GENERAL TERMS AND TESTING PROCESS GUIDELINES: -

TESTING PROCESS IMPORTANT GUIDELINES: -

1) Once article is opened it must be kept open for about 30 minutes (If possible, keep
article open in direct Sunlight for 30 minutes after opening the article)
2) After above process, bring the article in a dark room with only one candle lit on your
back side to give enough light for conducting the test, and make sure light does not fall
directly on X-ray films,
3) Bring X-ray film at about 45-degree angle down from about 10 inch towards open
article and moment you hear a sound hold it there for about 20 seconds (Please ensure
film should not touch the article). After 20 seconds film will be wet, and it must be dried
by clipping the same on a rope in dark room. On drying the film, it completes the x ray
film test and we need minimum 12 x-ray films or 2 kodak 400 color films with 8 shots
taken in each roll.
4) once article is brought inside the room or 30 minutes after opening the article, we need
to keep 2 torch (plastic body using Eveready batteries model 950, made of cardboard,
and ensure to keep a copper plate between the torch bottom spring and batteries.
Bring the torch at 45 degree angle towards the article slowly. Torch will start blinking and
get fused, keep torch 1 inch further from here at 45 degree. Please refer Diagram given
below). Keep the same for about 45 minutes.
5) Keep two No’s of Digital watches, by removing the back cover and keeping the same
facing article in vertical position, it must be kept exposed to article for about 30 minutes.
6) Keep two No’s Thermometer (One with Silver Mercury and Medium size) in front of
open article (Ref. attached diagram) for about 20 – 30 minutes.

To Summarize we need 12 x-ray films shots, 2 no’s Torch, 2 No’s Digital Watches, 2 No’s
Thermometer.

DISCLAIMER NOTICE: -

Above testing procedure and General Guidelines of Process are given for General understanding only and this may
vary with different articles and Article Owner require to take necessary precaution as per their article. One needs to
properly understand above process than according to their article Size and Strength take decision and further action,
GUIDELINES ON WORKING PROCESS : -

1. Testing should always be done on a bright sunny day and between Morning 9 AM
to 3 PM Noon, ideally it is by 12 noon when Sun is on its peak temperature. Avoid
testing on a cloudy day.
2. Once testing is done, we need you to send photograph of all 12 X-ray films along
with Photograph of Tested Bulb of 2 torch. Digital Watch’s dial both watches and
both thermometers as well,’
3. Once we send all the photograph, they will inform us back about acceptance or
authenticity of the article same day and welcome us, otherwise no further
interaction will be allowed.
4. We need to carry tested 12 x-ray films, 2 No’s each Torch, Digital Watches and
Thermometers, we must reach at the address provided by 8.30 in morning
5. Verification of tested article brought, and photograph will be first rechecked and on
satisfactory verification only owner will be taken to the lab for testing.
6. On successful testing, Owner will be taken to DAE Office in Kolkata for Registration
and Agreement of article, and then moved to a five star hotel.
7. If all above process are completing within the Banking hours than a Token will be
given to Owner after deducting TDS same day or it will be given next day by noon.
8. Effective from 1st January 2021 all National holidays will be closed, and registration
will be done on only Bank working days.
9. In Election period only registration and token will be provided, and further work will
start once the new government is sworn in.

DISCLAIMER NOTICE: -

Above testing procedure and General Guidelines of Process are given for General understanding only and this may
vary with different articles and Article Owner require to take necessary precaution as per their article. One needs to
properly understand above process than according to their article Size and Strength take decision and further action,