Professional Documents
Culture Documents
Mongoose PT Mud Cleaner
Mongoose PT Mud Cleaner
For
Per Assembly
9671901-01
9671902-01, -02
9671903-01, -02
9671904-01, -02
9671905-01, -02, -03, -04, -05
P. O. Box 42842
Houston, TX 77242-2842
All other products, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective owners.
All rights reserved. This publication is the property of, and contains information proprietary to
MI-Swaco. No part of this publication may be reproduced in any form or by any means,
including electronic, mechanical, or otherwise, without the prior written permission of MI-
Swaco.
i
Page
5.2: Electrical Connections to Control Panel …………………. 26
Figure 5.2a – 380V/50 Hz Wiring Schematic ……………. 27
5.3: Installation, Location and Support ………………………. 28
Figure 5.3a ………………………………………………. 28
5.4: Typical Trough and Shale Slide Installation …………….. 29
5.5: Inlet Line and Bypass Line Connections ………………… 29
Figure 5.5a ……………………………………………..… 29
5.6: Screen Installation ………………………………………. 30
Figure 5.6a ..……………………………………………… 31
5.7: Screen Selection Chart …………………………………… 31
5.8: Movement, Shipping ……………………………………... 32
Figure 5.8a - Shipping Bracket ……..…………………… 32
Figure 5.8b - Shipping Bracket……………………………. 32
Procedure 1 ………………………………………………. 33
Procedure 2 ………………………………………………. 33
ii
Page
Section 8.0: Startup and Operation …………………………………………. 52
8.1: Start up…………………………………………………….. 52
8.2: Deck Angle Adjustment ………………………………….. 53
Figure 8.2a ………………………………………………... 53
8.3: Screen Blinding …………………………………………... 54
Section 10.0: Drawings and Parts List per Assembly 9671901-01 …………... 57
Figure 10.0a – Parts List for 9671901-01 …………..……. 57
10.1: Drawings and Parts List 9671688-02 ..…………………… 58
Figure 10.1a – Parts List for 9671688-02 …….…………... 58
10.2: Drawings and Parts List per Assembly 9671843 …………. 60
Figure 10.2a – Parts List for 9671843 ……………………. 60
10.3: Drawings and Parts List per Assembly 9671738-01 .…….. 61
Figure 10.3a – Parts List for Assembly 9671738-01 .……. 61
10.4: Drawings and Parts List per Assembly 9671906 ………… 62
Figure 10.4a – Parts List for Assembly 9671906 ………… 62
10.5: Drawings and Parts List per Assembly 9622220 …………. 63
Figure 10.5a – Parts List for Assembly 9622220 ………… 63
10.6: Recommended Spare Parts for 9671901-01……….……… 64-66
Section 11.0: Drawings and Parts List per Assemblies 9671902-01, -02……... 68
11.0.1: Assembly 9671902-01………………………………… 68
Figure 11.0.1a – Parts List for 9671902-01 ………. 68
11.0.2: Assembly 9671902-02………………………………… 69
Figure 11.0.2a – Parts List for 9671902-02 ………. 69
11.1: Drawings and Parts List 9671688-02...…………………… 70
Figure 11.1a – Parts List for 9671688-02 …….…………... 70
11.2: Drawings and Parts List per Assembly 9671843 …………. 72
Figure 11.2a – Parts List for 9671843 ……………………. 72
11.3: Drawings and Parts List per Assembly 9671738-01............ 73
Figure 11.3a – Parts List for Assembly 9671738-01........... 73
11.4: Drawings and Parts List per Assembly 9671906 ………… 74
Figure 11.4a – Parts List for Assembly 9671906 ………… 74
11.5: Drawings and Parts List per Assembly 9622220 …………. 75
Figure 11.5a – Parts List for Assembly 9622220 ………… 75
11.6: Drawings and Parts List per Assemblies
9671947 and 9671954……………………………………. 76
11.6.1: Assembly 9671947……………………………….. 77
Figure 11.6.1a – Parts List for 9671947………..… 77
11.6.2: Assembly 9671954……………………………….. 78
Figure 11.6.2a – Parts List for 9671954………..… 78
11.7: Drawings and Parts List per Assembly 9621280 …………. 79
Figure 11.7a – Parts List for Assembly 9621280 ………… 79
iii
Page
11.8: Recommend Spare Parts for 9671902-01, -02….…………. 80
11.8.1: Spare Parts List for 9671902-01…………………... 80-82
11.8.2: Spare Parts List for 9671902-02…………………… 83-85
Section 12.0: Drawings and Parts List per Assemblies 9671903-01, -02……... 87
12.0.1: Assembly 9671903-01………………………………… 87
Figure 12.0.1a – Parts List for 9671903-01 ………. 87
12.0.2: Assembly 9671903-02………………………………… 88
Figure 12.0.2a – Parts List for 9671903-02 ………. 88
12.1: Drawings and Parts List 9671688-02 ..…………………… 89
Figure 12.1a – Parts List for 9671688-02 …….…………... 89
12.2: Drawings and Parts List per Assembly 9671843 …………. 90
Figure 12.2a – Parts List for 9671843 ……………………. 90
12.3: Drawings and Parts List per Assembly 9671738-01…….... 91
Figure 12.3a – Parts List for Assembly 9671738-01……... 91
12.4: Drawings and Parts List per Assemblies
9671919 and 9671920…………………….……………… 92
12.4.1: Assembly 9671919……………………………….. 93
Figure 12.4.1a – Parts List for 9671919 ………… 93
12.4.2: Assembly 9671920……………………………….. 94
Figure 12.4.2a – Parts List for 9671920 ………… 94
12.5: Drawings and Parts List per Assembly 9622220 …………. 95
Figure 12.5a – Parts List for Assembly 9622220 ………… 95
12.6: Drawings and Parts List per Assembly 9671954 …………. 96
Figure 12.6a – Parts List for Assembly 9671954 ………… 96
12.7: Drawings and Parts List per Assembly 9621280 …………. 97
Figure 12.7a – Parts List for Assembly 9621280 ………… 97
12.8: Recommend Spare Parts for 9671903-01, -02…..…………. 98
12.8.1: Spare Parts List for 9671903-01…………………... 98-100
12.8.2: Spare Parts List for 9671903-02…………………… 101-103
Section 13.0: Drawings and Parts List per Assemblies 9671904-01, -02……... 105
13.0.1: Assembly 9671904-01………………………………… 105
Figure 13.0.1a – Parts List for 9671904-01 ………. 105
13.0.2: Assembly 9671904-02………………………………… 106
Figure 13.0.2a – Parts List for 9671904-02 ………. 106
