Professional Documents
Culture Documents
10
MODEL 171.4
P88.10-2159-09
1 Front fender
10 Spacer
14 Rivet
15 Retaining rail
P88.10-2160-04
Remove
1 Open engine hood and raise to vertical AR88.40-P-1000V
position
2 Remove bolts (13) Rechargeable drill / screwdriver
3 Remove left and right door sill molding AR68.30-P-4100V
4 Remove inner fender rear section in left and AR88.10-P-1300V
right rear front fender (1)
5.1 Remove windshield washer fluid reservoir When removing right fender (1) AR82.35-P-6000V
6 Loosen inner fender rear section in left and See:
right rear front fender (1) until bolts (3, 5, 6)
are accessible.
Remove/install fender liner in front fender AR88.10-P-1300V
7 Loosen longitudinal member (8) from Carefully unclip longitudinal member (8)
longitudinal member in front area with Otherwise the longitudinal member paneling
mounting wedge until nuts (9) are accessible (8) can be damaged.
*110589035900
8 Unscrew nuts (9) Rechargeable drill / screwdriver
9 Unscrew bolts (3) from front bumper (4) Rechargeable drill / screwdriver
10 Unscrew bolt (5) from lamp unit mount (7) Rechargeable drill / screwdriver
11 Loosen bolt (6) on lamp unit mount (7) Rechargeable drill / screwdriver
12 Remove bolts (2) Rechargeable drill / screwdriver
© Daimler AG, 7/24/17, L/07/17, ar88.10-p-1000v, Remove/install front fenders Page 1 of 3
MODEL 171.4
13 Remove front fender (1) Carefully remove front fender (1) to
prevent damaging pain on adjacent
detachable body components and front fender
(1).
14.1 Drill out rivets (14) and remove retaining strip When replacing front fender (1)
(15) from front fender (1)
Rechargeable drill / screwdriver
Install
15.1 Glue new spacer (10) to front fender (1). When replacing front fender (1)
16.1 Rivet retaining strip (15) with front fender (1) When replacing front fender (1)
Hand riveter
17 Position front fender (1) at installation location Carefully position front fender (1) to
and fasten with nuts (9) and bolts (3, 5, 6) prevent damaging point on adjacent
detachable body components and on front
fender (1).
18 Adjust transition and gap between front fender The transition in the lower area of the front
(1) and front door and A-pillar and tighten fender (1) to the door can also be adjusted by
bolts (2). the screw-in depth of the adjustment screws
(11).
Gap between front door to fender and gap *BE60.00-P-1002-01L
between fender to A-pillar
*129589032100
19 Tighten nuts (9) *BA88.10-P-1003-01B
20 Lower vehicle with vehicle lift
21 Adjust gap between front fender (1) and Gap, engine hood to fender *BE60.00-P-1001-01L
engine hood and tighten bolts (13)
*BA88.10-P-1002-01B
*129589032100
22 Raise vehicle with vehicle lift AR00.60-P-1000V
23 Tighten bolts (3, 5, 6) on front bumper (4) and Observe transition between front fender
lamp unit mount (7) (1) and front lamp unit and front bumper (4).
24.1 Install washer fluid reservoir of windshield When installing right front fender AR82.35-P-6000V
washer system (1).
25 Install inner fender rear section in left and AR88.10-P-1300V
right front fender (1).
26 Fasten inner fender front section in left and See:
right front fender (1).
Remove/install fender liner in front fender AR88.10-P-1300V
27 Fasten longitudinal member paneling (8)
28 Install left and right door sill molding AR68.30-P-4100V
29 Repair paint damage on visible screw heads
with touch-up paint pen
30 Close engine hood AR88.40-P-1000V
31.1 Install model designation on front fender (1) When replacing front fender (1) on model AR88.10-P-1001V
171.442 up to production date 2.10.05.
Fender