Professional Documents
Culture Documents
HCPL-3150 (Single Channel), HCPL-315J (Dual Channel) : Data Sheet
HCPL-3150 (Single Channel), HCPL-315J (Dual Channel) : Data Sheet
Overview Features
The Broadcom® HCPL-315X consists of an LED optically 0.6A maximum peak output current
coupled to an integrated circuit with a power output stage. 0.5A minimum peak output current
This optocoupler is ideally suited for driving power IGBTs 15-kV/µs minimum Common Mode Rejection (CMR) at
and MOSFETs used in motor control inverter applications. VCM = 1500V
The high operating voltage range of the output stage 1.0V maximum low level output voltage (VOL)
provides the drive voltages required by gate-controlled eliminates need for negative gate drive
devices. The voltage and current supplied by this ICC = 5 mA maximum supply current
optocoupler makes it ideally suited for directly driving IGBTs Under voltage lock-out protection (UVLO) with
with ratings up to 1200V/50A. For IGBTs with higher ratings, hysteresis
the HCPL-3150/315J can be used to drive a discrete power Wide operating VCC range: 15V to 30V
stage which drives the IGBT gate. 0.5-µs maximum propagation delay
±0.35-µs maximum delay between devices/channels
Applications Industrial temperature range: –40°C to 100°C
Isolated IGBT/MOSFET gate drive HCPL-315J: channel one to channel two output
isolation = 1500 Vrms/1 min.
AC and brushless DC motor drives
Safety and regulatory approval:
Industrial inverters
– UL recognized (UL1577),
Switch mode power supplies (SMPSs)
3750 Vrms/1 min. (HCPL-3150)
Uninterruptable power supplies (UPSs)
5000 Vrms/1 min. (HCPL-315J)
– IEC/EN/DIN EN 60747-5-5 approved
VIORM = 630 Vpeak (HCPL-3150 option 060 only)
VIORM = 1414 Vpeak (HCPL-315J) CSA certified
CAUTION! It is advised that normal static precautions be taken in handling and assembly of this component to prevent
damage and/or degradation that may be induced by ESD. The components featured in this data sheet are not
to be used in military or aerospace applications or environments.
Broadcom AV02-0164EN
October 20, 2017
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Functional Diagram
N/C 1 16 VCC
ANODE 2 15 VO
N/C 1 8 VCC TRUTH TABLE
CATHODE 3 14 VEE VCC – VEE VCC – VEE
SHIELD POSITIVE-GOING NEGATIVE-GOING VO
ANODE VO LED
2 7
(i.e. TURN-ON) (i.e. TURN-OFF)
OFF 0 - 30 V 0 - 30 V LOW
CATHODE 3 6 VO ANODE 6 11 VCC
ON 0 - 11 V 0 - 9.5 V LOW
CATHODE 7 10 VO ON 11 - 13.5 V 9.5 - 12 V TRANSITION
N/C 4 5 VEE ON 13.5 - 30 V 12 - 30 V HIGH
SHIELD N/C 8 9 VEE
SHIELD
HCPL-3150 HCPL-315J
NOTE: A 0.1-µF bypass capacitor must be connected between the VCC and VEE pins for each channel.
Broadcom AV02-0164EN
2
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Ordering Information
HCPL-3150 is UL Recognized with 3750 Vrms for 1 minute per UL1577. HCPL-315J is UL Recognized with 5000 Vrms for
1 minute per UL1577.
Option
To order, choose a part number from the part number column and combine with the desired option from the option column
to form an order entry.
Example 1:
HCPL-3150-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
HCPL-3150 to order product of 300 mil DIP package in tube packaging and non RoHS compliant.
Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information.
NOTE: The notation “#XXX” is used for existing products, while (new) products launched since July 15, 2001 and RoHS
compliant option use “-XXXE.”
Broadcom AV02-0164EN
3
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Broadcom AV02-0164EN
4
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
1 3
Code
Pin 1 Dot 2 4
1.080 ± 0.320
(0.043 ± 0.013) 0.635 ± 0.25
(0.025 ± 0.010)
0.635 ± 0.130 12 ° NOM.
2.54
(0.100) (0.025 ± 0.005)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX.
