Professional Documents
Culture Documents
FM/AM
Compact Disc Player
Operating Instructions US
Mode d’emploi FR
Owner’s Record
The model and serial numbers are located on the bottom of the unit.
Record these numbers in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. Serial No.
CDX-GT510
CDX-GT51W
© 2006 Sony Corporation
For installation and connections, see the The “SAT Radio Ready”
supplied installation/connections manual. logo indicates that this
product will control a
satellite radio tuner module
(sold separately). Please see your nearest
Warning authorized Sony dealer for details on the
satellite radio tuner module.
This equipment has been tested and found to “SAT Radio,” “SAT Radio Ready,” the SAT
comply with the limits for a Class B digital Radio and SAT Radio Ready logos and all
device, pursuant to Part 15 of the FCC Rules. related marks are trademarks of Sirius Satellite
These limits are designed to provide reasonable Radio Inc. and XM Satellite Radio Inc.
protection against harmful interference in a
residential installation. This equipment SonicStage and its logo are trademarks of Sony
generates, uses, and can radiate radio frequency Corporation.
energy and, if not installed and used in “ATRAC” and its logo are trademarks of Sony
accordance with the instructions, may cause Corporation.
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this Microsoft, Windows Media,
equipment does cause harmful interference to and the Windows logo are
radio or television reception, which can be trademarks or registered
determined by turning the equipment off and on, trademarks of Microsoft
the user is encouraged to try to correct the Corporation in the United States and/or other
interference by one or more of the following countries.
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
2
Table of Contents
3
Welcome ! Getting Started
Thank you for purchasing this Sony Compact Resetting the unit
Disc Player. You can enjoy your drive with the
following functions. Before operating the unit for the first time, or
• CD playback after replacing the car battery or changing the
You can play CD-DA (also containing CD connections, you must reset the unit.
TEXT*), CD-R/CD-RW (MP3/WMA/AAC Detach the front panel and press the RESET
files also containing Multi Session (page 13)) button with a pointed object, such as a ball-point
and ATRAC CD (ATRAC3 and ATRAC3plus pen.
format (page 14)).
Type of discs Label on the disc
RESET
button
CD-DA
Note
Pressing the RESET button will erase the clock setting
and some stored contents.
MP3
WMA
AAC Preparing the card remote
ATRAC CD commander
Before using the card remote commander for the
• Radio reception first time, remove the insulation film.
– You can store up to 6 stations per band (FM1,
FM2, FM3, AM1 and AM2).
– BTM (Best Tuning Memory): the unit selects
strong signal stations and stores them.
• Sound adjustment
– EQ3 stage2: You can choose any one of 7
preset equalizer curves.
– DSO (Dynamic Soundstage Organizer):
creates a more ambient sound field, using
virtual speaker synthesis, to enhance the
sound of speakers, even if they are installed Setting the clock
low in the door.
The clock uses a 12-hour digital indication.
• Optional unit operation
You can also control optional CD/MD 1 Press and hold the select button.
changers. The setup display appears.
• Auxiliary equipment connection
An AUX input jack on the front of the unit 2 Press the select button repeatedly
allows connection of a portable audio device. until “CLOCK-ADJ” appears.
* A CD TEXT disc is a CD-DA that includes
3 Press (SEEK) +.
information such as disc, artist and track name. The hour indication flashes.
4 Rotate the volume control dial to set
the hour and minute.
To move the digital indication, press (SEEK)
–/+.
5 Press the select button.
The setup is complete and the clock starts.
To display the clock, press (DSPL). Press
(DSPL) again to return to the previous display.
With the card remote commander
In step 4, to set the hour and minute, press M or m.
4
Detaching the front panel Attaching the front panel
Place the hole A of the front panel onto the
You can detach the front panel of this unit to spindle B on the unit, then lightly push the left
prevent theft. side in.
Press (SOURCE) on the unit (or insert a disc) to
Caution alarm operate the unit.
If you turn the ignition switch to the OFF
position without detaching the front panel, the
caution alarm will sound for a few seconds. A
The alarm will only sound if the built-in
amplifier is used. B
1 Press (OFF).
The unit is turned off.
2 Press (OPEN).
The front panel is flipped down.
c
3 Slide the front panel to the right, then
gently pull out the left end of the front
panel.
Note
Do not put anything on the inner surface of the front
panel.
5
Location of controls and basic operations
Main unit
12 3 4 5 67
DSO SOURCE
AUX
SEEK SEEK
EQ3 MODE
CAT GP/ALBM REP SHUF PAUSE
BTM DSPL 1 2 3 4 5 6 SCRL
CDX-GT510
CDX-GT51W
8 9 q; qa qs qd qf qg
Front panel removed
qh qj qk
RESET
Card remote commander Refer to the pages listed for details. The
corresponding buttons on the card remote
RM-X151 commander control the same functions as those
on the unit.