13.1: Drawings and Parts List 9671688-02 ..…………………… 107
Figure 13.1a – Parts List for 9671688-02 …….…………... 107
13.2: Drawings and Parts List per Assembly 9671843 …………. 108
Figure 13.2a – Parts List for 9671843 ……………………. 108
13.3: Drawings and Parts List per Assembly 9671738-01 .…….. 109
Figure 13.3a – Parts List for Assembly 9671738-01 .……. 109
iv
Page
13.4: Drawings and Parts List per Assemblies
9671966 and 9671967……………………..……………… 110
13.4.1: Assembly 9671966……………………………….. 111
Figure 13.4.1a – Parts List for 9671966 ………… 111
13.4.2: Assembly 9671967……………………………….. 112
Figure 13.4.2a – Parts List for 9671967 ………… 112
13.5: Drawings and Parts List per Assembly 9622220 …………. 113
Figure 13.5a – Parts List for Assembly 9622220 ………… 113
13.6: Recommend Spare Parts for 9671904-01, -02..............…... 114
13.6.1: Spare Parts List for 9671904-01…………………... 114-116
13.6.2: Spare Parts List for 9671904-02…………………… 117-119
v
Page
14.6: Drawings and Parts List per Assembly 9671947 …………. 136
Figure 14.6a – Parts List for Assembly 9671947 ………… 136
14.7: Drawings and Parts List per Assembly 9621280 …………. 137
Figure 14.7a – Parts List for Assembly 9621280 ………… 137
14.8: Recommend Spare Parts for Assemblies
9671905-01, -02, -03, -04, -05…………………...……….. 138
14.8.1: Spare Parts List for 9671905-01…………………….. 138-140
14.8.2: Spare Parts List for 9671905-02…………………… 141-143
14.8.3: Spare Parts List for 9671905-03…………………… 144-146
14.8.4: Spare Parts List for 9671905-04…………………… 147-149
14.8.5: Spare Parts List for 9671905-05…………………… 150-152
vi
1.0: Intended Usage
This documentation is intended to be used by field engineering,
installation, operation, and repair personnel for proper installation and
maintenance of equipment manufactured by MI-Swaco. Every effort has
been made to ensure the accuracy of the information contained herein.
MI-Swaco will not be held liable for errors in this material, or for
consequences arising from misuse of this material.
1.1: Symbols
Notes, cautions, and warnings appear throughout this manual to provide
additional information, and to advice of specific actions to protect
personnel from potential injury or fatal conditions. They also inform
actions necessary to prevent equipment damage or conditions that may
void equipment warranties.
The symbols that may be shown on the package should be noted. Their
significance is as follows.
1
1.2: PPE’s (Personal Protective Equipment)
All personnel working on or around MI-Swaco equipment must wear PPE.
Below is a list of what should be worn by personnel unless Local or
National codes require different PPE to be worn.
1.3: Safety
Equipment manufactured by MI-Swaco is installed and operated in a
drilling rig environment involving hazardous operations. Proper care is
important for safe and reliable equipment operation and rig personnel’s
safety. Operation and service procedures described herein this manual are
recommended methods of performing proper operations and safety
methods. Consult Local or National codes for any other safety regulations
required for the type of environment.
2
2.0: Mud Cleaner General Arrangement Drawings
3
2.2: Mud Cleaner GA Drawing per Assembly 9671902-01
4
2.3: Mud Cleaner GA Drawing per Assembly 9671902-02
5
2.4: Mud Cleaner GA Drawing per Assembly 9671903-01
6
2.5: Mud Cleaner GA Drawing per Assembly 9671903-02
7
2.6: Mud Cleaner GA Drawing per Assembly 9671904-01
8
2.7: Mud Cleaner GA Drawing per Assembly 9671904-02
9
2.8: Mud Cleaner GA Drawing per Assembly 9671905-01
10
2.9: Mud Cleaner GA Drawing per Assembly 9671905-02
11
2.10: Mud Cleaner GA Drawing per Assembly 9671905-03
12
2.11: Mud Cleaner GA Drawing per Assembly 9671905-04
13
2.12: Mud Cleaner GA Drawing per Assembly 9671905-05
14
3.0: Introduction
The capacities of the D-Silters are 600 gpm [2271 Lpm] (4T4 D-Silter),
900 gpm [3407 Lpm] (6T4 D-Silter), 1200 gpm [4542 Lpm] (8T4 D-
Silter), and 1500 gpm [5678 Lpm] (10T4 D-Silter). The capacities of the
D-Sander are 500 gpm [1893 Lpm] (1-12 D-Sander), 1000 gpm [3785
Lpm] (2-12 D-Sander), and 1500 gpm [5678 Lpm] (3-12 D-Sander). The
solids discard rates from the hydrocyclones is relatively low compared to
the shaker capacity. This enables fine mesh screens to be used,
minimizing the fine solids returned to the active fluid system. Long beach
lengths on the shaker enable a high fluid recovery rate.
15
The Mud Cleaner can also be used as a primary solids removal devise by
using the bypass located on the D-Silter, which will allow the mud from
the tank to flow thru the Mongoose PT Shaker.
3.3.1: D-Sander
16
3.3.2: D-Silter
17
MI-Swaco D-Sanders and D-Silters are hydrocyclone solids separators.
As their name implies, they remove “sand” and “silt” size particles from
the drilling fluid. To be effective, the clones should be sized to process
150% of the circulation rate and the mud to be desilted should be fed from
the desanded mud compartment. MI-Swaco clones are designed for
excellent separation at about 45 psi (3.16 kg/cm²) input pressure for 9.5
ppg (1.14 kg/liter) muds. For other mud weights, the best pressure is
proportionately higher or lower. At higher feed pressures, the throughput
capacity is increased and the removal of finer silts is slightly improved,
but the increased wear rate usually more than offsets these benefits.