Broadcom AV02-0164EN
5
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
TYPE NUMBER
DATE CODE
AVAGO A XXXX
LEAD-FREE YYWW 7.493 ± 0.254 11.63 (0.458)
EEE (0.295 ± 0.010)
PIN 1 DOT
LOT ID
2.16 (0.085)
1 2 3 6 7 8
10.312 ± 0.254
(0.406 ± 0.10)
8.763 ± 0.254 ALL LEADS TO
9° (0.345 ± 0.010) BE COPLANAR
± 0.05 (0.002)
Regulatory Information
The HCPL-3150 and HCPL-315J have been approved by the following organizations.
Broadcom AV02-0164EN
6
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
NOTE: Isolation characteristics are guaranteed only within the safety maximum ratings that must be ensured by protective
circuits in application.
Broadcom AV02-0164EN
7
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Option 300 – surface mount classification is Class A in accordance with CECC 00802.
Peak Transient Input Current (<1-µs pulse width, 300 pps) IF(TRAN) — 1.0 A
Reverse Input Voltage VR — 5 Volts
“High” Peak Output Current IOH(PEAK) — 0.6 A b, c
Lead Solder Temperature 260°C for 10 seconds, 1.6 mm below seating plane
Solder Reflow Temperature Profile See Package Outline Drawings Section
a. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA/°C.
b. Each channel.
c. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
minimum = 0.5A. See the Applications section for additional details on limiting IOH peak.
d. Derate linearly above 70°C free-air temperature at a rate of 4.8 mW/°C.
e. Derate linearly above 70°C free-air temperature at a rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed 125°C.
Broadcom AV02-0164EN
8
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Broadcom AV02-0164EN
9
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Parameter Symbol Min. Typ.a Max. Units Test Conditions Figure Note
High Level Output Current IOH 0.1 0.4 — A VO = (VCC – 4V) 2, 3, 5
0.5 — — VO = (VCC – 15V) 17 b
Broadcom AV02-0164EN
10
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Parameter Symbol Min. Typ.a Max. Units Test Conditions Figure Note
Propagation Delay Time to High tPLH 0.10 0.30 0.50 µs Rg = 47 Ω, Cg = 3 nF, 10, 11, b
Output Level f = 10 kHz, Duty Cycle = 50% 12, 13,
Propagation Delay Time to Low tPHL 0.10 0.3 0.50 µs 14, 23
Output Level
Pulse Width Distortion PWD 0.3 µs c
Broadcom AV02-0164EN
11
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Package Characteristics
Each channel, unless otherwise specified.
Parameter Symbol Device Min. Typ.a Max. Units Test Conditions Figure Note
Input-Output Momentary VISO HCPL-3150 3750 — — Vrms RH < 50%, t = 1 min., c, d
Broadcom AV02-0164EN
12
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 1: VOH vs. Temperature Figure 2: IOH vs. Temperature Figure 3: VOH vs. IOH
0 0.50 -1
IF = 7 to 16 mA IF = 7 to 16 mA
(VOH - VCC ) – HIGH OUTPUT VOLTAGE DROP – V
0.40 -3
-2
0.35 -4
-3 IF = 7 to 16 mA
0.30 -5 VCC = 15 to 30 V
VEE = 0 V
-4 0.25 -6
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 0 0.2 0.4 0.6 0.8 1.0
TA – TEMPERATURE – °C TA – TEMPERATURE – °C IOH – OUTPUT HIGH CURRENT – A
Figure 4: VOL vs. Temperature Figure 5: IOL vs. Temperature Figure 6: VOL vs. IOL
1.0 1.0 5
VF(OFF) = -3.0 to 0.8 V VF(OFF) = -3.0 to 0.8 V
IOUT = 100 mA VCC = 15 to 30 V
0.8 VCC = 15 to 30 V 0.8 4 VEE = 0 V
IOL – OUTPUT LOW CURRENT – A
VEE = 0 V
0.6 0.6 3
0.4 0.4 2
VF(OFF) = -3.0 to 0.8 V
VOUT = 2.5 V
0.2 0.2 1 100 °C
VCC = 15 to 30 V
VEE = 0 V 25 °C
-40 °C
0 0 0
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 0 0.2 0.4 0.6 0.8 1.0
Figure 7: ICC vs. Temperature Figure 8: ICC vs. VCC Figure 9: IFLH vs. Temperature
3.5 3.5 5
ICCH ICCH VCC = 15 TO 30 V
IFLH – LOW TO HIGH CURRENT THRESHOLD – mA
3
2.5 2.5
2
VCC = 30 V IF = 10 mA for ICCH
2.0 VEE = 0 V 2.0 IF = 0 mA for ICCL
IF = 10 mA for ICCH 1
TA = 25 °C
IF = 0 mA for ICCL VEE = 0 V
1.5 1.5 0
-40 -20 0 20 40 60 80 100 15 20 25 30 -40 -20 0 20 40 60 80 100
TA – TEMPERATURE – °C VCC – SUPPLY VOLTAGE – V TA – TEMPERATURE – °C
Broadcom AV02-0164EN
13
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 10: Propagation Delay vs. VCC Figure 11: Propagation Delay vs. IF Figure 12: Propagation Delay vs.
