Professional Documents
Culture Documents
Version : A.002
Issue Date : 2008/12/09
File Name : SP-DD311-A.002.doc
Total Pages : 19
新竹市科學園區展業一路 9 號 7 樓之 1
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel:886-3-5645656 Fax:886-3-5645626
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656 Fax:886-3-5645626
DD311
DD311
General Description
DD311 is a single-channel constant current LED driver, which incorporates current mirror and
current switch, designed to drive power LEDs. It can provide a maximum sink current of 1A,
adjustable by reference current input. The output current is 100 times the input current value set by
an external resistor or bias voltage. Tuning or enabling the bias voltage can provide dot correction or
global brightness control in LEDs system. The Maximum output voltage of 36V can provide more
series power LEDs in a string. The output enable allows dimming control applications.
Features
Applications
Package Types
z TO-252
Block Diagram
Vbias VLED
IREF ILED
REXT OUT
EN
1 : 100
VSS GND
Pin Connection
1 2 3 4 5
EN
GND
REXT
VSS
OUT
Pin Description
*1
Output Voltage Vout Driver On 1 ⎯ ⎯
V
*2
Output Voltage Vout Driver Off ⎯ ⎯ 36
VEN(IH) 3.3 ⎯ 18
Input Enable Voltage IREF = 1mA ~ 10mA V
VEN(IL) -0.3 ⎯ 0.0
*1
Notice that the power dissipation is limited to its package and ambient temperature.
*2
The driver output voltage including any overshoot stress has to be compliant with the maximum voltage (33V).
Vout = 36 V
Output Leakage Current IOL1 ⎯ ⎯ 0.1 uA
Ven = 0V
*1
Chip-to-Chip skew is defined as the range into which any ratio between output current and reference current of any IC
falls.
VL
IREF
RL
R
EN
C VSS GND
CL
Transient Characteristics
Constant-Current Output
Constant-current value is set by the reference current input. The output current will be 100
times the input current value produced by an external resistor between the REXT pin and the bias
voltage*2 or, alternatively, force the low bias voltage to REXT pin. Varying the resistor or the bias
voltage value can adjust the current scale ranging up to 1A. Notice that the output current is a little
increasing or decreasing until the device temperature and ambient temperature are balance. The
output current value is calculated roughly by the following equation:
ILED (A) ~ 100 × ( Vbias- VREXT ) / REXT (ohm) = 100 × IREF (A)
*2
The variation of bias voltage influences the output stability directly.
1000
Vbias=36V
900
Vbias=24V
800 Vbias=18V
700 Vbias=12V
ILED (mA)
600 Vbias=5V
500
400
300
200
100
0
100 1000 10000 100000
REXT (ohm)
VLED Vbias
IREF REXT
ILED DD311
1 2 3 4 5
VREXT
EN
VLED Vbias
ILED DD311
1 2 3 4 5
EN
600
500
400
300
200
100
0
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8
Vbias (volt)
Iout = 1A
1.0
Iout=750m
0.8
Iout (A)
Iout=500m
0.6
Iout=350m
0.4
0.2
Iout=100m
0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
Vout (volt)
1100 1007.0
Iout=1A
1000
1006.5
900
800 Iout=750mA
1006.0
700
Iout (mA)
Iout (mA)
600 1005.5
Iout=500mA
500
1005.0
400 Iout=350mA
300 1004.5
Vout = 1V
200 Vout = 1V, VEN = 12V
Iout=100mA 1004.0 VEN = 12V
100
0 1003.5
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
Ambient Temperature (°C) Ambient Temperature (°C)
762 505
504
761
503
760
502
Iout (mA)
Iout (mA)
759
501
758
500
757
Vout = 1V 499 Vout = 1V
756 VEN = 12V 498 VEN = 12V
755 497
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
357 102.0
101.8
356 101.6
101.4
355
101.2
Iout (mA)
Iout (mA)
101.0
354
100.8
100.6
353
Vout = 1V 100.4
Vout = 1V
352 100.2
VEN = 12V VEN = 12V
100.0
351 99.8
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
1100 1020
Iout=1A
1000
900
1010
800 Iout=750mA
700
Iout (mA)
Iout (mA)
1000
600
Iout=500mA
500
Iout=350mA 990
400
300
Vout = 1V
200 Vout = 1V, Ta = 25°C 980
Iout=100mA Ta = 25°C
100