1 OFF ATT
wa A OFF button
4 ws To power off; stop the source.
SOURCE SEL MODE
ql qs B DSO button 4
To select the DSO mode (1, 2, 3 or OFF).
+ The larger the number, the more enhanced
the effect.
wd
– C Volume control dial/select button 9
qg To adjust volume (rotate); select setup items
qd DSPL SCRL
(press and rotate).
1 2 3
D SOURCE button
4 5 6
wf To power on; change the source (Radio/CD/
MD*1/AUX/SAT*2).
+ E Display window
w; VOL
–
F AUX input jack 10
To connect a portable audio device.
6 G OPEN button 5
H EQ3 (equalizer) button 9 The following buttons on the card remote
To select an equalizer type (XPLOD, commander have also different buttons/functions
VOCAL, EDGE, CRUISE, SPACE, from the unit. Remove the insulation film before
GRAVITY, CUSTOM or OFF). use (page 4).
I Receptor for the card remote ql < (.)/, (>) buttons
commander To control CD/radio, the same as (SEEK)
–/+ on the unit.
J SEEK –/+ buttons
CD: w; VOL (volume) +/– button
To skip tracks (press); skip tracks To adjust volume.
continuously (press, then press again within wa ATT (attenuate) button
about 1 second and hold); reverse/fast- To attenuate the sound. To cancel, press
forward a track (press and hold). again.
Radio:
To tune in stations automatically (press); find ws SEL (select) button
a station manually (press and hold). The same as the select button on the unit.
K BTM/CAT*2 button 8 wd M (+)/m (–) buttons
To start the BTM function (press and hold). To control CD, the same as (1)/(2)
L MODE button 8, 11 (GP/ALBM –/+) on the unit.
To select the radio band (FM/AM); select the wf Number buttons
SAT tuner band (mode)*2; select the unit*3. To receive stored stations (press); store
M DSPL (display) button 8 stations (press and hold).
To change display items. *1 When an MD changer is connected.
*2 When the SAT tuner is connected.
N Number buttons *3 When a CD/MD changer is connected.
CD/MD*1: *4 When an ATRAC CD is played.
(1)/(2): GP*4/ALBM*5 –/+ *5 When an MP3/WMA/AAC is played.
To skip albums (press); skip albums *6 If the changer is connected, the operation is
different, see page 11.
continuously (press and hold).*6 *7 When playing back on this unit.
(3): REP 8, 11
(4): SHUF 8, 11 Note
(6): PAUSE*7 If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
To pause playback. To cancel, press unless (SOURCE) on the unit is pressed, or a disc is
again. inserted to activate the unit first.
Radio:
To receive stored stations (press); store Tip
For details on how to replace the battery, see
stations (press and hold). “Replacing the lithium battery of the card remote
O SCRL (scroll) button 8 commander” on page 14.
To scroll the display item.
P RESET button 4
Q Z (eject) button 5
To eject the disc.
R Disc slot 5
To insert the disc.
7
CD Radio
For details on selecting a CD/MD changer, see Storing and receiving stations
page 11.
Caution
Display items When tuning in stations while driving, use Best
Tuning Memory (BTM) to prevent an accident.
Storing manually
Repeat and shuffle play
1 While receiving the station that you
1 During playback, press (3) (REP) or want to store, press and hold a
(4) (SHUF) repeatedly until the number button ((1) to (6)) until
desired setting appears. “MEM” appears.
The number button indication appears in the
Select To play display.
TRACK track repeatedly. Note
If you try to store another station on the same number
ALBUM*1 album repeatedly. button, the previously stored station will be replaced.
GROUP*2 group repeatedly.
SHUF ALBUM* 1 album in random order. Receiving the stored stations
SHUF GROUP*2 group in random order. 1 Select the band, then press a number
SHUF DISC disc in random order. button ((1) to (6)).
*1 When an MP3/WMA/AAC is played.
*2 When an ATRAC CD is played.
8
Tuning automatically Other functions
1 Select the band, then press (SEEK) –/+ Changing the sound settings
to search for the station.
Scanning stops when the unit receives a
station. Repeat this procedure until the Adjusting the sound
desired station is received.
characteristics — BAL/FAD/SUB
Tip You can adjust the balance, fader, and subwoofer
If you know the frequency of the station you want to
listen to, press and hold (SEEK) –/+ to locate the
volume.
approximate frequency, then press (SEEK) –/+ 1 Press the select button repeatedly
repeatedly to fine adjust to the desired frequency
(manual tuning).
until “BAL,” “FAD” or “SUB” appears.