Temperature
Tp – PROPAGATION DELAY – ns
Tp – PROPAGATION DELAY – ns
400 Cg = 3 nF 400 DUTY CYCLE = 50% 400 Rg = 47 :, Cg = 3 nF
DUTY CYCLE = 50% f = 10 kHz DUTY CYCLE = 50%
f = 10 kHz f = 10 kHz
Figure 13: Propagation Delay vs. Rg Figure 14: Propagation Delay vs. Cg Figure 15: Transfer Characteristics
500 500 30
VCC = 30 V, VEE = 0 V VCC = 30 V, VEE = 0 V
TA = 25 °C TA = 25 °C
IF = 10 mA 25
IF = 10 mA
Tp – PROPAGATION DELAY – ns
400 Cg = 3 nF
Tp – PROPAGATION DELAY – ns
400 Rg = 47 :
VO – OUTPUT VOLTAGE – V
DUTY CYCLE = 50% DUTY CYCLE = 50% 20
f = 10 kHz f = 10 kHz
300 300 15
10
200 200
TPLH TPLH 5
TPHL TPHL
100 100 0
0 50 100 150 200 0 20 40 60 80 100 0 1 2 3 4 5
Rg – SERIES LOAD RESISTANCE – : Cg – LOAD CAPACITANCE – nF IF – FORWARD LED CURRENT – mA
1000
TA = 25°C
100
IF
IF – FORWARD CURRENT – mA
10 +
VF
–
1.0
0.1
0.01
0.001
1.10 1.20 1.30 1.40 1.50 1.60
VF – FORWARD VOLTAGE – V
Broadcom AV02-0164EN
14
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 17: IOH Test Circuit Figure 18: IOL Test Circuit
1 8 1 8
0.1 μF 0.1 μF
IOL
+ 4V
2 7 – 2 7
+ VCC = 15
IF = 7 to + VCC = 15 – to 30 V
16 mA – to 30 V
3 6 3 6 2.5 V +
–
IOH
4 5 4 5
Figure 19: VOH Test Circuit Figure 20: VOL Test Circuit
1 8 1 8
0.1 μF 0.1 μF
100 mA
VOH 2 7
2 7
IF = 7 to + VCC = 15 + VCC = 15
16 mA – – to 30 V
to 30 V
3 6 3 6
VOL
100 mA
4 5 4 5
Figure 21: IFLH Test Circuit Figure 22: UVLO Test Circuit
1 8 1 8
0.1 μF 0.1 μF
2 7 2 7
IF + VCC = 15 IF = 10 mA +
– – VCC
VO > 5 V to 30 V VO > 5 V
3 6 3 6
4 5 4 5
Broadcom AV02-0164EN
15
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 23: tPLH, tPHL, tr, and tf Test Circuit and Waveforms
1 8
0.1 μF IF
IF = 7 to 16 mA VCC = 15
+ to 30 V
2 7 –
500 : tr tf
+ VO
10 KHz – 90%
50% DUTY 3 6 47 :
CYCLE 50%
3 nF VOUT 10%
4 5
tPLH tPHL
VCM
GV VCM
1 8 =
IF Gt 't
A 0.1 μF
0V
2 7
B
+ + 't
5V VO –
–
VCC = 30 V
3 6 VOH
VO
SWITCH AT A: IF = 10 mA
4 5
VO VOL
SWITCH AT B: IF = 0 mA
+
–
VCM = 1500 V
Applications Information
Eliminating Negative IGBT Gate Drive
To keep the IGBT firmly off, the HCPL-3150/315J has a very low maximum VOL specification of 1.0V. The HCPL-3150/315J
realizes this very low VOL by using a DMOS transistor with 4Ω (typical) on resistance in its pull-down circuit. When the
HCPL3150/315J is in the low state, the IGBT gate is shorted to the emitter by Rg + 4Ω. Minimizing Rg and the lead
inductance from the HCPL-3150/315J to the IGBT gate and emitter (possibly by mounting the HCPL-3150/315J on a small
PC board directly above the IGBT) can eliminate the need for negative IGBT gate drive in many applications as shown in
Figure 25 and Figure 26. Care should be taken with such a PC board design to avoid routing the IGBT collector or emitter
traces close to the HCPL-3150/315J input as this can result in unwanted coupling of transient signals into the HCPL-3150/
315J and degrade performance. (If the IGBT drain must be routed near the HCPL-3150/315J input, then the LED should be
reverse-biased when in the off state, to prevent the transient signals coupled from the IGBT drain from turning on the HCPL-
3150/315J.)
