Professional Documents
Culture Documents
Mirror
Mirror
PARTS LOCATION
- RR DEF RELAY
- RR DEF FUSE
- ECU-ACC FUSE
- MIR HTR FUSE
B137068E02
MI–2 MIRROR – POWER MIRROR CONTROL SYSTEM
SYSTEM DIAGRAM
E3
Outer Mirror Switch Assembly
I3
Outer Rear View Mirror (LH)
8
from ECU-ACC fuse B
1 5
MH MLH
5 4
MV MLV
2 6
M+ M+
H2
Outer Rear View Mirror (RH)
1 2
MH MRH
5 3
MV MRV
2 7
M+ E
MI
B140703E01
MIRROR – POWER MIRROR CONTROL SYSTEM MI–3
E38 F16
A/C Amplifier Heater Control
Engine Room R/B, J/B Assembly Panel Assembly
RR DEF Relay
H3
I2
5 4
: LIN
B137069E02
MI–4 MIRROR – POWER MIRROR CONTROL SYSTEM
MI
MIRROR – INNER REAR VIEW MIRROR MI–5
PARTS LOCATION
MI
- ECU-ACC FUSE
B137081E01
MI–6 MIRROR – INNER REAR VIEW MIRROR
COMPONENTS
MI
MIRROR – INNER REAR VIEW MIRROR MI–7
SYSTEM DIAGRAM
4
from ECU-IG No. 1 Fuse IG
1
E
C B111209E20
MI
MI–8 MIRROR – INNER REAR VIEW MIRROR
CALIBRATION
1. SELECT COMPASS DISPLAY MODE
(a) The COMP switch allows you to select the Display
or Non-display mode of the compass.
2. SET ZONE
(a) Deviation between the "magnetic north" and "actual
north" differs depending on the location. Therefore,
adjustment of the magnetism is required. Since the
magnetic condition differs depending on the area
where the vehicle is used, it is necessary for each
user to set the zone (Refer to Compass Zone Map).
The zone setting can be changed using the COMP
switch of the inner mirror.
3. PERFORM CALIBRATION
(a) Because each vehicle has its own magnetic field,
calibration should be performed for each vehicle.
This compass function is used when storing the
record of the vehicle's magnetic field.
4. WHEN COMPASS IS MAGNETIZED
(a) A compass could be magnetized during shipping by
vessels or freight cars. Therefore, make sure to
perform calibration and ensure that calibration is
performed properly before delivery. If it cannot be
done (cannot be completed in spite of driving
around several times), it may be caused by
magnetization. Demagnetize the vehicle using a
demagnetizer and perform calibration again.
MI
MIRROR – INNER REAR VIEW MIRROR MI–9
5. SET COMPASS
Normal
Power switch on (IG)
Pressed
Calibration (Step 7)
Leaving it untouched
for a while
MI
Normal Mode
B111243E09
MI
B057087E01
MIRROR – INNER REAR VIEW MIRROR MI–11
REMOVAL
1. REMOVE INNER REAR VIEW MIRROR STAY
HOLDER COVER
(a) Disengage the 2 claws and slide the inner rear view
mirror stay holder cover as shown in the illustration.
B136833
B136834
B136835
MI–12 MIRROR – INNER REAR VIEW MIRROR
INSPECTION
1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY
4 1 (a) Inspect operation of the electrochromic inner mirror.
(1) Connect the positive (+) lead from the battery
to terminal 4 and the negative (-) lead to
terminal 1.
(2) Attach black colored tape to the forward sensor
to prevent it from sensing.
(3) Light up the mirror with an electric light, and
check that the mirror surface changes from
bright to dark.
Standard:
Mirror surface changes from bright to
dark.
If the result is not as specified, replace the
mirror assembly.
MI
B137080E01
INSTALLATION
1. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(a) Using a "TORX" socket wrench (T20), install the
inner rear view mirror with the screw.
Torque: 1.8 N*m (18 kgf*cm, 16 in.*lbf)
(b) Connect the connector.
B136835
B136834
MIRROR – INNER REAR VIEW MIRROR MI–13
(b) Engage the 2 claws and install the inner rear view
mirror stay holder cover as shown in the illustration.
B136841
MI
MIRROR – OUTER REAR VIEW MIRROR MI–13
COMPONENTS
MI
FRONT DOOR LOWER FRAME BRACKET GARNISH
REMOVAL
1. REMOVE FRONT DOOR LOWER FRAME BRACKET
GARNISH (See page ED-41)
2. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
(a) Disconnect the connector.
(b) Remove the 3 nuts.
(c) Disengage the claw and remove the outer rear view
mirror assembly.
B136838
INSPECTION
(A)
1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
RH
(a) Inspect outer mirror motor operation.
(C) (D) (1) Apply battery voltage and check operation of
the mirror face, as shown in the table and
illustration.
(B) Standard
Measurement Condition Specified Condition
M+ MH Battery positive (+) → Terminal 5
(MV)
Turns upward (A)
H- H+ Battery negative (-) → Terminal 2
(M+)
Battery positive (+) → Terminal 2
MV
MI B137078E01
(M+)
Battery negative (-) → Terminal 5
Turns downward (B)
(MV)
Battery positive (+) → Terminal 1
(MH)
Turns left (C)
Battery negative (-) → Terminal 2
(M+)
Battery positive (+) → Terminal 2
(M+)
Turns right (D)
Battery negative (-) → Terminal 1
(MH)
COMPONENTS
MI B146033E01
REPLACEMENT
1. REMOVE OUTER REAR VIEW MIRROR GLASS
(a) Push the upper part of the mirror surface and tilt it.
(b) Using a moulding remover, disengage the 2 claws at
the lower part of the outer rear view mirror, and
Moulding remove the outer rear view mirror glass.
Remover
Protective Tape
B136868E01
B136870
MIRROR – OUTER MIRROR SWITCH MI–17
COMPONENTS
B136891E01
MI
MI–18 MIRROR – OUTER MIRROR SWITCH
REMOVAL
1. REMOVE NO. 1 INSTRUMENT PANEL SUB-
ASSEMBLY (See page IP-12)
2. REMOVE OUTER MIRROR SWITCH ASSEMBLY
(a) Disengage the 2 claws and remove the outer mirror
switch assembly.
B136840
INSPECTION
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) Inspect the outer mirror switch.
(1) Measure the resistance according to the
value(s) in the table below when the switch is
operated.
Standard resistance:
Select "L" on the left/right adjustment
switch
Tester Connection Switch Position Specified Condition
4-8
UP
6-7
4-7
MI 6-8
DOWN
Below 1 Ω
5-8
LEFT
6-7
5-7
RIGHT
6-8
INSTALLATION
1. INSTALL OUTER MIRROR SWITCH ASSEMBLY
(a) Engage the 2 claws and install the outer mirror
switch assembly.
2. INSTALL NO. 1 INSTRUMENT PANEL SUB-
ASSEMBLY (See page IP-34)
B136840
MI