Professional Documents
Culture Documents
FOR
1 Contents
2 Drawing Reference
3 GLASS REPORT
4 SS Railing Staad
GENERAL NOTES:-
- Information within the drawing is copyright of Envelopetechnik at all time and shall not
to be used for purposes other than design co-ordination of this particular project.
- All dimensions are in millimetres unless noted otherwise. All dimensions shall be verified
on site and approved. Do not scale from drawings.
- This drawing is read in conjunction with other relevant architectural, structural , MEP
drawings as well as technical specifications, BOQ and conditions of contract.
- Performance shall meet the requirements of the technical specifications at all the time.
- This drawing is for design intent only, not for Construction. Although it suggests some
materials, minimum thickness, techniques and methods, the Contractor must provide the
solution for the work. Should the Contractor adopt the details or arrangements indicated on
this drawings, it shall be deemed that he has checked the materials, their thickness, their
buildability and performance in terms of all relevant regulations and codes of practice, and
manufacturers' recommendations for any products referred to.
- Where this drawing identifies preferred systems and materials, the Contractor is to
confirm them as being for their specified and intended purpose with the Bidding return. If no
such specific confirmation is received, then the submission of the Bidding return itself shall
constitute such a confirmation. In absence of any such proposals, comments or observations,
the contractor shall be deemed to have accepted and approved such requirements,
stipulations or preferences which shall then form part of this building and contract.
INSIDE
OUTSIDE LAMINATED GLASS AS
PER SPEC.
1050 mm
S.S LUMINIUM MEMBER AS
PER SPEC.
1200 mm
NON-STANING WEATHER SEALANT
WITH CLOSE CELL BACKER ROD
300 mm
18 mm
SLOPE
SS BASE PLATE
50 mm
00 08-11-22 FZ TENDER
Rev Date By Description
DSGN AT
50 mm
DRWN AT
50 mm CHKD MK
APPD MS
NAME SIGN DATE
Client:
15 mm INORBIT MALL
25 mm 40 mm 120 mm 50 mm 150 mm Mindspace, Madhapur-Telangana.
Architect:
Project Name:
INORBIT MALL
225 mm 300 mm HYDERABAD
250 mm
Drawing Title:
GLASS RAILING WITH MOTIF PANEL
JAMB SECTION DETAIL
01 GLASS RAILING WITH MOTIF PANEL JAMB SECTION DETAIL
Drawing No: 2021230-TD-DT-619
DT- 619 SCALE - 1:2 INORBIT MALL INDICATIVE 3D VIEW Released for: Scale: Size: Rev.No.
TENDER AS SHOWN A1
Job No Sheet No Rev
1
Part
Software licensed to
Job Title Ref
By Date07-Feb-19 Chd
Job Information
Engineer Checked Approved
Name:
Date: 07-Feb-19
Project ID
Project Name
Primary 1 DL
Primary 2 WL
Primary 4 LL
Combination 3 DL+WL
Combination 5 DL+LL
Plate Thickness
Prop Node A Node B Node C Node D Material
(cm) (cm) (cm) (cm)
1 1.200 1.200 1.200 1.200 GLASS
Materials
Mat Name E ν Density α
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 GLASS 70.000 0.220 2.55E+3 0.000
3 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
4 ALUMINUM 68.948 0.330 2.71E+3 23E -6
5 CONCRETE 21.718 0.170 2.4E+3 10E -6
1 DL Dead
2 WL Wind
Print Time/Date: 14/02/2023 00:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 1 of 5
