Professional Documents
Culture Documents
Test Questionnaire: GENERAL INSTRUCTIONS: Keep Your Cellphones in Your Bags and Turn It Off or Set It in Silent Mode
Test Questionnaire: GENERAL INSTRUCTIONS: Keep Your Cellphones in Your Bags and Turn It Off or Set It in Silent Mode
19084895
TEST QUESTIONNAIRE
CBE 9 (Mechanics of Deformable Bodies)
Midterm Examination
Name: _____________________________ Date: ___________________
Year/Section: _______________________ Permit Number: __________
Instructor: __________________________ Score: __________________
GENERAL INSTRUCTIONS: Keep your cellphones in your bags and turn it off or set it in silent mode.
Answer silently and mind your own paper. You can only ask questions to the proctor. Talking with your
seatmates is strictly prohibited.
Multiple Choice: Read and analyze each of the following questions carefully. Encircle the letter of
your answer.
OBJECTIVE TYPE QUESTIONS: Strength of Materials
1. A stress that is caused by forces acting along or parallel to the area of resisting forces.
a. Normal c. tensile
b.Shearing d. compressive
3. The straight line portion from the origin up to the elastic limit of the stress-strain diagram is
termed as the
a. Constant limit c.Proportional limit
b. Linear limit d. none of these
4. The stress beyond which the material will not return to its original shape when unloaded.
a.elastic limit c. yield point
b. Plastic limit d. rupture strength
5. It is the point on the stress-strain diagram in which there is an appreciable elongation of the
material without any corresponding increase of load.
a. Ultimate point c.yield point
b. Elastic point d. rupture strength
7. It is defined as the actual strews the material has when under load.
a.Working stress c. yield stress
b. Normal stress d. minimum stress
AGUSAN DEL SUR STATE COLLEGE OF AGRICULTURE AND TECHNOLOGY
Bunawan, Agusan del Sur
Doc No.: F-DOI-018
website: http://asscat.edu.ph Effective Date: 08/25/2017
email address: op@asscat.edu.ph; mobile no.: +639486379266 Rev No.: 0
Page No.: 2 of 7
19084895
TEST QUESTIONNAIRE
8. In many materials the proportion limit is about _________ of the ultimate strength.
a .Equal c. one third
b.One half d. one fourth
9. The slope of the straight line portion of the stress-strain diagram is the ratio of stress to
strain is called.
a .Poisson’s ratio c. modulus of rigidity
b.Modulus of elasticity d. Hook’s law
10. It permits us to extend Hook’s law of uniaxial stress to the case of biaxial stress.
a. Stress-strain ratio c.Poisson’s ratio
b.Free body diagram d. moment-shear diagram
11. Common values of Poisson’s ratio 0.25 to 0.30 for steel, and approximately _________ for
concrete.
a. 0.20 c.0.33
b. 0.38 d. 0.23
19084895
TEST QUESTIONNAIRE
b) Q
c) T
d) N
19084895
TEST QUESTIONNAIRE
20. Which of the following can be the value of Poisson’s ratio for an engineering structure?
a) 2
b) 0.4
c) 29
d) 100
Problem Solving: Show your solutions (10 points each).
21.
Problem
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6-
m length when subjected to a torque of 12 kN·m? What maximum shearing stress is developed?
Use G = 83 GPa.
22.
23.
AGUSAN DEL SUR STATE COLLEGE OF AGRICULTURE AND TECHNOLOGY
Bunawan, Agusan del Sur
Doc No.: F-DOI-018
website: http://asscat.edu.ph Effective Date: 08/25/2017
email address: op@asscat.edu.ph; mobile no.: +639486379266 Rev No.: 0
Page No.: 5 of 7
19084895
TEST QUESTIONNAIRE
23.
24.
AGUSAN DEL SUR STATE COLLEGE OF AGRICULTURE AND TECHNOLOGY
Bunawan, Agusan del Sur
Doc No.: F-DOI-018
website: http://asscat.edu.ph Effective Date: 08/25/2017
email address: op@asscat.edu.ph; mobile no.: +639486379266 Rev No.: 0
Page No.: 6 of 7
19084895
TEST QUESTIONNAIRE
25.
26.
27.
AGUSAN DEL SUR STATE COLLEGE OF AGRICULTURE AND TECHNOLOGY
Bunawan, Agusan del Sur
Doc No.: F-DOI-018
website: http://asscat.edu.ph Effective Date: 08/25/2017
email address: op@asscat.edu.ph; mobile no.: +639486379266 Rev No.: 0
Page No.: 7 of 7
19084895
TEST QUESTIONNAIRE
28.
******nothing follows******