Professional Documents
Culture Documents
4.25 inches
Multi-Gender Board Jig
p/n: RAD33187801 (Sold Separately ($22.30))
3.35 inches
s
1.10 inches
Multi-Gender Board
to Smart Test Jig
Cable Included
Multi-Gender Board
p/n: RAD33187801
($43.60)
1. New
1 N 18Pi
18Pin
Smart JIG 2015/2016 24Pin
2015 2015
(LF/UF Series) (OLED)
Zip tied o
on 3 plug cables
24Pin
28Pin
2013/2014
2. Old
Smart JIG 2017
(OLED)
24Pin Use this
24Pin
2012 port for B7
/ G7 24pin
SJ95/UJ98 (Use P18 plug) (79SJ95 Use P15 plug) Note 2: VIDEO TEST (Panel Diagnostics):
SJ85/UJ94 (Use P13 plug) See page 22. (Also available Article 9268).
SJ80, UJ77 (Use P13 plug) (See note 2 on right) “OLED Panel Diagnostics Guide.”
UJ75/UJ78 (Use P13 plug) Note: You will use this document to turn on the
2017 LED
UJ65/UJ68 (Use
(U P13 plug)
l ) P
Power Supply
S l which
hi h iin tturn provides
id power to
t the
th
UJ63/UJ67 (Use P13 plug) (49UJ63 Use P17 plug) Smart Power Test Jig and T-CON Board.
LJ61/LJ68 (Use P13 plug) EG91,2,3,4: See Page 14
LJ55/LJ58 (Use P13 plug) LCD “UJ77” Jump 12V to T-CON. (Pg 29).
Page 5 of 29
How to Connect the Multi Gender Board to the Smart Power Test Jig
▶ Plug cable into the Multi Gender Board: Into port (MAIN Jig In)
3 4
1 2
▶ Check
Ch k power board
b d voltage,
l (13
(13.2V).
2V) ▶ Disconnect the Main Board 18Pin Power Cable connector.
3 4
3 4
3 4
▶ Connect the 28Pin Power Cable connector ▶ Apply Power; when the OK LED turns on,
to the Multi Gender
G JIG
G 28Pin P15 connector. Power Board is normal.
normal Backlights should be On
On.
▶ Set the PRODUCT SWITCH on SMART JIG to LCD. ▶ Check all voltages out to the Main board.
▶ LCD MODEL SWITCH: Set the switch to 24V. ▶ When the NG LED turns on, the Power Board
can be judged as defective.
Page 9 of 29
2016 / 2017 LED 12Pin Power Board Diagnostic Method
1 2
3 4
1 2
3 4
Also
49UJ63**
1 2
▶ Check
Ch k power board
b d voltage
lt (13.2V
(13 2V and
d 20V)
20V). ▶ Disconnect
Di t the
th Main
M i Board
B d 28Pin
28Pi P
Power C
Cable
bl connector.
t
3 4
1 2
3 4
▶ Disconnect the Main Board 24Pin Power Cable connector. ▶ Connect the 24Pin Power Cable connector to the Multi
Gender JIG 24Pin connector (P8 Port).
Page 13 of 29
2015 OLED (EG91, 92, 93, 94, EG96, EF95) Power Board Diagnostic Method (2 of 2)
5 6 Green
Be sure to check all voltages from the Power Supply to the Main Board and to the T-CON Board.
7 MAIN VOLTAGES: T-CON
T CON VOLTAGES:
• 3.5V, (P201 pins 5, 7, 8) • 12VT, (P203 pins 7-12)
• 12VM, (P201 pins 11-15) • 24VD, (P202 pins 8-14)
• 24VS, (P201 pins 19-22)
NOTE: EG91 SERIES: Only necessary if you want to run the Panel Diagnostic Test. (Also see Article 9268 for details)
In the EG91 Series OLED, the 12VT for the T-CON is routed out of the Main board through the LVDS Cable. 12VT is routed from the
Power Supply to the Main Board and to the T-CON Board. To run the OLED Video Panel Test (rolling test patterns) it will require an
additional step. You will have to Jump 12V from the Power Supply to the T-CON Fuse.
