Professional Documents
Culture Documents
net/publication/340900099
CITATIONS READS
0 14,557
1 author:
Muslim Ali
University of Kerbala
67 PUBLICATIONS 127 CITATIONS
SEE PROFILE
Some of the authors of this publication are also working on these related projects:
All content following this page was uploaded by Muslim Ali on 24 April 2020.
The piston is a reciprocating part of IC engine that performs a number of functions. The main
functions of the piston are as follows:
(1) It transmits the force due to gas pressure inside the cylinder to the crankshaft through the
connecting rod.
(3) It seals the inside portion of the cylinder from the crankcase by means of piston rings.
(4) It takes the side thrust resulting from obliquity of the connecting rod.
(5) It dissipates large amount of heat from the combustion chamber to the cylinder wall.
Trunk type piston, as shown in Fig. 1, is used in IC engines. It consists of the following parts:
It is the top portion of the piston which withstands the gas pressure inside the cylinder. It has flat,
concave or convex shape depending upon the construction of combustion chamber.
Fig. 1 Piston
2. Piston Rings
They act as seal and prevent the leakage of gas past the piston. Piston rings are also called
‘compression’ rings.
It prevents the leakage of lubricating oil past the piston into the combustion chamber.
3. Piston Skirt
It is the lower part of the piston below the piston rings which acts as bearing surface for the side
thrust exerted by the connecting rod.
4. Piston Pin
It connects the piston to the connecting rod. It is also called ‘gudgeon’ pin or ‘wrist’ pin.
(i) It should have sufficient strength to withstand the force due to combustion of fuel and also the
inertia forces due to reciprocating parts.
(ii) It should have sufficient rigidity to withstand thermal and mechanical distortions.
(iii) It should have adequate capacity to dissipate the heat from the crown to the cylinder wall
through the piston rings and the skirt.
(iv) It should have minimum weight to reduce the inertia force due to reciprocating motion.
(v) It should form an efficient seal to prevent leakage of flue gases from combustion chamber to
the crankcase past the piston. It should also prevent leakage of lubricating oil into the
combustion chamber past the piston.
(vi) It should have sufficient bearing area to take the side thrust and prevent undue wear.
PISTON MATERIALS
Commonly used materials for IC engine pistons are cast iron, cast steel, forged steel, cast
aluminum alloys and forged aluminum alloy. Compared with cast iron, aluminum alloy pistons
have the following advantages:
(i) The thermal conductivity of aluminum alloys is approximately three times that of cast iron.
Therefore, an aluminum alloy piston has less variation in temperature from the crown to the
piston rings.
(ii) The density of aluminum alloy is about one third that of cast iron. This result in light weight
construction and reduces inertia forces. Cast iron pistons offer the following advantages:
(i) Cast iron pistons have higher strength compared with aluminum alloy pistons. As the
temperature increases, the strength of aluminum alloy piston decreases rapidly compared with
cast iron piston. Due to higher strength, it is possible to provide thin sections for the parts of cast
iron piston.
(ii) The wear strength of a cast iron piston is more than corresponding aluminum alloy piston.
(iii) The coefficient of thermal expansion of aluminum alloy is approximately twice that of cast
iron. Therefore, aluminum alloy pistons need more clearance between the cylinder wall and
piston rings. Cast iron pistons are used for moderately rated engines with piston speed below 6
m/s. Aluminum alloy pistons are used for highly rated engines with piston speeds above 6 m/s.
There are two types of piston heads-flat plate type and cup type as shown in Fig. 2. The selection
of the type depends upon the required volume for combustion chamber and the arrangement of
valves.
Fig. 2 Types of piston head
There are two criteria for calculating the thickness of piston head-strength and heat dissipation.
On the basis of strength criterion, the piston head is treated as a flat circular plate of uniform
thickness fixed at the outer edge and subjected to uniformly distributed gas pressure (pmax.) over
the entire surface area. According to Grashoff’s formula, the thickness of the piston head is given
by,
(1)
Where,
= thickness of piston head (mm)
D = cylinder bore (mm)
. = maximum gas pressure or explosion pressure (MPa or N/mm2)
= permissible bending stress (N/mm2)
Note
(i) The bending stress ( ) in Eq. (1) is the allowable tensile stress ( ). Since the material of the
cylinder head is brittle,
= =
(ii) In examples where ultimate tensile strength of the piston material and factor of
safety are not specified, the allowable bending stress ( ) for grey cast iron is taken
from 35 to 40 N/ . For aluminum alloy, it can be assumed from 50 to 90
N/ .