Separation will be more efficient in low viscosity muds and in muds with
low total solids content.
18
The new Fluid Distribution System is mounted above the screen deck.
The fluid is redirected from the inlet line through the diverter box into a
half pipe that is welded to the back of the screen deck. The flow enters the
half pipe at the bottom and spins up and back through the fluid stream.
This reduces the velocity of the fluid before it makes contact with the
screening surface.
Since the Fluid Distribution System is mounted above the screen deck, no
trap exists to collect solids. As the fluid passes through the diverter box it
sweeps the box clean.
The shaker is equipped with two (2) or three (3) explosion proof vibratory
motors. The unique mounting of these vibrators produces a true linear
motion for a two (2) motor version and a balanced elliptical motion for a
three (3) motor version. With the two (2) motor version the G-force on
the shaker will be increased by 20%. The increased force and linear
motion will result in shorter screen life if used continuously. When the
three (3) motor version is in operation, the unit will produce a balanced
elliptical deck motion slowing down the solid conveyance and resulting in
much drier discharge and longer screen life.
19
3.5: Applications Mud Cleaner
20
4.0: Unit Descriptions
4.1: Physical
Note: All weights shown below are approximate for complete units.
Overall
Unit Weight Length Width Weir Height
Height
Mongoose Mud Cleaner 6388 lbs 113.33 63.12 in 97.58 in 35.00 in
per Ass’y 9671901-01 (2898 Kg) (2879 mm) (1603 mm) (2479 mm) (889 mm)
Mongoose Mud Cleaner 7789 lbs 113.33 63.12 in 97.58 in 35.00 in
per Ass’y 9671902-01 (3533 Kg) (2879 mm) (1603 mm) (2479 mm) (889 mm)
Mongoose Mud Cleaner 8378 lbs 113.33 63.12 in 97.58 in 35.00 in
per Ass’y 9671902-02 (3800 Kg) (2879 mm) (1603 mm) (2479 mm) (889 mm)
Mongoose Mud Cleaner 7905 lbs 113.33 63.12 in 93.82 in 35.00 in
per Ass’y 9671903-01 (3586 Kg) (2879 mm) (1603 mm) (2383 mm) (889 mm)
Mongoose Mud Cleaner 7985 lbs 113.33 63.12 in 92.05 in 35.00 in
per Ass’y 9671903-02 (3622 Kg) (2879 mm) (1603 mm) (2339 mm) (889 mm)
Mongoose Mud Cleaner 6042 lbs 113.33 63.12 in 92.05 in 35.00 in
per Ass’y 9671904-01 (2741 Kg) (2879 mm) (1603 mm) (2339 mm) (889 mm)
Mongoose Mud Cleaner 6130 lbs 113.33 63.12 in 92.05 in 35.00 in
per Ass’y 9671904-02 (2781 Kg) (2879 mm) (1603 mm) (2339 mm) (889 mm)
Mongoose Mud Cleaner 7405 lbs 113.33 63.12 in 92.05 in 35.00 in
per Ass’y 9671905-01 (3359 Kg) (2879 mm) (1603 mm) (2338 mm) (889 mm)
Mongoose Mud Cleaner 7485 lbs 113.33 63.12 in 92.05 in 35.00 in
per Ass’y 9671905-02 (3395 Kg) (2879 mm) (1603 mm) (2338 mm) (889 mm)
21
5.0: Inspection, Preparation, Installation
Before setting up and operating the Mongoose PT Mud Cleaner, inspect all goods
as received from the shipping company. A claim for damage or loss should be
reported immediately to the carrier and to MI-Swaco. Also, check the bill of
lading for any separately shipped items, including manuals and CD’s.
22
5.1: Unit Preparation
Read all instructions carefully and completely before you begin. Failure
to do so may result in personal injury or damage to the equipment.
HARDWARE TO BE
REMOVED AND STORED
FOR FUTURE USE
(NOT SEEN HERE)
SHIPPINGBRACKET
(BOTH SIDES)
(MI-SWACO P/N: 9671809)
MOVE SHIPPING
BRACKET IN THIS
DIRECTION
LOOSEN HARDWARE
(DO NOT REMOVE) SHIPPINGBRACKET
(BOTH SIDES) (BOTH SIDES)
(MI-SWACO P/N: 9671809)
MOVE SHIPPING
BRACKET IN THIS
DIRECTION
Figure 5.1a: For (9671902-01, -02) and (9671903-01, -02) and (9671905-01, -02) only
23
3. Remove hardware shown in Figure 5.1b and store in a safe
place for reuse. Loosen hardware shown in Figure 5.1b on
both shipping brackets on discharge and feed end. Rotate
shipping bracket on discharge end per label on skid and
tighten down hardware. Pull shipping bracket on feed end
in direction shown in Figure 5.1b, and tighten down
hardware. (Note: All shipping bracket must be away from
basket before operation.)
MOVE SHIPPING
BRACKET IN THIS
DIRECTION
(BOTH SIDES)
3
LOOSEN HARDWARE LABEL
ROTATE SHIPPINGBRACKET
PER LABEL SHIPPINGBRACKET
(MI-SWACO P/N: 9671742)
(BOTH SIDES)
Figure 5.1c
24
6. Lockout power to unit before going to step 6.
7. Remove covers from motors see Motor manual in
Appendix-A.
8. Lock-in power to unit.
WARNING! : Keep all objects away from motors during step 8. Potential
personal injury or death could occur during bump starting of
motors.
Figure 5.1d
25
5.2: Electrical Connection to Control Panel
Follow the below procedure to insure proper electrical connection of
power supply to the shaker control panel.
