Professional Documents
Culture Documents
SVC Tool
Key function
Service Tool
MCS Mode Function Move to higher menu
1 2 3
Set GO ON Go on next display (GO ON)
ON UP DOWN
GO BACK Go back previous display (Shift +GO ON)
0 GO ON CLEAR
Shif CLEAR
OFF GO BACK ENTER Clear: Delete last contents
t
ENTER Enter: To set input display (Shift+CLEAR)
SVC Tool
7. VANES
8. ENGINEERING
SVC Tool
1. System 1. ARO
2. Input 9. Memory
3. Output
SVC Tool
1. STATUS 2. TEST
1. System 1. ARO
2. Input 9. Memory
3. Output
Frequent used menu
M-1-1-2-1 Monitoring
GECB Event
M-1-1-2-7 Clearing
M2-2-1 Monitoring
GDCB Event
M2-2-3 Clearing
M1-1-1-1 Car status
A – 01 IDL ST ][ ][
C> U00 D00 A 1C
Display Meaning Value
1 A Car ID (Lift No.) A-D : Car ID in group mode.
12 3 4 5 6 7
- Stop
A - 01 IDL ST ][ ][ Running
2 - u Up running
C> U00D00 A 1C direction
d Down running
3 01 Car position ** Unknown position 00-31 Current position
Operation
4 IDL Refer to the table on next page
mode
<GOON>
Call type change
/<GOBACK>
A – 01 IDL ST ][ ][
<0 … 9> Floor selection
C> U00 D00 A 1C
<ENTER> Call input setting
110% 20%
SVC Tool
SVC Tool
SVC Tool
SVC Tool
Input List
DZ Door Zone Door Zone (LV1 & LV2) 도어존 (LV1 & LV2)
GECB Error
To check previous / late
00021 saved Runs (Number of operation) <GOON> /<GOBACK>
event (page)
000153 saved Mins (Minutes of operation) <UP> / <DOWN> Event initialization
1
0204 TCI/ERO on. 1 0204 TCI/ERO on Event No. & title Refer to Event List for details
c003 t00020 p**.
2 3 4
2 003 No. of same event occurred 0 – 999
Erase EVENTS ?
n=0 y=1
“1” set then
Shift + Enter
Erase EVENTS ?
n=0 y=2
“2” set then
Shift + Enter
Erase Events !
done !
Install Menu / <M1-1-3-1- * >
GOON /
INSTALL – Menu > GOBACK
To check previous / late page parameter group
01 System
0 … 9 To jump selected parameter group
To go selected parameter group, save new setting value
ENTER
(Parameter value can be changed as elevator stops)
This function is to mask floor data and there are 4 types of allowed mask.
Pos.Ind new
ENTER To save new inputted code
at: R 00 = 03 >
Display description values
Pos.Ind. new 1 L L: Left letter, R: Right letter
at: L 00 =10 > Floor number
1 2 3 2 00
(GOON for increase floor)
00-31
Pos.Ind. new
at: L 00 =10 >01 3 10 Code for display 00-39 (Refer to below)
4 4 01 New inputted code 00-39 (Refer to below)
GO ON
LEARN RUN (M2-4-1)
GOON
2
“1” key in
3
“1” key in
4
“1” key in
Continuous on next page
LEARN RUN (M2-4-1)
5 10
Learn active
Switch to ERO CAR MOVES UP
11
6
L001 10000.0mm During Learn Run, PRS length &
To start learn - floor height will be displayed
vane 250.0mm
run press ENTER
Shift + Enter 12
7
TABLE STORED IN
Switch back to ”ERO” to “NORMAL” E2PROM >
NORMAL
GOON
13
8
It will be displayed, if Load Weigh Type
HITCH LOADW is “2” . (M2-3-1), In case of PTM applied,
FIND BOTTOM LDG, Car move to the bottom
floor. CALI DONE > it won’t be displayed
moving down : - -
GOON
14
9
LEARN RUN 4-1
BOTTOM LDG: start < >
Press “1” to start Learn Run
learn? y=1/n=0
“1” key in Note FIND BOTTOM LDG, If car is not bottom floor, car will move to
moving Up : - - bottom floor
LEARN RUN (M2-4-1)
No LS signals
No CAN communication with GECD or LS signal not detected more than 2 seconds
=> abort >
RUN IN PROGRESS
In case that car runs as Learn Run is activated
=> abort >
SIG NOISE/BOUNCE PRS signal is not clear due to noise or poor contact
=> abort > To check installation condition & wiring of 1LV,2LV, UIS, DIS
PRS_SIG != 1VANE
If “vanes” of PRS sensor is detected as “0” or “2”
=> abort >
TRANSITN OVERDUE In case that signal of PRS Sensor is out of range. Need to check PRS type parameter
=> abort > (To check communication of car top RSL & condition of PRS Sensor )
DETECTED ## LDGs
In case No. of 1LS is not correct, to check No of 1LS of setup Parameter. (M-2-3-1)
in 1LS: abort >
1LS: ON->OFF->ON
If 1LS signal is detected as ON/OFF/ON To check 1LS distance
gap => abort >
2LS OFF->ON->OFF
If 2LS signal is detected as ON/OFF/ON To check 2LS distance
gap => abort >
1LS/2LS OVERLAP!
In case both signals, 1LS & 2LS, are detected together.
=> abort >
VANE GAP SHORT: If length of PRS is detected as longer than parameter setting To check Vane Sensor
xxxxmm! abort > Type (M-2-3-1)
LR ABORTED!
Learn Run is failed due to the error of drive & GECB
see fault log >
LR ABORTED
Input of either ERO or TCI box is not correct
by ERO/TCI! >
FIND BOTLDG (2-4-3) (Finding bottom floor)
* This function should take precedence over Door Check Sequence (M1-1-3-5)
1 2
FIND-BOTTOM-LNDG
ERO ON Switch to ERO
RUN : press ENTER
Switch to ”ERO”
SHIFT + ENTER
5 6
to start DCS
press ENTER
[Purpose of DCS RUN]
Shift + Enter
* To check landing door contact.
* Elevator can operate only inspection mode before DCS RUN.
u00 DW:clsd ][ ][
up to next floor
...
GOON GOON
DCS Success full Check PES,GTC... to start normal! Normal operation
press GOON > press GOON > press GOON > after GOON
DCS- RUN Menu <M1-1-3-5> (Door check)
DCS- RUN Menu <M1-1-3-5> (Door check)
Front Door Error Car door opened but landing door switch not opened (Front)
Rear Door Error Car door opened but landing door switch not opened (Rear)
DW not closed Car door closed but landing door switch not closed
Setting Time
“30” - day will be flickering
30.05.11 19.01
GOON
Current Time
30.05. 19:02:08
STATUS (M2-1-1)
▣ STATUS (Status)
Display Description Value
Drive Error
To display the detail of each event, press “SHIFT + ENTER” at the display of event
SHIFT+ENTER
Shift + Enter
(Condition of GDCB) (Normal run without error) (GDCB condition in error) (No. of error)
EVENT LOG 2 - 2 – 3
< >
Clear Log ?
Enter to Clear
Log event will be erased by pressing “SHIFT + ENTER”
Shift + Enter [For Current Event (2-2-1)]
Expiration NO EXPIRATION
Count = 000173 press ‘CLEAR’
M1-1-2-8