(iii) The maximum gas pressure ( ) may rise up to 8 MPa. The average value
of maximum gas pressure is taken as 4 to 5 MPa or N/ . There is an empirical
formula recommended by Held and Favary for the thickness of the piston head.
The piston head absorbs the heat during combustion of fuel and transmits it to the
cylinder wall. It should have sufficient thickness to quickly transfer the heat to the
cylinder wall. On the basis of heat dissipation, the thickness of the piston head is
given by,
[ ( )
]x (3)
Where,
The amount of heat conducted through piston head (H) is given by,
H = [ C x HCV x m x BP ] x (4)
where,
C is the ratio of heat absorbed by the piston to the total heat developed in the
cylinder (C = 5% or C = 0.05)
Note
m=[ ] kg/kW/s
The piston head is provided with a number of ribs for the following reasons:
(i) Ribs strengthen the piston head against the gas pressure. They increase the
rigidity and prevent distortion of piston head.
(ii) Ribs transmit a large portion of combustion heat from the piston head to the
piston rings. This reduces the temperature difference between the centre and edge
of piston head.
(iii) The side thrust created by obliquity of connecting rod is transmitted to the
piston at the piston pin. It is then transmitted to the cylinder wall through the skirt.
The stiffening rib provided at the centre of boss and extending around the skirt,
distributes the side thrust more uniformly and prevents distortion of the skirt.
(i) When the thickness of the piston head is 6 mm or less, no ribs are required.
When the thickness of the piston head is more than 6 mm, a suitable number of ribs
are required.
(no ribs)
= ( ) to ( ) (7)
where,
A cup provides additional space for combustion of fuel. Provision of cup at the top
of the piston head depends upon the volume of combustion chamber. It also
depends upon the arrangement of valves. If inlet and exhaust valves open and close
at angles near the top dead centre, then there is possibility that either inlet or
exhaust valve may strike the piston top due to overtaking. A spherical cavity in the
form of cup is provided for this purpose.
(i) When the ratio of stroke length to bore ( ) is up to 1.5, a cup is required on the
top of the piston.
PISTON RINGS
In IC engines, two types of piston rings are used, viz., compression rings and oil
scraper rings. The main function of compression rings is to maintain a seal
between the cylinder wall and piston and prevent leakage of gas past the piston.
They also transfer heat from the piston head to the cylinder wall. Piston rings also
absorb fluctuations in side thrust. Oil scraper rings or oil control rings are provided
below the compression rings. They provide proper lubrication of the cylinder liner
and reduce frictional losses. Oil scraper rings allow sufficient quantity of
lubricating oil to move up during the upward stroke and at the same time, scrap the
excess oil from the inner surface of the liner and send it back to the crankcase. This
prevents the leakage of oil into the combustion chamber.
(i) Materials of Piston Rings Piston rings are usually made of grey cast iron and in
some cases, alloy cast iron. Grey cast iron has excellent wear resistance. It also
retains the spring characteristic at high temperatures. In some cases, piston rings
are chromium plated to reduce wear.
(ii) Number of Piston Rings: There are no strict rules for deciding the number of
compression rings. The number of compression rings in automobile and aircraft
engines is usually between 3 to 4. In stationary diesel engines, 5 to 7 compression
rings are used. The number of oil scraper rings is usually between 1 to 3.
b=D√ (10)
where,
b = radial width of ring (mm)
Note
(i) The radial wall pressure is usually taken from 0.025 to 0.042 MPa.
(ii) The permissible tensile stress for cast iron rings is taken from 85 to 110
(N/ ).
h = (0.7b) to b (11)
where h is the axial thickness of the piston ring in mm. There is a limit on the
minimum axial thickness. It is given by,
( )
z = number of rings
It is preferred to provide more number of thin piston rings than a small number of
thick rings. It has the following advantages:
(a) Thin rings reduce frictional loss and wear of the surface.