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref
By Date07-Feb-19 Chd
3 DL+WL 1 DL 1.00
2 WL 1.00
5 DL+LL 1 DL 1.00
4 LL 1.00
1.330m
0.500m
1.000m
Y
X
Z Load 1
Whole Structure
-0.001 N/mm2
-0.001 N/mm2
-0.001 N/mm2
1.330m -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 0.500m
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
1.000m -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2 -0.001 N/mm2
Y -0.001 N/mm2 -0.001 N/mm2
X
Z -0.001 N/mm2
-0.001 N/mm2 Load 2
-0.001 N/mm2
Print Time/Date: 14/02/2023 00:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 2 of 5
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref
By Date07-Feb-19 Chd
0.800 kN
1.330m
0.500m
1.000m
Y
X
Z Load 4
Max Absolute
N/mm2
<= 0.754
2.63
4.51
6.38
8.26
10.1
12
13.9
15.8
17.6
19.5
21.4
23.3
25.1
27
28.9
>= 30.8
Y
X
Z Load 5
Print Time/Date: 14/02/2023 00:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 3 of 5
Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref
By Date07-Feb-19 Chd
0.800 kN
X = 0.013 kN
Y = 0.122 kN
Z = -1.257 kN
MX = FREE
MY = FREE
MZ = FREE
X = -0.013 kN
Y = 0.122 kN
Z = -0.183 kN
MX = FREE
X = -0.047 kN
MY = FREE
Y = 0.077 kN
MZ = FREE
Z = 0.457 kN
MX = FREE
MY = FREE
MZ = FREE
Y
X
Z X = 0.047 kN
Y = 0.077 kN Load 5
Z = 0.183 kN
MX = FREE
MY = FREE
MZ = FREE
Print Time/Date: 14/02/2023 00:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 4 of 5
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref
By Date07-Feb-19 Chd
-0.001 N/mm2
-0.001 N/mm2
-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2 X = 0.013 kN
-0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2 Y = 0.122 kN
-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 Z = 0.638 kN
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 MX = FREE
-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 MY = FREE
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 -0.001
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 N/mm2 -0.001 N/mm2 MZ = FREE
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2 -0.001
N/mm2-0.001 N/mm2-0.001 N/mm2 N/mm2
-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2-0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2
X = -0.013 kN -0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 -0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2-0.001 N/mm2
Y = 0.122 kN -0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2
Z = 0.638 kN -0.001 N/mm2-0.001 N/mm2 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2-0.001 N/mm2
MX = FREE -0.001 N/mm2-0.001 N/mm2-0.001 N/mm2 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 -0.001 N/mm2 X = -0.047 kN
MY = FREE -0.001 N/mm2-0.001 N/mm2 N/mm2-0.001 N/mm2
-0.001 N/mm2-0.001 N/mm2-0.001 -0.001 N/mm2 Y = 0.077 kN
Y MZ = FREE N/mm2
X -0.001 N/mm2-0.001 N/mm2 Z = 0.160 kN
-0.001 N/mm2-0.001 N/mm2
Z -0.001 N/mm2-0.001 N/mm2 MXLoad
= FREE
3
-0.001 N/mm2 MY = FREE
-0.001 N/mm2
-0.001 N/mm2 MZ = FREE
X = 0.047 kN
Y = 0.077 kN
Z = 0.160 kN
MX = FREE
MY = FREE
MZ = FREE
Print Time/Date: 14/02/2023 00:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 5 of 5
Job No Sheet No Rev
1
Part
Software licensed to
