Professional Documents
Culture Documents
KOD KURSUS
COURSE CODE
: BEEC1303
KURSUS : ELEKTRONIK ASAS
COURSE : BASIC ELECTRONICS
PENYELARAS
COORDINATOR
: NURLIYANA BINTI ABD MUTALIB
PROGRAM
PROGRAMME
: 1 BEEC
MASA : 9.00 PAGI – 11.00 PAGI
TIME : 9.00 A.M – 11.00 A.M
TEMPOH : 2 JAM
DURATION : 2 HOURS
TARIKH : 4 FEBRUARI 2021
DATE : 4th FEBRUARY 2021
TEMPAT : HALL 7
VENUE : HALL 7
1. Jawab SEMUA soalan-soalan pada bahagian A dan jawab SATU (1) soalan
sahaja daripada DUA (2) soalan pada bahagian B.
Answer ALL questions on part A and answer ONE (1) question only out of TWO (2)
questions on part B.
2. Tuliskan semua jawapan anda di atas kertas jawapan yang disediakan.
Write your answer on the answer sheet provided.
3. Setiap jawapan kepada soalan hendaklah dimulakan di muka surat yang baru.
All answers to the questions should be written in a new page.
SULIT
(BEEC 1303) SULIT
BAHAGIAN A
SOALAN 1
(i) Penebat
[2 markah]
(ii) Konduktor
[2 markah]
(iii) Semikonduktor
[2 markah]
(e) Lukiskan dan labelkan jalur tenaga bagi getah, kuprum dan silikon.
[6 markah]
(f) Hukum ohm adalah hukum yang paling asas dalam litar elektronik.
-2- SULIT
(BEEC 1303) SULIT
[25 MARKAH]
-3- SULIT
(BEEC 1303) SULIT
SOALAN 2
RL
120VAC 1000Ω
10:1
(d) Namakan litar yang digunakan untuk menghilangkan sebahagian daripada isyarat
masukan tanpa herotan isyarat seperti dalam Rajah S2 (d).
Vi
t Vi Vo
[1 markah]
(e) Kirakan isyarat voltan keluaran, vo, berdasarkan Rajah S2(d), diberikan diod yang
digunakan adalah diod silikon
[3 markah]
-4- SULIT
(BEEC 1303) SULIT
(f) Bandingkan DUA (2) perbezaan diantara pincang hadapan dan pincang balikan diod.
[4 markah]
(g) Jelaskan DUA (2) perbezaan diantara penerus separuh dan penerus penuh.
[4 markah]
[25 MARKAH]
-5- SULIT
(BEEC 1303) SULIT
BAHAGIAN B
SOALAN 3
(a) Berdasarkan Rajah S3(a) dan Jadual S3(a). Kenal pasti pin terminal dan jenis transistor
tersebut.
1 2 3
[4 markah]
(b) Daripada pemahaman anda, bincangkan mod operasi BJT.
[3 markah]
-6- SULIT
(BEEC 1303) SULIT
(c) Tentukan IB, IC, IE, VBE, VCE, dan VCB dalam litar Rajah S3(c). Transistor tersebut
mempunyai βDC = 150.
[10 markah]
(e) Rajah S3(e) menunjukkan litar penguat. Analisis sifat penguat dari segi jenis dan
gandaan.
Vin
Vin +
Vout
Vout
– Rf
82 kW
Ri
3.3 kW
[25 MARKAH]
-7- SULIT
(BEEC 1303) SULIT
SOALAN 4
(b) Huraikan TIGA (3) perbezaan sifat operasi diantara transistor dwikutub dan
transistor kesan medan.
[6 markah]
(c) Rajah S4(c) menunjukkan JFET yang mempunyai VGS(off) = -4 V dan IDSS = 12 mA.
Kirakan nilai minimum VDD yang diperlukan untuk meletakkan peranti di rantau arus
malar pengoperasiannya apabila VGS = 0 V.
[9 markah]
RD
330Ω
Rajah S4(c)
-8- SULIT
(BEEC 1303) SULIT
(e) Rajah S4(e) menunjukkan litar penguat. Analisis sifat penguat dari segi jenis dan
gandaan.
82kΩ
3.3kΩ Vout
Vin
[25 MARKAH]
- SOALAN TAMAT -
-9- SULIT
(BEEC 1303) SULIT
PART A
QUESTION 1
(i) Insulator
[2 marks]
(ii) Conductor
[2 marks]
(iii) Semiconductor
[2 marks]
(e) Draw and label the band gap of rubber, copper and silicone.
[6 marks]
(ii) Explain the Kirchoff Voltage Law (KVL) using appropriate circuit and write
the voltage equation based on your circuit.
[3 marks]
-10- SULIT
(BEEC 1303) SULIT
(iii) Two resistor R1 and R2 are connected in parallel with the 20V DC supply. R1
taken 2A current from supply. If total resistance for both resistor is 4.5Ω,
determine the resistance for R2.
[3 marks]
(iv) By referring to Q1f(iii) calculate the total power for the circuit
[2 marks]
[25 MARKS]
-11- SULIT
(BEEC 1303) SULIT
QUESTION 2
(c) Explain the conditions that allow current to flow through a load resistor (RL) in the Figure
Q2(c) circuit.
RL
120VAC 1000Ω
10:1
(d) Name the circuit used to eliminate a portion of an input signal without distorting the
signal as shown in Figure Q2(d).
Vi
t Vi Vo
(e) Calculate the output signal, vo, based on Figure Q2(d). Given the diode is silicone.
[3 marks]
(f) Compare TWO (2) differences between forward bias and reverse bias of a diode.
[4 marks]
-12- SULIT
(BEEC 1303) SULIT
(g) Explain TWO (2) differences between a half-wave rectifier and a full-wave rectifier.
[4 marks]
(h) The DC power supply converts the standard 230 V, 60 Hz AC voltage from the wall
outlets into a constant dc voltage. Draw a basic block diagram of a complete AC to DC
power supply with the output waveform at each block.
[10 marks]
[25 MARKS]
-13- SULIT
(BEEC 1303) SULIT
SECTION B
QUESTION 3
(a) Based on Figure Q3(a) and Table Q3(a), identify the terminal pins and the type of the
transistor
1 2 3
[4 marks]
-14- SULIT
(BEEC 1303) SULIT
(c) Determine IB, IC, IE, VBE, VCE, and VCB in the circuit of Figure Q3(c). The transistor has a
βDC = 150.
[10 marks]
(e) Figure Q3(e) shows the op-amp circuit. Analyze the characteristics of the op-amp
in term of type and gain.
Vin
Vin +
Vout
Vout
– Rf
82 kW
Ri
3.3 kW
[25 MARKS]
-15- SULIT
(BEEC 1303) SULIT
QUESTION 4
(b) Describe THREE (3) differences between the operating properties of bipolar transistors
and field effect transistors.
[6 marks]
(c) Figure Q4(c) shows JFET with VGS(off) = -4 V and IDSS = 12 mA. Determine the
minimum value of VDD required to put the device in the constant-current region of
operation when VGS = 0 V.
[9 marks]
RD
330Ω
-16- SULIT
(BEEC 1303) SULIT
(e) Figure Q4(e) shows the op-amp circuit. Analyze the characteristics of the op-amp in
term of type and gain.
82kΩ
3.3kΩ Vout
Vin
[25 MARKS]
- END OF QUESTIONS –
-17- SULIT