Professional Documents
Culture Documents
Easy-flow, general purpose injection moulding grade with high resistance to impact and heat distortion; intended for a wide range of
applications, particularly in the housings sector.
Rheological properties Value Unit Test Standard
ISO Data
Melt volume-flow rate, MVR 19 cm³/10min ISO 1133
Temperature 220 °C -
Load 10 kg -
Created: 2024-03-05 Source: www.materialdatacenter.com Copyright Altair Engineering GmbH. Page: 1/5
Terluran® GP-22
ABS INEOS Styrolution
Diagrams
1E3
Shearstress in Pa
Viscosity in Pa s
1E2 1E5
1E1
1E0 1E4
1E1 1E2 1E3 1E4 1E5 1E1 1E2 1E3 1E4 1E5
Stress-Strain
Dynamic Shear modulus-temperature Terluran® GP-22
Terluran® GP-22
70 -40 °C
1E4 1E1
1E2 G' -20 °C
G" Y 0 °C
tan d 60 23 °C
1E3
Shear modulus in MPa
1E1 1E0 Y 40 °C
60 °C
80 °C
50
G'' in MPa
1E2 1E-1
1E0 Y - Yield
tan d
Stress in MPa
1E1 1E-2 40 Y
1E-1
Y
1E0 1E-3 30
1E-2
Y
1E-1 1E-4
1E-3 20 Y
-100 -50 0 50 100 150
Temperature in °C
10
0
0 1 2 3 4
Strain in %
Created: 2024-03-05 Source: www.materialdatacenter.com Copyright Altair Engineering GmbH. Page: 2/5
Terluran® GP-22
ABS INEOS Styrolution
Secant modulus-strain
Stress-strain (isochronous) 23°C
Terluran® GP-22
Terluran® GP-22
3000 -40 °C 20 10 h
-20 °C
0 °C 100 h
23 °C 1000 h
40 °C 10000 h
2500 100000 h
60 °C
80 °C 15
Secant modulus in MPa
Y - Yield
Stress in MPa
2000
Y Y
Y 10
1500 Y
Y 5
1000
Y
0
500 0 1 2 3 4 5
0 0.5 1 1.5 2 2.5 3 3.5 4
Strain in %
Strain in %
2500 14 10 h
5 MPa
10 MPa 100 h
15 MPa 1000 h
Creep modulus in MPa
1500 10
Stress in MPa
1000 8
500 6
0 4
1E1 1E2 1E3 1E4 1E5
2
Time in h
0
0 2 4 6 8 10 12 14
Strain in %
Created: 2024-03-05 Source: www.materialdatacenter.com Copyright Altair Engineering GmbH. Page: 3/5
Terluran® GP-22
ABS INEOS Styrolution
400
0.95
200
0 0.9
1E1 1E2 1E3 1E4 1E5 0 50 100 150 200 250 300
Time in h Temperature in °C
Tensile Modulus-Temperature
Tensile modulus-temperature
Terluran® GP-22
1E4
Tensile modulus in MPa
1E3
-40 -20 0 20 40 60 80
Temperature in °C
Characteristics
Delivery form
Pellets
Injection Molding
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h
PROCESSING
injection molding, Melt temperature, range: 220 - 260 °C
injection molding, Melt temperature, recommended: 250 °C
injection molding, Mold temperature, range: 30 - 60 °C
injection molding, Mold temperature, recommended: 50 °C
Created: 2024-03-05 Source: www.materialdatacenter.com Copyright Altair Engineering GmbH. Page: 4/5
Terluran® GP-22
ABS INEOS Styrolution
Disclaimer
Liability Exclusion
These guide values are measured and provided by the product manufacturer and have been determined on standardised test specimens and can be affected by pigmentation, mould design
and processing conditions. M-Base has taken the guide values from the producer's original Technical Data Sheet. ALBIS AND M-BASE ARE THEREFORE NOT RESPONSIBLE FOR THE
ACCURACY OF THE GUIDE VALUES AND CANNOT GIVE ANY WARRANTY WITH REGARD TO THEIR CORRECTNESS.
Any information given on the chemical and physical characteristics of our products, including, without limitation, technical advice on applications, whether verbally, in writing or by testing the
product, is given to the best of our knowledge and in good faith and does not exempt the buyer from carrying out their own investigations and tests in order to ascertain the product's specific
suitability for the purpose intended.
The buyer is solely responsible for confirming the suitability of the product for a particular application, its utilization and processing and must observe any applicable laws and government
regulations. NO EXPRESS OR IMPLIED RECOMMENDATION OR WARRANTY IS GIVEN WITH REGARD TO THE SUITABILITY OF THE PRODUCT FOR A PARTICULAR
APPLICATION, SUCH AS, BUT NOT LIMITED TO, SAFETY-CRITICAL COMPONENTS OR SYSTEMS.
Healthcare uses: the supply of any product by ALBIS for any medical, pharmaceutical or diagnostic application is conditional to an assessment by ALBIS in terms of compliance with ALBIS’
internal risk management policy – even for products which are in general designated for use in Healthcare applications.
Important: irrespective of product type or designation, ALBIS does not recommend or support the use of any products it supplies which fall into the following medical, pharmaceutical or
diagnostic application categories:
Created: 2024-03-05 Source: www.materialdatacenter.com Copyright Altair Engineering GmbH. Page: 5/5