WARNING! Use proper PPE’s stated in Section 1.2 and per Local or
National codes
26
Figure 5.2a: Wiring Schematic Diagram
27
5.3: Installation, Location and Support
The Mud Cleaner is shipped as a complete assembly and would be
normally mounted over the shale pit (see Figure 5.3a). The unit should be
mounted as level as possible before either welding or bolting the unit to
the tank, as deviations will alter the separating characteristics of the
screens. The pump feeding the clones operates best with a flooded
suction. If possible, mount the pump below the normal operating mud
level in the pit. If not, keep the suction lifted as little as possible and use a
check valve or foot valve in the suction line. The screens when installed
should be tight and free of wrinkles.
TYPICAL TROUGH
INSTALLATION HERE
SHALE PIT
Figure 5.3a
28
5.4: Typical Trough and Shale Slide Installation
Place a trough at desired fluid discharge location on the skid and place a
gate in the unused outlet. It may be necessary for a welder to add an
extension to the trough for the fluid to flow to the discharge tank (see
Figure 5.3a).
It is desirable to allow the cuttings to drop directly off the end of the
screen, but if this is not possible it will be necessary to connect a shale
slide from the end of the shaker to shale sump, to aid the flow of the
cuttings to the shale sump, the slope of the slide should be as steep as
possible (see Figure 5.3a, Section 5.3). Do not add the shale slide to the
basket, weld only to the skid.
O 10.0
254
17.5 31.6
444 802 15.5
10" BYASS LOCATION 394
6" BYPASS LOCATION
Figure 5.5a
29
5.6: Screen Installation
Screen installation requires minimal time or effort.
ATTENTION : Wear proper PPE equipment per Section 1.2. And wash down
the screen area prior to installing new screens.
30
BASKET SIDEWALL
WEDGE BRACKET
MIN. FLUSH WITH
BRACKET FOR TIGHTNESS
31
5.8: Movement, Shipping
If unit is moved or shipped from location, all shipping brackets must be in
place. To prepare unit for movement or shipping follow Procedure 1
below for Assemblies (9671902-01, -02), (9671903-01, -02) , (9671905-
01, -02) only. For Assemblies (9671901-01) , (9671904-01, -02) see
Procedure 2 below.
32
Procedure 1: Prepare Unit for Movement or Shipping
1. Lower unit to the lowest deck angle of -3° (See Section 6.1).
2. Loosen hardware holding shipping bracket on the feed end of
unit. See Figure 5.1b. (Do Not Remove)
3. Slide shipping bracket in opposite direction shown in Figure
5.1ba.
4. Locate hardware that was removed in Figure 5.1b and replace
in location were removed in Figure 5.1a and tighten.
5. Loosen hardware and rotate shipping bracket on discharge end
so that the tapped hole of the bracket is facing the basket. (See
shipping bracket label on skid or orientation.)
6. Tighten hardware in step 10 above in tapped hole of bracket.
7. Unit is ready for movement or shipping.
8. Once unit has been moved to new location go to Section 5.1
before unit is operated.
33
6.0: Unit Operation
There is a deck angle indicator plate located on both sides of the discharge
end of the unit. The pointer is located on the spring support bracket to
indicate deck angle. There are mechanical stops located on the indicator
plate at +3° and -3°
DECK ANGLE
ADJUSTMENT NUT
1-1/4"
GREASE FITTING
FOR JACK
DECK ANGLE
INDICATOR
DECK ANGLE
POINTER
Figure 6.1a
34
6.2: D-Silter Bypass Operation
The bypass mode on the D-Silter allows the stoppage of fluid flow to the
shaker screens and allows the unit to be used as a Flow Line unit. To
operate the bypass on various D-Silters that can be supplied with the Mud
Cleaner see procedures bellow.
BYPASS SHOWN
IN BYPASS OPERATION
MODE
BYPASS SHOWN
IN FLOWLINE SHAKER
MODE
BYPASS FLUID FLOW
WHEN IN BYPASS
MODE
FLOWLINE
CONNECTION
FLOWDIRECTION
Figure 6.2a
35
6.3: Three (3) Motor Control Panel 6930007 (380V, 50 Hz)
The three (3) motor control panel (6930007) has a selector switch that will
operate the unit either as a linear motion or an elliptical motion shaker.
The Linear motion operation is general used for operations while drilling
top-hole sections where heavy, high volume solids such as gumbo are
usually encountered. In these intervals, shakers need to generate high G-
forces to effectively move dense solids across the screens. Operating the
shaker in this mode will lead to lower screen life.
Figure 6.3a
36
7.0: Unit Maintenance and Part Replacements Procedures
The MI-Swaco Mud Cleaner has been designed to minimize routine
maintenance. Periodic cleaning of the shaker, D-sander and D-silter will
keep the unit at top efficiency. Wash the screens each time the shaker is
shut down. The screen deck rubber should be replaced when they show
signs of cracking or hardening (See Section 7.5).
Whenever possible, the entire inside of the shaker should be washed down
thoroughly to flush out caked and accumulated mud in the corners.
Figure 7.1a: Control Panel 3 Motor 380V/50 Hz Parts List (MI-Swaco #: 6930007)
37
P E
DOOR IS SHOWN OPEN
G
O D
B F
J
C I I
MS3 MS4
MS1 MS2
A L A L
H H H H
M M N N
Figure 7.1b: Control Panel 3 Motor 380/50 Hz Internal and External Components
(MI-Swaco #: 6930007)
38
7.2: Motor Maintenance
The motor requires no daily or weekly maintenance. Once every 3000
hours of operation as stated in Motor manual located in Appendix-A the
motor bearings must be lubricated. In effect this is twice year
maintenance. Refer to Motor manual located in Appendix-A for other
proper maintenance procedures.
39
7.5: Deck Angle Jack Replacement
To replace one or both deck angle adjustment jacks abide by the following
procedure.
SPRINGISOLATION WASHER
SPRING
SPRINGSUPPORT
WELDMENT
UNIT
POINTER
Figure 7.5a
40
7.6: Vibrator Motor Removal and Replacement Procedure
WARNING! : Use proper PPE’s per Section 1.2 and Local or National codes.
41
6. Hook proper lifting device to motor that is being replaced.
Use lifting points on motors (see Figure 1). Caution:
Motors are heavy, large motor 225 lbs (102 Kg) and
small motor 110 lbs (50 Kg). Apply a small amount of
tension to lifting device to keep motors from falling during
motor bolt removal.