Page 14 of 29
2016 OLED (C6, E6, G6, B6) Power Board Diagnostic Method (1 of 2)
1 2
3 4
▶ For C6, E6, and G6, Connect the 24Pin Power Cable
connector to the Multi-Gender JIG 24Pin connector (P10 Port).
▶ Disconnect the Main Board 24Pin Power Cable connector. ▶ For B6, Connect the 24Pin Power Cable connector to the Multi
Gender JIG 24Pin connector (P7 Port).
Page 15 of 29
2016 OLED (C6, E6, G6) Power Board Diagnostic Method (2 of 2)
5 6 Green
7 For C6, E6, and G6, Check all voltages from the Power Supply For B6 model, check this Power Supply to the Main
to the Main Board and to the T-CON Board. Board and to the T-CON Board.
• MAIN VOLTAGES: • MAIN VOLTAGES:
• 3.5V_ST, (P201 pins 5, 7, 8) • 12VM, (P201 pins 5,7,8 and 13-15)
• 12VM, (P201 pins 11-15) • 24VS, (P201 pins 19-22)
• 24VS,
24VS (P201 pins 19-22)
19 22) • T-CON
T CON VOLTAGES:
• T-CON VOLTAGES: • 12VT, (P203 pins 7-12)
• 12VT, (P202 pins 7-12) • 24VD, (P202 pins 8-15)
• 24VD, (P203 pins 8-15)
Page 16 of 29
2017 OLED (C7, E7) Power Board Diagnostic Method (1 of 1)
1 2
3 Green
4
1 2
3 4
ATTENTION:
For the 24Pin
Connector type,
Do not use P11.
Use the 24Pin
connector P13
P13.
(Labeled W7)
▶ Unplug the 24Pin Power Cable connector ▶ Connect the 24Pin Power Cable connector
from the Main board. to the Multi Gender JIG 24Pin connector P13.
Page 18 of 29
2017 OLED (B7, G7) Power Board Diagnostic Method (2 of 2)
5 SPECIAL STEP FOR THE B7, G7. Unplugged Side of Main Board P1001
20VS 23 24 20VS
NOTE: These pin 20VS 21 22 20VS
numbers are Main
Gnd 19 20 Gnd
Board plug side.
12VM 17 18 12VM
15 16
8th pin up from
Gnd
12V_ON b tt
bottom right.
i ht
Gnd 13 14 Gnd
6th pin up from 11 12
Add Jumper PWR_ON
ACD
bottom left
Gnd 9 10 12VM
▶Add a jumper wire (Needle tip on each end) 7 8
12VM 12VM
between Pins 11 and 16 P1001 sideside, (13 and 10
5 6
P201 side). This will give the command to the 20VS 20VS
Power Supply to turn on the 12VT to the T-CON. Add Jumper Gnd 3 4 Gnd
DRV_ON 1 2 DPC
1 2
3 4
Page 20 of 29
2017 OLED (W7) Power Board Diagnostic Method (2 of 2)
5 SPECIAL STEP FOR THE B7, G7. Unplugged side of Main Board P1001
No Wire 23 24 20VS
▶ Apply
pp y Power,, when the OK LED turns on,, Power WARNING: To use the Smart Jig & Multi-Gender
Multi Gender board or run
Board is normal. OLED Panel Diagnostics on the W7 requires a Jumper between
PWR_ON and 12V_ON. If you feel uncomfortable or unable to
▶ When the NG LED turns on, the Power Board make and/or use a needle jumper, please do not attempt.
can be judged as defective.
Page 21 of 29
Use in conjunction with Smart TV Power Test “Previous”: Also Articles 9267 and 9268.
