Professional Documents
Culture Documents
1. The holes around the center hole of a cutting tip are preheating flame holes.
True False
2. Both goggles and gloves must be worn during the cutting process for protection from
sparks, metal particles, and heat.
True False
4. Oxy-fuel gas cutting machines are able to cut only a limited number of designs.
True False
5. It is not possible to cut geometric designs into metal sheets without using templates.
True False
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
1
Chapter 06 Flame Cutting Principles
8. Fuel gas fittings have a left handed thread and have a groove machined into it.
True False
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
2
Chapter 06 Flame Cutting Principles
11. The only reason goggles should be worn is to protect the welder's eyes from glare.
True False
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
3
Chapter 06 Flame Cutting Principles
17. The oxy-fuel gas cutting process uses acetylene as a fuel gas as well as ____. (one wrong)
A. MAPP
B. nitrogen
C. natural gas
D. propane
18. The central hole in a cutting tip provides for the passage of ____.
A. acetylene
B. oxygen
C. hydrogen
D. propane
20. For plates up to 1/2-inch thick, ____ cutting is an efficient method of cutting several
thicknesses of material at once.
A. beam
B. magnet
C. oxygen lance
D. stack
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
4
Chapter 06 Flame Cutting Principles
21. A portable ____ cutter may be used for trimming and beveling angles and channels.
A. beam
B. magnet
C. oxygen lance
D. stack
22. A length of black iron pipe attached to a fuel source and used for cutting heavy sections of
steel is an oxygen ____ cutter.
A. beam
B. magnet
C. lance
D. stack
23. On a two gauge regulator, which gauge usually indicates the working pressure?
A. the one closest to the cylinder valve
B. the one furthest from the cylinder valve
C. both together
D. neither a or b.
24. Which of the following metals can be readily cut with the OFC process?
A. cast iron
B. monel
C. non-ferrous
D. low carbon steel.
25. Which of the following items of equipment is not required for OFC?
A. oxygen and fuel gas hoses
B. cutting torch with flame arresters and check valves
C. oxygen and fuel gas regulators
D. matches for lighting the torch.
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
5
Chapter 06 Flame Cutting Principles Key
1. The holes around the center hole of a cutting tip are preheating flame holes.
TRUE
2. Both goggles and gloves must be worn during the cutting process for protection from
sparks, metal particles, and heat.
TRUE
4. Oxy-fuel gas cutting machines are able to cut only a limited number of designs.
FALSE
5. It is not possible to cut geometric designs into metal sheets without using templates.
FALSE
8. Fuel gas fittings have a left handed thread and have a groove machined into it.
TRUE
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
6
Chapter 06 Flame Cutting Principles Key
11. The only reason goggles should be worn is to protect the welder's eyes from glare.
FALSE
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
7
Chapter 06 Flame Cutting Principles Key
17. The oxy-fuel gas cutting process uses acetylene as a fuel gas as well as ____. (one wrong)
A. MAPP
B. nitrogen
C. natural gas
D. propane
18. The central hole in a cutting tip provides for the passage of ____.
A. acetylene
B. oxygen
C. hydrogen
D. propane
20. For plates up to 1/2-inch thick, ____ cutting is an efficient method of cutting several
thicknesses of material at once.
A. beam
B. magnet
C. oxygen lance
D. stack
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
8
Chapter 06 Flame Cutting Principles Key
21. A portable ____ cutter may be used for trimming and beveling angles and channels.
A. beam
B. magnet
C. oxygen lance
D. stack
22. A length of black iron pipe attached to a fuel source and used for cutting heavy sections of
steel is an oxygen ____ cutter.
A. beam
B. magnet
C. lance
D. stack
23. On a two gauge regulator, which gauge usually indicates the working pressure?
A. the one closest to the cylinder valve
B. the one furthest from the cylinder valve
C. both together
D. neither a or b.
24. Which of the following metals can be readily cut with the OFC process?
A. cast iron
B. monel
C. non-ferrous
D. low carbon steel.
25. Which of the following items of equipment is not required for OFC?
A. oxygen and fuel gas hoses
B. cutting torch with flame arresters and check valves
C. oxygen and fuel gas regulators
D. matches for lighting the torch.
Copyright © McGraw-Hill Education. All rights reserved. No reproduction or distribution without the prior
written consent of McGraw-Hill Education.
9