Professional Documents
Culture Documents
I. Masonry/Concrete
Product Description Application Thinner Coverage Drying Time Putty Primer Finishes
Use
Packaging
Latex and Acrylic Based Paint
Davies Pondo Flat Latex Water-based flat latex undercoat Brush or Water 25-30 2 hours in DAVIES® Davies Top Coat
White for interior, exterior and ceiling roller between coat Concrete
application Putty
4 L, 16L
Davies Roof Shield Acrylic Gloss Roof Paint for Brush, roller Water 20-25 Dry to touch in Megacryl Finish with 2 coats and
galvanized iron, cementitious roof or spray 8 hours Concrete let dry for two hours in
as well as masonry walls Primer or between coats
Recoatable Sealer (dry
For concrete, wood and metal between 5-24 for 2 hours) (gloss, semi-gloss)
roofing hours
4 L, 16L
Davies Megacryl Premium 100% acrylic water- Brush, roller Water 30 sq m / 4 L 30 mins, Concrete Davies 2 coats (Semi-gloss,
based interior and exterior paint, or spray recoating in 2- putty 1350
high hiding coverage 3 hours Concrete
Spot prime Megacryl
Stucco, masonry, plaster, bricks, with Davies Concrete
CHB, gypsum, acoustic board, 1350 primer and
bagasse board, properly primed Megacryl sealer (dry
wood and metal Concrete for 2 hours)
Primer and
Sealer
Boysen Permacoat Paint is a 100% acrylic latex paint Paint brush, Water 25-30 sq m Surface: 30 Boysen BOYSEN® 2 coats of Boysen
roller or /4L/coat minutes Masonry Permacoat permacoat Flat Latex
airless spray ™ Flat
Prepared by: Janelle Airene Moran
Concrete, stucco, brick plaster, Dry through: 2 Putty Latex #701
CHB, drywall and properly primed hours (interior) (White)
wood
Allow 1 hour Acrytex Cast
16l, 4l, 1l (white only) before (exterior)
recoating
Boysen Wallguard Dirt High-resistance to dirt, dust, smog paint brush, Water 25 - 30 square Surface dry 30 Acrytex Cast Acrytex 2 coats of Boysen Wall
Resisting Latex and mildew roller or meter / 4 liters minutes #1711 Primer Guard
airless spray /coat #1705
For areas near industrial areas, 1 hour before
along highways, medium and high- recoating
rise buildings
Titan Superflex Self-priming flexible coating that Brush and Water 18-22 sqm Surface dry: 1 Self- 3 coats of Titan
reflect UV rays roller, do not hour priming Superflex
use in high
For protection and decoration of humidity 3 hours before
concrete surfaces recoating
4L
Nippon Weatherbond pure acrylic-based paint with non- Brush, roller, Water 11-13 sq m/liter Surface Dry: Nippon ACS Nippon 2 coats of Nippon
added lead and mercury which is air spray Depends on Putty Vinilex Wall Weatherbond
specially formulated for exterior (dilute with humidity sealer /
walls. This premium exterior 20% water), Nippon
emulsion is formulated to provide airless spray Dry Through: Acrylic Wall
at least 5 years 45 mins Sealer
protection against fungus and
algae growth, chalking and flaking Recoat in 2-3
hours
decoration and protection of
exterior walls
5L, 20L
4L
4L
Davies BioFresh A water-based, stain resistant paint brush, Water 20-25 sq m/ 3 Surface dry Concrete Davies 2 coats of Davies
premium interior paint. It exhibits roller or liters/ coat 20-30 mins Putty 1350 Biofresh
excellent hydrophilic stain airless spray Megacryl
resistance combined with good Recoat in 2 Concrete Sheen, flat and semi-
hydrophobic stain removal, can be hours primer and gloss
easily claned, anti-bacterial sealer
4L, 16L
Enamel/QDE
Boysen QDE is an alkyd type paint that provides Brush/roller Paint 20 - 25 square Surface Dry- 5 Plasolux Boysen 2 coats of QDE
great durability while being noted Thinner meter /4 liters hours (wood) Flatwall
as a fast drying paint /coat Dry through: 2 Enamel
hours (Wood)
For wood and metal Recoat in 8
hours Boysen
16 L (white only, 4L, 1L , ¼ L Red Oxide
Primer,
Rust Off,
Prime
Guard
(Metal)
Davies Flat Wall Enamel alkyd-based enamel Brush, roller ¼ L of 20 - 25 square Surface Dry : Davies Pro-lux Davies 2 coats of flat wall
or spray Paint meter /4 liters Approximate 1 Glazing Putty Interior enamel
For interior walls, ceilings and thinner/ 4 /coat hour, Re-coat : Primer
interior wood finishes liters of Overnight Spot putty with and Sealer
paint Davies Interior (dry
16L, 4L, 1L Primer and overnight)
Sealer
4L, 1 L
Wood Stain
Davies Oil Wood Stain A lightly pigmented oil-rich finish Synthetic 20-25 m² per 4 8 hours before Davies Paste 2nd Coat : DAVIES®