※ For the EG9100 and UJ77 Series models you will need
an alligator clip jumper wire instead of this needle tipped
jumper. Usage explained Page 29 (Also in Article 9267)
Multi-Gender Board
Cable Included
($5 60)
($5.60)
Multi-Gender Board OLED Panel Diagnostic Cable
($22.30)
p/n: RAD33187801 p/n: AGF79219801
Page 24 of 29
Power Board Multi Gender JIG Layout (P/N: RAD33187801)
2015 2015/2016
(LF/UF Series) (OLED)
※ 12/13/2014 Smart JIG
connector applied 28Pin 24Pin 24Pin 24Pin NC
2015 18Pi
18Pin
24Pin
2013/2014 24Pin
28Pin
2017
(OLED)
To the Smart
TV Test Jig 2016/2017
18Pin
“A” (UH/UJ)
▶ Plug cable into the Multi Gender Board: Into port (MAIN Jig In)
1 2
13.2V/18V 24V
Page 27 of 29
How to Connect the OLED Panel Diagnostics Cable Page 28 of 29
3 4 p/n: AGF79219801
“Module” Label:
This plugs into the
This plugs T-CON board.
into the Smart
Test Jig
▶ OLED Panel Diagnostic Cable notes.
▶ Hook the TV up using the normal Smart Power Supply
Test Jig and Multi-Gender Board. This will allow the TV to
be turned on and apply power to the Panel and T-CON
Board. DO NOT turn set on at this time. 6
N/G OK
5 “Module” Label
▶ See Article 9267 for complete details related to proper hook-up of NOTES:
the Multi-Gender board and the Smart Power Test Jig to your panel.
▶I
▶Important:
t t Disconnect
Di t “Both”
“B th” V
Vx1
1 (LVDS) cables.
bl
7 Smart Jig to
▶ It is necessary for the Power Supply to be producing the
Multi-Gender
12VT and the 20VD or 24VD to the T-CON.
OLED Diagnostic Vx1 Cables ▶ Note: Follow the specific steps for setting up your specific
Cable from Smart disconnected
Model TV to run correctly when connected to the Smart
Jig to T-CON
T CON
Jig and Multi-Gender Board.
Diagnostic Cable The Green “OK” LED on the front of the Smart Jig must be
plugged into
turned on, (Illuminated).
T-CON 51pin
▶ For Most Models, you do not need to add a jumper.
Additional Jumper But for some Models they will require the addition of a
required
q only
y on
“Jumper”
Jumper wire (as shown in the example on the left for a
some models.
B7 OLED model.
Multi-Gender The following OLED series models (B7, W7 and G7)
Board to turn on require a jumper wire to activate the 12V_ON command to
Power Supply the Power Supply so the 12VT and the 20VD or 24VD
voltages will turn on.
▶ Apply Power to the Set and observe the front of the OLED (All off these
th will
ill use th
the same 24pin
24 i connector
t on the
th
Panel. It should be producing Patterns on the screen. Multi-Gender board P13, (lower right). The Jumper jumps
▶ OLED Patterns may vary by panel design. Some will be PWR_ON to 12V_ON. (See previous section for details).
rolling test patterns of Black, White, Red, Green, Blue, then
repeats with a lower IRE level. The OLED “EG91, 2, 3, 4” series and LCD “UJ77”
Other ppanels have section sweep pppatterns that run Series models require jumping 12V from the Power
horizontally then vertically. Supply to the T-CON because this model receives 12VT
from the Main board through the LVDS cable. Use a small
▶ If the Panel fails to product patterns on the screen. Confirm the alligator clip lead type jumper for easier attachment.
12VT and 20VD or 24VD to the T-CON. Note: Before applying power, Diode check the Fuse on
Be sure the check these voltages on the T-CON board itself. the T-CON for a possible short.
There will be fuses for both voltages.
WARNING T
WARNING: To use th
the S
Smartt Ji
Jig & M
Multi-Gender
lti G d board
b d or run
If they are present see T-CON Troubleshooting to confirm if the OLED Panel Diagnostics on the G7, B7 or W7 requires a Jumper
problem is the T-CON board or the Panel that needs replacing. between PWR_ON and 12V_ON. If you feel uncomfortable or
unable to make and/or use a needle jumper, please do not attempt.
Page 29 of 29