuit Breaker D. Solid Wire
PLACER NATIONAL HIGH SCHOOL Document Type: PNHS-EXAM
Magsaysay, Placer, Surigao del Norte Revision No.: 00
School ID: 304837 Effective Date 01 October 2022
Email: 304837@deped.gov.ph Page No. 5 of 6
37. this is a duplex stranded used for temporary wiring installation and
commonly used in extension cord assembly.
A. Flat cord C. stranded wire
B. Circuit Breaker D. Solid Wire
38. this type of wire is made of single strand of copper or aluminum wire.
These are used in wiring installation inside and outside the building.
A. Flat cord B. stranded wire
C. Circuit Breaker D. Solid Wire
39. this kind of electrical materials are used to hold and anchor electrical
conduits in its proper position.
A. Clamps C. Connectors
B. Circuit Breaker D. Solid Wire
41. These devices hold and protect the lamp and are also called as_lamp
socket/receptacles. These come in many designs and sizes. They are
classified as flush, hanging (weather proof/chain) and surface types.
A. Electric Drill C. Knife Blade
B. Male Plug D. Lamp Holder
42. It is a device that connects and disconnects the flow of electric current
in a circuit. There are many shapes, design, and types and they are
classified as hanging, flush, and surface types.
A. Switch C. Fuse
B. Male Plug D. Lamp Holder
43. the device that act as a conveniences source of of electrical energy for
current consuming appliances. It is where the male plug of an appliance is
inserted and usually fasten on the wall or connected in extension cord.
A. Switch C. Convenience outlet
B. Male Plug D. Lamp Holder
50. This wire is made of multiple strand joined together to make a single
wire.
A. Flat cord C. stranded wire
B. Circuit Breaker D. Solid Wire