Professional Documents
Culture Documents
RRV4498
DDJ-WEGO2-K
DJ Controller
DDJ-WEGO2-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
2 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 4
1.1 NOTES ON SOLDERING ............................................................................................................................................... 4 A
1.2 SERVICE NOTICE.......................................................................................................................................................... 4
2. SPECIFICATIONS................................................................................................................................................................. 5
3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 6
3.1 CHECK POINTS AFTER SERVICING ........................................................................................................................... 6
3.2 JIGS LIST ....................................................................................................................................................................... 6
3.3 PCB LOCATIONS ........................................................................................................................................................... 7
4. BLOCK DIAGRAM ................................................................................................................................................................ 8
4.1 OVERALL WIRING DIAGRAM ....................................................................................................................................... 8
4.2 OVERALL BLOCK DIAGRAM....................................................................................................................................... 10
5. DIAGNOSIS ........................................................................................................................................................................ 12
5.1 BOOT SEQUENCE....................................................................................................................................................... 12
5.2 TROUBLESHOOTING.................................................................................................................................................. 13 B
5.3 OPERATION CHECK WITH VIRTUAL DJ .................................................................................................................... 15
6. SERVICE MODE ................................................................................................................................................................. 17
6.1 FIRMWARE VERSION (MAIN UCOM) and LAST MEMORY CONFIRMATION MODE............................................... 18
6.2 BUTTON INPUT and DISPLAY FUNCTION CONFIRMATION MODE......................................................................... 20
6.3 JOG DIAL ROTATION TIME MEASUREMENT MODE................................................................................................. 23
6.4 FACTORY RESET MODE............................................................................................................................................. 24
6.5 iPhone/iPad CONNECTING CABLE CONFIRMATION MODE .................................................................................... 25
7. DISASSEMBLY ................................................................................................................................................................... 26
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 31
8.1 NECESSARY ITEMS TO BE NOTED........................................................................................................................... 31
8.2 UPDATING OF THE FIRMWARE ................................................................................................................................. 31
C
8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE........................................................................................... 32
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 34
9.1 PACKING SECTION ..................................................................................................................................................... 34
9.2 EXTERIOR SECTION .................................................................................................................................................. 36
10. SCHEMATIC DIAGRAM .................................................................................................................................................... 40
10.1 CONTROL PCB ASSY ............................................................................................................................................... 40
10.2 IO PCB ASSY ............................................................................................................................................................. 42
10.3 MASTER PCB ASSY.................................................................................................................................................. 44
10.4 WHELL (R) and (L) PCB ASSYS................................................................................................................................ 46
10.5 WAVEFORMS............................................................................................................................................................. 48
11. PCB CONNECTION DIAGRAM ........................................................................................................................................ 52
11.1 CONTROL PCB ASSY ............................................................................................................................................... 52 D
11.2 IO PCB ASSY ............................................................................................................................................................. 56
11.3 MASTER PCB ASSY.................................................................................................................................................. 58
11.4 WHELL (R) PCB ASSY .............................................................................................................................................. 59
11.5 WHEEL (L) PCB ASSY............................................................................................................................................... 60
12. PCB PARTS LIST .............................................................................................................................................................. 61
DDJ-WEGO2-K 3
5 6 7 8
1 2 3 4
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
A • For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
B
temperatures (hard to melt/easy to harden).
Basically, if both the iPhone/iPad connecting cable and the DDJ-WEGO2 are okay, the problem is on the connected iOS device
side.
4 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
General – Main Unit Accessories A
Power supply..........................................................................DC 5 V
Power consumption ...............................................................500 mA • VIRTUAL DJ LE software/driver software/operating instructions
Main unit weight (with iPhone/iPad stand mounted).... 1.8 kg (4.0 lb) CD-ROM
Maximum external dimensions (with iPhone/iPad stand mounted)
................380 mm (width) × 65 mm (height) × 250.6 mm (depth) • USB cable
(14.96 in. (width) × 2.56 in. (height) × 9.87 in. (depth)) (408-SUB-132)
Tolerable operating temperature. +5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity............. 5 % to 85 % (no condensation) • Read Before Use (Important)/Quick Start Guide
(XE5, XE25: 502-WG2A-3328A, 502-WG2A-3329A)
Audio Section (XECN5: 502-WG2B-3330)
Rated output level
MASTER OUT...................................................................+13 dBu • Warranty (for some regions)
Total harmonic distortion The included warranty is for the European region. B
MASTER OUT................................................................... 0.006 % — For the North American region, the corresponding information
Frequency characteristic isprovided on the last page of both the English and French
MASTER OUT.......................................................20 Hz to 20 kHz versions of the “Read Before Use (Important)/Quick Start
S/N ratio (when playing on computer) Guide”.
MASTER OUT.......................................... 101 dB (at rated output) — For the Japanese region, the corresponding information is
Input impedance provided on the last page of the Japanese version of the
MIC........................................................................................10 kΩ “Read Before Use (Important)/Quick Start Guide”.
Output impedance
MASTER OUT.........................................................................1 kΩ • iPhone/iPad connection cable (Lightning)
PHONES ............................................................................... 4.7 Ω (408-WG2-129)
USB AUDIO.............................24 bit/Fs: 44.1 kHz, 24 bit/Fs: 48 kHz
• iPhone/iPad stand
Input / Output terminals (DDJ-WEGO2-K: 701-WG2K-5403)
USB terminal (DDJ-WEGO2-R: 701-WG2R-5403) C
B type ..................................................................................... 1 set (DDJ-WEGO2-W: 701-WG2-5403)
MASTER OUT output terminal
RCA pin jacks ......................................................................... 1 set • Stand fixing screws x 3
PHONES output terminal (DDJ-WEGO2-K, DDJ-WEGO2-R: 602-SWISO415-745B)
Stereo phone jack (Ø 6.3 mm) ............................................... 1 set (DDJ-WEGO2-W: 602-SWISO415-745Z)
Stereo mini phone jack (Ø 3.5 mm)........................................ 1 set
MIC input terminal • VIRTUAL DJ LE license key (indicated on this unit’s bottom panel)
Phone jack (Ø 6.3 mm)........................................................... 1 set
iOS device connection terminal
14-pin...................................................................................... 1 set
DDJ-WEGO2-K 5
5 6 7 8
1 2 3 4
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
C
Distortion Volume too high
Noise Volume fluctuating
Volume too low Sound interrupted
D
3.2 JIGS LIST
Jigs List
Jig Name Part No. Purpose of use / Remarks
USB cable GGP1193 for PC connection
iPhone/iPad connection cable (Lightning) GGP1234 for iOS device connection
6 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
• Bottom view
E
NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
DDJ-WEGO2-K 7
5 6 7 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A
E WHEEL (L) PCB ASSY
(704-WG2-A610)
CN01B CN02B
A
B
CONTROL PCB ASSY
1 (704-WG2-A604) 2
G1B G5
G1A
C
W4A
CHASSIS 1
CN01A CN02A
W3A
IN1 G2
FGND
W01A
CN605
ISDA
D ISCL AGND
W01B ISCL
W4B
FGND
ISDA
W3B
W604
W02A W02B
3 5
CN605A
4 CN604
CN501
W501
8 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
CN01A 1 CN01B
A
WL 1A
1 1
WL 1B
2 2
A 3
DS1
STCP 5
3 E
4 4
CONTROL 5
SHCP 1
PWM1
5 WHEEL (L)
6 6
PCB ASSY 7
5V
7 PCB ASSY
DGND
8 8
FFC 8P FFC 8P
CN02A 2 CN02B
WL 1A
1 1
WL 1B
2 2
A 3
DS1
3 D
D WHEEL (R) PCB ASSY CONTROL
4
5
STCP 5
SHCP 1
PWM1
4
5 WHEEL (R) B
(704-WG2-A609) PCB ASSY
6
7
5V
DGND
6
7 PCB ASSY
8 8
FFC 8P FFC 8P
CN605 3 CN605A
ISDA
1 11
ISCL
2 10
5V
3 9
GND
A 4
5
A5V 8
7
B
PMUTE
CONTROL
6
7
REST 6
5
IO
INT
PCB ASSY 8
9
SCL 4
3
PCB ASSY
DGND
10 2
SDA
11 1 C
CHASSIS 2
W501
4 CN501
-6.5V
1 1
L
C 2
3
AGND 2
3
B
R
MASTER 4
5
6.5V
4
5
IO
IN2
PCB ASSY 6
FGND 6 PCB ASSY
7 7
C692
5
A 10/25
W604 CN604
3
3 3 C
CONTROL VR621
2
2 2
PCB ASSY 20K B 1 1 MASTER D
PCB ASSY
1
MI C VOL
W604
CN604
W501
DDJ-WEGO2-K 9
5 6 7 8
1 2 3 4
B IO PCB ASSY
B
Connector
WALTA 14pin iPad USB signal
Control
PC USB signal IC901
USB signal switch PC or iPad USB signal
TS3USB30E
C
IC1 6.5V
DC/DC LDO LDO5V
90% 5V
IC10 -6.5V
POWER SW.