The item changes as follows:
LOW*1 t MID*1 t HI*1 t
BAL (left-right) t FAD (front-rear) t
SUB (subwoofer volume)*2 t AUX*3
*1 When EQ3 is activated (page 9).
*2 When the audio output is set to “SUB”
(page 10).
“ATT” is displayed at the lowest setting, and can
be adjusted up to 20 steps.
*3 When AUX source is activated (page 10).
2 Rotate the volume control dial to
adjust the selected item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
With the card remote commander
In step 2, to adjust the selected item, press <, M, ,
or m.
10
Skipping albums and discs
1 During playback, press (1)/(2) (GP/ALBM
AUX –/+).
Press (1)/(2) (GP/ALBM
To skip
–/+)
album and release (hold for a
AUX moment).
album within 2 seconds of first
continuously releasing.
discs repeatedly.
discs then, press again within 2
Connecting cord* continuously seconds and hold.
(not supplied)
SEL DSPL
MODE MODE
DSPL SEL
Disc number
Playback starts. continue to next page t
11
Location of controls
The corresponding buttons on the rotary Additional Information
commander control the same functions as those
on this unit. Precautions
ATT • If your car has been parked in direct sunlight,
SEL
allow the unit to cool off before operating it.
PRESET/ • Power antenna (aerial) will extend automatically
DISC while the unit is operating.
MODE
Moisture condensation
SOURCE On a rainy day or in a very damp area, moisture
OFF
DSPL condensation may occur inside the lenses and
display of the unit. Should this occur, the unit will
VOL SEEK/AMS OFF not operate properly. In such a case, remove the disc
The following controls on the rotary commander and wait for about an hour until the moisture has
require a different operation from the unit. evaporated.
To decrease
If you need to mount the rotary commander on
the right hand side of the steering column, you
can reverse the operative direction.
• Do not use any discs with labels or stickers
1 While pushing the VOL control, press and
attached.
hold (SEL). The following malfunctions may result from using
such discs:
– Inability to eject a disc (due to a label or sticker
peeling off and jamming the eject mechanism).
– Inability to read audio data correctly (e.g.,
playback skipping, or no playback) due to heat
shrinking of a sticker or label causing a disc to
warp.
• Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this unit.
Attempting to do so may damage the unit. Do not
use such discs.
• You cannot play 8 cm (3 1/4 in) CDs.
12
• Before playing, clean the discs
with a commercially available Playback order of MP3/WMA/AAC
cleaning cloth. Wipe each disc files
from the center out. Do not use
solvents such as benzine, MP3/WMA/AAC Folder
thinner, commercially available (album)
cleaners, or antistatic spray MP3/WMA/
intended for analog discs. AAC file
(track)
Notes on CD-R/CD-RW discs
• Some CD-Rs/CD-RWs (depending on the
equipment used for its recording or the condition
of the disc) may not play on this unit.
• You cannot play a CD-R/a CD-RW that is not
finalized.
• The unit is compatible with the ISO 9660 level 1/
level 2 format, Joliet/Romeo in the expansion
format, and Multi Session.
• The maximum number of:
– folders (albums): 150 (including root and empty
folders). About MP3 files
– files (tracks) and folders contained in a disc: 300 • MP3, which stands for MPEG-1 Audio Layer-3, is
(if a folder/file names contain many characters, a music file compression format standard. It
this number may become less than 300). compresses audio CD data to approximately 1/10
– displayable characters for a folder/file name is of its original size.
32 (Joliet), or 64 (Romeo). • ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to
• When the disc is recorded in Multi Session, only MP3 only. ID3 tag is 15/30 characters (1.0 and
the first track of the first session format is 1.1), or 63/126 characters (2.2, 2.3 and 2.4).
recognized and played (any other format is • When naming an MP3 file, be sure to add the file
skipped). The priority of the format is CD-DA, extension “.mp3” to the file name.
ATRAC CD and MP3/WMA/AAC. • During playback or fast-forward/reverse of a VBR
– When the first track is a CD-DA, only CD-DA of (variable bit rate) MP3 file, elapsed playing time
the first session is played. may not display accurately.
– When the first track is not a CD-DA, an ATRAC
CD or MP3/WMA/AAC session is played. If the
disc has no data in any of these formats, “NO About WMA files
MUSIC” is displayed. • WMA, which stands for Windows Media Audio,
is a music file compression format standard. It
Music discs encoded with copyright compresses audio CD data to approximately 1/22*
protection technologies of its original size.