Job Title Ref
By Date14-Feb-23 Chd
Job Information
Engineer Checked Approved
Name:
Date: 14-Feb-23
Project ID
Project Name
Primary 1 DL
Primary 3 LL -LINE
Primary 4 WL
Combination 6 DL+LL LINE
Combination 7 DL+WL
Combination 9 1.5DL+1.5LL LINE
Combination 10 1.5DL+1.5WL
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 TUB100504 10.900 44.900 134.000 109.865 STAINLESSSTEEL
2 PIP483M 4.530 11.600 11.600 23.171 STAINLESSSTEEL
Materials
Mat Name E ν Density α
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6
1 DL Dead
Print Time/Date:
3 14/02/2023 01:01
LL -LINE STAAD.Pro V8i (SELECTseries
Live 6) 20.07.11.90 Print Run 1 of 5
4 WL Wind
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref
By Date14-Feb-23 Chd
1.330m
1.330m
1.050m
Y
X
Z Load 9
Whole Structure
Print Time/Date: 14/02/2023 01:01 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 2 of 5
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref
By Date14-Feb-23 Chd
1.330m
48 DIA ,3mm thk pipe
1.330m
1.050m
Y
X
100X50X4 SS TUBE
Z
Load 9
Whole Structure
1.330m
2.250 kN/m
1.330m
1.050m
2.250 kN/m
Y
X
Z
Load 3
Print Time/Date: 14/02/2023 01:01 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 3 of 5
Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref
By Date14-Feb-23 Chd
-0.240 kN
1.330m
-1.200 kN
-0.150 kN
-0.320 kN
-0.240 kN
1.330m
1.050m -1.200 kN
-0.150 kN
-0.320 kN
-0.240 kN
-1.200 kN
-0.150 kN
Y
X -0.320 kN
Z
Load 4
7.7e-005
0.384
0.488
0.191
0.701
0.408
7.7e-005
0.222
0.242
0.351 0.514
0.701
0.779
7.7e-005
0.384
0.488
0.191 0.989
0.408
Y
X
Z 0.514 Load 4
Print Time/Date: 14/02/2023 01:01 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 4 of 5
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref
By Date14-Feb-23 Chd
Max: 1.884 mm
Max: 1.650 mm
Max: 1.502 mm
Max: 3.818 mm
Max: 3.373 mm
Max:
Max:3.067 mm
3.054 mm
Max: 0.104 mm
Max: 3.922 mm
Max: 1.581 mm
Max: 1.884 mm
Max: 1.650 mm
Max: 1.502 mm
Max: 0.214 mm
Max: 0.771 mm
Y Max: 0.104 mm
X Load 6 : Displacement
Z
Displacement - mm
3.375 kN/m
3.375 kN/m
X = -0.162 kN
Y = 0.090 kN
Z = -2.138 kN
MX = -2.074 kN-m
MY = -0.320 kN-m
MZ = 0.132 kN-m
X = -0.000 kN
Y = 0.109 kN
Z = -4.702 kN
MX = -4.366 kN-m
MY = -0.000 kN-m
Y
X MZ = 0.000 kN-m
Z
Load 9
X = 0.162 kN
Y = 0.090 kN
Z = -2.138 kN
MX = -2.074 kN-m
MY = 0.320 kN-m
Whole Structure Loads 4.0024kN:1m 9 1.5DL+1.5LL LINE
Print Time/Date: 14/02/2023 01:01 STAAD.Pro V8i (SELECTseries 6) 20.07.11.90 Print Run 5 of 5
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200-R V3 + HIT-V-R M12
Return period (service life in years): 50
Item number: not available (element) / 2262134 HIT-HY 200-R V3
(adhesive)
Effective embedment depth: hef,act = 120.0 mm (hef,limit = - mm)
Material: A4
Evaluation Service Report: ETA 19/0601
Issued I Valid: 02/12/2021 | -
Proof: Design Method ETAG BOND (EOTA TR 029)
Stand-off installation: eb = 0.0 mm (no stand-off); t = 16.0 mm
Anchor plate :
R lx x ly x t = 330.0 mm x 180.0 mm x 16.0 mm; (Recommended plate thickness: 16.0 mm)
Application also possible with HVU2 + HAS(-E)R M12_hef1 under the selected boundary conditions.
More information in section Alternative fastening data of this report.