DC/DC
USB5V 90%
USB Vbus 1 2
10 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
1
MI C MASTER
3 2 AMP
L 6 AMP 7 6 7
4580 4580
1
G
3
-6.5V -6.5V
IC100
2
CON7
CN501 2
B
IC201 6.5V
1 IC200 7 6 AMP 7
4580
2 24BIT
3 DAC
vice detect(30P) 36
PCM1755 -6.5V
IC501 34
USB Controller
TUSB3200 35
38 PHONES
IC301 6.5V IC302 3.3V
1 IC300
2 24BIT
3 DAC 7 6 AMP 7 10 8
C
4580 LM4917
PCM1755 4.7 OHM
LDO5V
-6.5V
D
7
7 CN605 9
1 2 1 3 LED
DRIVER
2
E
WHEEL LED
5. DIAGNOSIS
5.1 BOOT SEQUENCE
A
START
CPU BOOT
(TUSB3200)
B
Yes
Press special or updata error ? UPDATA CODE
No
12 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
5.2 TROUBLESHOOTING
DDJ-WEGO2-K 13
5 6 7 8
1 2 3 4
14 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
[Preparations] A
Install VIRTUAL DJ LE (DJ software) on the PC. For details on installation, refer to the operation manual of the unit.
If the OS of the PC is Windows, the driver software for outputting audio from the PC must be installed beforehand.
The requirements of a PC on which VIRTUAL DJ LE can be installed are as shown below.
[Connections] C
DDJ-WEGO2-K 15
5 6 7 8
1 2 3 4
• Starting up VIRTUAL DJ LE
(Windows)
1. From the Start menu of the Windows, select All Programs, VIRTUAL DJ LE, then VirtualDJ LE (DDJ-WeGO2).
When VIRTUAL DJ LE is started for the first time, the serial number input window will be displayed.
2. After the VIRTUAL DJ LE window is displayed, click on CONFIG located in the upper left portion of the window.
B
If the Sound Setup tab is displayed on the Settings screen, VIRTUAL DJ LE does not recognize the DDJ-WeGO2.
Terminate VIRTUAL DJ LE, turn the unit OFF, then proceed from Step 3 of "Startup of the System" again.
3. Click on OK.
(Macintosh)
1. With the Finder, open the Applications folder then double-click on the VIRTUAL DJ LE icon.
(Enter the serial number in the same way as that for Windows.)
2. After the VIRTUAL DJ LE window is displayed, click on CONFIG located in the upper left portion of the window.
If the Sound Setup tab is displayed on the Settings screen, VIRTUAL DJ LE does not recognize the DDJ-WeGO2.
Terminate VIRTUAL DJ LE, turn the unit OFF, then proceed from Step 3 of "Startup of the System" again.
3. Click on OK.
C
[Loading and Playing a Track (A part)]
1. While holding the SHIFT button pressed, turn the rotary selector to select a folder or an item.
2. After releasing the SHIFT button, turn the rotary selector to select a track.
3. Press the LOAD button to load the selected track onto the deck.
4. Play the track by pressing the f button.
[Outputting Audio]
MASTER OUT OUTPUT (B part)
1. Adjust the level of the audio signal output from each deck, using the channel fader.
2. For switching the decks from which the audio signal is output, use the cross fader.
D 3. Adjust the audio level from the speakers, using the MASTER VOL control, in order to confirm that the audio signal is output
without a problem.
Rotary selector
16 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
6. SERVICE MODE
DDJ-WEGO2-K 17
5 6 7 8
1 2 3 4
6.1 FIRMWARE VERSION (MAIN UCOM) and LAST MEMORY CONFIRMATION MODE
A To enter this mode, while simultaneously holding the DECK C and DECK D buttons pressed, set the Power switch of the unit
to ON. (Hold the two buttons pressed until the opening display terminates.)
The version number of the firmware (MAIN UCOM) will be indicated with LED-lighting patterns that are switched every
2 seconds in integral part and decimal fraction part. In the blocks that are indicated with the red frames in the figures,
the number of lit LEDs indicates the corresponding number.
Confirming the Firmware Version Confirming the transmission interval (do send to
1 Integral part of the version number every any msec?) of sending MIDI IN for the jog
(LEDs on DECK C and D turn off) dial turning memorised in FlashRom.
B
X.XX
2 sec
C
2 The first place of decimal fraction part of the version number
(LED on DECK C lit)
X.XX
2 sec
3 The second place of decimal fraction part of the version number [Numerics expressed with the number of lit LEDs]
(LED on DECK D lit)
X.XX
3 ms 4 ms 5 ms 6 ms 7 ms 8 ms 9 ms 10 ms 11 ms 12 ms 13 ms
E
0 1 2 3 4 5 6 7 8 9
18 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
Apart from the firmware-version indication, the current settings of the user settable items (Color of the jog dial's illumination,
Sensitivity of the jog dial's touch sensor, and Illuminations mode) are indicated with other LEDs.
DDJ-WEGO2-K 19
5 6 7 8
1 2 3 4
In this mode, you can check if pressing each of button or turning of the jog dial is properly input and indications are also
properly displayed. The indication corresponding to a pressed button is lit only while the button is held pressed.
All the button have to be off except pressed button when all the buttons are on by Browse button.
C Part Operation Device LED display DECK
DECK C BUTTON DECK C 1
DECK D BUTTON DECK D 2
DECK A/C AUTO LOOP ENCODER JOG LED ROTATION A 1
AUTO LOOP PUSH ENCODER CTRL A 1
SYNC A/C BUTTON SYNC A/C 1
HOT CUE 1 BUTTON HOT CUE 1 1
HOT CUE 2 BUTTON HOT CUE 2 1
HOT CUE 3 BUTTON HOT CUE 3 1
HOT CUE 4 BUTTON HOT CUE 4 1
SAMPLER BUTTON SAMPLER 1
CUE BUTTON CUE 1
D PLAY/PAUSE BUTTON PLAY/PAUSE 1
TEMPO SLIDER SLIDE VOLUME FADER LED A 1
JOG ROTATION DIAL JOG LED ROTATION A 1
JOG TOUCH DIAL JOG LED ALL ON 1
CTRL A BUTTON CTRL A 1
FX 1 BUTTON FX 1 1
FX 2 BUTTON FX 2 1
FX 3 BUTTON FX 3 1
CTRL B BUTTON CTRL B 1
DECK B/D AUTO LOOP ENCODER JOG LED ROTATION B 2
AUTO LOOP PUSH ENCODER CTRL A 2
SYNC B/D BUTTON SYNC B/D 2
E HOT CUE 1 BUTTON HOT CUE 1 2
HOT CUE 2 BUTTON HOT CUE 2 2
HOT CUE 3 BUTTON HOT CUE 3 2
HOT CUE 4 BUTTON HOT CUE 4 2
SAMPLER BUTTON SAMPLER 2
SHIFT BUTTON LOOP OUT 2
CUE BUTTON CUE 2
PLAY/PAUSE BUTTON PLAY/PAUSE 2
TEMPO SLIDER SLIDE VOLUME FADER LED B 2
JOG ROTATION DIAL JOG LED ROTATION B 2
JOG TOUCH DIAL JOG LED ALL ON 2
CTRL A BUTTON CTRL A 2
F FX 1 BUTTON FX 1 2
FX 2 BUTTON FX 2 2
FX 3 BUTTON FX 3 2
CTRL B BUTTON CTRL B 2
20 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
C
[Indications by the VOL control]
The volume level is indicated in 8 steps from minimum to maximum.
