Professional Documents
Culture Documents
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-30
MD-31
Fuses and Detection Points(Machines with Serial Numbers Power Fuse-Equipped Fuse Blown-Fuse
Target for Protection
50001 or Those Later than 50001) Supply Component No. Detection Circuit
B161 Pulse motor: MC1
Power Fuse-Equipped Fuse Blown-Fuse Target for Protection
Supply Component No. Detection Circuit B171 Pulse motor: MC2
(1.6A) - B181 Pulse motor: MC3
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-31
MD-32
Fuses and Detection Points(Machines with Serial Numbers Power Fuse-Equipped Fuse Blown-Fuse
Target for Protection
Supply Component No. Detection Circuit
60001 or Those Later than 60001)
B161 Pulse motor: MC1
Power Fuse-Equipped Fuse Blown-Fuse Target for Protection B171 Pulse motor: MC2
Supply Component No. Detection Circuit
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-32
MD-33
Overcurrent Protection Circuit Block Diagram(Machines with
Serial Numbers 20001 or Those Later than 20001)
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-33
MD-34
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-34
MD-35
Overcurrent Protection Circuit Block Diagram(Machines with
Serial Numbers 50001 or Those Later than 50001)
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-35
MD-36
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-36
MD-37
Overcurrent Protection Circuit Block Diagram(Machines with
Serial Numbers 60001 or Those Later than 60001)
Power supply board
PSU29A
TP1 FR9H1304_E.ai
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-37
MD-38
3A +15V(F) 1.6A
1.6A Start-piont
-15V detection board
1.5A -15V(H)
Image 1.6A SYN12A
processing board
AUX12V +12V IMG17A/B
+5V(S) 1.6A
TP1
CPU board
CPU91A
1.6A IP leading-edge detection board : SED23A
FR9H1305.ai
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-38
MD-39
3.2 Erasure Unit Control 3.2.2 Components of the Erasure Unit Control (#20001 or later)
- The control circuit for the erasure lamp unit is located on the SNS17B board. A
3.2.1 Overview of the Erasure Unit Control control signal from the SNS17B board causes the relay circuit and lamp inverter
circuit of the driver board (INV17A/B) to operate, thereby turning ON or OFF the
(#20001 or later) lamps and fans.
The erasure unit provides idle illumination control, IP erasure control, and fan control. - To enable discrimination between failures of the control board (SNS17A) and driver
board (INV17A/B), LEDs are provided on the SNS17B board to indicate the status
Feature: Erasure unit initialization is effected after verifying that the machine is of the control signal.
emptied of IPs.
{MD:3.3.3_Correspondence between LEDs and Erasure Control Signals and
Idle illumination control FFM Control Signals}
To obtain an adequate lamp light intensity for IP erasure after RU power ON, lamp
(LAMP1 - LAMP5) illumination and erasure unit cooling fan (FANE1) operation are Power supply unit
controlled so as to maintain a constant temperature inside the erasure unit. PSU17A
+5V(A) +24V(E)
CN1 CN2
IP erasure control
To effect IP erasure, the erasure unit pass time is controlled in accordance with the Sensor board CN20
dose received by a processed IP. SNS17B FANE3 FANE2 LAMP2
Safety CN5
TSWE1 FANE1 LAMP1 LAMP3
Fan control thermostat
control circuit CN9 CN7 CN6 CN3 CN4 CN5
Control is exercised so as to operate the erasure unit cooling fan (FANE1) when the
temperature inside the erasure unit is high. LED F4 F1 F2 F3
Temperature adjustment control Lamp
CN2 Relay CN1
- The heat generated during lamp (LAMP1 - LAMP5) illumination is detected by the inverter
Lamp circuit
temperature thermistor (THE1) and used to exercise control of the erasure unit CN16 circuit
cooling fan (FANE1) operation and lamp illumination. temperature
control circuit Inverter board
- While the machine is idle and processing no IP, control is exercised to automatically INV17A CN8
illuminate the lamps for temperature adjustment purposes. Unlit lamp
detection
- Before the lamps are illuminated, they are subjected to preheating. circuit CN6
Inverter board
Temperature INV17B
control fan Lamp
(FANE1) CN2 Relay CN1
circuit inverter
control circuit circuit F1 F2
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-39
MD-40
3.2.3 Overview of the Erasure Unit Control Control regarding service life of the lamp
(#50001 or later) - When the illumination count of the erasure lamp approaches the assumed machine
working hours, a warning “It’s about time to replace” is issued.
Temperature adjustment control - When the illumination count of the erasure lamp reaches the assumed machine
Temperature adjustment control is exercised to keep the inside of the erasure unit at a working hours, a warning “The fluorescent lamp reaches the end of life. Contact the
service for replacement” is issued.
constant temperature by controlling the operation of the erasure cooling fan (FANB1)
in orderto obtain adequate light intensity required for IP erasure after the RU power is - When the illumination count of the erasure lamp exceeds the assumed machine
turned ON. working hours, a warning “The erasure cannot be guaranteed” is issued.
IP erasure control
Erasure unit pass time is controlled in accordance with the dose received by a read IP,
and the IP is erased.
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-40
MD-41
3.2.4 Components of the Erasure Unit Control
(#50001 or later)
The control circuit for the erasure lamp unit is located on the ERS23A board. A control
signal from the ERS23A board causes lamp inverter circuit to operate, thereby turning
ON or OFF the lamps.
LAMPB4, 6 LAMPB3, 5
011-201-11E
06.29.2012 FM6046
CR-IR 362 Service Manual MD-41