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
N
NSd £ NRd,s = Rk,s EOTA TR 029, Table 5.2.2.1
gM,s
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
N
NSd £ NRd,p = Rk,p EOTA TR 029, Table 5.2.2.1
gM,p
0 Ap,N
NRk,p = NRk,p · 0
· y s,Np · y g,Np · y ec1,Np · y ec2,Np · y re,Np EOTA TR 029, Eq. (5.2)
Ap,N
0
NRk,p = p · d · hef · t Rk EOTA TR 029, Eq. (5.2a)
0
Ap,N = scr, Np · scr,Np EOTA TR 029, Eq. (5.2b)
0.5
t Rk,ucr
scr,Np = 20 · d · (
7.5 )
£ 3 · hef EOTA TR 029, Eq. (5.2c)
s
ccr,Np = cr,Np EOTA TR 029, Eq. (5.2d)
2
c
y s,Np = 0.7 + 0.3 · 1.00 EOTA TR 029, Eq. (5.2e)
ccr,Np £
0,5
y g,Np
0
= y g,Np - (s s )
cr,Np
· (y g,Np - 1) ³ 1.00
0
EOTA TR 029, Eq. (5.2f)
1,5
0
y g,Np = √n - (√n - 1) · (k · √dh · t· f ef
Rk
ck,cube
) ³ 1.00 EOTA TR 029, Eq. (5.2g)
1
y ec1,Np = 1.00 EOTA TR 029, Eq. (5.2h)
2 · ec1,N £
1+
scr,Np
1
y ec2,Np = 1.00 EOTA TR 029, Eq. (5.2h)
2 · ec2,N £
1+
scr,Np
h
y re,Np = 0.5 + ef £ 1.00 EOTA TR 029, Eq. (5.2i)
200
2 0 2 2
Ap,N [mm ] Ap,N [mm ] t Rk,ucr,25 [N/mm ] scr,Np [mm] ccr,Np [mm] cmin [mm]
174,000 129,600 18.00 360.0 180.0 150.0
0
yc t Rk,ucr [N/mm ]
2
k y g,Np y g,Np
1.018 18.33 3.200 1.000 1.000
Group anchor ID
1, 2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
N
NSd £ NRd,c = Rk,c EOTA TR 029, Table 5.2.2.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N EOTA TR 029, Eq. (5.3)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef EOTA TR 029, Eq. (5.3a)
0
Ac,N = scr,N · scr,N EOTA TR 029, Eq. (5.3b)
c
y s,N = 0.7 + 0.3 · 1.00 EOTA TR 029, Eq. (5.3c)
ccr,N £
hef
y re,N = 0.5 + 1.00 EOTA TR 029, Eq. (5.3d)
200 £
1
y ec1,N = 1.00 EOTA TR 029, Eq. (5.3e)
2 · ec1,N £
1+
scr,N
1
y ec2,N = 1.00 EOTA TR 029, Eq. (5.3e)
2 · ec2,N £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm]
174,000 129,600 180.0 360.0
Group anchor ID
1, 2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
V
VSd £ VRd,s = Rk,s EOTA TR 029, Table 5.2.3.1
gM,s
V
VSd £ VRd,cp = Rk,cp EOTA TR 029, Table 5.2.3.1
gM,c,p
VRk,cp = k · min (NRk,p; NRk,c) EOTA TR 029, Eq. (5.7), (5.7a)
0 A
NRk,c = NRk,c · 0c,N · y s,N · y re,N · y ec1,N · y ec2,N EOTA TR 029, Eq. (5.3)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef EOTA TR 029, Eq. (5.3a)
0
Ac,N = scr,N · scr,N EOTA TR 029, Eq. (5.3b)
c
y s,N = 0.7 + 0.3 · £ 1.00 EOTA TR 029, Eq. (5.3c)
ccr,N
hef
y re,N = 0.5 + 1.00 EOTA TR 029, Eq. (5.3d)
200 £
1
y ec1,N = 1.00 EOTA TR 029, Eq. (5.3e)
2 · ec1,V £
1+
scr,N
1
y ec2,N = 1.00 EOTA TR 029, Eq. (5.3e)
2 · ec2,V £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k-factor k1
174,000 129,600 180.0 360.0 2.000 10.100
Group anchor ID
1, 2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
V
VSd £ VRd,c = Rk,c EOTA TR 029, Table 5.2.3.1
gM,c
0 Ac,V
VRk,c = VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V EOTA TR 029, Eq. (5.8)
Ac,V
0 a b 1,5
VRk,c = k1 · dnom · hef · √fck,cube · c1 EOTA TR 029, Eq. (5.8a)
0,5
a = 0.1 · ( ) hef
c1
EOTA TR 029, Eq. (5.8b)
0,2
= 0.1 · (
c )
d nom
b EOTA TR 029, Eq. (5.8c)
1
0 2
Ac,V = 4.5 · c1 EOTA TR 029, Eq. (5.8d)