Brightness will be adjusted as standard brightens. At the minimum volume, LEDs 12, 13, and 14 are lit. The lighting
LEDs shift as the volume is increased, and LEDs 3, 4, and 5 are lit at the maximum volume.
Brightness will be adjusted as standard brightens.
MIN MAX
1 1
16 2 16 2 D
15 3 15 3
14 4 14 4
13 5 13 5
12 6 12 6
11 7 11 7
10 8 10 8 E
9 9
DDJ-WEGO2-K 21
5 6 7 8
1 2 3 4
A
[Indications by the FADER control]
Indicate 10 steps as divided 10 between Min and Max. In case of Cross Fader, All the LED off is MIN, All on is
All the LED off is MIN, All on is MAX on each Deck. MAX on each Deck.
1 1
C 16 2 16 2
15 3 15 3
14 4 14 4
13 5 13 5
12 6 12 6
11 7 11 7
D
10 9 8 10 9 8
When jog dial is turned with touched jog dial platter, 3LED of jog dial turns.
1
16 2
E
15 3
14 4
13 5
12 6
11 7
10 9 8
F
22 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
This is a mode measuring jog dial rotation decline time of this unit. A
When there was designation of the rotary malfunction of the jog dial from a customer; decline for a diagnosis.
The specified range is 100 ± 40 msec.
2. How to Measure
1 You spin Jog dial more than 33*7 = 231 rpm.
*1: In case of less than 231 rpm, the controller blinks all jog dial LED at 3 times. B
blinking cycle: 1 sec
*2: You correspond both of clockwize and counter clockwize.
XXXms
2 sec
XXXms
2 sec
D
2 sec
XXXms
0 1 2 3 4 5 6 7 8 9
DDJ-WEGO2-K 23
5 6 7 8
1 2 3 4
A To enter this mode, while simultaneously holding the Sampler and HOT CUE 1 buttons on the Deck A/C side pressed,
set the Power switch of the unit to ON. (Enter this mode when opening display terminated.)
Memorize Table 1 items when enter this mode.
1. Initial Settings
1 Color of the jog dial’s illumination No color settings for any deck
2 Sensitivity of the jog dial’s touch sensor Sensitivity: 0
3 Jog dial’s MIDI message sending interval 3 msec
4 Illuminations mode Active
Table 1
B
JOG LED color is frosty white when the controller is launched after FACTORY RESET.
Table 2
ex) If Press the FX1, JOG RGB LED will be changed as below.
24 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
2. How to enter the mode for Operation Check of an iPhone/iPad Connecting Cable
While simultaneously holding the FX 3 and CTRL B buttons on the B/D deck pressed, turn the unit ON to enter this mode.
(After the opening display terminates, this mode is entered.)
3. How to Confirm
1 Properly connect the iPhone/iPad connecting cable to the DDJ-WeGO2.
Do not connect the Lightning connector of the connection cable to iOS device then.
2 Start the DDJ-WeGO2 in the mode for Operation Check of an iPhone/iPad Connecting Cable.
After the unit starts then enters this mode, the CTRL A and FX 2 buttons on the left deck are unlit. C
3 Turn the iOS device ON.
4 Connect the Lightning connector of the connecting cable to the iOS device.
Check that the CTRL A and FX 2 buttons are lit.
5 Press the CTRL B button on the right deck, and check whether a product can communicate with the authentication
chip inside the connecting cable correctly. When communication fails, "CTRL B" button flashes.
The items that can be confirmed in this mode are shown in the table below.
Operation LED indication Point to check
DECK A/C ————— CTRL A The signal from Pin 4 (ACCESSORY POWER) of the connector of the connecting
cable can be checked:
D
Lit: HIGH (An iOS device is connected.)
Unlit: LOW (No iOS device is connected, or the connected iOS device is not ON.)
————— FX 2 The signal from Pin 15 of TUSB3200 can be checked:
Lit: LOW (Communication with the iOS)
Unlit: HIGH (Communication with the PC)
DECK B/D Press the CTRL B CTRL B Whether or not communication with the Apple authentication chip inside the
button. connecting cable is established can be checked:
Lit: Communication successful
Flashing (at intervals of 1 sec): Communication failed.
DDJ-WEGO2-K 25
5 6 7 8
1 2 3 4
7. DISASSEMBLY
A Note:
Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
A B C C B C B C A
D
A -K, -R: 100-DDJLE-2952 B -K, -R: 100-DDJLE-2945 C -K, -R: 100-DDJLE-2944
-W: 100-WG2-2952 -W: 100-WG2-2945 -W: 100-WG2-2944
×5 ×3 ×10
26 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
Disassembly A
1 1 1
• Bottom view
6 1 5
3
3
1 3 1 5 CN501
4 CN604 6 5
2 2
4
MASTER PCB Assy IO PCB Assy
DDJ-WEGO2-K 27
5 6 7 8
1 2 3 4
B
• Bottom view
Wheel tooth Wheel tooth
3 3
C
• Bottom view
4 4
E (5) Remove the WHEEL (L) and (R) PCB WHEEL (L) PCB Assy WHEEL (R) PCB Assy
Assemblies by removing the six screws.
(602-SL24F-099)
5 5
5 5
5 5
28 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
Note:
When you remove CONTROL PCB Assy, it is not necessary to remove a Wheel section.
8
1 • Bottom view
5 7
DDJ-WEGO2-K 29
5 6 7 8
1 2 3 4
• Bottom view
Grease Grease
(GEM1096) (GEM1096)
• Bottom view
Cushion
C
Adhesive
(GYL1001)
Chassis Assy
D
Adhesive
(GYL1005)
IO PCB Assy
E
Sponge Sponge
30 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
• IC and PCB Assy storing firmware and user settings • Confirmation of the version of the firmware
IC600 (CONTROL IC), IC618 (MIDI IC), • Updating to the latest version of the firmware
CONTROL PCB Assy • Factory reset
• Be changed user setting to condition before the repair
(when be possible)
Procedures C
1 Hold the JOG COLOR CUE button and Power switch at the same time till all Channel level indicator turn on.
2 Click the Updater Program software, the information with 4 After upgrading and finishing automatically, the
PC. information with PC, Click "OK", finish the Firmware
3 Click "Start" to update procedure, the information with PC. update.
DDJ-WEGO2-K 31
5 6 7 8
1 2 3 4
• Illuminations mode
Pulse Mode
Active Normal
E
• Sensitivity of the jog dial’s touch sensor
-4 +4
-3 -2 -1 0 +1 +2 +3
(Low) (High)
32 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
DDJ-WEGO2-K 33
5 6 7 8
1 2 3 4
- For the applying amount of lubricants or glue, follow the instructions in this manual.
