Professional Documents
Culture Documents
OXIGENO
OXIGENO
Circuit Schematic
Additional Wiring
Monitor Conditions
When Monitored:
Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is off.
Set Conditions
Set Condition:
Desired state does not equal Actual state. One Trip Fault. Three good trips to turn off the MIL.
Possible Causes
Possible Causes
(K99) O2 1/1 HEATER CONTROL CIRCUIT OPEN
(Z42) O2 1/1 HEATER GROUND CIRCUIT OPEN
(K99) O2 1/1 HEATER CONTROL CIRCUIT SHORTED
TO BATTERY VOLTAGE
O2 SENSOR
PCM
Diagnostic Test
1) ACTIVE DTC
Yes
Go To 2).
No
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 2 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
Measure the resistance across the O2 Sensor Heater element between the O2 Heater Control terminal and
the O2 Heater ground terminal at the component.
Is the O2 Sensor Heater Element resistance between 2.0 and 30.0 ohms?
Yes
Go To 3).
No
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 3 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
With a scan tool, actuate the O2 1/1 Heater Test with the Sensor harness connector still disconnected.
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 4 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
Using a 12-volt test light connected to ground, probe the (K99) O2 1/1 Heater Control circuit in the O2
Sensor harness connector.
Does the test light illuminate brightly and flash on and off during the actuation?
Yes
Go To 4).
No
Go To 5).
4) (Z42) O2 HEATER GROUND CIRCUIT OPEN
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 5 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
Measure the resistance between an engine ground and the (Z42) O2 1/1 Heater ground circuit in the O2
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 6 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
Yes
No
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 7 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 8 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
Using a 12-volt test light connected to ground, probe the (K99) O2 1/1 Heater Control circuit in the O2
Sensor harness connector.
Yes
Repair the short to battery voltage in the (K99) O2 1/1 Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST .
No
Go To 6).
6) (K99) O2 1/1 HEATER CONTROL CIRCUIT OPEN
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 9 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 10 © 2011 Mitchell Repair Information Company, LLC.
2006 Jeep Grand Cherokee Limited
2006 ENGINE PERFORMANCE Electrical Diagnostics - 3.7L/4.7L/5.7L/6.1L - Grand Cherokee
CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness
connectors will damage the PCM terminals resulting in poor terminal
to pin connection. Install Miller Special Tool #8815 to perform
diagnosis.
Measure the resistance of the (K99) O2 1/1 Heater Control circuit from the O2 Sensor harness connector
to the appropriate terminal of special tool #8815.
Yes
Go To 7).
No
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all
Power and Ground circuits.
Yes
Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST .
No
Replace and program the Powertrain Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST .
sábado, 19 de febrero de 2022 01:48:41 p.m. Page 11 © 2011 Mitchell Repair Information Company, LLC.