(b) More number of thin rings has better sealing action than a few thick rings.
(d) More number of thin rings provides better heat transfer from the piston top to
the cylinder.
(iv) Gap between Free Ends The diameter of a piston ring is slightly more than the
cylinder bore (D). A part of the ring is slightly cut diagonally as shown in Fig.
3(b). During the assembly, the ring is compressed diagonally and passed into the
liner. The gap G between the free ends of the ring is as follows:
(v) Width of Top Land and Ring Lands: Refer to Fig. 4 for top land and ring
lands.
=( ) to (1.2 ) (13)
The distance between two consecutive ring grooves ( ) is called the width of the
ring groove and is given by,
= 0.75 h to h (14)
PISTON BARREL
The piston barrel is shown in Fig. 5. It is the cylindrical portion of the piston below
the piston head. The thickness of the piston barrel at the top end is given by,
where,
The thickness of piston barrel at the lower or open end is given by,
PISTON SKIRT
As shown in Fig. 1, the cylindrical portion of the piston between the last scrapper
ring and the open end is called the piston skirt. The piston skirt acts as a bearing
surface for the side thrust. The length of the skirt should be such that the bearing
pressure due to side thrust is restricted to 0.25 MPa on the projected area. In high
speed engines, the bearing pressure up to 0.5 MPa is allowed to reduce the weight
of the reciprocating piston. The maximum side thrust will occur during expansion
stroke.
where is the coefficient of friction ( = 0.1) The side thrust taken by the skirt is
also given by,
where,
( ) = D
( ) = D (17)
L = D to 1.5D (20)
PISTON PIN
The function of the piston pin is to connect the piston to the connecting rod. It is
also called ‘gudgeon’ pin or ‘wrist’ pin. It is made of hollow circular cross section
to reduce its weight. It is often tapered on the inside and the smallest diameter is at
the centre of the pin. The piston pin passes through the bosses provided on the
inner side of the piston skirt and a bearing bush inside the small end of the
connecting rod as shown in Fig. 6(a). The end movement of the piston pin is
restricted by means of circlips.
The piston pin is made of carbon steel or alloy steel. It is hardened and ground to
reduce wear while turning inside the phosphor bronze bush. There are two criteria
for design of the piston pin-bearing consideration and bending failure.
(i) Bearing Consideration: The piston pin is partly in contact with piston bosses
and partly with the bush of the connecting rod as shown in Fig. 6(a). The bearing
area of the piston pin is approximately divided between the piston bosses and the
connecting rod bush. It is assumed that the length of the pin in the connecting rod
bush is 45% of the piston diameter (D) or cylinder bore. Therefore,
= 0.45D (21)
where,
= length of piston pin in the bush of the small end of the connecting rod (mm)
The outer diameter of the piston pin ( ) is determined by equating the force
acting on the piston and the resisting bearing force offered by the piston pin:
where,
Note
(i) The bearing pressure at the bushing of the small end of the connecting rod ( )
is taken as 25 MPa.
(ii) The inner diameter of the piston pin is taken as 0.6 times of the outer diameter.
= 0.6 (23)
Mean diameter of piston bosses = 1.4 (for grey cast iron piston)
(ii) Bending Consideration: Refer to Fig. 6(b). The bending moment acting on the
pin at the central section XX is given by,
( )x( ) ( )x( )
Also,
=( ) (b)
Substituting (b) in (a),
( ) x ( )( ) ( )x( )
=( )+( )-( )
( ) (24)
Also,
( )
I= (25)
y= ( )
and =
Using the above relationships, the maximum bending stress in the piston pin at the
central plane is calculated.
Note: The allowable bending stress for the piston pin should not exceed the
following values:
(iii) Piston Clearances: The clearance between the cylinder liner and piston is
provided to take care of thermal expansion and distortion under load. When the
clearance is insufficient, ‘piston seizure’ occurs. On the other hand, when
clearance is excessive, ‘piston slap’ occurs resulting in piston running with
excessive noise. The magnitude of piston clearance varies from 0.0375 to 0.1875
mm depending upon the piston diameter and the type of engine. In aluminum alloy
piston, the clearance is twice that of cast iron piston. The clearance is less when
proper cooling system is provided resulting in smaller thermal expansion.