Broadcom AV02-0164EN
16
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
+5 V HCPL-3150
1 8
VCC = 18 V + HVDC
270 : 0.1 μF +
–
2 7
Rg
CONTROL Q1 3-PHASE
INPUT 3 6 AC
74XXX
OPEN 4 5
COLLECTOR
Q2 - HVDC
HCPL-315J + HVDC
+5 V FLOATING
1 16 SUPPLY
270 : VCC = 18 V
CONTROL 0.1 μF +
INPUT –
2 15
74XX Rg
OPEN
COLLECTOR
3 14
GND 1 3-PHASE
AC
+5 V
6 11
VCC = 18 V
270 : 0.1 μF +
CONTROL –
INPUT 7 10
Rg
74XX
OPEN
8 9
COLLECTOR
GND 1 - HVDC
Broadcom AV02-0164EN
17
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 27: HCPL-3150 Typical Application Circuit with Negative IGBT Gate Drive
+5 V HCPL-3150
1 8
VCC = 15 V + HVDC
270 : 0.1 μF +
–
2 7
Rg
CONTROL Q1 3-PHASE
3 6 AC
INPUT VEE = -5 V
–
+
74XXX
OPEN 4 5
COLLECTOR
Q2 - HVDC
Broadcom AV02-0164EN
18
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 28: HCPL-315J Typical Application Circuit with Negative IGBT Gate Drive
HCPL-315J + HVDC
+5 V FLOATING
1 16 SUPPLY
270 : VCC = 15 V
CONTROL 0.1 μF +
INPUT –
2 15
74XX Rg
OPEN
COLLECTOR
3 14 –
+
VEE = -5 V
GND 1 3-PHASE
AC
+5 V
6 11
VCC = 15 V
270 : 0.1 μF +
CONTROL –
INPUT 7 10
Rg
74XX
OPEN
8 9 –
COLLECTOR +
VCC = -5 V
GND 1 - HVDC
Broadcom AV02-0164EN
19
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
The value of 4.25 mA for ICC in the previous equation was Thermal Model (HCPL-3150)
obtained by derating the ICC max of 5 mA (which occurs at
–40°C) to ICC max at 90°C (see Figure 7). The steady state thermal model for the HCPL-3150 is
shown in Figure 29. The thermal resistance values given in
Since PO for this case is greater than PO(MAX), Rg must be this model can be used to calculate the temperatures at
increased to reduce the HCPL-3150 power dissipation. each node for a given operating condition. As shown by the
model, all heat generated flows through θCA which raises
PO(SWITCHING MAX) = PO(MAX) - PO(BIAS) the case temperature TC accordingly. The value of θCA
= 154 mW - 85 mW depends on the conditions of the board design and is,
therefore, determined by the designer. The value of θCA =
= 69 mW 83°C/W was obtained from thermal measurements using a
2.5 in. × 2.5 in. PC board, with small traces (no ground
PO(SWITCHINGMAX) plane), a single HCPL-3150 soldered into the center of the
ESW(MAX) =
f board and still air. The absolute maximum power dissipation
derating specifications assume a θCA value of 83°C/W.
= 69 mW = 3.45 μJ
20 kHz
TLD = 439°C/W
Broadcom AV02-0164EN
20
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
From the thermal mode in Figure 29, the LED and detector Thermal Model Dual-Channel (SOIC-16)
IC junction temperatures can be expressed as:
HCPL-315J Optoisolator
TJE = PE x (TLC||(TLD + TDC) + TCA)
Definitions
+ PD x ( TLC x TDC
TLC + TDC + TLD
+ TCA + TA )
θ1, θ2, θ3, θ4, θ5, θ6, θ7, θ8, θ9, θ10: Thermal impedances
between nodes as shown in Figure 30. Ambient
TJD = PE ( T T+ T T + T
LC
LC
x
DC
DC LD
+ TCA ) Temperature: Measured approximately 1.25 cm above the
optocoupler with no forced air.