0 970
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
VEN (volt) VEN (volt)
764 509
762
508
760
Iout (mA)
Iout (mA)
758
507
756
754 Vout = 1V
Vout = 1V 506
750 505
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
353.5 100.80
353.0 100.75
Iout (mA)
Iout (mA)
352.5 100.70
351.5 100.60
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Power Dissipation
Notice that the power dissipation of a semiconductor chip is limited to its package and ambient
temperature, in which the device requires the maximum output current calculated for given
operating conditions. The maximum allowable power consumption can be calculated by the
following equation:
The relationship between power dissipation and operating temperature can be refer to the figure
below:
5.0
4.5
Tj(max)=125 °C
Power Dissipation Pd(W)
4.0
Rth=23.38 °C/Watt
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0 20 40 60 80 100 120 140
Based on the Pd(max), the maximum allowable voltage of output terminal can be calculated as
follows:
Typical Application
VLED
1 2 3 4 5
EN
VLED
Optional
In I2 I1
REXT DD311
1 2 3 4 5
EN
Paralleled Strings
VLED
Optional
In I2 I1
REXT
Optional
DD311
1 2 3 4 5
EN
VLED
Tel:886-3-5645656
Typical Application
新竹市科學園區展業一路 9 號 7 樓之 1
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
Fax:886-3-5645626
EN EN EN
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
GND
Version:A.002
ILED REXT DD311 ILED REXT DD311 ILED REXT DD311
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
EN EN EN
GND
Page 13
DD311
VLED
Typical Application
新竹市科學園區展業一路 9 號 7 樓之 1
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
Fax:886-3-5645626
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
VCC
DD311 is specifically designed to withstand high frequency Pull-High Resistance
3 14
typical application, a PWM enabled RGB driver DM413 is
4 13
configured to act as PWM signal generator. Through serial data DM413
Version:A.002
5 12
7 10
grayscale signal to control a set of three DD311. The combination
8 9
of DD311 and DM413 offers an ideal solution for high end
GND
grayscale control and color manipulation.
Page 14
DD311
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656 Fax:886-3-5645626
DD311
IC
TO252
Tube
53cm
Box
40 Tubes per Box
17cm
10cm
61cm
4 Boxes per Carton
Carton
35cm 24cm
64cm
Weight
Item Description Weight ( Kg )
1 80 pcs DD311-TO252EX per Tube 0.046±5%
2 Net Weight of one Box 0.40±5%
3 Net Weight of one Carton 1.24±5%
4 Per Carton Set ( 4 Boxes, 12,800 pcs ) 10.20±5%
IC
TO252
Tube
53cm
Box
40 Tubes per Box
17cm
10cm
61cm
34cm
64cm
Weight
Item Description Weight ( Kg )
1 80 pcs DD311-TO252EX per Tube 0.046±5%
2 Net Weight of one Box 0.40±5%
3 Net Weight of one Carton 1.44±5%
4 Per Carton Set ( 6 Boxes, 19,200 pcs ) 14.88±5%
The products listed herein are designed for ordinary electronic applications, such as
electrical appliances, audio-visual equipment, communications devices and so on. Hence,
it is advisable that the devices should not be used in medical instruments, surgical
implants, aerospace machinery, nuclear power control systems, disaster/crime-prevention
equipment and the like. Misusing those products may directly or indirectly endanger
human life, or cause injury and property loss.
Silicon Touch Technology, Inc. will not take any responsibilities regarding the misusage
of the products mentioned above. Anyone who purchases any products described herein
with the above-mentioned intention or with such misused applications should accept full
responsibility and indemnify. Silicon Touch Technology, Inc. and its distributors and all
their officers and employees shall defend jointly and severally against any and all claims
and litigation and all damages, cost and expenses associated with such intention and
manipulation.