Professional Documents
Culture Documents
>>
>>
manual and fully understand its contents. If any probroms, Main output RELAY:normal open AC 250V/5A DC 30V/5A COS¢=1
C: Press key and key to modify the numerals
please contact our sales or distributors whom you buy from. D: Press SET key to confirm
This manual is subject to change without prior notice.
① → PV ℃
SSR/LOGIC:24V DC ± 2V/ 20mA
↑
③ ⑦ T -150~400℃ (customized only)
trical shock, fire or malfunction may result.
Input S 0~1600℃ ↓ 3S
Do not wire when the power is on. Do not turn on the E 0~1000℃ Displays temperature unit
→ SET
>>
④ /AT
>>
>>
power supply when cleaning this instrument. Do not Rt Pt100 -199~600℃ Input type
disassemble, repair or modify the instrument. This may
↑ ↑ TA
Cu50 -50~150℃
Others Please mention when ordering ↓ 3S
cause electrical shock, fire or malfunction.Use this instru- Withstand voltage strength 1500V Rms (Between power terminal and the housing) Input UP limit
⑤ ⑥
ment in the scope of its specifications. Otherwise fire or ①. PV / parameter symbols Insulation resistance Min 50M Ω(500VDC)(Between power terminal and the housing) Input LOW limit
Environment temperature 0~50℃
malfunction may result. The internal relay’s service life is ②. SV / parameters set value Storage temperature -10~60℃ ↓ 3S
greatly dependent on the current and voltage switched by ③. Indication lamps Environment humidity 35~85%RH Measured displaying(PV)
↓
Weight ≤ 350g
its contacts. Over-stressing the contacts with too much OUT1: Heating/Main control output lamp Set displaying(SV)
current or switching vltage above the contact rating will On: Output Off: No output
↓ /AT
greatly shorten the life of the relay. OUT2: Alam2 output lamp Mounting and Sizes A Confirm
↑ ↑
>>
>>
Caution On: Output Off: No output Modify SV preset value
↑
This instrument is not rated foroutdoor use and should be used in
a climate controlled environment.
AT: On: Autotune Off: Non-autotune
AL: Alarm 1 lamp On: Alarm Off: No Alarm ↑ + + B SET
Shift and flashes
Installing in an environment heavy laden with dust or contain- ④.Set key Parameter Setting/Changing D Stop flashing
ing corrosive gasses will cause your controller to fail.
Do not install near water spray, oil spray, or in an environ-
⑤.Shift/Autotune key
Press this key to shift digit of parameter value setting. + +
↑
ment where water can condense inside the unit. Or hold this key for more than 3s can enter/quit autotune
C
>>
>>
In Non-autotune estate, press and hold / key for more
Avoid running power leads in parallel with high voltage or estate. When enter autotune estate, AT lamp on. When ↑ than 5 seconds can enter/quit the under menu: (Normally
heavy current carrying conductors that may induce high
quit autotune estate, AT lamp off. F the program will refresh the value of the parameters
voltages into the unit. If you must run incoming power by itself, the user no need make modifications. )
near high voltage or heavy current carrying conductors, we ⑥.Up key ⑦.Down key
↑
↓
↑
G
↑
suggest that you run the power inside metal conduit that is Models E H Low display value, it is adjust-
grounded on one end only. TA □□ - □□□□ Input signals:Default: K,J,E, S,PT100,Cu50 able by the input signal.
If installing in an electrically noisy environment, we sug- 1:4-20mA/0-10V/0-75mV F: others
SET eg. K type 0-800C, LSP=0.0
gest that you protect the unit with a current suppressor or
OUT2/AL2:R: RELAY S: SSR/Logic
Sizes
Model A B C D E F G H
↓ Up display value, it is adjustable
T: SCR N: None
noise filter. AL1:R:RELAY S:SSR/Logic T:SCR TA4 44.5+0.5 45+0.5 65 65 48 48 8 80 by the input signal.
Applications OUT1: I: 4-20mA V:0-10V DC TA6 43.5+0.5 91+0.5 65 115 48 96 12 80 eg. K type 0-800C, USP=100.0
TA series of temperature controller is available for many TC R: RELAY S: SSR/Logic TA7 67.5+0.5 67.5+0.5 115 115 72 72 12 80
↓ SET
Power supply: Default:90-260V AC/DC AL1 hysteresis setting value.