+ PDx (TDC||(TLD + TLC) + TCA) + TA
Figure 30: Thermal Impedance Model for HCPL-315J
LED 1 T1 LED 2
Inserting the values for θLC and θDC shown in Figure 29
gives: T2 T3
DETECTOR 1 DETECTOR 2
TJE and TJD should be limited to 125°C based on the board Figure 31: Power Dissipation
layout and part placement (θCA) specific to the application.
PE1 PD1
PE2 PD2
Description
This thermal model assumes that a 16-pin dual-channel
(SOIC-16) optocoupler is soldered into an 8.5 cm × 8.1 cm
printed circuit board (PCB). These optocouplers are hybrid
devices with four die: two LEDs and two detectors. The
temperature at the LED and the detector of the optocoupler
can be calculated by using the equations below.
Broadcom AV02-0164EN
21
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
where:
ΔTE1A = Temperature difference between ambient and LED 1
ΔTE2A = Temperature difference between ambient and LED 2
ΔTD1A = Temperature difference between ambient and detector 1
ΔTD2A = Temperature difference between ambient and detector 2
PE1 = Power dissipation from LED 1;
PE2 = Power dissipation from LED 2;
PD1 = Power dissipation from detector 1;
PD2 = Power dissipation from detector 2
Axy thermal coefficient (units in °C/W) is a function of thermal impedances θ1 through θ10.
Part Number A11, A22 A12, A21 A13, A31 A24, A42 A14, A41 A23, A32 A33, A44 A34, A43
HCPL-315J 198 64 62 64 83 90 137 69
Broadcom AV02-0164EN
22
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
LED Drive Circuit Considerations CMR with the LED Off (CMRL)
for Ultra High CMR Performance A high CMR LED drive circuit must keep the LED off (VF ≤
VF(OFF)) during common mode transients. For example,
Without a detector shield, the dominant cause of
during a –dVCM/dt transient in Figure 35, the current flowing
optocoupler CMR failure is capacitive coupling from the
through CLEDP also flows through the RSAT and VSAT of the
input side of the optocoupler, through the package, to the
logic gate. As long as the low state voltage developed
detector IC as shown in Figure 33. The HCPL-3150/315J
across the logic gate is less than VF(OFF), the LED will
improves CMR performance by using a detector IC with an
remain off and no common mode failure will occur.
optically transparent Faraday shield, which diverts the
capacitively coupled current away from the sensitive IC The open collector drive circuit, shown in Figure 36, cannot
circuitry. How ever, this shield does not eliminate the keep the LED off during a +dVCM/dt transient, since all the
capacitive coupling between the LED and optocoupler pins current flowing through CLEDN must be supplied by the LED,
5 to 8 as shown in Figure 34. This capacitive coupling and it is not recommended for applications requiring
causes perturbations in the LED current during common ultra-high CMRL performance. Figure 37 is an alternative
mode transients and becomes the major source of CMR drive circuit which, like the recommended application circuit
failures for a shielded optocoupler. The main design (Figure 25 and Figure 26), does achieve ultra-high CMR
objective of a high CMR LED drive circuit becomes keeping performance by shunting the LED in the off state.
the LED in the proper state (on or off) during common mode
transients. For example, the recommended application Under Voltage Lockout Feature
circuit (Figure 25 and Figure 26), can achieve 15kV/µs CMR
while minimizing component complexity. The HCPL-3150/315J contains an under voltage lockout
(UVLO) feature that is designed to protect the IGBT under
Techniques to keep the LED in the proper state are
fault conditions that cause the HCPL-3150/315J supply
discussed in the next two sections.
voltage (equivalent to the fully-charged IGBT gate voltage)
to drop below a level necessary to keep the IGBT in a low
CMR with the LED On (CMRH) resistance state. When the HCPL-3150/315J output is in the
high state and the supply voltage drops below the
A high CMR LED drive circuit must keep the LED on during
HCPL-3150/315J VUVLO- threshold (9.5 < VUVLO- < 12.0),
common mode transients. This is achieved by overdriving
the optocoupler output will go into the low state with a typical
the LED current beyond the input threshold so that it is not
delay, UVLO Turn Off Delay, of 0.6 µs. When the
pulled below the threshold during a transient. A minimum
HCPL-3150/315J output is in the low state and the supply
LED current of 10 mA provides adequate margin over the
voltage rises above the HCPL-3150/315J VUVLO+ threshold
maximum IFLH of 5 mA to achieve 15kV/µs CMR.