7. Remove motor bolt and hardware.
8. Remove motor. Attention: Note motor wire inlet
location and direction on motor junction box before
removing motor.
9. Clean and inspect motor mounting surface for damage such
as cracks and surface defects (see Figure 3). Attention:
Make sure that both the motor mounting surface and
back of motor mount plate are clean and paint free.
10. Position new motor onto unit. Motor wire inlet location
must be located the same as the motor removed in step 8
above.
11. Install NEW motor mounting hardware (see Figure 3 and
Table 1). Quantity shown below is for one large motor and
one small motor. Attention: Note orientation of items 3
and 7, figure 3. Items must be installed as shown in
Detail A and B.
Large Motor
Item # Qty MI-Swaco P/N Description
1 4 1407169 HHCS M20-1.5 x 120 mm lg., Grade 10.9 Yellow Chromate
2 4 BM6S80043-01 Motor Washer
3 4 05-244 Lockwasher Schnorr M20
4 4 1305055 Nut, Hex M20-1.5, Grade 10.9 Yellow Chromate
Small Motor
5 4 1407144 HHCS M16-1.5 x 100 mm lg., Grade 10.9 Yellow Chromate
6 4 9671682 Washer, 16 mm Motor
7 4 05-248 Lockwasher Schnorr M16
8 4 1305040 Nut, Hex M16-1.5, Grade 10.9 Yellow Chromate
Table 1
42
12. Hand tighten all bolts.
13. Apply initial torque of 160 ft-lbs (217 N-m) to all bolts for
the large motors and 85 ft-lbs (115 N-m) for small motor
mounting bolts.
14. After all bolts have been torque to step 13, apply final
torque of 320 ft-lbs (430 N-m) to all large motor mounting
bolts and 170 ft-lb (230 N-m) for small motor mounting
bolts.
15. Re-install all fittings removed from step 5 into motor wire
inlet in order they were removed.
16. Feed wires into fittings of step 15 and reconnect them to
motor terminals noted in step 2.
17. Tighten (A) and (B) from step 3 and 4.
18. Lock-in power source to unit.
19. Run unit for 4 hours and retorqued all motor mounting
bolts to step 14.
MOTOR LIFT
POINT LOCATION
CABLE GLAND
A
MOTOR JUNCTION BOX
B
MOTOR LIFT
POINT LOCATION
FIGURE 1
FITTINGS TO MOTOR
JUNCTION BOX B A
MOTOR CABLE
CABLE GLAND
FIGURE 2
43
B
1 5
FIGURE 3
2 3
6
4
7
DETAIL A DETAIL B
44
7.7: Spring Removal and Replacement Procedure
45
7.8: Cable Gland Assembly Instructions
F C
2. Place the Entry onto the motor fittings or the control panel.
3. Determine length of cable to suit equipment.
Desired Length
46
Copper Braid
Insulation
6. Slide the Backnut, Middle nut, and Clamping ring over the cable.
Middle Nut
47
7. Push the copper braid over the clamping ring and cut the remaining
insulation at the base of the copper braid to expose the wires.
Copper Braid
Clamping Ring Copper Braid
Insulation
Clamping Ring
Wire
8. Slide the Spigot over the wires and push the spigot into the copper
braid until the end of the braid is up against the shoulder of the
spigot.
Clamping Ring
Copper Braid
9. Position the clamping ring over the copper braid and bring the
middle nut up to meet the entry.
48
10. Hand tighten the middle nut onto the entry and then turn with a
wrench until you hear a squeak. NOTE: Do not over tighten this
can cause damage to the copper braid.
11. Unscrew the middle nut and visually inspect that the braid has
been successfully clamped between the spigot and the clamping
ring.
12. The epoxy compound must be mixed into the ratio of 1:1 until both
colors have blended into one, without any streaks. NOTE: Rolling
and folding is the most effective method of obtaining an even
blend. NOTE: When handling this material the gloves supplied
must be worn.
49
13. Spread out the wires and pack in the epoxy compound.
14. With all gaps and voids filled, bring the wires back together and
pack more compound around out-side of the wires in a cone-shape.
15. Slide the brass pot over the spigot and remove any surplus
compound from the top of the brass pot and the joint face.
Brass Nut
Joint Face
50
16. Hand tighten the middle nut onto the entry and then tighten with a
wrench.
17. Hand tighten the back nut onto the middle nut and then tighten
with a wrench.
51
8.0: Start up and Operation
The following section provides instructions for normal operation. Before
operating the unit, make sure that you performed all steps in Section 5.1 and 5.2.
Once the unit has been installed, the only changes or adjustments that should be
made are screen mesh and deck angle adjustments. Screen selection will depend
upon your specified drilling parameters, such as circulating volume, mud
viscosity, penetration rate, etc. See Section 5.6 for screen installation and
removal procedure.
8.1: Start up
Once all steps in Section 5.1, 5.2, 5.3 and 5.6 have be completed, follow
the below procedure for start up of the unit.
ATTENTION! : Make sure all objects such as tools are clear from unit before
starting unit.
52
8.2: Deck Angle Adjustment
The manual jacking system is used to change the deck angle of screening
surface relative to the neutral position (0º). The angle adjustments are
from -3º to +3º degrees. It is not necessary to shut down the shaker before
changing the deck angle.
1-1/4" NUT
DECK ANGLE
INDICATOR PLATE
POINTER
Figure 8.2a
53
2. Use a manual ratchet or wrench to adjust the 1-1/4” nut
located on the top of the jack. Adjust each side to the
desired position. DO NOT ADJUST MORE THAN 2°
PER SIDE WHILE CHANGING DECK ANGLE.
