Professional Documents
Culture Documents
INSTRUCTION: Select the correct answer for each of the following questions. Mark
only one answer for each item by shading the box corresponding to the letter of
your choice on the answer sheet provided.
15. What is the ideal fixture that you would position adjacent to toilet
blocks and wet areas, and provide facilities for cleaning staff the maintain
area?
A. Slop-hopper
B. Drinking fountain
C. Cleaner’s Sink
D. Pan room sink
16. Grease interceptor shall be at all times be _______ for inspection,
cleaning and removal of grease.
A. Open
B. Labeled with instructions
C. Easily accessible
D. Documented by the manufacturer
17. Which is that clarifier device with at least three (3) cubic meters
capacity designed and installed to retain and separate grease serving, one or
more fixtures which are remotely located?
A. Grease trap
B. Grease Receptacle
C. Grease receptor
D. Grease Interceptor
18. In plan 9, identify b item A.
A. Horizontal Safety Valve
B. Horizontal Double Disc Arc Gate Valve
C. Wedge Shape Disc Gate Valve
D. Double disc arc gate valve
19. A refrigerator used to store food and that requires drainage shall be
drained by means of____________.
A. a direct connection
B. an approved air gap fitting
C. an indirect waste pipe
D. no drain required
20. In plan 9, identify a in item C.
A. Safety valve
B. Conventional type angle valve
C. Angle valve
D. Composition type angle valve
21. Remove burrs from the inside ends of a galvanized pipe with a __________.
A. Reamer B. knife C. hacksaw D. pipe cutter
22.What tool is a long flexible rod up to 200 feet long, used to insert into
a sewer line for cleaning and declogging.
A. Plumber’s Rod
B. Plumber’s line
C. Plumber’s Roll
D. Plumber’s one-piece flat sewer tape
23. Identify the tool labelled e in Plate 4.
A. D Handle, steel scoop shovel
B. D Handle, round point spade
C. D handle, trench shovel
D. D Handle, Drain spade
24. Which wrench has a doublejaw which gives fast, ratchet-like action in
either direction?
A. Wooden stakes
B. A Firm Bed
C. Concrete Blocks
D. Common bricks
34. Which is the most probable cause for bathubs that won’t hold water?
A. Leaking trap
B. Defective strainer
C. Vent Blockages
36. For a water supply system, if there is too much pressure at the supply
main, what should be installed in the system?
37. When it takes more soap and water to clean the laundry, the water is
________.
39. All holding tank drain connections shall be provided with a ________.
A. Two-way valve
B. Backflow Device
C. Sanitary Valve
D. Backwater valve
41. For aging water distribution pipes in a building whose leaks are
inaccessible for repair, what will you recommend?
A. Re-pipe the whole water distribution system with better suitable pipes.
42. In using chemicals to open drains, while it is a lot less messy and less
troublesome compared to force pumps or snakes, chemicals _____________ leave
dangerous mixtures of alkali and acid in the drain pipe.
43. What would cause the stoppage if hot water is constantly used to clear
clog?
44. In using chemical to clear clogs, when working with chemicals, mixing
acid with alkali will produce a minor explosion that will drive the
combination ouit of the drain pipe into the room. This is ________.
A. Inside a room
B. Proper ventilation
C. Frequently used
47. Per DOLE Safety and Health in plumbing workplace; there are four types of
hazards. During construction, one is chemical hazards and it include hazards
from __________.
A. Sewage
B. Liquid waste
C. Effluent
48. Per DOLE Safety and health in the plumbing workplace, there are four
types of hazards. During construction, one is physical hazards and it include
hazards from _________.
D. Prolonged standing
49. Plate 10 is the matrix schedule for the computation of the water bills of
a certain water utility supplier (water district). If the concessionaire
consumption for a 1” inch service pipe for industrial is 58 cu.m, how much is
the water bill for the month?
50. This is a seldom occurrence of seal lost in the drainage system and this
is caused by the suspension of foreign objects; such as strings, rags, etc.;
into the trap seal extending over the outlet arm of the trap. This is called
________.
A. Back pressure
B. Capillary action
C. Vacuum
D. Siphonage
51. The loss of the trap seal due to a minus pressure or negative pressure in
the drainage system is called________.
A. Back pressure
B. Vacuum
C. Siphonage
D. Evaporation
52. When a caulking iron had stricken hard a cast iron hub while doing caulk
joint and had the pipe cracked, what would you do?
A. Proceed in caulking, anyway the oakum and pouring lead will cover the
crack
53. In a water distribution system, what connects the water main to the water
risers?
SITUATIONAL
Situation 1- In Plan 3
A. Water stop
B. Corporation cock
C. Curb stop
D. Stop cock
D. Bronze Nipple
Situation 2- Plan 8
B. Branch vent
C. Group Vent
D. Loop vent
Situation 3- Plate 1
A. 3” sanitary tee,minimum
B. 3” tee, minimum
C. 4” tee, minimum
B. Hand hole
C. Access hole
D. Manhole
Situation 4- Plan 6
A. 30 to 200 cm
B. 10 to 25 cm
C. 0.50 m to 1.00 m
D. 300 to 400 cm
B. Waste branch
C. Soil/waste branch
D. Soil branch
Situation 5- Detail 2
D. Check Valve
Situation 6- In plate 9
D. Adapter
A. 90 ½ GENERAL ELBOW
B. ~ Street bend
C. 90 ½ street elbow
81. Determine the minimum number of water closet for male comfort rooms of a
college campus with 1000 males.
A. 35 B. 20 C. 30 D. 25
82. Determine the minimum number of water closet for the female comfort rooms
of a college campus with 1200 females.
A. 42 B. 40 C. 45 D. 35
83. Determine the minimum number of urinals for the male comfort rooms of a
college campus with 1000 males.
A. 29 B. 35 C. 30 d. 25
84. Determine the minimum number of lavatories for the male comfort rooms of
a college campus with 1000 males.
A. 20 B. 35 C. 30 D. 25
85. Determine the minimum number of lavatories for the female comfort rooms
of a college campus with 1200 females.
A. 45 B. 42 C. 40 D.35
Situation 8- FIGURE 12
D. Pipe Cutter
C. Pipe cutter
B. Pipe cutter
C. Muffler cutter
A. Lever bender
B. Ratchet bender
D. Hydraulic benders
A. 457.2mm (18”)
B. 914.4mm (36”)
C. 304.8mm (12”)
D. 355.6mm (14”)
A. 914.4mm (36”)
B. 609.4 (24”)
C. 508.0mm (20”)
D. 457.2mm (18”)
A. 457.2mm (18”)
B. 355.6mm (14”)
C. 304.8mm (12”)
D. 254.0mm (10”)