bristle brush liter per coat recoating Wood Filler Oil Woodstain
cabinets, doorjamb, floor, furniture, 3rd Coat : DAVIES®
and wood works 701 Hi-Solids Sanding
Sealer
4L, 1 L Finish Coat : DAVIES®
Hi- Solids Clear
Lacquer or other Clear
Varnishes
Boysen Hudson Hudson® Polyurethane Floor Natural hair 20 - 25 sq.m./4 Surface dry: 1st and 2nd 3rd to 5th: Hudson®
Polyurethane Floor Sealer is an aromatic, two- brush or air liters/coat Thirty (30) coats: Polyurethane Floor
Varnish Sealer component urethane sealer to spray minutes Hudson® Varnish Topcoat
provide good adhesion of Polyuretha
Hudson® Polyurethane Floor Dry through: ne Floor
Varnish Topcoat One (1) hour Varnish
Sealer
As primer for parquet and wooden Recoat after 5
floors hours
Textured Paint
Boysen Acrytex Paint is an acrylic solvent-based coating Mortar gun 15-18 sqm/ 4L/ Surface dry: Plain Finish:
that forms a seamless, non- coat (textured Thirty (30) 1. Prime surface with BOYSEN® Acrytex™
porous, watertight film that repels finish) minutes Primer #1705.
water and prevents seepage. It is 2. Fill hairline cracks and minor surface
noted for its excellent adhesion 25-30 sqm Dry through: imperfections with BOYSEN® Acrytex™ Cast
and long-term durability. Creates a (plain finish) Two (2) hours #1711 using a putty knife.
very tight film, serving as a 3. Spot prime puttied portions with BOYSEN®
moisture sealant for concrete and Acrytex™ Primer #1705.
a stain inhibitor for wood. 4. Apply 2-3 coats of BOYSEN® Acrytex™
Topcoat of desired sheen by brush, roller or
For exterior and interior masonry, spray.
wood and properly primed steel
Textured Finish:
1. Prime surface with BOYSEN® Acrytex™
Primer #1705.
2. Spray BOYSEN® Acrytex™ Cast #1711 with
mortar gun. Press Acrytex™ Cast with wooden
roller 10-15 minutes after spraying.(Note: wet
wooden roller with BOYSEN® Acrytex™
Reducer #1750 to prevent the roller from
sticking to the cast).
3. Apply 2-3 coats of BOYSEN® Acrytex™
Topcoat of desired sheen by brush, roller or
spray.
DutchBoy Versatex Dutch Boy® Versatex™ is a water- Use as 5-6 sq m Surface dry: 2 Wood Dutch boy Wood Dutch Texture:
Interior Texture Finish based patterned finish supplied hours glazing putty Boy Classic Flat Versatex
Recoat in 8-12 (Wood) wall enamel
interior use on primed surfaces hours (wood) Topcoat: Dutch
such as concrete, drywall, and Concrete Dutch Boy Nalcrete
properly primed wood. Boy Concrete Concrete Dutch Latex (flat, semi-
Putty (concrete) Boy Nalcrete gloss, gloss)
4L Flat Latex
(concrete)
Davies Megacryl Gloss A pure acrylic emulsion For Chalking 20-25 New Concrete
Emulsion especially formulated to protect 1 Treat with Davies® 100-X Concrete Neutralizer.
concrete surfaces from 2 Wash off white crystals with water using high pressure hosing.
dampness while giving a fresh 3 Apply one coat of Davies® 550 Megacryl Clear Gloss Emulsion by brush or
look spray.
1, 4L Old Surfaces
1 Brush-off or wipe-off chalky surfaces.
2 Remove all loose paint, dust, dirt, and other contaminants.
3 Apply one coat of Davies® 550 Megacryl Clear Gloss Emulsion by brush or
spray.
Boysen Chalk Blocker is a water-based, low VOC Chalking 25-30 sq m/ gallon Use as primer when repainting chalky surfaces
paint for priming previously Surface dry: 1-2 hours, dry through 2 hours
painted masonry surfaces Application: brush/roller
where the existing paint film is
chalky.
4L
Boysen Skimcoat BOYSEN® Skimcoat™ #7750 Honeycomb and 0.4kg/ sq m Surface Prep: Remove oil, grease, dust, dirt, contaminants, and all loose grit and
is a special bonding paste that concrete surface mortar from the surface.
is mixed with cement and defects Recommended Defects on concrete more than 5 mm thick should be corrected using mechanical
applied on concrete to correct thickness is 0.3- sanders/grinders.
surface imperfections prior to 4mm Moisten the concrete before application.
painting. It repairs bubbles,
honeycomb and concrete Mixing Procedure: Put BOYSEN® Skimcoat™ #7750 on a suitable container
defects on waviness and (plastic bucket) and mix with cement at 1:1 ratio by weight until a lump-free
plumbness up to 4 mm thick. homogeneous paste is reached. Do not add water. Use portland cement (for
ordinary cement color) or white cement (to produce a white finish). No need to
25 kg per pail neutralize.