54
9.0: Troubleshooting
55
Page Left Blank
56
10.0: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671901-01 (Shaker Mongoose PT 10T4 Mud Cleaner
3 Mtr. 380V, 50 Hz)
Item
Qty MI-Swaco P/N Description
#
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Ass’y Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
10T4 D-Silter Ass’y w/ Header Box Mongoose PT Mud
5 1 9671906
Cleaner
6 1 9650360 Nameplate ID Product M-I Swaco
7 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
8 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
9 1 9671839 Plate, Cover 10T4 D-Silter PT Mongoose Mud Cleaner
Figure 10.0a – Parts List for 9671901-01
57
10.1: Drawings and Parts List Control Assembly Kit (9671688-02)
A B C D
E 2
11
13
11 15 14 16
2x
7 8 7 8
8 7 9
8 7 ON BOTTOM OF ITEM 2
6 4 5
11 11 8 7
6 4 5 10
8 7 9 12
11 6 5 4 6
11
4 12
5 12
6 4 5
6 4 5
58
For proper supporting of motor cable see Cable Routing View and Table 1 below
CABLE #3
A B C D
E
CABLE #1
25
REF
CABLE #2
59
10.2: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671843 (Mongoose PT Effluent Skid Less Motors and
Controls)
60
10.3: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671738-01 (Basket Assembly, Mongoose PT MS Basket
/ 304 SS HDW (Metric)
61
10.4: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671906 ( 10T4 D-Silter Assy w/ Header Box Mongoose
PT Mud Cleaner)
62
10.5: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9622220 (Clone Twin 4” Urethane Complete w/ 1/2”
Apex)
2 2
63
10.6: Recommended Spare Parts for 9671901-01 Configuration
Items listed below are for 1 year of operating spares.
64
Spare Parts List Continued
65
Spare Parts List Continued
66
Page Left Blank
67
11.0: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671902-01 and 9671902-02
Assembly 9671902-01: Shaker Mongoose PT 2-12/10T4 Mud Cleaner
3 Motor 380V, 50 Hz
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
10T4 D-Silter Assembly w/ Header Box Mongoose PT Mud
5 1 9671906
Cleaner
6 1 9671947 2-12, D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
10 1 9671955 Weldment, Trough 2-12 D-Sander PT Mongoose Mud Cleaner
Figure 11.0.1a – Parts List for 9671902-01
68
11.0.2: Assembly 9671902-02 (Shaker Mongoose PT 3-12/10T4 Mud
Cleaner 3 Mtr. 380V, 50 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
10T4 D-Silter Assembly w/ Header Box Mongoose PT Mud
5 1 9671906
Cleaner
6 1 9671954 D-Sander 3-12 Stand w/ Clones Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
10 1 9671960 Weldment, Trough 3-12 D-Sander PT Mongoose Mud Cleaner
Figure 11.0.2a – Parts List for 9671902-02
69
11.1: Drawings and Parts List Control Assembly Kit (9671688-02)
A B C D
E 2
11
13
11 15 14 16
2x
7 8 7 8
8 7 9
8 7 ON BOTTOM OF ITEM 2
6 4 5
11 11 8 7
6 4 5 10
8 7 9 12
11 6 5 4 6
11
4 12
5 12
6 4 5
6 4 5
70
For proper supporting of motor cable see Cable Routing View and Table 1 below
CABLE #3
A B C D
E
CABLE #1
25
REF
CABLE #2
71
11.2: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671843 (Mongoose PT Effluent Skid Less Motors and
Controls)
Applies to main assemblies 9671902-01, -02
72
11.3: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671738-01 (Basket Assembly, Mongoose PT MS Basket
/ 304 SS HDW (Metric)
73
11.4: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671906 (10T4 D-Silter Assembly w/ Header Box
Mongoose PT Mud Cleaner)
Applies to main assemblies 9671902-01, -02
74
11.5: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9622220 (Clone Twin 4” Urethane Complete w/ 1/2”
Apex)
2 2
75
11.6: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671947 and 9671954
76
11.6.1: Assembly 9671947 (2-12 D-Sander Assembly Mongoose PT
Mud Cleaner)
77
11.6.2: Assembly 9671954 (3-12 D-Sander Sander with Clones
Mongoose PT Mud Cleaner)
78
11.7: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9621280 (Clone Assembly Urethane 12 in Grooved End)
5
1 6
6
2 3
4
79
11.8: Recommended Spare Parts for Assemblies 9671902-01 and
9671902-02
80
Parts List Continued
81
Parts List Continued
82
11.8.2: Recommended Spare Parts for Assembly 9671902-02
83
Spare Parts Lists Continued
84
Spare Parts List Continued
85
Page Left Blank
86
12.0: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671903-01 and 9671903-02
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
5 1 9671919 D-Silter 6T4 3-12 Assembly Header Box PT Mongoose
6 1 9671954 D-Sander 3-12 Stand w/ Clones Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 12.0.1a – Parts List for 9671903-01
87
12.0.2: Assembly 9671903-02 (Shaker Mongoose PT 3-12/8T4 Mud
Cleaner 3 Mtr. 380V, 50 Hz)
MI-Swaco
Item # Qty: Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
5 1 9671920 D-Silter 8T4 3-12 Assembly Header Box PT Mongoose
6 1 9671954 D-Sander 3-12 Stand w/ Clones Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 12.0.2a – Parts List for 9671903-02
88
12.1: Drawings and Parts List Control Assembly Kit (9671688-02)
A B C D
E 2
11
13
11 15 14 16
2x
7 8 7 8
8 7 9
8 7 ON BOTTOM OF ITEM 2
6 4 5
11 11 8 7
6 4 5 10
8 7 9 12
11 6 5 4 6
11
4 12
5 12
6 4 5
6 4 5
89
12.2: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671843 (Mongoose PT Effluent Skid Less Motors and