(11.0 < VUVLO+ < 13.5), the optocoupler will go into the high
state (assuming LED is “ON”) with a typical delay, UVLO
Figure 32: Energy Dissipated in the HCPL-3150 for Each IGBT
Switching Cycle. TURN On Delay, of 0.8 µs.
7
Qg = 100 nC
6
Esw – ENERGY PER SWITCHING CYCLE – μJ
Qg = 250 nC
Qg = 500 nC
5
VCC = 19 V
4
VEE = -9 V
3
0
0 20 40 60 80 100
Rg – GATE RESISTANCE – :
Broadcom AV02-0164EN
23
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 33: Optocoupler Input to Output Capacitance Model Figure 34: Optocoupler Input to Output Capacitance Model
for Unshielded Optocouplers for Shielded Optocouplers
1 8 1 CLEDO1 8
CLEDP CLEDP
2 7 2 7
CLEDO2
3 6 3 6
CLEDN CLEDN
4 5 4 5
SHIELD
Figure 35: Equivalent Circuit for Figure 25 During Common Mode Transient
+5 V 1 8
0.1
CLEDP μF +
– VCC = 18 V
+ 2 7
ILEDP
VSAT
–
3 6 •••
CLEDN
Rg
4 5 •••
SHIELD
+ –
Broadcom AV02-0164EN
24
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 36: Not Recommended Open Collector Drive Circuit Figure 37: Recommended LED Drive Circuit for Ultra-High CMR
1 8 1 8
+5 V +5 V
CLEDP CLEDP
2 7 2 7
3 6 3 6
Q1 CLEDN CLEDN
ILEDN
4 5 4 5
SHIELD SHIELD
Figure 38: Minimum LED Skew for Zero Dead Time Figure 39: Waveforms for Dead Time
ILED1 ILED1
VOUT1 VOUT1
Q1 ON Q1 ON
Q1 OFF Q1 OFF
Q2 ON Q2 ON
Q2 OFF VOUT2 Q2 OFF
VOUT2
ILED2 ILED2
tPHL MAX tPHL MIN
tPLH MIN tPHL MAX
PDD* MAX = (tPHL- tPLH)MAX = tPHL MAX - tPLH MIN tPLH
MIN
*PDD = PROPAGATION DELAY DIFFERENCE tPLH MAX
NOTE: FOR PDD CALCULATIONS THE PROPAGATION DELAYS
ARE TAKEN AT THE SAME TEMPERATURE AND TEST CONDITIONS. (tPHL-tPLH) MAX
= PDD* MAX
Broadcom AV02-0164EN
25
HCPL-3150 (Single Channel),
HCPL-315J (Dual Channel) Data Sheet 0.5 Amp Output Current IGBT Gate Drive Optocoupler
Figure 40: Under Voltage Lock Out Figure 41: HCPL-3150: Thermal Figure 42: HCPL-315J: Thermal
Derating Curve, Dependence of Safety Derating Curve, Dependence of Safety
Limiting Value with Case Temperature Limiting Value with Case Temperature
per IEC/EN/DIN EN 60747-5-5 per IEC/EN/DIN EN 60747-5-5
14 800 1400
PS (mW) PSI OUTPUT
700
10 1000
(10.7, 9.2)
PSI – POWER – mW
500
8 800
400
6 600
300
4 400
200
2 100 200
(10.7, 0.1) (12.3, 0.1)
0 0 0
0 5 10 15 20 0 25 50 75 100 125 150 175 200 0 25 50 75 100 125 150 175 200
(VCC - VEE ) – SUPPLY VOLTAGE – V TS – CASE TEMPERATURE – °C TS – CASE TEMPERATURE – °C
Broadcom AV02-0164EN
26
Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks
of Broadcom and/or its affiliates in the United States, certain other countries and/or the EU.
The term “Broadcom” refers to Broadcom Limited and/or its subsidiaries. For more information, please visit
www.broadcom.com.
Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability,
function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does
not assume any liability arising out of the application or use of this information, nor the application or use of any product or
circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
Mouser Electronics
Authorized Distributor
Avago Technologies:
HCPL-3150#300 HCPL-3150#360 HCPL-3150#500 HCPL-3150#560 HCPL-3150-300E HCPL-3150-360E HCPL-
3150-500E HCPL-3150-560E