This product is designed to play back discs that • WMA tag is 63 characters.
conform to the Compact Disc (CD) standard. • When naming a WMA file, be sure to add the file
Recently, various music discs encoded with extension “.wma” to the file name.
copyright protection technologies are marketed by • During playback or fast-forward/reverse of a VBR
some record companies. Please be aware that among (variable bit rate) WMA file, elapsed playing time
those discs, there are some that do not conform to may not display accurately.
the CD standard and may not be playable by this * only for 64 kbps
product.
Note on WMA
Playback of the following WMA files is not supported.
Note on DualDiscs – lossless compression
A DualDisc is a two sided disc product which – copyright-protected
mates DVD recorded material on one side with
digital audio material on the other side. However,
since the audio material side does not conform to About AAC files
the Compact Disc (CD) standard, playback on this • AAC, which stands for Advanced Audio Coding,
product is not guaranteed. is a music file compression format standard. It
compresses audio CD data to approximately 1/11*
of its original size.
• AAC tag is 126 characters.
• When naming an AAC file, be sure to add the file
extension “.m4a” to the file name.
Maintenance
Main unit Back of the front
Replacing the lithium battery of the panel
card remote commander
Under normal conditions, the battery will last Notes
approximately 1 year. (The service life may be • For safety, turn off the ignition before cleaning the
shorter, depending on the conditions of use.) connectors, and remove the key from the ignition
When the battery becomes weak, the range of the switch.
• Never touch the connectors directly with your fingers
card remote commander becomes shorter. Replace
or with any metal device.
the battery with a new CR2025 lithium battery. Use
of any other battery may present a risk of fire or
explosion.
+ side up
2 c
1
14
Removing the unit Specifications
1 Remove the protection collar.
AUDIO POWER SPECIFICATIONS
1 Detach the front panel (page 5). POWER OUTPUT AND TOTAL HARMONIC
2 Engage the release keys together with the DISTORTION
protection collar. 23.2 watts per channel minimum continuous
average power into 4 ohms, 4 channels driven
from 20 Hz to 20 kHz with no more than 5% total
harmonic distortion.
CEA2006 Standard
Power Output: 17 Watts RMS × 4 at
4 Ohms < 1% THD+N
SN Ratio: 82 dBA
Orient the release (reference: 1 Watt into 4 Ohms)
keys as shown.
3 Pull out the release keys to remove the
protection collar.
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
Tuner section
FM
Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
2 Remove the unit. Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
1 Insert both release keys simultaneously Selectivity: 75 dB at 400 kHz
until they click. Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz: 0.5 % (stereo),
0.3 % (mono)
Hook facing Separation: 35 dB at 1 kHz
inwards. Frequency response: 30 – 15,000 Hz
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: 30 µV
2 Pull the release keys to unseat the unit.
Power amplifier section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W × 4 (at 4 ohms)
General
Outputs:
3 Slide the unit out of the mounting. Audio outputs terminal (front, sub/rear switchable)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input terminal
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
18
En ce qui concerne l’installation et les
connexions, consulter le manuel
d’installation/raccordement fourni.
Avertissement
ATTENTION
L’utilisation d’instruments optiques avec ce
produit augmente les risques pour les yeux.
2
Table des matières
3
Félicitations ! Préparation
Nous vous remercions d’avoir fait l’acquisition Réinitialisation de l’appareil
de ce lecteur de disques compacts Sony. Ce
lecteur vous offre les fonctions suivantes. Avant la première mise en service de l’appareil,
• Lecture de CD après avoir remplacé la batterie du véhicule ou
Possibilité de lecture de CD-DA (contenant modifié les raccordements, vous devez
également des informations CD TEXT*), de réinitialiser l’appareil.
CD-R/CD-RW (fichiers MP3/WMA/AAC Retirez la façade, puis appuyez sur la touche
contenant également des multisessions RESET avec un objet pointu comme un stylo à
(page 14)) et de CD ATRAC (format ATRAC3 bille.
et ATRAC3plus (page 15)).
Type de Symbole indiqué sur le
disques disque Touche
RESET
CD-DA Remarque
Une pression sur la touche RESET remet l’heure à
zéro et efface certaines informations mémorisées.
MP3
WMA Préparation de la mini-
AAC télécommande
CD ATRAC
Avant d’utiliser la mini-télécommande pour la
première fois, retirez la feuille de protection.
• Réception radio
– Vous pouvez mémoriser jusqu’à 6 stations par
bande de fréquences (FM1, FM2, FM3, AM1
et AM2).
– BTM (mémorisation des meilleurs accords) :
l’appareil sélectionne des stations émettant un
signal fort et les mémorise.
• Réglages du son
– EQ3 stage2 : vous pouvez choisir l’une des
7 courbes d’égaliseur présélectionnées.