or RTD input, adopt some advanced techonology such multi E: 24VDC or 18-30V AC/DC TA8 91+0.5 43.5+0.5 65 115 96 48 12 80
Range ± 90, factory setting 1.0
digital filter circuit, autotune PID, fuzzy PID that make it Sizes 4: 48H × 48W 6: 48H × 96W TA9
↓ SET
91+0.5 91+0.5 95 95 96 96 12 80
is very precise, stable, strong anti-interference and 7: 72H × 72W 8: 96H × 48W 9: 96H × 96W
TA series of temperature controller
simple operation. The instrument is widely applied to
1
SET
1 Application examples
AL2 hysteresis setting value. Low analog output (when available) 10 A
90-260V AC/DC -
Range ± 90, factory setting 1.0 eg. 10-100℃ for 4-20mA output, trL=10
2 11 1.Relay output control (for TA7)
↓ SET ↓ SET
+
3 AL1 3
TC
12 B
RTD
High analog output(when available)
+
Decimal point setting: SSR
1
←
eg. 10-100℃ for 4-20mA output, trH=100 - 4 Relay 4 13
B 10
0: INT display 1: One decimal point 90-260V AC
OUT2/AL2
↓
← 2
↓SET SET
+ 5 14 Pt 11
Only function for 4-20mA/0-10V 7
Password setting. means PID control; SSR 6 15 3 12
RTD
8
- COM
13
90-260V AC/DC
4
4-20mA
Factory setting 015 means 4-20mA/0-10V analog output 7 16 AL1
------------------------------------------ ↓ SET
T1
▲
7 OUT1
Relay
NO
8 17 1 13 5 14
Temperature unit. C: ℃ degree,
↓HOLD SET >3 S T2 9 NC
6 15
F: F degree. G 9 18 2 14
OUT1
AL1 set range: –1999-9999
↓ SET
3 15 7 16
AL1 mode: TA7 AL1
↓SET 0: Deviation HI alarm 1: Deviation LO alarm
Parameter lock code setting. LcK=000
4 16 8 NO
17
means unlocked. LcK=010 means locked. R
2: PV HI alarm 3: PV LO alarm
Note:
5 17 J 9 NC
18
4: SV-PV > AL1 alarm 5: SV-PV <AL1 alarm Please operate according to the process in this instruc C
+ COM
6 FUSE
Heating cord
SET 6: TC broken alarm, 7:The first Low won’t alarm tion manual. Press <</AT key2s to enter auto-tune mode, T1 18 J-1
6 7
equipment
Heating
SSR NO
OUT1
▲
↓ The factory setting is 2 AT lamp ON, it goes off when auto-tuned.
T2 G
8 -
8
NC
7 19 Power supply
In most cases you should start-out by placing your con 8 20
AL2 set range: –1999-9999. + 6
troller in auto-tune mode. Once auto-tuned, your con B
4-20mA 9 TC 2 1
↓SET trollers should not require additional auto-tune cycle if 8 RTD
- 10 22
the environment its working in changes little. If your Malfunction estimate
AL2 mode: The same as AL1.
controllers is being used to heat or cool a load with a large A 11 23
TA6/TA8/TA9 are subject to the drawing ① No Display : Check all the connection and wiring if it is all
↓ SET thermal mass, then the auto-tuned values need to be re on the product. B
12 24
correct. Specially pay attention to the power supply terminals and
Offset value,range: ±100. duced by 5% -10%. signal input ternimals.
Display valuePV = Measured value - PVF ON/OFF control: ▲ Set value
↓ SET
The CtL setting.In most cases our control cycle should be
← ② Incorrect Didplay: Check if the input signal is conformity with
ON OFF
↑
↑
Input signal selection set to 10-20 seconds. For heating or coolin a load with a Heating HYS
LO
Cooling OFF HYS ON
▲ HI
↑ the selected symbol.
stands for K, J, E, S,Pt100,Cu50 or mA/V/mV large thermal mass, the value should be set to 30-40 LO ▲ HI For TC input, please use the relative compensation cable.
The factory setting is K seconds. If you are using a controller with a relay, setting Alarm mode:▲ Set value △ Alarm value AL
↓SET For RTD input, please use low impedence cable. The 3 wires
longer values will help to extend the life of your relay
↑←
OFF HY ON should at the same length.
Proportional band (%) range 0.1-3600.
contacts. Unless your process dictates longer cycle times, 0:Deviation HI alarm
If P=OFF, it means ON/OFF control LO▲ △ HI If all above mentioned is collect , pleaase use parameter
↓SET the value should be set to 1-3 seconds to non-relay(SSR) PVF to modify.
↑←
ON HY OFF
Integral time range 0.1-3600. controls.The value should be set to 000 if 4-20mA cur 1: Deviatian LO alarm ③ Incorrect Control : If the instrument has been used for a long
I=OFF means cancel integral time. rent controls. LO △ ▲ HI time, the user find the temperature is hard to rise up to the set
↓SET value, meanwhile the outsidesystem running well, there must be
↑←
Terminal configurations OFF HY ON
Derivative time range 0.1-3600. D=OFF means 2: Absolute value HI alarm
(If any changed, please refer to the product showing.) something wrong with the parameters of the instrument.
cancel derivative time. LO▲ △ HI
The user need to re-autotuning the instrument. If the instrument
↓SET -
← B ON OFF
1 7 ↑← HY
TC/mV