or
34 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
5 VIRTUAL DJ LE software/ • • • • • (To Be Determined) 13 Read Before Use (Important)/ See Contrast table (2)
driver software/ Quick Start Guide
operating instructions CD-ROM 14 Read Before Use (Important)/ See Contrast table (2)
6 Polyfoam L 506-WG2-658L Quick Start Guide
7 Polyfoam R 506-WG2-658R 15 Read Before Use (Important)/ See Contrast table (2)
Quick Start Guide
B
14 Read Before Use (Important)/ 502-WG2A-3329A Not used 502-WG2A-3329A Not used 502-WG2A-3329A Not used
Quick Start Guide
(Es, Pt, Ru, Ko, Ja)
15 Read Before Use (Important)/ Not used 502-WG2B-3330 Not used 502-WG2B-3330 Not used 502-WG2B-3330
Quick Start Guide (Zhcn)
DDJ-WEGO2-K 35
5 6 7 8
1 2 3 4
Decorating sheet
(NSP)
Spring
Screw (NSP)
(NSP)
A
E
B
C
C D
Cloth tape
(NSP)
Cloth tape
(NSP)
: Accessories of VR
(NSP)
Accessory
Accessory
E
-R, W model
only
F -R, W model
only
x10 SN label
(NSP)
-R, W model -R, W model Bar-code
only only (NSP)
36 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
1 CONTROL PCB Assy 704-WG2-A604 46 Anti-Dazzling Bag See Contrast table (2)
2 IO PCB Assy 704-WG2-A607 47 Clip 603-PROS2-256A A
3 MASTER PCB Assy 704-WG2-A608 48 Foot Pad 604-DDJLE-604
4 WHEEL (R) PCB Assy 704-WG2-A609 49 Stand fixing screws See Contrast table (2)
5 WHEEL (L) PCB Assy 704-WG2-A610 50 1..iPhone/iPad stand See Contrast table (2)
56 E Ring 606-DJ3000-105 B
11 2..Screw See Contrast table (2)
12 Chassis Assy See Contrast table (2) 57 Washer 606-MCD810-204
13 Spacer 612-DDJLE-447 58 Washer 606-MCD810-205
14 Sponge 612-PDJ22-428 59 Washer 606-DDJLE-260
15 Protected Cover See Contrast table (2) 60 Screw 602-M100-031
DDJ-WEGO2-K 37
5 6 7 8
1 2 3 4
45 Anti-Dazzling Bag Not used Not used 505-80DSP-239 505-80DSP-239 505-80DSP-239 505-80DSP-239
46 Anti-Dazzling Bag Not used Not used 505-80DSP-240 505-80DSP-240 505-80DSP-240 505-80DSP-240
49 Stand fixing screws 602-SWISO415-745B 602-SWISO415-745B 602-SWISO415-745B 602-SWISO415-745B 602-SWISO415-745Z 602-SWISO415-745Z
C 50 iPhone/iPad stand 701-WG2K-5403 701-WG2K-5403 701-WG2R-5403 701-WG2R-5403 701-WG2-5403 701-WG2-5403
51 Pad 604-WG2K-625 604-WG2K-625 604-WG2R-625 604-WG2R-625 604-WG2-625 604-WG2-625
38 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
DDJ-WEGO2-K 39
5 6 7 8
1 2 3 4
A D 6'
C673 0.01
A D 7'
R689 R964
L615 1K
A
B
33uH 1K 470K
R688
3
L613 C671 0.01 A_HI B_HI
VR601 R678
5
33uH R954 R955 L604 VR609 2 AD14' AD10' 2 VR613 VR620
3
C668 1K
20K B 1K 0.1 470K 100uH 20K B 20K B 2 4 6 8
5
2 470K VR619
R687 C660 TEMP 2
IC609 2 4 6 8
3 1
3 1
HP _MI X C655 0.01 1K 0.01 R957 R960 C664 0.01 C672 0.01
1 16 TEMP 1 470K 470K
7
0Y VCC A_MI D B_MI D R963 10K BX2
3 1
7
VR602 3 14 0.01 10K BX2
R952 470K R679 YCOM 1X SMAJ6.0A 20K B D669 D665 20K B
HP _VOL 2 4 13
1K 3Y XCOM RSB6.8S(NC) RSB6.8S D667
5 12
3 1
3 1
20K B C656 0.01 1Y 0X R958 C661 C665 R961 L607 SMAJ6.0A
6 11 470K 0.01 470K L606
3
INH 3X MAI N_VOL A_L OW 0.01 B_L OW 33uH
1
3
8 9 1K CHASSI S1 0.1
R953 470K GND B R620 R621 20K B 20K B 470K 20K B
2 VR603
2.2K 2.2K C669 R965 CROSSF ADER
BU4052 20K B
1
R968 C662 C666 0.01 CHASSI S
C657 FGND 0.01 R959 R962 0.01 FGND
1
51K 0.01 C645 470K 470K C646
R956 0.1 0.1
C675 C674 C678 IC611
470K IC610 1/16
0.1 AD15' AD5'1/16 PIC16F 616 C679
14 1 0.1
GND VCC 1 14
R674 13 2 VCC GND
RA0 RA5 2 13
SW IM
12 3 R672 RA5 RA0
GND
V DD
1K R611
/RST
B C676 11
RA1
RA2
RA4
RA3
4 51K 3
4
RA4 RA1
12
11
1K C680 C
C
R675 R612 1000P
1000P 10 5 R677 RA3 RA2 2.4K
RC0 RC5 5 10
9 6 RC5 RC0
4
3
2
1
2.4K RC1 RC4 6 9
8 7 51K RC4 RC1
8-8 8-7 8-6 8-8 8-7 8-6 WHEEL 1 D654
RC2
PIC16F 616
RC3 7
RC3 RC2
8 D656
EDZ CT E61 6.8B
R673 WHEEL 2 D658
EDZ CT E61 6.8B R613
R676
20K R614
1K C677 D655 20K SMAJ6.0A R60
L602 1/16 EDZ CT E61 6.8B
D657 C681 1K 1K
EDZ CT E61 6.8B L601 10K
8-5 1/16
ST C P1
ST C P1
CHASSI S1 R699
SH C P
SH C P
8-5
SO
CHASSI S2
/O E
/O E
SW IM
D660 100uH EDZ CT E61 6.8B CHASSI S1 ZD602 EMI
EDZ CT E61 6.8B ZD601 CHASSI S2 100uH
EDZ CT E61 6.8B
R887
16
15
14
13
12
11
10
16
15
14
13
12
11
10
9
R888 82
0
Q0
DS
ST C P
Q 6 SH C P
MR
V CC
OE
G N DD SO
Q0
DS
Q 5 ST C P
Q 6 SH C P
MR
V CC
OE
G N DD SO
/U RST
W4A
Q1
Q2
Q3
Q4
Q5
Q7
Q1
Q2
Q3
Q4
Q7
1
2
3
4
5
6
7
8
IC607 5 1 1 8
VCC NC CS VCC W3A
2 2 7
A SO HOL D W4B 1
4 3 3 6 300
Y GND WP SCK /CS 2
4 5 R885
GND SI SC AD5' 1K R671 AD5 3
SN74L VC1G17
R697 4
EN25F 10-100GI P AD6' AD6
C R891 R886 300 SI 1K 5
10K C682 0.1 AD7' 1K R694 AD7 0.68u(T) C604 6
W3B
R849 1.8K
R851 4.7K
R852 4.7K
R853 4.7K
R854 4.7K
R855 4.7K
R856 4.7K
R857 4.7K
R858 4.7K
R859 4.7K
R860 4.7K
R861 1.8K
D662 7
+
AD8' 1K R663 AD8
R886A RSB6.8S 8
R890 R662 AD9
750 AD9' 1K SC C605 9
750
R695 AD10 K S6 0.1 10
R885A
AD10' 1K
R1A 11
750 AD12' 1K R696 AD12 R1B 12
R3B 13
AD13' 1K R660 AD13
