Professional Documents
Culture Documents
Aluminium profiles:
- Pocket N° 1
- Pocket N° 2
- Pocket N° 3
- Pocket N° 4
- Pocket N °5
- Pocket N° 6
- Pocket N°7
- Pocket No. 8
Accessories:
Before beginning installation of your To Be Faster, here is the link to two videos on mounting profiles with single
90 ° and said angle bracket "cross":
https://www.youtube.com/watch?v=H4BQPkBkzco
https://www.youtube.com/watch?v=3FKmVKBaAtY
You will need a key 6 point No. 6 to mount your cockpit.
Do not over tighten the screws during installation, in order to make adjustments to your liking.
Profiles Information
The anodized aluminum light type, 40mm or 80mm section, has one or two 10mm slots to insert nuts.
- Pocket N° 1
IMPORTANT NOTE:
When mounting, do not tighten the screws. Just come to abut against the brackets. You will eventually need to
move the profiles to find your personal setting, your own driving position.
- Fix 3 profiles 80x40 mm X 700 perpendicular to 1195mm X 2 profiles 80x40 with 90 ° angle brackets and fasteners
provided in the pocket 1. (picture)
- Fix the profile 40x40 X 700 to the front of your To Be raignure faster on the bottom (if you own a pedal HE or F1
style) or on the top groove (pedals Thrustmaster, Logitech or Fanatec) profiles 80x40 X 1195mm.
- For a lower position:
Leave a space of 400mm between the two profiles 80x40 X 700mm which are at the back of your To Be Faster to
fill come fix them later between the 2 profiles 80x40 X400 that will receive your tub. (Photo)
- To have a high position:
Leave a space of 320mm between the two profiles 80x40 X 700mm which are at the back of your To Be Faster to
fill come fix them later over the 2 profiles 80x40 X 400 who will receive your seat. (Photo)
- You can now set as indicated above profiles 80x40 X 700mm or between the two profiles 80x40 X 700mm (photo )
with the help of 4 brackets "cross" (small pocket 4 brackets and fasteners in pocket 1).
Important Note: Attention within the meaning of the slides so that the handle will allow you to go backward or
forward either forward of the cockpit!
- Adjust your bucket on the mounting brackets loosely them. You may be taken subsequently to change the tilt of
your tub for comfort.
- Then move your bucket compared to the width of your To Be Faster and tighten strong. (About 14 cm on each
side - see photo)
For step 2, bring you to:
- Pocket N° 2
- Pocket N° 3
IMPORTANT NOTE:
When mounting, do not tighten the screws. Just come to abut against the brackets. You will eventually need to
move the profiles to find your personal setting, your own driving position.
- Fix the 3 profiles 80x40 X 700mm with the big gray machined brackets and fasteners of the pocket No. 2.
(photo).
- Fix the 4 brackets strengthened (pocket No. 3) on each sides of the profiles 80x40 X 700mm (photo)
- Install the wheel bracket block on your base and secure it about 30 cm from the front of your cockpit. The
distance can varied according to your height and riding position.
In step 3 (pedal support) Provide with:
- Poche N° 6
IMPORTANT NOTE:
When mounting, do not tighten the screws. Just come to abut against the brackets. You will eventually
need to move the profiles to find your personal setting, your own driving position.
- Attach the two sections 40x40 X 340mm between two profiles 40x40 X 400mm (brackets outward
frame - photo)
Fix your pedal on the flat brackets, using the screws supplied and following the model of your pedals (spacers +
screws 6x20mm + washers 6) or (washers 8 + screws 8x25mm + brake nuts 8)
Now you can adjust the depth and angle of your pedals and make final tightening.
Step 4: Mounting the carrier Mouse
Secure and cross sections 40x40x200mm L with square cross, 2 post-mounting nuts 8 and 2 screws 8x20mm.
Attach the second cross bracket down on the side of the profile used to walk with 1 post-mounting nut 8 et 1
screws 8x20mm.
Attach the Mouse support tray on the top section using 2 post-mounting nuts 8, 2 washers 8 et 2 screws
8x15mm.
Mount the end caps.
- 1 screw 8x20mm
- 1 post-mounting nut 8
Attach the Mouse support on the cockpit structure « To Be Faster » using 1 post-mounting nut 8 and 1 screw
8x20mm.
You can now adjust your position and make the final tightening.