Application: Using a steel trowel, apply the mixture thinly on the surface by
pressing the edge of the trowel firmly on the concrete until all areas are covered.
Let it dry for at least 30 minutes before applying the second coat (if necessary).
If trowel marks are visible, let surface dry for at least 30 minutes before sanding to
further smoothen surfaces.
No need to neutralize the surface. Allow at least 14 days before painting.
Boysen Aquaseal is a non-silicone protective Efflorescence, 8 sq m/ gallon BOYSEN® Aquaseal™ #99 should be applied liberally to saturate the surface.
sealer designed to impart reduces cracking Generous overlapping of passes is recommended until it drips down about 6
maximum water repellancy to a and spalling inches on masonry.
4-l can
Waterproofing
Product Type Description Coverag Application
Packaging e
Boysen Plexibond Cementitious is a specially formulated 5-6 sq m/ Surface Prep: Apply on bare concrete, wood or metal, scraped off existing paint, new masonry
acrylic polymer designed for 4L should be allowed to cure 14-28 days, wet masonry first before applying plexibond mix to avoid
compounding with Pozzolan abrupt drying and cracking of cement
or Portland cement. Application Mix 6.5 to 7,5kgs of cement to 4 liters of Plexibond. Add cement to Plexibond slowly
while stirring to avoid lumping. Strain mixture to sift out lumpy materials. Mix in small batches.
4L Mixture workability is 30 minutes while potlife is 2 hours
For vertical surfaces such as firewalls, apply two coats of Plexibond™ mixture by textured roller
(for orange peel texture finish) or three coats by brush (for plain finish) while maintaining coverage
rate at 5-6 sq. meters per gallon. Recoating interval is 1-2 hours.
For horizontal surfaces such as roof decks, parapets, canopies and ledges, apply five coats by brush
or three coats by textured roller.
Reinforce joints, corners and active cracks susceptible to cracking or movement with a strip of
fiberglass matting. Put on the matting immediately after the second coat, while the mixture is still wet.
The matting should adhere to the mixture. Make sure the Plexibond™ coating and the matting is
completely dry before applying succeeding coats. The matting should be completely covered by the
mixture. Let dry for one day, then apply a bond coat by brushing BOYSEN® Plexibond™ straight
from the can prior to laying out mortar topping.
For filling large cracks, add 3 parts by volume of fine uniform-sized sand to 1 part cement and mix
with BOYSEN® Plexibond™ to trowellable consistency.
Davies Plexitite Cementitious - - -
Island Concrete Bond Cementitious 10 – 12 Mixing procedure : Add Portland cement into Concreto Bond liquid and mix thoroughly to form a soft
sq.m. / creamy paste.
gal Application method : roller
5kg-20kg
Davies Mondo Liquid Elastomeric is a high-quality water-based 8-10 sq
Sealant elastic sealant and m/L
waterproofing membrane for
multi-substrates. It is a
versatile gap filler and sealer
to stop water leakages and
moisture ingression in roofs,
Prepared by: Janelle Airene Moran
gutters, PVC pipes, metal
sheets, and other
construction materials such
as concrete and wood.
4L, 1 L, 1/4L
Island Hydrobond Underlay is a two-packed multi-purpose 4-5 1. Mix component Powder Mix #300PM unto Hydrobond Liquid 3001 using mechanical stirrer
Waterproofing Membrane Concrete Waterproofing for square preferably using non-metallic bucket. The product is supplied in pre-measured containers.
Membrane the construction industry meter/ 2. Pre-wet surface with tap water till sufficiently below saturated.
made from specially 0.5 3. Roller or Brush – apply the mixture follwing below instruction ;
developed water based gallon First Coat : Haft of a gallon set to be rolled evenly to a measured area of 4-5 square
acrylic polymer. This product meters. This spread rate will result to about 1mm dry membrane. Allow to set 4-6
is designed to be hours for recoat.
compounded with powder Second Coat : Apply the other half to same coated area for a final total dry thickness
aggregate containing of 2mm. Make sure to apply stripe coat along corners using brush.
Portland Cement giving 4. Flood test – flood with water after minimum of 2 days cure.
impregnable coating layer Test duration should run for 24 hours. Touch-up any sign of failure, if any, with the
with high tensile strength, same mixture.
flexibility, low shrinkage and 5. Drain water, surface now ready for resurfacing with concrete
water tight.
800g
Sika Top seal- 107 Integral Used in external and internal Brush or trowel
waterproofing for basements,
swimming pools, watertanks,
flat roofs, balconies, retaining
walls, sea walls, tunnels