D 849
D 851
D 852
D 853
D 854
D 855
D 856
D 857
D 858
D 859
D 860
D 861
R3A 14
AD14' 1K R659 AD14 R2B 15
1K R2A 16
AD15' R658 AD15 AD15 17
AD14 18
AD13 19
AD12 20
ST C P2
ST C P2
ST C P2
SH C P
SH C P
SH C P
M O SI
/O E
/O E
/O E
16
15
14
13
12
11
10
16
15
14
13
12
11
10
16
15
14
13
12
11
10
9
IC606 IC605
Q0
DS
ST C P
SH C P
Q0
DS
ST C P
SH C P
Q0
DS
Q 5 ST C P
Q 6 SH C P
MR
MR
V CC
OE
V CC
OE
G N DD SO
MR
G N DD SO
V CC
OE
G N DD SO
L603
C 606
C 607
C 608
C 609
C640 C639 IC604
74595 0.1 74595 0.1 74595 D663
Q1
Q2
Q3
Q4
Q7
RSB6.8S
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q1
Q2
Q3
Q4
Q5
Q6
Q7
C638
0.01
0.01
0.01
0.01
0.1
D AG
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
A _D E C K R881
R872
R876
R878
R873
R874
R875
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
R877
R879
R880
Q841 Q843 Q845 Q833 Q835 Q837 Q825 Q827 Q829 Q831
A _Sample
C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A
R847 1.8K
R848 1.8K
1.8K
R839 560
3K
3K
R840
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
K R1 R630 6.2K
R841
R842
R843
R844
R825
R826
R845
R846
R833
R834
R835
R836
R827
R828
R837
R838
R829
R830
R831
R832
SW615
SW601 SW608 CUE- B
JFXB- A
SAMP LER- A
D601
D608 D615
1SS355
K R2 R631 1SS355 1SS
D 848
D 847
D 843
D 841
D 837
D 839
D 831
D 845
D 840
D 835
D 829
D 833
D 827
D 825
HOTCUE4- A
D602 D609 D616
ST C P1
ST C P1
ST C P1
E K R3R632 1SS355
SH C P
SH C P
SH C P
M O SI
1SS355 1SS
/O E
/O E
/O E
6.2K
SW610 SW617
SW603
HOTCUE1-
C693 HOTCUE3- A SYNC- A
16
15
14
13
12
11
10
16
15
14
13
12
11
10
16
15
14
13
12
11
10
9
ST C P
SH C P
Q0
Q0
DS
ST C P
SH C P
DS
ST C P
SH C P
MR
MR
MR
V CC
OE
SO
V CC
OE
OE
V CC
G N DD SO
G N DD SO
R698
IC602 IC603
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q1
Q2
Q3
Q4
Q5
Q6
Q7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1SS355
K R5 R6341SS355 1SS355
6.2K SW612 SW619
JFX1- A
SW605 HOTCUE3-
HOTCUE1- A
D605 D612
D619
1SS355 1SS355
R868
3.3K
K R6 R635 1SS
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
3.3K
R863
R864
R865
R867
R869
R870
Q801 Q803 Q805 Q807 Q809 Q811 Q813 Q817 Q819 Q821
R871
R824 1.8K A _Sample
C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A C114EK A
R866
PLAY- A
D606 D613 D620
R815 560
1.8K
SW621
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
3K
SW607 L619
F 33uH SAMP LER-
CUE- A
R801
R802
R803
R804
R805
R806
R807
R808
R809
R810
R811
R812
R813
R814
R817
R818
R819
R820
R821
R822
D607 D621
SW614
1SS355 1SS
DECK -A
D614
A
K S1
K S2
1SS355
D 815
D 816
D 823
D 824
D 801
D 803
D 805
D 807
D 809
D 811
D 813
D 817
D 819
D 821
40 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
R700 A
A
C673 0.01
1K R964
470K CONTROL PCB ASSY
(704-WG2-A604)
1
VR620
4 6 8
3
L605 CH_A
TEMP 2
100uH VR616 2 AD1'
20K B
3
3 1
CH_B R966
D667
VR617 2 AD0'
L607 SMAJ6.0A
20K B
3
33uH C690
2 VR618
1
CHASSI S2
470K CN605
SDA R901 33
1
L616 100uH
33 2
SCL R926 3
/INT
4
/REST
5
PMUTE
B CN605A
SW IM
6
GND
V DD
/RST
C680 CN600(NC)
CON4
L610 100uH
USBGND
7 B
1000P 8
10K R970 0(NC) USB5V
R969 9
4
3
2
1
iSCL
10K L618 iSCL 10
R903 C695 iSDA
10K 100uH iSDA 11
PM U T E
R902 10/10
EL 2
W L 1B
W L 1A
W L 2B
W L 2A
/RE ST
A 5V
D658 11P
/IN T
SD A
SC L
PW M 1
ST C P5
ST C P2
L617
SH C P
M O SI
A
B
4 SMAJ6.0A
K S2
D S1
R601 100uH
1K
10K
R699
SW IM
EMI
9-2
47/35(TL )
C627 C628 W01A W01B
C601 0.1 0.1 ADGND
4 4
80
79
78
77
76
75
74
73
72
71
70
69
68
63
62
61
67
66
65
64
AD13
/U RST
3 3
AD12
2 2
A5V
PD 4(H S)/T IM 2_C H 1(B E E P)
PD 7/T L I(T IM 1_C H 4)
PE 4
PG 7
PG 6
PG 5
PI5
PI4
PE 1(T )/I2C _SC L
PE 0(H S)/C L K _C C O
PE 3/T IM 1_B K IN
PD 1(H S)/SW IM
PD 6/U A RT 3_RX
PD 5/U A RT 3_T X
AGND 1 1
CON4 CON4
D661
1 60 K S1
NRST PI3 SMAJ6.0A
2 59 K R1
OSCI N/P A1 PI2
3 58 K R2 W02A W02B
OSCOUT/P A2 PI1
4 57 K R7 ADGND
VSSI O_1 PI0 4 4
5
VSS PG4
56 K R6
3
AD15
3
C
0.68u(T) C604 6 55 SO AD14
VCAP PG3 2 2
D662 7 54 SI A5V
+
VDD PG2 1 1
RSB6.8S 8 53 SHCP 1
VDDI O_1 PG1/CAN_RX CON4
C605 9 IC600 52 K R5 CON4
(TI M3_CH1)TI M2_CH3/P A3 PG0/CAN_TX D671
0.1 10 51 K R4 SMAJ6.0A
UART1_RX/(HS)P A4 PC7(HS)/SP I_MI SO
11 STM8S207MB 50 C698 10/25 K R3
UART1_TX/(HS)P A5 PC6(HS)/SP I_MOSI
12 49 D670
UART1_CK /(HS)P A6 VDDI O_2
13 48 C626 SMAJ6.0A
(HS)P H0 VSSI O_2 0.1
14 47 K S5
(HS)P H1 PC5(HS)/SP I_SCK
15 46 STCP 1
PH2 PC4(HS)/TI M1_CH4
(T IM 1_C H 3N )A IN 2/PB 2
(T IM 1_C H 2N )A IN 1/PB 1
(T IM 1_C H 1N )A IN 0/PB 0
16 45 STCP 6
(T IM 1_E T R)A IN 3/PB 3
AI N13/P F5 PC0/ADC_ETR
20 41 K S4
AI N12/P
TO FF4RONT P CB WN701 PE5/SP I_NSS
A IN 11/PF 3
A IN 10/PF 0
G1B
A IN 7/PB 7
A IN 6/PB 6
A IN 8/PE 7
A IN 9/PE 6
V RE F +
V RE F -
V DDA
V SSA
L614
33uH
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
iSDA
iSDA
D663 C613
CHASSI S
RSB6.8S 0.1 C691
0.01 0.01 0.01
AD9 AD9
C611
0.01
0.01
0.01