– DSO (répartiteur dynamique du son émis) : Réglage de l’horloge
création d’un son mieux réparti, à l’aide d’un
L’horloge numérique fonctionne suivant un cycle
haut-parleur virtuel, afin de renforcer le son
de 12 heures.
des haut-parleurs, même s’ils sont installés
dans la partie inférieure de la portière. 1 Appuyez sur la touche de sélection et
• Pilotage d’appareils en option maintenez-la enfoncée.
Cet appareil vous permet également de piloter L’écran de configuration apparaît.
des changeurs CD/MD en option.
• Raccordement d’un appareil auxiliaire 2 Appuyez plusieurs fois sur la touche
Une prise d’entrée AUX située à l’avant de de sélection jusqu’à ce que « CLOCK-
l’appareil permet de raccorder un appareil ADJ » apparaisse.
audio portatif. 3 Appuyez sur (SEEK) +.
* Un disque CD TEXT est un CD-DA contenant des
L’indication des heures clignote.
informations telles que le nom du disque, le nom de 4 Tournez la molette de réglage du
l’artiste et le nom des plages. volume pour régler l’heure et les
minutes.
Appuyez sur (SEEK) –/+ pour déplacer
l’indication numérique.
5 Appuyez sur la touche de sélection.
Le réglage est terminé et l’horloge démarre.
4
Pour afficher l’horloge, appuyez sur (DSPL).
Appuyez de nouveau sur (DSPL) pour revenir à Installation de la façade
l’écran précédent. Placez l’orifice A de la façade sur la tige B de
l’appareil, puis poussez doucement sur le côté
Avec la mini-télécommande
À l’étape 4, pour régler l’heure et les minutes, appuyez gauche pour l’engager en position.
sur M ou m. Appuyez sur (SOURCE) sur l’appareil (ou
insérez un disque) pour le faire fonctionner.
Retrait de la façade
A
Vous pouvez retirer la façade de cet appareil pour
le protéger du vol. B
Alarme d’avertissement
Si vous mettez la clé de contact en position OFF
sans ôter la façade, l’alarme d’avertissement
retentit pendant quelques secondes.
L’alarme est émise uniquement lorsque
c
l’amplificateur intégré est utilisé.
1 Appuyez sur (OFF).
L’appareil est mis hors tension.
Remarque
2 Appuyez sur (OPEN). Ne posez rien sur la face interne de la façade.
La façade bascule automatiquement vers le
bas.
3 Faites coulisser la façade vers la Insertion du disque dans le
droite, puis tirez doucement vers vous
l’extrémité gauche de la façade. lecteur
1 Appuyez sur (OPEN).
2 Insérez le disque (côté imprimé vers le
haut).
1
2
Remarques
• N’exercez pas de pression excessive sur la façade
et la fenêtre d’affichage et ne la l’echappez pas.
• N’exposez pas la façade à une température ou à un
taux d’humidité élevé. Évitez de la laisser dans un 3 Fermez la façade.
véhicule en stationnement ou sur le tableau de bord La lecture commence automatiquement.
ou la plage arrière.
Éjection du disque
1 Appuyez sur (OPEN).
2 Appuyez sur Z.
Le disque est éjecté.
3 Fermez la façade.
5
Emplacement des commandes et opérations de base
Appareil principal
12 3 4 5 67
DSO SOURCE
AUX
SEEK SEEK
EQ3 MODE
CAT GP/ALBM REP SHUF PAUSE
BTM DSPL 1 2 3 4 5 6 SCRL
CDX-GT510
CDX-GT51W
8 9 q; qa qs qd qf qg
Sans la façade
qh qj qk
RESET
8
Radio Réception des stations
mémorisées
Mémorisation et réception des 1 Sélectionnez la bande, puis appuyez
stations sur une touche numérique ((1) à (6)).
Attention
Pour syntoniser des stations pendant que vous
Syntonisation automatique des
conduisez, utilisez la fonction de mémorisation fréquences
des meilleurs accords (BTM) afin d’éviter tout
accident. 1 Sélectionnez la bande, puis appuyez
sur (SEEK) –/+ pour rechercher la
station.
Mémorisation automatique — BTM Le balayage s’interrompt lorsque l’appareil
capte une station. Répétez cette procédure
1 Appuyez plusieurs fois sur (SOURCE) jusqu’à ce que vous captiez la station
jusqu’à ce que l’indication « TUNER » souhaitée.
apparaisse. Conseil
Appuyez plusieurs fois sur (MODE) pour Si vous connaissez la fréquence de la station que
changer de bande. Vous pouvez sélectionner vous souhaitez écouter, maintenez la touche
FM1, FM2, FM3, AM1 ou AM2. (SEEK) –/+ enfoncée pour localiser la fréquence
approximativement, puis appuyez plusieurs fois sur
2 Appuyez sur la touche (BTM) et (SEEK) –/+ pour la régler avec précision
maintenez-la enfoncée jusqu’à ce que (syntonisation manuelle).
