Professional Documents
Culture Documents
R210LC-7 8-10
R210LC-7 8-10
1. TRACK LINK
1) REMOVAL
(1) Move track link until master pin is over
front idler in the position put wooden
Master pin
block as shown.
(2) Loosen tension of the track link.
※ If track tension is not relieved when the
grease valve is loosened, move the
machine backwards and forwards.
(3) Push out master pin by using a suitable
tool.
Block
8-161(1) 210-7
8-161(2) 210-7
2) INSTALL
(1) Carry out installation in the reverse order
to removal.
※ Adjust the tension of the track link. 90 ~ 110
21074OP14
8-151
2. CARRIER ROLLER Frame
1) REMOVAL
(1) Loosen tension of the track link. Grease
valve
8-162(1) 210-7
8-162(2) 210-7
8-162(3) 210-7
2) INSTALL
(1) Carry out installation in the reverse order
to removal.
8-152
3. TRACK ROLLER Frame
1) REMOVAL
(1) Loosen tension of the track link. Grease
valve
8-163(1) 210-7
90-110°
8-163(2) 210-7
8-163(3) 210-7
2) INSTALL
(1) Carry out installation in the reverse order
to removal.
8-153
4. IDLER AND RECOIL SPRING
1) REMOVAL
(1) Remove the track link.
For detail, see removal of track link.
8-164(1) 210-7
8-164(2) 210-7
2, 3
8-164(3) 210-7
2) INSTALL
(1) Carry out installation in the reverse order
to removal.
※ Make sure that the boss on the end face
of the recoil cylinder rod is in the hole of
the track frame.
8-164(4) 210-7
8-154
3) DISASSEMBLY AND ASSEMBLY OF IDLER
(1) Structure
6 5
8
3
1 2
4
4
3
5 21078DA43
8-155
(2) Disassembly Press
① Remove plug and drain oil.
② Draw out the spring pin(7), using a press.
7 8-166(1) 210-7
2
8-166(2) 210-7
4
8-166(3) 210-7
8-156
(3) Assembly
※ Before assembly, clean the parts.
※ Coat the sliding surfaces of all parts with 1 4 Press
oil.
① Cool up bushing(4) fully by some dry ice
and press it into shell(1).
Do not press it at the normal temperature,
or not knock in with a hammer even after
the cooling.
8-167(1) 210-7
8-167(2) 210-7
8-167(3) 210-7
8-167(4) 210-7
8-157
⑥ Install bracket(5) attached with seal(3).
8-168(1) 210-7
8-168(2) 210-7
8-168(3) 210-7
8-158
4) DISASSEMBLY AND ASSEMBLY OF RECOIL SPRING
(1) Structure
4 7, 8 3 6 5 2 1 9 10 11 12
13 R210UCG1
8-159
(2) Disassembly
① Apply pressure on spring(3) with a press.
※ The spring is under a large installed load.
This is dangerous, so be sure to set
properly.
・Spring set load : 13716kg(30238lb) 4
② Remove bolt(7), spring washer(8) and
7, 8
lock plate(6).
3
③ Remove lock nut(5).
6
Take enough notice so that the press 5
which pushes down the spring, should
not be slipped out in its operation.
④ Lighten the press load slowly and
remove bracket(4) and spring(3).
R210UCG02(1)
13
R210UCG02(2)
R210UCG02(3)
8-160
(3) Assembly
① Install dust seal(11), back up ring(10) and 1 9 10 11
rod seal(9) to body(1).
※ When installing dust seal(11) and rod
seal(9), take full care so as not to
damage the lip.
R210UCG02(3)
R210UCG02(5)
8-161
⑥ Lighten the press load and confirm the Press
set length of spring(3).
⑦ After the setting of spring(3), install lock
plate(6), spring washer(8) and bolt(7).
7, 8
3
6
5
431±1.5
R210UCG02(6)
8-162