C625 C624
0.01 0.01 0.01
C629
2
2
1 C CN604
1
R1A CON3
SW634 0.01 R681
10K
2K 5 1
SW615 SW622 2
SW608 CUE- B JFXA- B 4 3 WL 1A Q602
C114EK A
JFXB- A C630 10K R690
D634 A_L OOP R682 10K
R1B 10K
D608 D615 D622 1SS355
1SS355 1SS355 1SS355 WL 1B R691
R631 C643 0.01
K SW609 SW616 SW623 0.1
JFX3- A PLAY- B DECK -B CN01A
C631 Q601
R2A 1
AGND C114EK A
D623 R683 220 2
D609 D616 SW633 0.01 10K DS1 R892
1SS355 220 3 E
355 1SS355 1SS355 5 1 STCP 5 R893
SW610 SW617
HOTCUE1- B
SW624
JFX1- B
JCUE- B
SW635 4
2
3
SHCP 1 R894 220 4
5
6
E CN01B
SYNC- A C632 R684 2SC2712GR 7
B_L OOP 10K R2B 8
D610 D617 D624 D635 D633 PWM1 R950 C892 C893 C894
R633 1SS355 1SS355 1SS355 1SS355 1SS355 0.01 1K 220P 220P 8P
SW611 SW618 SW625 SHI FT Q605
JFXA- A HOTCUE2- B SYNC- B SW636
C633 220P
R3A
D618 D625 D636 R685
D611 SW632 0.01 10K
1SS355 1SS355 1SS355 WL 2A Q603
355 1SS355 5 1 C114EK A
SW612 SW619 SW626 SW631 2 R692
JFX1- A JFXB- B JCUE- A 4 3 10K 10K
HOTCUE3- B
WL 2B R693
BROWSE C634 R686
D612 10K R3B
D619 D626 D631
5 1SS355 CN02A
635 1SS355 1SS355 1SS355 C644 0.01 Q604
SW613 SW620 SW627 SW630 D632 0.1 1
C114EK A
JFX2- A HOTCUE4- B JFX3- B LOAD- B 220 2
1SS355 DS2 R897
220 3
STCP 6 R896
636
D613
1SS355
D620
1SS355
D627
1SS355
D630
1SS355
AGND
SHCP 1 R895 220 4
5
6
D CN02B
2SC2712GR 7
L619 SW621 SW628
8
33uH SAMP LER- B JFX2- B PWM2 R951 F
C897 C895 8P
1K Q606 220P
D621 D628
SW614 220P 220P
355 1SS355 1SS355 D629
DECK -A SW629 1SS355 C896
D614
A
K S1
K S4
K S5
K S6
LOAD- A
K S2
K S3
1SS355
DDJ-WEGO2-K 41
5 6 7 8
1 2 3 4
A 4-7 2-9
4-8 4-6 1000P(X7R) C242
5-6 5-5
5-4 0.1(MLCC) C241
1/16 C240 R2
MD 5.6K_1%
MC C201 C205
ML1
R200 47/35(TL)
4-9 SCK
200 10/25
5-7 C243
16
15
14
13
12
11
10
L903
9
ZD904 ACM2012 82P
JK901i D901i
SCK
ZERO
TEST
LRCK MUTE
DATA FOMT
DGND DEEMP
VCOM
AGND
ZD903 EDZCTE61 6.8B(NC)
1 4 RSB6.8S(NC) D902i 11-1
SHELL
1 EDZCTE61 6.8B(NC) Q907i IC200
iD- RSB6.8S
2 DTC114EKA PCM1755
2 3 iD+
3 R905i
ACCESSORY POWER(8P)-1 D903i 2-6 4-3 5-1 Av=2.47dB@4.7V
WALTA CONNECTOR 14P
BCK
VCC
4 28K, 1%(NC)
OR
NC
OL
Accessory ID RSB6.8S(NC) D904i
By special cables
5
Accessory DETECT RSB6.8S ACCESSORY POWER(8P)
1
2
3
4
5
6
7
8
6
APPLE DEVICE DETECT(30P) C901i /CNG(30P) BCK R201 C20
7
5V 0.01(NC) SDO1 33 10/
8 R295
R908i 100 iKEY_SCL C902i C905i APPLE DEVICE DETECT(30P) LRCK
9 iKEY_SCL
R909i 100 iKEY_SDA 0.1(NC) 0.1 R202 33 C202 10
10 iKEY_SDA
C200
B 11 Q905i 0.1(MLCC) 330/10
12
ZD901 ZD902
S
2 R906i
10K(NC)
2-7
SHELL
13 3
14
D
EDZCTE61 6.8B EDZCTE61 G6.8B
1 R907i R615
Q901i
DTC124EKA(NC)
Q902i
DTC124EKA(NC)
4-4 2-8 4-5 5-3
10K 0(1206) C603
C906i
0.1
RTR030P02 5-2 0.1
C604
CHASSIS US USB5V Q904i 0.1
Q903i DTA114EKA(NC) C601
DTA114EKA(NC) 0.1
US C602
7-7 DGND 0.1
16
15
14
13
12
11
10
3 2 3 L500 100P C514 Text
9
3.09K,1%
SCK
ZERO
LRCK MUTE
TEST
DATA FOMT
C
AGND
DGND DEEMP
VCOM
DGND C520 R521
2-2
R515
5 10K
CHASSIS C502 C503 1000P(X7R) 2-3 IC300
52
51
50
49
48
47
46
45
44
43
42
41
40
6 2K
CHASSIS C501 10/10 0.1 PCM1755 R
PFI
CSC
DVSS
SCL
2-4
SDA
AVSS
XTI
MCLKI2
DVDDS
MCLKO
0.1 Av=2.47dB@4.7V
MCLKI
MCLLO2
1 39
BCK
VCC
PFO /CRST 15.4
OR
NC
OL
2 38 R511 200 SDO2
F500 11-2 3
AVDD CDATI
37 C306
1
2
3
4
5
6
7
8
U/OE PWMO DVDD
1.5A/63V U/OE 3.3V-1 4 36 R510 200 SDO1 BCK R302 10/25
PLLO CDATO
ZD500 IC901i R501 1.5K 5 35 R509 200 LRCK SDO2 33
C903i C904i DVSS CSYNC
1 10 6 34 R508 200 BCK LRCK R395
EDZCTE61 6.8B S VCC 0.1 10/10(NC) R502 22 PUR IC501 CSCLK
2 9 7 33 C523 R303 33 A5V
D1+ /OE DP DVSS
C5271000P
C5250.47(M)
3
4
D2+ D1-
8
7
R503 22 8
9
DM
TUSB3200
P17
32
31
C511
0.1 1000P(X7R) 7-5 6-5 2-12 10K R608 C302
10
C303
D+ D2- DVDD P16 0.1(MLCC) 330/10
5 6 SMAJ6.0A 10 30 ACCESSORY POWER(8P) R525 200MD 10K R529
GND D- /MRST P15
D505 11 29 R526 200MC 10K R530
11-4 TS3USB30E 12
TEST
EXTEN
P14
P13
28 R527 200
ML1 10K R531 2-13 6-6 7-6
PLLOEN
P33
P34
P35
P10
P11
P12
US 1000P(X7R)
0.1 I O
11-4
14
15
16
17
18
19
20
21
22
23
24
25
26
COM
C507
R504 R612 10K 0.1 R528 200ML2 10K R532
100 U/OE C508 /CNG(30P) 10K R609(NC) C63
U/OE C61
US R507 0.1 APPLE DEVICE DETECT(30P) 10K R610(NC) 0.1 22/25
US
10K C522 C64
R611 10K 1000P(X7R) 0.1
D506 Q
D R522 /INT
G
C12
SMAJ6.0A 100
/REST
D5V
L62
R85
CHASSIS DGND 0(1206) C3 220/10
BEAD(600ohm)
D7
1SS355T Q6
D6 C2
A124TKA
1SS355T D2
USBGND
1SS355T 0.22(NC)
R3 1K R4
USB5V 100K
D3 -6.5V
L63
IC3 1SS355
3
R2 Q7 BEAD(600ohm)
Q10 3 4
D
GND VO A114TKA
R5
RTR030P02 2 D4
0
G
S
0 SUB
1 5 1SS355
2
NC VCC C605
R1
C4 47/10(NC)
3K ZD1 BD4740G
1
47/10 R10
C1 TFZ 3.3B(NC) C18 0.22
47K U
D1 0.1
2
SMBJ9.0CA SW01
POWER
E R657
L4
SM5819A 0(NC)
6.8uH L1
6.5V
D5 BEAD(65 OHM)
8
7
6
5
TPS61085 L3
C5 1-4 8-4
SS
IN
SW
FREQ
GND
18K
EN
FB
C12 10/25
C65 4.7uF/16
22uH/1.11A R8 3 4
1
2
3
4
TPS54232 R74
48.7K 1% C66
C74
C75
C72 R72 270P
0.015u 6.2K 12P R658
R73
0(NC)
47K L2
F C77
-6.5V