« BTM » clignote.
L’appareil enregistre les stations sur les
touches numériques dans l’ordre des
fréquences.
Un bip retentit lorsque le réglage est
mémorisé.
Mémorisation manuelle
1 Lorsque vous captez la station que
vous souhaitez mémoriser, appuyez
sur une touche numérique ((1) à (6))
et maintenez-la enfoncée jusqu’à ce
que l’indication « MEM » s’affiche.
Le numéro de la touche apparaît dans la
fenêtre d’affichage.
Remarque
Si vous essayez de mémoriser une autre station sur la
même touche numérique, la station mémorisée
précédemment est remplacée.
9
3 Tournez la molette de réglage du
Autres fonctions volume pour régler le paramètre
sélectionné.
Changement des réglages du Le niveau de volume peut être réglé par
incréments de 1 dB, de –10 dB à +10 dB.
son
10
Les paramètres suivants peuvent être réglés LOCAL (Mode de recherche locale)
(reportez-vous à la page indiquée pour plus de – « LOCAL-OFF » (z) : pour syntoniser une
détails) : réception normale.
« z » indique les réglages par défaut. – « LOCAL-ON » : pour syntoniser uniquement
les stations dont les signaux sont puissants.
CLOCK-ADJ (Réglage de l’horloge) (page 4) MONO (Mode monaural)*2
BEEP Pour améliorer une réception FM médiocre,
Pour régler « BEEP-ON » (z) ou « BEEP- sélectionnez le mode de réception mono.
OFF ». – « MONO-OFF » (z) : pour écouter les
AUX-A*1 (AUX audio) émissions stéréo en stéréo.
Pour régler l’affichage de la source AUX à – « MONO-ON » : pour écouter les émissions
« AUX-A-ON » (z) ou « AUX-A-OFF » stéréo en mono.
(page 11). LPF*3 (Filtre passe-bas)
A.OFF (Auto Off) Pour sélectionner la fréquence de coupure du
Pour éteindre automatiquement après un laps de caisson de graves : « LPF OFF » (z),
temps souhaité après la mise hors tension de « LPF125Hz » ou « LPF 78Hz ».
l’appareil : « A.OFF-NO » (z), « A.OFF-30S BTM (page 9)
(Secondes) », « A.OFF-30M (Minutes) » ou
« A.OFF-60M (Minutes) ». *1 Lorsque l’appareil est hors tension.
*2 Lors d’une réception FM.
SUB/REAR*1 *3 Lorsque la sortie audio est réglée à « SUB ».
Pour commuter la sortie audio.
– « SUB-OUT » (z) : pour émettre vers un
caisson de graves.
– « REAR-OUT » : pour émettre vers un Utilisation d’un équipement en
amplificateur de puissance. option
DEMO*1 (Démonstration)
Pour régler « DEMO-ON » (z) ou « DEMO-
OFF ». Appareils audio auxiliaires
DIM (Régulateur de luminosité) En raccordant un appareil audio portatif en
Pour modifier la luminosité de la fenêtre option à la prise d’entrée AUX (mini-prise
d’affichage. stéréo) de l’appareil, puis en sélectionnant
– « DIM-AT » (z) : réduit la luminosité simplement la source, vous pouvez écouter le son
automatiquement lorsque vous allumez les par l’intermédiaire des haut-parleurs de votre
phares. voiture. Vous pouvez régler le niveau du volume
– « DIM-ON » : pour réduire la luminosité de la quelle que soit la différence de son entre
fenêtre d’affichage. l’appareil et l’appareil audio portatif. Suivez la
– « DIM-OFF » : pour désactiver le régulateur procédure ci-dessous :
de luminosité.
Raccordement de l’appareil audio
ILM (Éclairage)
Pour modifier la couleur de l’éclairage :
portatif
« ILM-1 » (z) ou « ILM-2 ». 1 Mettez l’appareil audio portatif hors tension.
M.DSPL (Affichage animé) 2 Baissez le volume sur l’appareil.
Pour sélectionner le mode d’affichage animé. 3 Procédez au raccordement à l’appareil.
– « M.DSPL-SA » (z) : pour afficher les motifs
animés et l’analyseur de spectre.
– « M.DSPL-ON » : pour afficher les motifs
suite à la page suivante t
animés.
– « M.DSPL-OFF » : pour désactiver l’affichage
animé.
