Professional Documents
Culture Documents
20071112
Displays “Err”, if the input is invalid.
5011666101-K201
[ How to Operate the Digital Keypad
Setting Mode
START
NOTE:In the parameter setting mode, you can press to the selected mode.
To change data
Y Dimensions in mm [inch]
71.9 [2.83] 25.9 [1.02] 8.6 [0.34]
M3*0.5(2X)
52.4 [2.06] Y 鍵盤面板鍵盤面板尺寸
Setting PLC Mode 71.9 [2.83] 25.9 [1.02] 8.6 [0.34] 52.4 [2.06]
M3*0.5(2X)
42.4 [1.67]
34.3 [1.35]
42.4 [1.67]
34.3 [1.35]
PLC2 mode active
8.1 [0.32]
PLC1 mode active
\ Installation
Method 1. Direct installation (unit: mm[inch])
Z Display Messages
Display Message Descriptions Z 功能顯示項目說明
Displays the AC drive Master Frequency. 顯示項目 說明
顯示驅動器目前的設定頻率
Displays the actual output frequency at terminals U/T1, V/T2, and W/T3.
顯示驅動器實際輸出到馬達的頻率
User defined unit (where U = F x Pr.00.05)
顯示用戶定義之物理量 (U = F x 00-05)
Displays the output current at terminals U/T1, V/T2, and W/T3. Method 2. Mounting by the plate thickness (unit: mm[inch]) 顯示負載電流
A. Thickness=1.2mm[0.05 inches]
Displays the AC motor drive forward run status. 正轉命令
顯示計數值
The counter value (C).
顯示參數項目
Displays the selected parameter.
顯示參數內容值
B. Thickness=2.0mm[0.08 inches]
Displays the actual stored value of the selected parameter.
外部異常顯示
說明書 參數設定
參數設定 請詳細閱讀下列說明後才使用本產品,以確保使用安全。
由於產品精益求精,當內容規格有所修正時,請洽詢代理商或至台達網站 或
或
(http://www.delta.com.tw/industrialautomation)下載最新版本。 顯示輸入 顯示輸入
顯示輸入 顯示輸入
資料正確 資料錯誤 X 鍵盤面板外觀 重點:在參數設定模式中
資料正確
可往返回畫面選擇模式
資料錯誤
重點:在參數設定模式中 可往返回畫面選擇模式
資料 修改
資料修改
START
START
轉向設定 (運轉命令來源為數位操作面版時)
轉向設定 (運轉命令來源為數位操作面版時)
PLC模式設定
PLC模式設定
進入PLC2模式
or
進入PLC2模式 Y 鍵盤面板鍵盤面板尺寸 or
進入PLC1模式 \ 安裝方法
42.4 [1.67]
34.3 [1.35]
\ 安裝方法 方法 1. 直接安裝 (單位: mm[inch])
8.1 [0.32]
Z 功能顯示項目說明
顯示項目 說明
方法 2. 依板厚來安裝 (單位: mm[inch])
顯示驅動器目前的設定頻率
A. 板厚=1.2mm[0.05 inches]
方法 2. 依板厚來安裝 (單位: mm[inch]) 顯示驅動器實際輸出到馬達的頻率
A. 板厚=1.2mm[0.05 inches] 顯示用戶定義之物理量 (U = F x 00-05)
顯示負載電流
正轉命令
顯示參數內容值
外部異常顯示
若由顯示區讀到 End 的訊息(如左圖所示)大約一秒鐘,表示資料已被接受並自
動存入內部存貯器
若設定的資料不被接受或數值超出時即會顯示