4.7/25 BEAD(65 OHM)
B
42 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
Av=8.79dB C209
C253
10/25 4-1 B IO PCB ASSY A
00P(X7R) C242
C207
0.1
5
6.5V
IC201B
4-10 5-8 (704-WG2-A607)
8
1(MLCC) C241 470P/NC 7
R205 4580
6
1/16 C240 R203 L201
4
12K_1% C210
5.6K_1% BEAD(100ohm)
C201 C205 0.1 -6.5V
C254 4-2 1-3 8-2
47/35(TL) C211 10/25
10/25
R293 82P L203
R207 -6.5V CN501
10K BEAD(600ohm)
5-9
11
10
C251 15.4K_1% 1
9
820P 2
ZERO
VCOM
AGND
L205
3
C252
820P
R294
C208
470P/NC 3
IC201A
1
BEAD(600ohm)
L204
4
5
6
C W501
VCC
6.5V BEAD(600ohm)
4580
5-9
OR
R206
OL
10K 2 7
1
6
7
8
1
2
3
4
5
6
7
1
C307 330 7-3 6-3 D2704K(NC) G
CP-
R653
CP+
PGND
0
SD_LC
CPOUT
CPVDD
20.5K_1%
-AVDD
47/35(TL) Q207
R253 330(NC) 0(NC) C368 C367 PHONES
L305 IC302 820P 820P
11
10
R3341000P(NPO) R332
ZERO
6-3 7-3
AGND
VCOM
470P/NC
ROUT
AVDD
LOUT
1 R336 L
RIN
G
9
8 Q208
VCC
C306
C316
82P C366 100K
100uH/0.2A C331 C332 7-12 PHONES
6
7
8
-6 7-6
IC6 R652 L61 Av=-1.157dB
0(NC) BEAD(600ohm)
m) BA05FP
I O
COM
C61 C63
0.1 22/25
C64
0.1
Q21
G
C124TKA D
D5V
L62
BEAD(600ohm)
SDA
1
2
SCL
3
/INT
4
/REST
L63
PMUTE
D5V
5
6
7
A
BEAD(600ohm)
USB5V
8
9
CN605
iKEY_SCL
iKEY_SCL 10
C605 iKEY_SDA
iKEY_SDA 11
47/10(NC)
CN605A
USBGND 11P
B
DDJ-WEGO2-K 43
5 6 7 8
1 2 3 4
R213
20.5K _1%
20.5K _1% R284 82P C219
C79
B C213 R211 10/16
C217
6.5V 3-3
8
20.5K _1% 0.1 4-1
4.7/50
5 IC202B
R297 4-
7
100K 4580
6
W501 -6.5V C227 C218 3-4 4-2
4.7/25 -6.5V
4
1 0.1
2
C78
C
3 10/16
B CN501 4 C228
C214 R296 R212 3 IC202A
5 4-
4.7/25 4.7/50 100K 20.5K _1% 1
6 4580
2
7 6.5V
CON7 FGND C220
R285
82P
20.5K _1% R214
C113 20.5K _1%
150P
D
R109
C115
3-3 6.5V
8
10/25 0.13
1 0.1 5
4580
2 2 R108 71 CN604
4580
3-4 C112 1.8K 6
3
-6.5V 3-4 C110 2
4
R110
-6.5V 1
4
E 20K 0.1
IC101A 0.1 CON3
IC100B MI C VO
C
44 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
3
5K _1%
C219
C79 B
10/16
6.5V 3-3
4-1 3-2
IC202B C223 R217 Q201 R219 Q205
7 4-10 5-8 10/25 D2704K 91 D2704K
80 91 C225 JK 102
470P
3-4 4-2 R215 R221 R251 3 L
M A ST E R O U T
-6.5V 100K 1.2K 1.2K
AGND 1
C78
10/16 R216 R222 R252 C226 2 C
100K R
IC202A 1.2K 1.2K 470P
4-10 5-8
1
80
Q206
C224 R218 Q202 R220
10/25 D2704K
C220 91 D2704K 91
82P
14
0.5K _1%
TO CONTROL PCB
4.7uF /63V(L ) L63 3-1
D
C
DDJ-WEGO2-K 45
5 6 7 8
F
E
B
A
D
C
46
D
D 677 1K R942 A 1R
D 676 1K R941 A 2R
A
CN02A
D 675 C omment:
R9401K A 3R
1
1
8
7
6
5
4
3
2
1
D682
CN02B
D683
R R928 A 4R
A
Com ment: 8P
D681
510
LEDRGBGG
K G R929 A 5R
+ B
510
5V
DS2
IC615
DGND
WL 2B
WL 2A
D642
R930 STCP 6
B A 6R 1 16 SHCP 1
D640
C Q1 V CC
510 2 15
Q2 Q0
3 14 D S2
D639
Q3 DS
(704-WG2-A609)
4 13
74595
Q4 OE
5 12 ST C P6
R939 Q 5 ST C P
WL 2B
WL 2A
D 674 1K A 7R 6 11 SH C P1
Q 6 SH C P
7 10
Q7 MR
R938 8 9
D 673 1K A 8R G N DD SO
D WHEEL (R) PCB ASSY
R981
D 672 1K R937 B 1R
100K
R992
0.1
D680
D672
2.2/16
C904
C992
51K
2
2
R925
D651
R B 2R
A
510
LEDRGBGG
LTH- 301-07
K G R990 B 3R
+ B
510
1K
R982
B R927 B 4R
D639
C
510
D673
IC616
D 683 1K R948 B 5R
10.4 WHELL (R) and (L) PCB ASSYS
1 16
D679
Q1 V CC
R947 2 15
D 682 1K B 6R Q2 Q0
3 14
Q3 DS
R946 4 13
74595
D 681 1K B 7R Q4 OE
5 12 ST C P6
Q 5 ST C P
6 11 SH C P1
51K
Q 6 SH C P
R983
7 10
DDJ-WEGO2-K
R934 Q7 MR
R B 8R 8 9
A G N DD SO
510
LEDRGBGG
K G R935 C 1R
D652
+ B
D674
510
0.1
R936
LTH- 301-07
3
B C 2R
3
C905
D678
D642
C
510
1K
R984
D 680 1K R945 C 3R
IC617
D 679 1K R944 C 4R
D640
1 16
R943 Q1 V CC
D 678 1K C 5R 2 15
Q2 Q0
3 14
Q3 DS
4 13
Q4 OE
74595
D641
5 12 ST C P6
R931 Q 5 ST C P
R C 6R 6 11 SH C P1
A Q 6 SH C P
510 7 10
LEDRGBGG
Q7 MR
8 9
D675
R932 G N DD SO
K G C 7R
+ B
510
D677
B R933 C 8R
D641
D676
510
0.1
C906
4
4
5
5
E
A
CN01A
D670
D 663 1K R916 A 1L
8
7
6
5
4
3
2
1
D669
CN01B
D 664 1K R917 A 2L
D671
D 665 1K R918 A 3L
Com ment: 8P
R R907 A 4L
D635
A
510
5V
LEDRGBGG
DS1
IC612
DGND
WL 1B
WL 1A
R908
STCP 5
SHCP 1
K G A 5L 1 16
D638
+ B Q1 V CC
510 2 15
Q2 Q0
3 14 D S1
R909 Q3 DS
B A 6L 4 13
74595
D637
C Q4 OE
(704-WG2-A610)
510 5 12 ST C P5
Q 5 ST C P
6
WL 1B
WL 1A
6
6 11 SH C P1
Q 6 SH C P
7 10
Q7 MR
R919 8 9
D 666 1K A 7L G N DD SO
WHEEL (L) PCB ASSY
R920
D660
D668
D 667 1K A 8L
R985
0.1
2.2/16
C901
C991
R921
100K
R991
D 668 1K B 1L
51K
D653
R R910 B 2L
A
LTH- 301-07
510
LEDRGBGG
K G R911 B 3L
1K
+ B
510
R986
D667
B R912 B 4L
D638
DDJ-WEGO2-K
C
510
D661
IC613
1 16
Q1 V CC
R922 2 15
D 669 1K B 5L Q2 Q0
3 14
Q3 DS
4 13
74595
R923 Q4 OE
7
D 670 1K B 6L 5 12 ST C P5
7
Q 5 ST C P
6 11 SH C P1
R924 Q 6 SH C P
R687
51K
D 671 1K B 7L 7 10
Q7 MR
8 9
G N DD SO
LEDRGBGG
0.1
D662
C902
K G R988 510 C 1L
LTH- 301-07
+ B
R989
1K
B 510 C 2L
D645
C
R688
D637
IC614
D 660 R913 1K C 3L
1 16
R914 Q1 V CC
D 661 1K C 4L 2 15
Q2 Q0
D636
3 14
R915 Q3 DS
D 662 1K C 5L 4 13
Q4 OE
74595
5 12 ST C P5
Q 5 ST C P
6 11 SH C P1
D665
Q 6 SH C P
7 10
Q7 MR
R904 8 9
R 510 C 6L G N DD SO
A
8
8
D663
LEDRGBGG