A.SCRL (Défilement automatique)
Pour faire défiler automatiquement une option
dont l’affichage est long lorsque vous changez
de disque, d’album, de groupe ou de plage.
– « A.SCRL-ON » (z) : pour faire défiler les
rubriques.
– « A.SCRL-OFF » : pour ne pas faire défiler les
rubriques.
11
Saut d’albums et de disques
1 En cours de lecture, appuyez sur (1)/(2)
AUX (GP/ALBM –/+).
Appuyez sur (1)/(2)
Pour sauter
(GP/ALBM –/+)
un album et relâchez la touche
AUX (maintenez-la enfoncée
quelques instants).
plusieurs et appuyez de nouveau sur la
albums de suite touche dans les 2 secondes qui
suivent.
Cordon de des disques de façon répétée.
raccordement*
(non fourni) plusieurs puis appuyez de nouveau sur la
disques de suite touche dans les 2 secondes qui
suivent et maintenez-la
* Veillez à utiliser une fiche droite.
enfoncée.
Numéro de disque
SEL DSPL
MODE MODE
La lecture commence. DSPL SEL
12
Emplacement des commandes
Les touches correspondantes du satellite de Informations complémentaires
commande pilotent les mêmes fonctions que
celles de l’appareil. Précautions
ATT • Si votre véhicule est resté stationné en plein soleil,
SEL
laissez refroidir l’appareil avant de l’utiliser.
PRESET/ • L’antenne électrique se déploie automatiquement
DISC lorsque l’appareil fonctionne.
MODE
Condensation
SOURCE Par temps de pluie ou dans des régions très humides,
OFF
DSPL de la condensation peut se former à l’intérieur des
lentilles et dans la fenêtre d’affichage de l’appareil.
VOL SEEK/AMS OFF Si cela se produit, l’appareil ne fonctionne pas
Les commandes suivantes du satellite de correctement. Dans ce cas, retirez le disque et
commande ont une fonction différente de celles attendez environ une heure que l’humidité se soit
de l’appareil. évaporée.
14
• Les caractères du nom de dossier/fichier et les
À propos des fichiers WMA informations textuelles de SonicStage sont
• WMA, qui signifie Windows Media Audio, est affichés.
une norme de format de compression des fichiers Pour plus de détails sur CD ATRAC, reportez-vous
audio. Elle permet la compression des données de au manuel SonicStage ou SonicStage Simple
CD audio à environ 1/22e* de leur taille d’origine. Burner.
• L’étiquette WMA comporte 63 caractères.
• Lors de l’identification d’un fichier WMA, veillez Remarque
à ajouter l’extension « .wma » au nom du fichier. Veillez à créer le CD ATRAC à l’aide d’un logiciel
• Pendant la lecture ou pendant l’avance/le retour autorisé SonicStage version 2.0 ou ultérieure, ou
rapide d’un fichier WMA VBR (débit binaire SonicStage Simple Burner 1.0 ou 1.1.
variable), le temps de lecture écoulé affiché peut
ne pas être correct. Si vous avez des questions ou des problèmes
concernant cet appareil qui ne sont pas abordés dans
* uniquement pour 64 kbit/s ce mode d’emploi, communiquez avec votre
Remarque sur le format WMA détaillant Sony.
La lecture des fichiers WMA suivants n’est pas prise
en charge.
– compression sans perte Entretien
– protection des droits d’auteur
Remplacement de la pile au lithium
À propos des fichiers AAC de la télécommande
• AAC, qui signifie Advanced Audio Coding, est Dans des conditions d’utilisation normales, la pile
une norme de format de compression des fichiers dure environ 1 an. (En fonction des conditions
audio. Elle permet la compression des données de d’utilisation, sa durée de vie peut être plus courte.)
CD audio à environ 1/11e* de leur taille d’origine. Lorsque la pile est faible, la portée de la mini-
• L’étiquette AAC comporte 126 caractères. télécommande diminue. Remplacez la pile par une
• Lors de l’identification d’un fichier AAC, veillez à nouvelle pile au lithium CR2025. L’utilisation de
ajouter l’extension « .m4a » au nom du fichier. tout autre type de pile entraîne un risque d’incendie
• Pendant la lecture ou pendant l’avance/le retour ou d’explosion.
rapide d’un fichier AAC VBR (débit binaire
variable), le temps de lecture écoulé affiché peut pôle + vers le haut
ne pas être correct.
* uniquement pour 128 kbit/s 2 c
Remarque sur le format AAC
La lecture des fichiers protégés par des droits d’auteur 1
n’est pas prise en charge.
Remarques sur la pile au lithium
• Tenez la pile au lithium hors de portée des enfants.
