Professional Documents
Culture Documents
STOPAQ® BASECOAT
®
Product properties of Stopaq Basecoat
Product Information Colour Green
Thickness 1.0 ± 0.1 mm
®
Product description: Stopaq Basecoat is a unique, cost-effective Density 1.5 ± 0.1 g/cm³ (ISO 1183-1)
product intended to be used for a wide range of structural applications Temperature Operation: -45°C up to +50°C
where water ingress and/or corrosion is a problem. Stopaq® Basecoat is ranges Substrate during -10°C up to +50°C
easy to install offering excellent corrosion preventing properties. The application:
material has a greyish polyester non-woven fibre top layer that allows for Water absorption Basecoat compound: < 0.03% (ASTM D570)
immediate painting or coating after installation. The product offers a Peel test Tested at +23°C and +50°C at a rate of 100
long-term performance in e.g. commercial, residential, utilities,
mm/min on steel substrate (ASTM D1000):
telecommunications, transportation, electrical, water, wastewater,
Cohesive failure, no signs of adhesive
agricultural, and industrial uses.
failure
Stopaq® Basecoat is a low temperature cold-applied, non-crosslinked, Residual corrosion preventing film
remaining on substrate, coverage >95%
non-crystalline, monolithic viscous polymer based patch coating material
with cold flow, visco-elastic properties. It is a non-toxic material adhering Thermal ageing Accelerated ageing during 100 days@+70°C in
extremely well to metals like bare steel and to substrates like PE, PP, resistance and hot dry atmosphere and immersed in hot water:
and coated steel. It is fully resistant to water and has a very low gas- water immersion Results of peel test after ageing were not
and water vapour permeability. Stopaq® Basecoat is viscous at the test affected: cohesive failure, no signs of adhesive
indicated operating temperatures and, due to its liquid nature, flows into failure, and residual corrosion preventing film
all irregularities of the substrate. The compound does not cure and is remaining on substrate.
unable to build up internal stress.
General order information
Stopaq® Basecoat can be coated with several types of top-coatings, e.g. Product Stopaq® Basecoat is available in
2-component coatings like polysiloxanes, epoxies or polyurethanes, or rolls of various widths and lengths:
1-component coatings like waterborne acrylics. Please contact Seal For Product dimensions and contents:
Life Industries B.V. for additional information. 200mm x 20m, 2 rolls/box, 96 rolls/pallet
Other sizes on request.
Features: Handling Handle with care. Keep boxes upright.
Surface tolerant – e.g. for steel substrates blasting techniques are not Storage Store indoor, clean and dry, away from direct
required, wire brushing is sufficient (ISO 8501-1: St 2) sunlight in a cool place below +35°C. Unlimited
Low surface tension; adheres on many types of dry substrates at a shelf life.
molecular level
Can be applied in high-humidity atmospheres
Resistance to low temperatures without getting brittle
Controlled cold flow providing permanent inflow into the finest pores of
the substrate
Adhesion based on vanderWaals forces
Conforms to many irregular shapes
Constant film thickness
No osmosis or underfilm migration of water
Inert to ageing and weathering
Resistant to many chemicals like water, salts, and polar solvents. For
additional information, please contact Seal For Life industries B.V.
Benefits:
Environmentally friendly, no health and safety hazards to humans
Fast and easy to apply at low temperatures
Easy to control during application
Can be moulded onto various types of irregular shaped objects
Application examples
DISCLAIMER: Berry Plastics warrants that the product(s) represented within conform(s) to its/their chemical and physical description and is appropriate for the use as stated on the respective technical
data sheet when used in compliance with Berry Plastics written instructions. Since many installation factors are beyond the control of Berry Plastics, the user is obligated to determine the suitability of the
products for the intended use and assume all risks and liabilities in connection herewith. Berry Plastics liability is stated in the standard terms and conditions of sale. Berry Plastics makes no other
warranty either expressed or implied. All information contained in the respective technical data sheet(s) should be used as a guide and is subject to change without notice. This document supersedes all
previous revisions. Please see revision date on the left. Stopaq® is a registered trademark of Berry Plastics Corporation.
V 1 / 20130403 (EN) Page 2 / 2