Professional Documents
Culture Documents
Quiz 4: Torsion
Q.1
A bar with a channel (C) cross-section (as shown in Fig) is subjected to pure torsion with equal and
opposite torsional moments at the ends such that the bar is in equilibrium. There are no end-
restraints applied on the bar. Consider an arbitrary point P located, say, at the mid-span of the bar (Z-
axis) and in the web of the C-section (X and Y axes as shown in Fig). Then, as per the assumptions
for torsion problems discussed in class, the stress state at P is such that the following stress(es)
is(are) equal to zero.
τxy
τyz
σyy
σzz
Q.2
https://hello.iitk.ac.in/ae331a21/#/result/73 1/6
11/12/21, 8:20 PM AE331A: Introduction To Aerospace Structures
A bar of triangular cross-section shown in figure is subjected to pure torsion with no end restraints. If
the Prandtl’s stress function f(x,y) can be written in the form f1(x,y)*f2(x,y)*f3(x,y), then the function
which is NOT f1, f2 or f3 is
x+y-a
x-y
Q.3
A bar with an L-section (as shown in Fig) is subjected to pure torsion with equal and opposite
torsional moment T at the ends such that the bar is in equilibrium. There are no end-restraints
applied on the bar. Ignore the higher order effects. If T = 1000 Nm, the maximum shear stress is
_____ MPa
Your answer:
200
Correct answer:
200
Q.4
https://hello.iitk.ac.in/ae331a21/#/result/73 2/6
11/12/21, 8:20 PM AE331A: Introduction To Aerospace Structures
A bar with an L-section (as shown in Fig) is subjected to pure torsion with equal and opposite
torsional moment T at the ends such that the bar is in equilibrium. There are no end-restraints
applied on the bar. Ignore the higher order effects. If T = 1000 Nm, and G = 20 GPa, the twist per unit
length is ____ (rad/m).
Your answer:
Correct answer:
Q.5
A bar having a cross-section of an equilateral triangle with sides of length ‘b’ and height ‘h’ (as in
figure) is subjected to pure torsion T with no end restraints. If the polar moment of inertia of the
15√3 T
cross-section, Ip is 1
b
4
and the twist per unit length is 4
, where G is the shear modulus,
16√3 Gh
https://hello.iitk.ac.in/ae331a21/#/result/73 3/6
11/12/21, 8:20 PM AE331A: Introduction To Aerospace Structures
AE331A:
Introduction To Aerospace Structures
Users Online : 2
Q.6
A thin-walled Z section shown in the figure above is subjected a shear load 1000 N in the positive y-
direction applied through the shear centre of the section. The wall thickness is uniformly 1 mm. The
shear flow at point A is ________ N/m
Your answer:
Correct answer:
Q.7
https://hello.iitk.ac.in/ae331a21/#/result/73 4/6
11/12/21, 8:20 PM AE331A: Introduction To Aerospace Structures
A thin-walled Z section shown in the figure above is subjected a shear load 1000 N in the positive y-
direction applied through the shear centre of the section. The wall thickness is uniformly 1 mm. The
shear flow at point B is ________ N/m.
Your answer:
Correct answer:
4200
Q.8
A thin-walled Z section shown in the figure above is subjected a shear load 1000 N in the positive y-
direction applied through the shear centre of the section. The wall thickness is uniformly 1 mm. The
shear flow at point C is ________ N/m.
Your answer:
12750
Correct answer:
https://hello.iitk.ac.in/ae331a21/#/result/73 5/6
11/12/21, 8:20 PM AE331A: Introduction To Aerospace Structures
12750
AE331A: Introduction To Aerospace Structures
Users Online : 2
Score: 8
https://hello.iitk.ac.in/ae331a21/#/result/73 6/6