Controls)
Applies to main assemblies 9671903-01, -02
90
12.3: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671738-01 (Basket Assembly, Mongoose PT MS Basket
/ 304 SS HDW (Metric)
MI-Swaco
Item # Qty Description
P/N
1 1 9671610 Basket Weldment Mongoose PT
2 1 9671637-02 Cover, Removable Mongoose Flat Panel
3 8 5895001 Wedge Screen Clamping Mongoose 75 Shore D Polyurethane Black
4 36 05-277 Flatwasher M10 Metric, SS
5 28 04-1103 HHCS M10 x 30 Metric, SS
6 28 05-270 Lockwasher M10 Split, SS
7 28 03-229 Hex Nut M10 Metric, SS
8 1 9671638-02 Bar, Skirt Retainer
9 1 5873004 Skirt Mongoose Feed End High Grade Nitrile 80 Shore A
10 4 5837001 Gasket Compression “P” Screen Bed Mongoose
11 4 9671640 Weldment, Screen Gasket Hold Down Bar
12 1 9671925 Drip Lip Basket Mongoose
13 32 07-415 Grommet Screw .273 Sq. Panel Hole, Panel Thk. 0.31-.156
14 32 1441471 Screw Flat HD CRSK Sheet Metal 8-32 x 1” Lg., SS, Sq. Head
15 1 BM6K80100 Label, Crush Hands
Figure 12.3a: Parts List for Assembly 9671738-01
91
12.4: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671919 and 9671920
92
12.4.1: Assembly 9671919 (D-Silter 6T4 3-12 Assembly Header Box
PT Mud Cleaner)
93
12.4.2: Assembly 9671920 (D-Silter 8T4 3-12 Assembly Header Box
PT Mud Cleaner)
94
12.5: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9622220 (Clone Twin 4” Urethane Complete w/ 1/2”
Apex)
2 2
95
12.6: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671954 ( D-Sander 3-12 Stand w/ Clones Mongoose PT
Mud Cleaner)
Applies to main assemblies 9671903-01, -02
96
12.7: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9621280 (Clone Ass’y Urethane 12 in Grooved End )
5
1 6
6
2 3
4
97
12.8: Recommended Spare Parts for Assemblies 9671903-01 and
9671903-02
98
Spare Parts List Continued
99
Spare Parts List Continued
100
12.8.2: Recommended Spare Parts for Assembly 9671903-02
101
Spare Parts List Continued
102
Spare Parts List Continued
103
Page Left Blank
104
13.0: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671904-01 and 9671904-02
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
5 1 9671966 D-Silter 6T4 Assembly Header Box PT Mongoose
6 1 9650360 Nameplate ID Product M-I Swaco
7 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
8 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 13.0.1a – Parts List for 9671904-01
105
13.0.2: Assembly 9671904-02 (Shaker Mongoose PT 8T4 Mud Cleaner
3 Mtr. 380V, 50 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
5 1 9671967 D-Silter 8T4 Assembly Header Box PT Mongoose
6 1 9650360 Nameplate ID Product M-I Swaco
7 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
8 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 13.0.2a – Parts List for 9671904-02
106
13.1: Drawings and Parts List Control Assembly Kit (9671688-02)
A B C D
E 2
11
13
11 15 14 16
2x
7 8 7 8
8 7 9
8 7 ON BOTTOM OF ITEM 2
6 4 5
11 11 8 7
6 4 5 10
8 7 9 12
11 6 5 4 6
11
4 12
5 12
6 4 5
6 4 5
107
13.2: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671843 (Mongoose PT Effluent Skid Less Motors and
Controls)
Applies to main assemblies 9671904-01, -02
108
13.3: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671738-01 (Basket Assembly, Mongoose PT MS Basket
/ 304 SS HDW (Metric)
MI-Swaco
Item # Qty Description
P/N
1 1 9671610 Basket Weldment Mongoose PT
2 1 9671637-02 Cover, Removable Mongoose Flat Panel
3 8 5895001 Wedge Screen Clamping Mongoose 75 Shore D Polyurethane Black
4 36 05-277 Flatwasher M10 Metric, SS
5 28 04-1103 HHCS M10 x 30 Metric, SS
6 28 05-270 Lockwasher M10 Split, SS
7 28 03-229 Hex Nut M10 Metric, SS
8 1 9671638-02 Bar, Skirt Retainer
9 1 5873004 Skirt Mongoose Feed End High Grade Nitrile 80 Shore A
10 4 5837001 Gasket Compression “P” Screen Bed Mongoose
11 4 9671640 Weldment, Screen Gasket Hold Down Bar
12 1 9671925 Drip Lip Basket Mongoose
13 32 07-415 Grommet Screw .273 Sq. Panel Hole, Panel Thk. 0.31-.156
Screw Flat HD CRSK Sheet Metal 8-32 x 1” Lg., SS,
14 32 1441471
Sq. Head
15 1 BM6K80100 Label, Crush Hands
Figure 13.3a: Parts List for Assembly 9671738-01
109
13.4: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671966 and 9671967
110
13.4.1: Assembly 9671966 (6T4 D-Silter/Header Box Assembly
Mongoose PT)
111
13.4.2: Assembly 9671967 (8T4 D-Silter/Header Box Assembly
Mongoose PT)
112
13.5: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9622220 (Clone Twin 4” Urethane Complete w/ 1/2”
Apex)
2 2
113
13.6: Recommended Spare Parts for Assemblies 9671904-01 and
9671904-02
114
Spare Parts List Continued
115
Spare Parts List Continued
116
13.6.2: Recommended Spare Parts for Assembly 9671904-02
117
Spare Parts List Continued
118
Spare Parts List Continued
119
Page Left Blank
120
14.0: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671905-01, 9671905-02, 9671905-03, 9671905-04, and
9671905-05
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671688-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
5 1 9671946 D-Silter Assembly 6T4-212 Header Box PT Mongoose
6 1 9671947 2-12 D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 14.0.1a – Parts List for 9671905-01
121
14.0.2: Assembly 9671905-02 (Shaker Mongoose PT 8T4/2-12 Mud
