Professional Documents
Culture Documents
Operation Instruction
the directions.
by our company.
can be put in or taken out easily. The refrigeration effect is good and the
Users can regulate and check the inside temperature and the working
The system is equipped with a safety protection device for ensuring the
The refrigerating system all adopts imported parts which provide good
II Precautions
The sign of “ ” means the place is dangerous to human bodies, or
the use pattern is harmful to products, or alarm users should pay special
attention to this.
transportation.
: The slant angle of the body of the ultra low temperature freezer
:If the ultra low temperature freezer has to be stopped for a long
period, it should be cleaned inside and outside and then covered properly
equip a power regulator which is above 1000VA and please use it alone.
independent ground wire. The ground wire cannot be connected with gas
pipe, stem heating pipe and water pipe and the zero line of single-phase
:If the power connect wire has to be lengthened, the sectional area
:The ultra low temperature freezer cannot lean against the wall. The
space of at least 30cm should be left at the machine room for normal
prohibited to use the product in the rain or under the environment with the
machine halt to prevent the compressor or the system from being damaged.
:The key of the ultra low temperature freezer should be kept out of
and alkali etc. with strong corrosiveness are never allowed to be put in the
4
research etc. for low-temperature freezing, storage, test and subzero
treatment.
side of the temperature controller on the front part of the body). Then the
power supply indicator light is on. In order to ensure the normal running of
the cryogenic freezer, be sure to use the socket which is above 16A.
refrigeration indicator light is on. The system goes into refrigerating cycle
state.
·After the power has been supplied for a period of time, the
5
·Before storing articles, please keep the freezer running in empty state.
When the freezer is running stably (it is best to keep it running in empty
state for 5 hours above) and the inside is cooled completely, the cold store
Model BDF-40H300
Type Horizontal
Total effective volume (L) 300
Storage temperature -15℃~-40℃
Rated voltage (v) 220
Frequency (Hz) 50Hz
Rated power(W) 720
Electric-shock protection class Class I Type B
Type of alarm Sound-light alarm
Climate type N
Refrigerating fluid Fluoride-free mix
Net weight of machine (Kg)/ Gross weight(Kg) 140/165
Machine dimensions width×depth×height (mm) 153 0*7 50 *860
Notes: technical parameters in this table are measured at the standard state.
Please be subject to the nameplate of the goods freezer without prior notice in case
of variation.
6
2. Description
The KLT11-D is designed for heating and cooling applications. The probe
temperature is displayed on the bright 3-digit display . The user is able to program
different parameters including set point, hysteresis, alarms and probe adjustment using
the silicone front keypad. The unit features error or alarm warning, internal buzzer
(optional), configurable digital input and password protection. The KLKey input
allows an easy programming of the parameters. Select between temperature display in º
C or ºF , display color and 230V ac, 115V ac, 24V ac/dc or 12V ac/dc power supplies.
3. Mai nt en a nc e, cl e a ni n g an d rep a i r
Aft er fi nal in s t al l at i on of the uni t , no rout i ne ma in ma int e n ance is
requ i re d.
Cl ea n th e su rf ace of the di s pl ay con t rol l er wit h a sof t and da m p
cl o th . Ne ver us e ab ras i ve det e rgent s , pe t rol , alc oh ol or sol vent s .
All re pai rs mu s t be ma d e by aut hori ze d pe rs on nel .
4. List of parameters
7
Des cr ip ti on Uni ts Range Fa ctor y
SP Set Po i n t Degre es r1 to r2 -60
r0 Dif fer en t i al or Degre es 0.1 to 99.9 5
hy s t e res i s
r1 Lower va lu e for SP Degre es -200 to r2 -50
r2 Hig he r va l u e for SP Degre es r1 to 600 200
r4 Set Po i n t va ri at i on Degre es 0.1 to 200 3.0
d0 Co ol i n g or he at i n g Degre es Co/ Ht Co
co nt rol
c0 Mi ni m um st op pi ng ti m e Sec onds 0 to 999 0
c2 Ou tput st a tus wi t h Opti o n On/O FF ON
pr ob e error
P1 Ambi e n t pr obe Degre es -99. 9 to 0.0
ad j u s tm en t 99.9
P4 Deci m al po i nt Opti o n no/ ye s ye s
P5 3 wir es Pt 10 0 Opti o n no/ ye s ye s
E0 Dig i t al inp ut Opti o n OFF / Al /E S/ OFF
co nfi gu ra ti on HC
H5 Acce s s co de to Nume ri c 0 to 255 0
pa ram e te rs
A0 Ala rm 1 hy s t e res i s Degre es 0.1 to 99.9 1.0
A1 Ala rm 1 th r es h ol d Degre es 0.0 to 999 0.0
A2 Ala rm 1 ex cl u s i on ti m e Sec onds 0 to 999 0
A3 Ala rm 1 ty pe Opti o n OFF / HI/ LO OFF
A4 Ala rm 2 hy s t e res i s Degre es 0.1 to 99.9 1.0
A5 Ala rm 2 th r es h ol d Degre es 0.0 to 999 0.0
A6 Ala rm 2 ex cl u s i on ti m e Sec onds 0 to 999 0
A7 Ala rm 2 ty pe Opti o n OFF / HI/ LO OFF
A8 Ala rm ve ri fi ca t ion ti m e Sec onds 0 to 999 0
5. Parameter descriptions
SP = Set poi n t . Tem p era t u re we wis h to re g ul at e the mac hi ne
(v ari a b le from r1 to r2 )
r0 = Di ff ere nt ia l or hys t ere s i s
R1 = Lower va lue for SP
r2 = Hi g her va l u e for SP
r4 = Set po i nt va ri at i on fo r ener gy sa vi ng. If di gi t al inp ut
co n fi gura ti o n E0 ES th i s va l ue mod i fy the se t poi nt as fol low s:
If d0= Ht ne w SP= SP - r4
If d0= Co ne w SP = SP + r4
do = Cool i ng or he at i ng co nt rol
If d0 = Ht an d TS is th e te mpe ra tur e of am b ie nt pr obe:
8
If TS >= SP th e loa d is di s c onnect e d
If TS <= SP - r0 the loa d is con nect e d
If d0 = Co th en :
If TS <= SP the loa d is di s c o nnect e d
If TS >= SP + r0 the loa d is con nec te d
c0 = Mi ni mum st op pi ng ti m e of the loa d
c2 = Ou t p ut st a tus wit h pr obe error
P1 = Ambi e n t pr ob e ad j u s tm e n t
P4 = Deci m al poi n t
P5 = 3 wir es Pt 10 0. no = 2 wir es , yes = 3 wir es
E0 = Dig i t al in pu t co nfi gura ti on
OFF = Digi t al in pu t di s ab l e d
Al = Exte rn al al arm (i f in put is shor t- ci rc uit e d)
ES = Energy Savi ng . Set Poi nt va l ue is mod i fi e d in r4.
