Professional Documents
Culture Documents
83
www.hilti.co.uk
Company: Robbin Engineering Page: 1
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Specifier's comments:
1 Anchor Design
1.1 Input data
Baseplate
CBFEM
: lx x ly x t = 100.0 mm x 150.0 mm x 15.0 mm;
CBFEM
- The anchor calculation is based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 2
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Anchor forces are calculated based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 3
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
N
NEd £ NRd,s = Rk,s EN 1992-4, Table 7.1
gM,s
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 4
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
N
NEd £ NRd,p = Rk,p EN 1992-4, Table 7.1
gM,p
0 Ap,N
NRk,p = NRk,p · 0
· y g,Np · y s,Np · y re,N · y ec1,Np · y ec2,Np EN 1992-4, Eq. (7.13)
Ap,N
0
NRk,p = y sus · t Rk · p · d · hef EN 1992-4, Eq. (7.14)
y sus =1 EN 1992-4, Eq. (7.14a)
Rk,c
³ 1.00 EN 1992-4, Eq. (7.18)
k3
t Rk,c = · √hef · fck EN 1992-4, Eq. (7.19)
p·d
c
y s,Np = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.20)
ccr,Np £
1
y ec1,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec1,N £
1+ (
scr,Np )
1
y ec2,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec2,N £
1+ (
scr,Np )
2 0 2 2 2
Ap,N [mm ] Ap,N [mm ] t Rk,ucr,20 [N/mm ] scr,Np [mm] ccr,Np [mm] cmin [mm] fc,cyl [N/mm ]
167,860 138,128 18.00 371.7 185.8 ∞ 25.00
0
yc t Rk,cr [N/mm ]
2
k3 t Rk,c [N/mm ]
2
y g,Np y g,Np
1.023 8.69 7.700 12.25 1.167 1.089
Group anchor ID
1, 2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 5
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
N
NEd £ NRd,c = Rk,c EN 1992-4, Table 7.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.4)
ccr,N £
1
y ec1,N = 1.00 EN 1992-4, Eq. (7.6)
2 · eN,1 £
1+ (
scr,N )
1
y ec2,N = 1.00 EN 1992-4, Eq. (7.6)
2 · eN,2 £
1+ (
scr,N )
z
y M,N = 2.0 - 1.00 EN 1992-4, Eq. (7.7)
1.5 · hef ³
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] fc,cyl [N/mm ]
221,184 186,624 216.0 432.0 25.00
Group anchor ID
1, 2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 6
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
V
VEd £ VRd,s = Rk,s EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
33.500 1.000 33.500 1.250 26.800 2.484
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 7
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
V
VEd £ VRd,cp = Rk,cp EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · min {NRk,c; NRk,p} EN 1992-4, Eq. (7.39c)
0 A
NRk,p = NRk,p · 0p,N · y g,Np · y s,Np · y re,N · y ec1,Np · y ec2,Np EN 1992-4, Eq. (7.13)
Ap,N
0
NRk,p = y sus · t Rk · p · d · hef EN 1992-4, Eq. (7.14)
y sus =1 EN 1992-4, Eq. (7.14a)
scr,Np = 7.3 · d · √y sus · t Rk £ 3 · hef EN 1992-4, Eq. (7.15)
0,5
y g,Np
0
= y g,Np - (s s )
cr,Np
· (y g,Np - 1) ³ 1.00
0
EN 1992-4, Eq. (7.17)
1,5
0
y g,Np = √n - (√n - 1) · (tt ) Rk
Rk,c
³ 1.00 EN 1992-4, Eq. (7.18)
k3
t Rk,c = · √hef · fck EN 1992-4, Eq. (7.19)
p·d
c
y s,Np = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.20)
ccr,Np £
1
y ec1,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec1,N £
1+ (
scr,Np )
1
y ec2,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec2,N £
1+ (
scr,Np )
2 0 2 2 2
Ap,N [mm ] Ap,N [mm ] t Rk,ucr,20 [N/mm ] ccr,Np [mm] scr,Np [mm] cmin [mm] fc,cyl [N/mm ]
83,930 138,128 18.00 185.8 371.7 ∞ 25.00
0
yc t Rk,cr [N/mm ]
2
k3 t Rk,c [N/mm ]
2
k8 y g,Np
Group anchor ID
2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 8
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
1.5 Combined tension and shear loads (EN 1992-4, Section 7.2.3)
Steel failure
a a
bN + bV £ 1.0
Concrete failure
1.6 Warnings
• The anchor design methods in PROFIS Engineering require rigid baseplates as per current regulations (ETAG 001/Annex C, EOTA TR029,
etc.). This means load re-distribution on the anchors due to elastic deformations of the baseplate are not considered - the baseplate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering calculates the
minimum required baseplate thickness with CBFEM to limit the stress of the baseplate based on the assumptions explained above. The
proof if the rigid base plate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be checked for
agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• Drilled hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice,
blow twice with oil-free compressed air (min. 6 bar)).
