Professional Documents
Culture Documents
Date: 01/09/07
High Strength Structural Bolting BOLT - Property Class 8.8 Approved: M.R. Tiddy
Assemblies for Preloading Page: 1 of 6
Thread size d M12 M16 M20 M22 M24 M27 M30 M36 General Requirements BS EN 14399-1
Materials & Manufacture BS EN ISO 898-1 Property Class 8.8
P pitch of thread 1.75 2 2.5 2.5 3 3 3.5 4
Self Colour / Black BS EN 14399-3 - as processed
Bolt ≤ 125 30 38 46 50 54 60 66 78 Finish /
Zinc Electroplated BS 7371-3 or BS EN ISO 4042
Bolt > 125 Coatings
b < 200
- 44 52 56 60 66 72 84 Hot Dip Galvanized BS EN ISO 10684
Bolt > 200 - - 65 69 73 79 85 97 Mechanical Properties BS EN 14399-3, BS EN ISO 898-1 8.8
Dimensions & Tolerances BS EN 14399-3
max. 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8
c Threads ISO 261, ISO 965-2 tolerance class 6g
min. 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Product Marking BS EN 14399-3
da max. 15.2 19.2 24.4 26.4 28.4 32.4 35.4 42.4
max. 12.70 16.70 20.84 22.84 24.84 27.84 30.84 37.00 Important Note
ds
min. 11.30 15.30 19.16 21.16 23.16 26.16 29.16 35.00
It is a requirement of BS EN 14399 that
dw1) min. 20.1 24.9 29.5 33.3 38.0 42.8 46.6 55.9
e min. 23.91 29.56 35.03 39.55 45.20 50.85 55.37 66.44 The bolt, nut and washer assembly is supplied by one
max. 7.95 10.75 13.40 14.90 15.90 17.90 19.75 23.55 manufacturer who is responsible for the function of the
k assembly.
min. 7.05 9.25 11.60 13.10 14.10 16.10 17.65 21.45
r min. 1.2 1.2 1.5 1.5 1.5 2.0 2.0 2.0 All the components are identified with the
max. 22 27 32 36 41 46 50 60 manufacturer’s mark.
s
min. 21.16 26.16 31 35 40 45 49 58.8 The coating of the assembly is under the control of the
¹) The maximum value of dw shall not exceed the actual width across flats manufacturer.
Dimensions apply prior to coating
�
�
��
�� � 8.8HR
�
� � �
Thread size d M12 M16 M20 M22 M24 M27 M30 M36 General Requirements BS EN 14399-1
P pitch of thread 1.75 2 2.5 2.5 3 3 3.5 4 Materials & Manufacture BS EN 20898-2 Property Classes 8 & 10
max. 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 Self Colour / Black BS EN 14399-3 - as processed
c Finish /
min. 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 Zinc Electroplated BS 7371-3 or BS EN ISO 4042
Coatings
dw1) min. 20.1 24.9 29.5 33.3 38.0 42.8 46.6 55.9 Hot Dip Galvanized BS EN ISO 10684
e min. 23.91 29.56 35.03 39.55 45.20 50.85 55.37 66.44 BS EN 14399-3
Mechanical Properties
BS EN 20898-2 Classes 8 & 10
max. 10.8 14.8 18 19.4 21.5 23.8 25.6 31
m Dimensions & Tolerances BS EN 14399-3
min. 10.37 14.1 16.9 18.1 20.2 22.5 24.3 29.4
ISO 261
Threads
max. 22 27 32 36 41 46 50 60 ISO 965-2 tolerance Class 6H or 6AZ
s
min. 21.16 26.16 31 35 40 45 49 58.8 Product Marking BS EN 14399-3
¹) The maximum value of dw shall not exceed the actual width across flats
15o to 30o
Dimensions apply prior to coating
c
odw
e
m od s
All dimensions are in millimetres
BS EN 14399-3 Issue: 2
Date: 01/09/07
High Strength Structural Bolting NUT - Property Classes 8 & 10 Approved: M.R. Tiddy
Assemblies for Preloading Page: 5 of 6
BS EN 14399-3 Proof load values of property classes 8 & 10 nuts BS EN 14399-3 Nut Marking
Property Class
Stress Area Test 8 10
Nut thread Mandrel
Dia. Tolerance class Tolerance class
6H1) or 6AZ1) 6H1) or 6AZ1)
10HR
Property Class 10
��
��
�
���
H �
All dimensions are in millimetres Whilst this information is provided in good faith, no member of the Andaray group of companies shall be under any responsibility
or liability in respect of errors or information that is found to be incorrect or for any relience the user may place on it.