HC = if in pu t is sh ort - ci rcui t ed , it change s to Heat or Col d
de p end i n g of d0 va lu e .
if d0 = Heat it chang es to Col d mod e .
if d0 = Co l d it chang es to Heat mod e .
6. Parameter programming
Set Poi nt (SP ) is th e onl y pa ra me t er the us e r can
acc es s wit hou t co de pr ote ct i on.
• Pre s s SET . SP te xt wil l app e ar on the di s pl ay .
• Pre s s SET ag ai n . Th e rea l val u e is show n on the di s pl ay.
• Th e val ue can be mo di fi e d wit h the UP and DOWN arrow s .
• Pre s s SET to en t er an y ne w va lue s .
• Pre s s SET an d DOWN at the sa m e ti m e to qui t
9
pr o g ram m i ng or wa i t on e mi n ut e and the di s pl ay wil l
au t o ma t ic al l y ex i t pr og ram m i ng mod e .
9. Alarm validation
In cas e of al arm th e in t er nal buz zer and ala rm le d is act i vat ed . Th e
di s pl ay sh own th e co rre s po ndi ng me s sa ge. Th e buz ze r and di s pl ay
me s sa ge can be si l en c ed pr es s i ng the SET and DO WN arrow s at th e
sa m e ti me . If ala rm co nt in ue s af t er A8 it is si gna ll i ng agai n.
10
VIII Schematic circuit diagram
IX Storage essentials
·Before storing articles, please keep the freezer running in empty state.
When the freezer is running stably (it is best to keep it running in empty
state for 5 hours above) and the inside is cooled completely, the cold store
too much. Proper clearance should be left to help the circulation of the
device used for maintaining low temperature rather than a quick freezing
precool them in other quick-freezing plant and then store them in the
temperature is reached.
·When storing plastic bag products, please note that do not get them
X Maintenance
·Body cleaning: please use non-corrosive neutral cleaning agent to clean
the inside and outside surfaces of the ultra low temperature freezer and then
and outside surfaces of the freezer so as not to affect the insulating property
cleaning.
·Regularly wipe a little talcum powder on the door seal to extend the
·If the ultra low temperature freezer has been running for a long time,
frost may be easily accumulated on the door seal, the opening part of the
freezer and the side wall inside the freezer. If the frost layer is too thick, the
12
·Please use non-corrosive neutral cleaning agent to clean the inside
and outside surfaces of the freezer and then use dry cloth to wipe it up.
·Machine halt: when stop using the freezer, unplug the power plug, clean
it according to the above method, cover it with a plastic bag after natural
XI Non-fault phenomenon
·Sound of running water can be heard in the ultra low temperature
·You may feel a little hot on the two sides of the body (close to the
door body) when the freezer is running. That is because the leak proof tube
condensation on the outer surface of the freezer and the door seal. Then rub
dry.
·If the power plug wire is properly connected and the main power
13
supply is plugged in
·The door is opened too often for too long: try to reduce the
door-opening time
·The storage capacity is too much: take some out or distribute evenly to
·The condenser is dirty and the heat dissipation is not good: clean the
3.Large noise
·If the back part of the freezer body contacts with the wall: please
·The fan in the machine room makes a lot of noise: the fan is broken
Notes: if the ultra low temperature freezer still cannot work normally
after being inspected and handled according to the above methods, please
company’s products and maintain the legal rights of the consumers, our
Bureau of Finance and provide you with following services basing on the
The whole machine is guaranteed for twelve months since the purchase
The whole machine can enjoy life service. And we will charge for
caused by the fact that the user does not operate according to the
invoice
Packing Accessories
1 1 2
16
To distributor:
The warranty card should be full filled by distributor, only effective with seal and filed by
sales department.
Product name:
Product model:
Final user (or unit) name: Guarantee period:
Final user (or unit) address: Phone No.:
Purchase date:
Distributing unit name: (effective with seal)
Phone No.: Address:
After filling it, please cut it off along the dash line.
Product name:
Product model:
Final user (or unit) name: Guarantee period:
Final user (or unit) address: Phone No.:
Purchase date:
Distributing unit name: (effective with seal)
Phone No.: Address:
Company:
Biobase Biodustry (Shandong) Co., Ltd.
Address:
No. 51 South Gongye Road, Jinan, Shandong, China