Professional Documents
Culture Documents
27 Ensign
I suggest to take a look at the 3D printed kit tutorial, which is downloadable at the
following link.
http://one-man-model.main.jp/index.html
Printed in Japan
ABS and HIPS filament for 3D printers Made in Taiwan or China
1
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
C2 C1
C3R
C3L
Among the above image‘→’ mean Φ0.8 (1/48 Φ1.2) L4 brass rod
D3A
F5A
D4B
L23
Optional:φ0.8 L6
(1/48φ0.8 L9) D4A
brass rod.
2
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
B-B
F3 or F2R F3
F3 or F2L
L22X27set
B A
F5B
B A D9 F5A L24
L24
Please check fitting between inside and fuselage before connection by glue!!
When the wall and floor assembly is tight, please sand inside wall&floor edge!!
3
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
2.2 Forward fuselage
Before erection, removing inside and outside burr is necessary.
1 Inside painting
2 Parts assembling
3 Window clear tape from OUTSIDE
4 Window clear sheet from INSIDE
5 Window masking for later exterior painting
6 A1A and A1B connection
D8A
A1B
L1A
L1BL
Among the above image‘→’ mean Φ0.8 (1/48 Φ1.2) L4 brass rod
Sticker is paintable after lamination!!
4
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
A2R
A2L
Among the above image‘→’ mean Φ0.8 (1/48 Φ1.2) L4 brass rod
〇: N3&P8, 〇: N4&P6, 〇: N2&P10, 〇: N5&P7
□: N2&P8, □: N2&P9, □: N2&P11, □: N2&P12
5
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
K2
L4L
L3L L2L
Sticker is paintable. Please laminate masking tape on the window before painting.
Please check fitting between inside and fuselage before connection by glue!!
When the wall and floor assembly is tight, please sand inside wall&floor edge!!
6
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
2.4 rear unit
D2B
D2A
Among the above image‘→’ mean Φ0.8 L 7 (1/48Φ1.2 L10.5) brass rod
Do not glue shaft with tire please!! Flat area position adjustment will be needed later.
B4
Vice versa
D2
A3
Among the above image‘→’mean Φ1.2 L25 brass rod (1/48 Φ1.2 L37.5 bamboo)
Among the above image‘→’mean Φ1.2 L20 brass rod (1/48 Φ1.2 L30 bamboo)
Among the above image‘→’mean Φ0.8 L12 brass rod (1/48 Φ1.2 L18)
7
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
2.5 main wing unit
1 engine
2 engine sub assembly
Please paint engine and inside cowling beforehand.
3 wing connection
G1 Optional: φ0.6 L6 to 7
(1/48φ0.8 L9 to 10.5)
brass rod.
Vice versa
B2R
B3R
B1R
Among the above image‘→’ mean Φ2 L20 bamboo rod (1/48 Φ3 L30)
Among the above image‘→’ mean Φ1 L5 PS rod (1/48 Φ1.8 L7.5 bamboo)
Outer main wing “B3” can be separable even after completion!!
8
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
Ensign 2 R-1820 engined version
G1
G2
Vice versa
B2R
B3R
B1R
Among the above image‘→’ mean Φ2 L20 bamboo rod (1/48 Φ3 L30)
Among the above image‘→’ mean Φ1 L5 PS rod (1/48 Φ1.8 L7.5 bamboo)
Outer main wing “B3” can be separable even after completion!!
Vice versa
φ1.8 L10(1/48φ2.5 L15)
Aluminum wire
9
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
2.6 Fuselage and wing connection
L5 L6 L7
L8
10
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
L10 L11
D7 K3 φ0.8L23(1/48φ1.2L34.5)
D6
brass rod.
D5 D5
X4
11
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
Undercarriage cover closed ver.
φ0.8 L22 brass
X2 (1/48φ1.2 L33)
X2
10
D1C
5
D1C E4C
Vice versa!!
φ0.8 L15 brass
15=10+5
(1/48φ1.2 L22.5)
Vice versa!!
2 pairs
Main undercarriage
E3R
E2R
D1O
Among the above image‘←’mean Φ0.8 L5 (1/48 Φ1.2 L7.5) brass rod
‘←’ mean Φ0.8 L14 (1/48 Φ1.2 L21) brass rod (implant 5mm)
‘--’ mean Φ0.8 L16 (1/48 Φ0.8 L24) brass rod
‘--’ mean Φ0.6 L14 (1/48 Φ0.8 L21) brass rod
12
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
E4L
Vice versa!!
Stopper rod
φ0.8 L15 brass
15=7+8
(1/48φ1.2 L22.5)
2.8 Door open position (optional)
Please refer these links.
http://aviadejavu.ru/Site/Crafts/Craft21568.htm
http://www.airwar.ru/enc/cw1/ensign.html
As for outside character, please refer the following link. I know that Ensign, Euterpe and Echo
were modified to the Ensign 2. As for Ensign 2 markings, I do not know well.
https://www.airport-
data.com/search/search2.html?field=model&search=Search&code=Armstrong+Whitworth+AW27+Ensign+2
13
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
Ensign 1 painting and sticking examples are as follows. Sticker ‘L21’is optional.
M1
M4
G-ADSR ENSIGN
M3
L21(optional)
ENSIGN G-ADSR
Tail
Number Alt. Code Type Serial Location
G-ADSR Ensign Ensign 1 later Ensign 2 AW1156 United Kingdom
G-ADSS Egeria Ensign 1 AW1157 United Kingdom
G-ADST Elsinore Ensign 1 AW1158 United Kingdom
G-ADSU Euterpe Ensign 1 later Ensign 2 AW1159 United Kingdom
G-ADSV Explorer Ensign 1 AW1160 United Kingdom
G-ADSW Eddystone Ensign 1 AW1161 United Kingdom
G-ADSX Ettrick Ensign 1 AW1162 United Kingdom
G-ADSY Empyrean Ensign 1 AW1163 United Kingdom
G-ADSZ Elysian Ensign 1 AW1164 United Kingdom
G-ADTA Euryalus Ensign 1 AW1165 United Kingdom
G-ADTB Echo Ensign 1 later Ensign 2 AW1166 United Kingdom
G-ADTC Endymion Ensign 1 AW1167 United Kingdom
G-AFZU Everest Ensign 2 AW1821 United Kingdom
G-AFZV Enterprise Ensign 2 AW1822 France
F-AFZV Vichy France Daimler-Benz engines
F-BAHD Luftwaffe
14
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
Sorry, I do not know Ensign 2 markings.
Sticker surface is paintable!!
M2
G-A DSR
G-A DSR
15
‘L’ mean length in this instruction
One Man Model 1/72 scale A.W.27 Ensign
16
‘L’ mean length in this instruction