• Characteristic bond resistances depend on short- and long-term temperatures.
• Edge reinforcement is not required to avoid splitting failure
• The anchor design methods in PROFIS Engineering require rigid baseplates, as per current regulations (AS 5216:2021, ETAG 001/Annex
C, EOTA TR029 etc.). This means that the baseplate should be sufficiently rigid to prevent load re-distribution to the anchors due to
elastic/plastic displacements. The user accepts that the baseplate is considered close to rigid by engineering judgment."
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 9
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Hilti AM threaded rod with HIT-HY 200 injection mortar with 144 mm embedment h_ef, M12, Steel galvanized, Hammer drilling installation per
ETA 11/0493
y
50.0 50.0
40.0
75.0
2
67.5
80.0
x
75.0
1
30.0
50.0 50.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 10
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
2 Baseplate design
2.2 Summary
Description Profile Baseplate Concrete [%]
sEd [N/mm²] ePl [%] sEd [N/mm²] ePl [%] Hole bearing [%]
1 Combination 1 275.62 0.30 235.32 0.15 2 133
2.3 Baseplate plate classification
Results below are displayed for the decisive load combinations: Combination 1
Anchor tension forces Equivalent rigid baseplate (CBFEM) Component-based Finite Element Method
(CBFEM) baseplate
Anchor 1 17.644 kN 9.164 kN
Anchor 2 18.877 kN 28.278 kN
User accepted to consider the selected baseplate as rigid by his/her engineering judgement. This means the anchor design guidelines can be
applied.
2.4 Profile/Stiffeners/Plate
Profile and stiffeners are verified at the level of the steel to concrete connection. The connection design does not replace the steel design for
critical cross sections, which should be performed outside of PROFIS Engineering.
Results
Part Load Material sEd [N/mm²] ePl [%] fy [N/mm²] gM0 fy/gM0 elim [%] Status
combination [N/mm²]
Plate Combination S 235 235.32 0.15 235.00 1.00 235.00 5.00 OK
1
Profile Combination S 275 275.62 0.30 275.00 1.00 275.00 5.00 OK
1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 11
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
275.00 N/mm²
0.00 N/mm²
2.4.1.2 Plastic strain
Results below are displayed for the decisive load combination: 1 - Combination 1
5.00%
0.00%
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 12
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Equations
k1 ab fu d t
Fb,Rd =
gM2
VEd
Utilisation =
Fb,Rd
Variables
k1 ab fu [N/mm²] d [mm] t [mm] gM2
Anchor 1 2.50 1.00 360.00 12.0 15.0 1.25
Anchor 2 2.50 1.00 360.00 12.0 15.0 1.25
Results
VEd [kN] Fb,Rd [kN] Utilisation [%] Status
Anchor 1 0.984 129.600 1 OK
Anchor 2 2.484 129.600 2 OK
2.5 Concrete
Decisive load combination: 1 - Combination 1
According to EN1992-1-1 section 6.7(4), the concrete should have sufficient reinforcement to take into account the tensile forces that develop
due to the fixture attachment. The definition of the reinforcement in the concrete is not within the scope of PROFIS Engineering.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
12
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 13
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
0.00 N/mm²
2.5.2 Verification of compression in concrete under the baseplate around the profile as per EN1992-1 section 6.7 and EN1993-1-8,
section 6.2.5
Equations
fjd
bj kj acc fck
=
gc
N
s = Aeff
Utilisation =
s
fjd
Variables
N [kN] Aeff [mm²] bj kj acc fck [N/mm²] gc
38.760 1,027 0.67 3.00 0.85 25.00 1.50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
13
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 14
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Results
s [N/mm²] fjd [N/mm²] Utilisation [%] Status
37.75 28.48 133 NOT OK
2.7 Warnings
● By using the CBFEM calculation functionality of PROFIS Engineering you may act outside the applicable design codes and your specified
baseplate may not behave rigidly. Please, have the results validated by a professional designer and/or structural engineer to ensure
suitability and adequacy for your specific jurisdiction and project requirements.
● The anchor is modelled considering stiffness values determined from load displacement curves tested in an independent laboratory.
Please note that no simple replacement of the anchor is possible as the anchor stiffness has a major impact on the load distribution
results.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
14
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 15
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
3 Summary of results
Design of the baseplate, anchor, welds and other elements are based on CBFEM (component based finite element method) and Eurocode
regulations.
Load combination Max. utilisation Status
Anchors Combination 1 100% OK
Baseplate Combination 1 100% OK
Concrete Combination 1 133% NOT OK
Profile Combination 1 100% OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
15
Hilti PROFIS Engineering 3.0.83
www.hilti.co.uk
Company: Robbin Engineering Page: 16
Address: Specifier: Marcelo Ferreira
Phone I Fax: | E-Mail:
Design: Concrete - 2 Feb 2023 Date: 02/02/2023
Fastening Point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
16