Professional Documents
Culture Documents
13 Wireline Fishing
13 Wireline Fishing
Recommendations
• Close Wireline Valve
• Bleed Pressure off Lubricator.
• Attach Cutter to wire.
• Re-Install Lubricator
• Pull 100lbs above wire weight
• Open Wireline Valve and allow cutter to fall to
Rope Socket
• Cut wire at Rope Socket
• Retrieve wire
• Prepare program to retrieve toolstring.
Closing the Wireline Valve
against the
Wire
Closing Hydraulic Wireline
Valve against the
Wire
Kinley Snipper
Application:
• Designed to cut the wire
approximately 2.5” above
Rope Socket upon impact
Upside-down Snipper
and
Go-Devil
Application:
• Designed to cut the wire
approximately 22” above
Rope Socket after Go-Devil
impacts plunger.
• Used where rope socket
might not be clear.
• Used in deviated well
where gas lift mandrels
might cause standard
cutter to cut the wire high.
Rotating Knife
Wire Cutter
Application:
• Designed to cut
the wire
approximately
1” above Rope
Socket
Other Considerations
Nipple Sizes
No-Go Nipples
Cutter Bars
Go-Devils
Weight Bar
Jars
Knuckle
Joint
Tubular Jars
Applications:
• Dislodge stuck Subsurface
Flow Controls.
• Dislodge or Break Junk.
• Drive an object downhole.
• Cut wire at Rope Socket
Sizing the Blind Box
Tubing ID – (Rope Socket OD/2) + (Wire OD/2)
Equals the Blind Box OD
BLIND BOX
Minimum Size
BLIND BOX
Maximum Size
Wire Finder
Applications:
• Locate and ball top of wire
Wire Grab
Applications:
• Retrieve Wire Left in Well.
• Chip Ice Plugs.
• Retrieve Packing and
Elements.
Lost Tools and Wire!
Conditions
• Toolstring is not stuck
• Wire broke while running
into well.
Recommendations
• Close Swab Valve
• Bleed Pressure off
Lubricator.
• Tie new Rope Socket attach
Toolstring using tubular jars
• Attach Wire Finder to
Toolstring
• Re-Install Lubricator
• Run Wirefinder to top of wire
and locate.
• Run Wire Grab and retrieve
wire and toolstring.
• Close Wireline Valve on Wire
install bar clamp.
• Prepare program to retrieve
wire and toolstring.
Wire Finder
Applications:
• Locate and Ball Top of
Wire
Wire Grab
Applications:
• Retrieve Wire Left in Well.
• Chip Ice Plugs.
• Retrieve Packing and
Elements.
Closing Hydraulic Wireline
Valve against the
Wire
Bar Clamp
Toolstring Blown Uphole!
Conditions
• Toolstring is stuck
• Wire is still attached to
the unit at the surface.
Recommendations
• Close WL Valve, Bleed
Pressure off Lubricator.
• Attach Flat Bottom Go-Devil
to Wire, Replace Lubricator,
Pull 100# over wire weight,
Open WL Valve and allow
Go-Devil to Drop.
• Close WL Valve, Bleed
Pressure off Lubricator.
• Attach Cutter to Wire,
Replace Lubricator, Pull
100# over wire weight, Open
WL Valve and allow Cutter to
Drop.
• Pull wire Out of well
• Prepare program to retrieve
Go-Devil and Toolstring.
Rotating Knife
Wire Cutter
Application:
• Designed to cut
the wire
approximately
1” above Rope
Socket
Toolstring Blown Uphole!
Conditions
• Toolstring is stuck
• Wire is not attached to the
unit at the surface.
Recommendations
• Close Swab Valve, Bleed
Pressure off Lubricator.
• Prepare program to retrieve
wire and tools.
• Run Wirefinder to top of wire
and locate.
• Run Wire Grab, break and
retrieve wire.
Wire Finder
Applications:
• Locate and Ball Top of
Wire
Wire Grab
Applications:
• Retrieve Wire Left in Well.
• Chip Ice Plugs.
• Retrieve Packing and
Elements.
Safe Procedures Established
Experience Gained
Tools Developed
all for
Slickline Fishing Operations
HALLIBURTON
is the
World Leader
Thank You