Cleaner 3 Mtr. 380V, 50 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671975-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
D-Silter Assembly 8T4 Mongoose PT 2-12 Mud Cleaner w/o
5 1 9671930
Flange
6 1 9671947 2-12 D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 14.0.2a – Parts List for 9671905-02
122
14.0.3: Assembly 9671905-03 (Shaker Mongoose PT 6T4/2-12 Mud
Cleaner 3 Mtr. 380V, 50 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671975-02 Control Assembly Kit Mongoose PT (3) Mtr. 380V, 50 Hz
3 2 EM3C00010 Mtr. 1.75 Hp 220-240/380-415V, 50/3/1500
4 1 6905003 Mtr. 220/380V 0.60 Hp 50 Hz XP Vibrator
D-Silter Assembly 6T4 2-12 Header Box
5 1 9671946
Mongoose PT Mud Cleaner
6 1 9671947 2-12 D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 14.0.3a – Parts List for 9671905-03
123
14.0.4: Assembly 9671905-04 (Shaker Mongoose PT 6T4/2-12 Mud
Cleaner 3 Mtr. 440V, 60 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671975-01 Control Assembly Kit Mongoose PT (3) Mtr. 440V, 60 Hz
3 2 EM3C00011 Mtr. 2 Hp 220-240/440-480V, 60/3/1800
4 1 6912002 Mtr. 230/460V 0.60 Hp 60 Hz XP Vibrator
D-Silter Assembly 6T4 2-12 Header Box
5 1 9671946
Mongoose PT Mud Cleaner
6 1 9671947 2-12 D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 14.0.4a – Parts List for 9671905-04
124
14.0.5: Assembly 9671905-05 (Shaker Mongoose PT 8T4/2-12 Mud
Cleaner 3 Mtr. 440V, 60 Hz)
MI-Swaco
Item # Qty Description
P/N
1 1 9671843 Shaker Mongoose PT Effluent Skid Less Motor, Controls
2 1 9671975-01 Control Assembly Kit Mongoose PT (3) Mtr. 440V, 60 Hz
3 2 EM3C00011 Mtr. 2 Hp 220-240/440-480V, 60/3/1800
4 1 6912002 Mtr. 230/460V 0.60 Hp 60 Hz XP Vibrator
D-Silter Assembly 8T4 Mongoose PT 2-12
5 1 9671930
Mud Cleaner w/o Flange
6 1 9671947 2-12 D-Sander Assembly Mongoose PT Mud Cleaner
7 1 9650360 Nameplate ID Product M-I Swaco
8 4 07-409 Pop Rivet 1/8” D 3/16-1/4 Grip, 304 SS
9 2 9671809 Bracket Shipping D-Silter, D-Sander Mongoose PT
Figure 14.0.5a – Parts List for 9671905-05
125
14.1: Drawings and Parts List per Control Assembly Kit Assemblies
9671688-02 and 9671975-01 and 9671975-02
126
14.1.1: Drawings and Parts List Control Assembly Kit 9671688-02
A B C D
E 2
11
13
11 15 14 16
2x
7 8 7 8
8 7 9
8 7 ON BOTTOM OF ITEM 2
6 4 5
11 11 8 7
6 4 5 10
8 7 9 12
11 6 5 4 6
11
4 12
5 12
6 4 5
6 4 5
127
14.1.2: Drawings and Parts List Control Assembly Kit 9671975-01
Applies to main assemblies 9671905-04, -05
CABLE ROUTING 12 13 14 2
D C B A
11
E
10
7 6
6 7
10 12 1
7 9
6 5
10
10
8 4 3
10 4 3 5
10
128
14.1.3: Drawings and Parts List Control Assembly Kit 9671975-02
Applies to main assemblies 9671905-02, -03
CABLE ROUTING 12 13 14 2
D C B A
11
E
10
7 6
6 7
10 12 1
7 9
6 5
10
10
8 4 3
10 4 3 5
10
129
14.2: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671843 (Mongoose PT Effluent Skid Less Motors and
Controls)
130
14.3: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671738-01 (Basket Assembly, Mongoose PT MS Basket
/ 304 SS HDW (Metric)
MI-Swaco
Item # Qty Description
P/N
1 1 9671610 Basket Weldment Mongoose PT
2 1 9671637-02 Cover, Removable Mongoose Flat Panel
3 8 5895001 Wedge Screen Clamping Mongoose 75 Shore D Polyurethane Black
4 36 05-277 Flatwasher M10 Metric, SS
5 28 04-1103 HHCS M10 x 30 Metric, SS
6 28 05-270 Lockwasher M10 Split, SS
7 28 03-229 Hex Nut M10 Metric, SS
8 1 9671638-02 Bar, Skirt Retainer
9 1 5873004 Skirt Mongoose Feed End High Grade Nitrile 80 Shore A
10 4 5837001 Gasket Compression “P” Screen Bed Mongoose
11 4 9671640 Weldment, Screen Gasket Hold Down Bar
12 1 9671925 Drip Lip Basket Mongoose
13 32 07-415 Grommet Screw .273 Sq. Panel Hole, Panel Thk. 0.31-.156
Screw Flat HD CRSK Sheet Metal 8-32 x 1” Lg., SS,
14 32 1441471
Sq. Head
15 1 BM6K80100 Label, Crush Hands
Figure 14.3a: Parts List for Assembly 9671738-01
131
14.4: Drawings and Parts List Mongoose PT Mud Cleaner per
Assemblies 9671946 and 9671930
132
14.4.1: Assembly 9671946 (D-Silter 6T4/2-12 Header Box Mongoose
PT Mud Cleaner)
133
14.4.2: Assembly 9671930 (D-Silter 8T4 Mongoose PT 2-12 Mud
Cleaner without Flange)
134
14.5: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9622220 (Clone Twin 4” Urethane Complete w/ 1/2”
Apex)
2 2
135
14.6: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9671947 (2-12 D-Sander Assembly Mongoose PT Mud
Cleaner)
136
14.7: Drawings and Parts List Mongoose PT Mud Cleaner per
Assembly 9621280 (Clone Assembly Urethane 12 in Grooved End)
5
1 6
6
2 3
4
137
14.8: Recommended Spare Parts for Assemblies 9671905-01,
9671905-02, 9671905-03, 9671905-04, and 9671905-05
138
Spare Parts List Continued
139
Spare Parts List Continued
140
14.8.2: Recommended Spare Parts for Assembly 9671905-02
141
Spare Parts List Continued
142
Spare Parts List Continued
143
14.8.3: Recommended Spare Parts for Assembly 9671905-03
144
Spare Parts List Continued
145
Spare Parts List Continued
146
14.8.4: Recommended Spare Parts for Assembly 9671905-04
147
Spare Parts List Continued
148
Spare Parts List Continued
149
14.8.5: Recommended Spare Parts for Assembly 9671905-05
150
Spare Parts List Continued
151
Spare Parts List Continued
152
Appendix
153
Appendix “A”: Motor Manual
154