c2
y s,V = 0.7 + 0.3 · 1.00 EOTA TR 029, Eq. (5.8e)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 EOTA TR 029, Eq. (5.8f)
√
1
2
y a,V =
(cos aV) +
2
(sin2.5a )
V ³ 1.00 EOTA TR 029, Eq. (5.8g)
1
y ec,V = 1.00 EOTA TR 029, Eq. (5.8h)
2 · ec,V £
1+
3 · c1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow 4 times with the hand pump, brush 4 times, blow again 4 times
with the hand pump).
• Characteristic bond resistances depend on short- and long-term temperatures.
• Please contact Hilti to check feasibility of HIT-V rod supply.
• Edge reinforcement is not required to avoid splitting failure
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
(1)
Mallée, R.; Riemann, H. (1990): Ankerplattenbefestigungen mit Hinterschnittdübeln,
Bauingenieur 65 (1990), S. 49 - 57, Springer VDI-Verlag, 1990
Mallée, R.; Burkhardt, F. (1999): Befestigungen von Ankerplatten mit Dübeln, Beton und
Stahlbetonbau 94, Heft 12, S. 502 - 511, Ernst & Sohn Verlag, 1999
8.2 Results
Stress distribution s 11
2
227.27 [N/mm ]
2
-108.50 [N/mm ]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Stress distribution s 22
2
122.69 [N/mm ]
2
-208.60 [N/mm ]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Deformations (z-direction)
0.5 [mm]
-0.2 [mm]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 12
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
9 Installation data
Anchor plate, steel: E 250 (Fe 410 W) A; E = 200,000.00 N/mm ; fyk = 250.00
2 Anchor type and diameter: HIT-HY 200-R V3 + HIT-V-R
N/mm
2 M12
Profile: Rectangular Hollow Sections India, 100x50x4; (L x W x T) = 100.0 mm Item number: not available (element) / 2262134 HIT-HY
x 50.0 mm x 4.0 mm 200-R V3 (adhesive)
Hole diameter in the fixture: df = 14.0 mm Maximum installation torque: 40 Nm
Plate thickness (input): 16.0 mm Hole diameter in the base material: 14.0 mm
Recommended plate thickness: 16.0 mm Hole depth in the base material: 120.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 150.0 mm
Cleaning: Manual cleaning of the drilled hole according to instructions for use is
required.
Hilti HAS-U threaded rod with HIT-HY 200-R V3 injection mortar with 120 mm embedment h_ef, M12, Stainless steel, Hammer drilled
installation per ETA 19/0601
y
165.0 165.0
90.0
90.0
2 1
x
90.0
90.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
12
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 13
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
10 Alternative fastening
10.1 Alternative fastening data
Anchor plate :
R lx x ly x t = 330.0 mm x 180.0 mm x 16.0 mm; (Recommended plate thickness: not calculated)
Hilti HAS-U threaded rod with HVU2 capsule mortar with 110 mm embedment h_ef, M12_hef1, Stainless steel, Hammer drilled installation per
ETA-16/0515
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
13
Hilti PROFIS Engineering 3.0.83
www.hilti.in
Company: Page: 14
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Feb 14, 2023 Date: 13/02/2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
14