À propos des CD ATRAC En cas d’ingestion de la pile, consultez
immédiatement un médecin.
Format ATRAC3plus • Essuyez la pile avec un chiffon sec pour assurer un
ATRAC3, qui signifie Adaptive Transform Acoustic bon contact.
Coding3, est une technologie de compression audio. • Veillez à respecter la polarité lors de l’installation de
Elle permet la compression des données de CD la pile.
• Ne tenez pas la pile avec des pinces métalliques,
audio à environ 1/10e de leur taille d’origine.
car cela peut entraîner un court-circuit.
ATRAC3plus est un format étendu de ATRAC3 et
permet la compression des données des CD audio à
environ 1/20e de leur taille d’origine. Cet appareil ATTENTION
accepte à la fois les formats ATRAC3 et Utilisée de façon incorrecte, la pile peut
ATRAC3plus. exploser. Ne pas la recharger, la démonter ni
la jeter au feu.
CD ATRAC
Le format CD ATRAC enregistre des données de
CD audio compressés au format ATRAC3 ou
ATRAC3plus à l’aide de logiciels autorisés comme
suite à la page suivante t
SonicStage version 2.0 ou ultérieure ou SonicStage
Simple Burner.
• Nombre maximal de :
– dossiers (groupes) : 255
– fichiers (plages) : 999
15
Remplacement du
fusible Démontage de l’appareil
Lorsque vous remplacez le
fusible, veillez à utiliser un 1 Retirez le tour de protection.
fusible dont la capacité, en 1 Retirez la façade (page 5).
ampères, correspond à la valeur
indiquée sur l’ancien fusible. Si 2 Insérez les clés de déblocage
le fusible fond, vérifiez le simultanément dans le tour de protection.
branchement de l’alimentation
et remplacez le fusible. Si le Fusible (10 A)
nouveau fusible fond
également, il est possible que
l’appareil soit défectueux. Dans ce cas, contactez
votre détaillant Sony le plus proche.
2 Retirez l’appareil.
Appareil principal Arrière de la façade 1 Insérez simultanément les deux clés de
déblocage jusqu’au déclic.
Remarques
• Pour plus de sécurité, coupez le moteur avant de Crochet tourné
nettoyer les connecteurs et retirez la clé du contact. vers l’intérieur.
• Ne touchez jamais les connecteurs directement
avec les doigts ou avec un objet métallique.
16
Accessoires/appareils en option :
Caractéristiques techniques Satellite de commande : RM-X4S
Câble BUS (fourni avec un câble à broche RCA) :
Lecteur CD RC-61 (1 m), RC-62 (2 m)
Changeur CD (10 disques) : CDX-757MX
Rapport signal/bruit : 120 dB Changeur CD (6 disques) : CDX-T69
Réponse en fréquence : 10 à 20 000 Hz Sélecteur de source : XA-C40
Pleurage et scintillement : en dessous du seuil Sélecteur AUX-IN : XA-300
mesurable Adaptateur d’interface pour iPod : XA-110IP
Radio Il est possible que votre détaillant ne dispose pas de
FM certains accessoires énoncés ci-dessus. Veuillez
Plage de syntonisation : 87,5 à 107,9 MHz vous adresser à lui pour tout renseignement
Borne d’antenne : connecteur d’antenne externe complémentaire.
Fréquence intermédiaire : 10,7 MHz/450 kHz
Sensibilité utile : 9 dBf Brevets américains et internationaux sous licence
Sélectivité : 75 dB à 400 kHz de Dolby Laboratories.
Rapport signal/bruit : 67 dB (stéréo), 69 dB (mono)
Distorsion harmonique à 1 kHz : 0,5 % (stéréo),
0,3 % (mono) Licence de la technologie de codage audio MPEG
Séparation : 35 dB à 1 kHz Layer-3 et des brevets obtenue de Fraunhofer IIS et
Réponse en fréquence : 30 à 15 000 Hz Thomson.
AM
Plage de syntonisation : 530 à 1 710 kHz Remarque
Borne d’antenne : connecteur d’antenne externe Cet appareil ne doit pas être branché à un
Fréquence intermédiaire : 10,7 MHz/450 kHz préamplificateur numérique ni à un égaliseur
Sensibilité : 30 µV compatible avec le système Sony BUS.
La conception et les caractéristiques techniques sont
Amplificateur de puissance sujettes à modification sans préavis.
Sorties : sorties de haut-parleurs (connecteurs de
sécurité)
Impédance du haut-parleur : 4 à 8 ohms
Puissance restituée maximale : 52 W × 4 (à 4 ohms)
19
If you have any questions/problems
regarding this product, try the following:
http://www.sony.net/
Sony Corporation Printed in Thailand