Professional Documents
Culture Documents
PA66 BASF
An easy flowing injection moulding grade for fast processing. Used for highly stressed technical parts, such as bearings and gear wheels.
Rheological properties dry / cond Unit Test Standard
ISO Data
Melt volume-flow rate, MVR 120 / * cm³/10min ISO 1133
Temperature 275 / * °C -
Load 5/* kg -
Molding shrinkage, parallel 1.5 / * % ISO 294-4, 2577
Molding shrinkage, normal 1.8 / * % ISO 294-4, 2577
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 1/8
Ultramid® A3K
PA66 BASF
Diagrams
1E5
Shearstress in Pa
Viscosity in Pa s
1E2 1E4
1E3
1E1 1E2
1E0 1E1 1E2 1E3 1E4 1E5 1E0 1E1 1E2 1E3 1E4 1E5
1E4 1E4
G' G'
Shear modulus in MPa
1E3 1E3
1E2 1E2
1E1 1E1
-50 0 50 100 150 200 250 -50 0 50 100 150 200 250 300
Temperature in °C Temperature in °C
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 2/8
Ultramid® A3K
PA66 BASF
Stress-strain Stress-strain
Stress-Strain Stress-Strain
Ultramid® A3K (dry) Ultramid® A3K (cond.)
Stress in MPa
150 °C Y 150 °C
Y B - Break B - Break
60 Y - Yield 60 Y - Yield
Y Y
40 Y 40
Y
Y Y
Y Y
Y Y
Y
20 20 Y
0 0
0 10 20 30 40 50 0 10 20 30 40 50
Strain in % Strain in %
2500
100 °C 100 °C
120 °C 120 °C
B 150 °C 150 °C
2000 B B - Break B - Break
Y
YB Y - Yield 2000 Y - Yield
1500
1000 B
1000
Y
500
Y
Y Y Y
Y YY Y Y Y YY Y
0 0
0 10 20 30 40 50 0 10 20 30 40 50
Strain in % Strain in %
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 3/8
Ultramid® A3K
PA66 BASF
20 10 h 1000 2 MPa
100 h 4 MPa
1000 h 900 6 MPa
600
10
500
400
300
5 1E1 1E2 1E3 1E4 1E5
Time in h
0
0 1 2 3 4 5
Strain in %
20 10 h 600 5 MPa
100 h 10 MPa
1000 h 550 15 MPa
Creep modulus in MPa
10000 h 18 MPa
100000 h 500
15
450
Stress in MPa
400
350
10
300
250
200
5 1E1 1E2 1E3 1E4 1E5
Time in h
0
0 2 4 6 8
Strain in %
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 4/8
Ultramid® A3K
PA66 BASF
20 10 h 500 2 MPa
100 h 4 MPa
1000 h 450 6 MPa
300
10
250
200
150
5 1E1 1E2 1E3 1E4 1E5
Time in h
0
0 2 4 6 8
Strain in %
14 10 h 400 2 MPa
100 h 4 MPa
1000 h 6 MPa
Creep modulus in MPa
12 10000 h 8 MPa
100000 h 350 10 MPa
12 MPa
10
Stress in MPa
300
8
250
6
4 200
1E1 1E2 1E3 1E4 1E5
2
Time in h
0
0 1 2 3 4 5 6
Strain in %
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 5/8
Ultramid® A3K
PA66 BASF
Tensile modulus-temperature
Specific volume-temperature (pvT) Ultramid® A3K (dry)
Ultramid® A3K
1E4
1.1 0.1 MPa
40 MPa
Spec. volume in E-3 m³/kg
80 MPa
0.9
0.85
0 50 100 150 200 250 300
1E2
-50 0 50 100 150
Temperature in °C
Temperature in °C
Tensile modulus-temperature
Ultramid® A3K (cond.) Thermal Expansion
Ultramid® A3K
1E4
3 3 ?n
?p
2.5 2.5
Tensile modulus in MPa
2 2
1.5 1.5
?l/l0 in %
?l/l0 in %
1E3 1 1
0.5 0.5
0 0
-0.5 -0.5
-1 -1
1E2 -50 0 50 100 150 200
-50 0 50 100 150
Temperature in °C
Temperature in °C
Characteristics
Processing Additives
Injection Molding, Other Extrusion Lubricants, Release agent
Injection Molding
PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h
PROCESSING
injection molding, Melt temperature, range: 280 - 300 °C
injection molding, Melt temperature, recommended: 290 °C
injection molding, Mold temperature, range: 60 - 80 °C
injection molding, Mold temperature, recommended: 60 °C
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 6/8
Ultramid® A3K
PA66 BASF
Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)
Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C)
Toluene (23°C)
iso-Octane (23°C)
Ketones
Acetone (23°C)
Ethers
Diethyl ether (23°C)
Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
Standard Fuels
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)
Other
Ethyl Acetate (23°C)
Hydrogen peroxide (23°C)
DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
Water (23°C)
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 7/8
Ultramid® A3K
PA66 BASF
Disclaimer
Liability Exclusion
These guide values are measured and provided by the product manufacturer and have been determined on standardised test specimens and can be affected by pigmentation, mould design
and processing conditions. M-Base has taken the guide values from the producer's original Technical Data Sheet. ALBIS AND M-BASE ARE THEREFORE NOT RESPONSIBLE FOR THE
ACCURACY OF THE GUIDE VALUES AND CANNOT GIVE ANY WARRANTY WITH REGARD TO THEIR CORRECTNESS.
Any information given on the chemical and physical characteristics of our products, including, without limitation, technical advice on applications, whether verbally, in writing or by testing the
product, is given to the best of our knowledge and in good faith and does not exempt the buyer from carrying out their own investigations and tests in order to ascertain the product's specific
suitability for the purpose intended.
The buyer is solely responsible for confirming the suitability of the product for a particular application, its utilization and processing and must observe any applicable laws and government
regulations. NO EXPRESS OR IMPLIED RECOMMENDATION OR WARRANTY IS GIVEN WITH REGARD TO THE SUITABILITY OF THE PRODUCT FOR A PARTICULAR
APPLICATION, SUCH AS, BUT NOT LIMITED TO, SAFETY-CRITICAL COMPONENTS OR SYSTEMS.
Healthcare uses: the supply of any product by ALBIS for any medical, pharmaceutical or diagnostic application is conditional to an assessment by ALBIS in terms of compliance with ALBIS’
internal risk management policy – even for products which are in general designated for use in Healthcare applications.
Important: irrespective of product type or designation, ALBIS does not recommend or support the use of any products it supplies which fall into the following medical, pharmaceutical or
diagnostic application categories:
Created: 2023-02-14 Source: www.materialdatacenter.com Copyright M-Base Engineering+Software GmbH. Page: 8/8