D664
K G R905 510 C 7L
+ B
0.1
C903
B R906 510 C 8L
D646
E
47
F
E
B
A
D
C
1 2 3 4
10.5 WAVEFORMS
1-1 5 V (JK501 Pin 1) 2-2 CDATI (IC501 Pin 38) 2-7 SDO1 (IC200 Pin 2) 2-12 SDO1 (IC300 Pin 2)
1-2 6.5 V (CN501 Pin 5) 2-3 CDATO (IC501 Pin 36) 2-8 LRCK (IC200 Pin 3) 2-13 LRCK (IC300 Pin 3)
1-3 -6.5 V (CN501 Pin 1) 2-4 CSYNC (IC501 Pin 35) 2-9 SCK (IC200 Pin 16) 2-14 IC315 ADC -> Pin 11 (BCK)
1-4 3.3 V (C17) 2-5 CSCLK (IC501 Pin 34) 2-10 SCK (IC300 Pin 16) 3-1 INPUT (JK101)
2-1 MCLKO (IC501 Pin 44) 2-6 BCK (IC200 Pin 1) 2-11 BCK (IC300 Pin 1) 3-2 MASTER OUT (JK102)
48 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
3-3 6.5 V (IC100/101/202 Pin 8) 4-4 SDO1 (IC200 Pin 2) 4-9 ML1 (IC200 Pin 15) 5-4 SCK (IC200 Pin 16)
3-4 -6.5 V (IC100/101/202 Pin 4) 4-5 LRCK (IC200 Pin 3) 4-10 (IC201/202 Pins 7/1) 5-5 MD (IC200 Pin 13)
4-1 6.5 V (IC201/202 Pin 8) 4-6 SCK (IC200 Pin 16) 5-1 BCK (IC200 Pin 1) 5-6 MC (IC200 Pin 14)
4-2 -6.5 V (IC201/202 Pin 4) 4-7 MD (IC200 Pin 13) 5-2 SDO1 (IC200 Pin 2) 5-7 ML1 (IC200 Pin 15)
4-3 BCK (IC200 Pin 1) 4-8 MC (IC200 Pin 14) 5-3 LRCK (IC200 Pin 3) 5-8 (IC201/202 Pins 7/1)
DDJ-WEGO2-K 49
5 6 7 8
1 2 3 4
5-9 R/L Channel (CN501 Pins 2, 4) 6-5 SDO1 (IC300 Pin 2) 6-10 ML2 (IC300 Pin 15) 7-4 BCK (IC300 Pin 1)
6-1 6.5 V (IC301 Pin 8) 6-6 LRCK (IC300 Pin 3) 6-11 (IC302 Pin 8) 7-5 SDO1 (IC300 Pin 2)
6-2 -6.5 V (IC301 Pin 4) 6-7 SCK (IC300 Pin 16) 7-1 6.5 V (IC301 Pin 8) 7-6 LRCK (IC300 Pin 3)
6-3 3.3 V (IC302 Pins 2/9 ) 6-8 MD (IC300 Pin 13) 7-2 -6.5 V (IC301 Pin 4) 7-7 SCK (IC300 Pin 16)
6-4 BCK (IC300 Pin 1) 6-9 MC (IC300 Pin 14) 7-3 3.3 V (IC302 Pins 2/9) 7-8 MD (IC300 Pin 13)
50 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
7-9 MC (IC300 Pin 14) 8-2 6.5 V (CN501 Pin 5) 8-7 STCP (IC607/608 Pin 12) 11-1 (Q907i Collector)
7-10 ML2 (IC300 Pin 15) 8-3 -6.5 V (CN501 Pin 1) 8-8 OE (IC607/608 Pin 13) 11-2 (IC901i Pin 1)
7-11 (IC302 Pin 8) 8-4 3.3 V (C17) 9-1 VR Voltage 11-3 (IC901i Pin 9)
7-12 R/L (JK301/302) 8-5 5 V (IC607/608 Pin 16) 9-2 SDA (IC600 Pin 68) 11-4 (IC901i Pin 2 (D+) & Pin 8 (D-))
8-1 5 V (JK501 Pin 1) 8-6 SHCP (IC607/608 Pin 11) 10-1 POWER ON SDA
DDJ-WEGO2-K 51
5 6 7 8
1 2 3 4
A
52 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
A
SIDE A
C CN604
W604
SIDE B
A
D
CN02A
CN02B
D
A
54 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
SIDE B
A
B CN605A
9-2 CN605
E
CN01A
CN01B
D
A
DDJ-WEGO2-K 55
5 6 7 8
1 2 3 4
B IO PCB ASSY
1-1
8-1
7-12
7-12
A CN605
SIDE B CN605A
D B IO PCB ASSY
8-3 8-2
IC1
5-9 1-3 1-2
Q901i-Q904i
CN501
C W501 IC10
Q7 IC501
Q21
Q6
IC300
C
IC302
2-2 2-4 2-5 2-3 2-10 2-11 2-12 2-13 6-8 6-9 6-10
6-7 6-4 6-5 6-6 7-8 7-9 7-10
7-7 7-4 7-5 7-6
SIDE B
D
Q207
Q203
Q208
Q204
6-2 7-2
IC6
Q211 IC301
6-1 7-1
Q210
IC3
E
4-2
4-10 5-8
Q10
CN501
IC201
IC2
Q905i Q907i
4-10 4-1
5-8
IC901i F
11-1 B
DDJ-WEGO2-K 57
5 6 7 8
1 2 3 4
B
W501
CN501
B
A
CN604
W604
3-1
SIDE B SIDE B
C MASTER PCB ASSY
3-3 3-4 3-3 3-4
IC100
IC101
CN604
E
W501
Q202
Q206
IC202
Q205
Q201
58 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
IC616
CN02B
B
A CN02A
IC617 IC615
SIDE B SIDE B
D WHEEL (R) PCB ASSY
D
CN02B
D
DDJ-WEGO2-K 59
5 6 7 8
1 2 3 4
IC613
B
IC614
A CN01A
CN01B
IC612
SIDE B SIDE B
E WHEEL (L) PCB ASSY
D
CN01B
E
60 DDJ-WEGO2-K
1 2 3 4
5 6 7 8
- Although the cables that are directly mounted on each PCB Assy are listed individually as electrical parts of the
corresponding PCB Assy in the parts list, those cables are included with each PCB Assy for service when it is supplied.
Mark No. Description Part No. Mark No. Description Part No.
VR 616,617 418-PDJ33-672
LIST OF ASSEMBLIES VR 602,603,621 418-SINN7-606
CONTROL PCB ASSY 704-WG2-A604
IO PCB ASSY 704-WG2-A607 R 885,886,889 412-900-975
MASTER PCB ASSY 704-WG2-A608
R 801-814,817-822,825-838,841-846 412-900-994
WHEEL (R) PCB ASSY 704-WG2-A609
R 620,621 412-3113-048 B
WHEEL (L) PCB ASSY 704-WG2-A610 R 892-897 412-3113-058L
R 614,676 412-3113-078
R 631-635 412-HV3363K-349
CAPACITORS
Mark No. Description Part No. C 644 413-3113-035
Q 817,819,821,825,827,829,831,833,835 416-HDJ2460-234
Q 837,841,843,845
D 601-636
ZD 603
416-HDJ2460-234
414-CD1000-075A
414-DDJLE-332
B IO PCB ASSY
SEMICONDUCTORS
D 662-665 414-DJ1100G-207 > IC 1 417-200USB-1071
IC 3 417-9000-740
D 601,602,654-657,660 414-RMP3-285 IC 302 417-DDJLE-1079
D 658,661,666,667,670,671 414-UDJ200-284 IC 200,300 417-HP400U-995
D 801,803,805,807,809,811,813,816,817 410-DJ5000-253T > IC 10 417-PDJ33-1045
D
D 819,821,823-825,827 410-DJ5000-253T
D 829,831,833,835,837,840,841,843,845 410-DJ5000-253T IC 201,301 417-ST150-599
> IC 6 417-U101-497
D 847,848,849,851-861 410-DJ5000-253T Q 203,204 416-3000-378
D 815,839 410-HDJ2000-162T Q 21 416-DFX1-201
Q 907i 416-HDJ2460-234
MISCELLANEOUS
SW632-634 ENCODER 403-DDJLE-418 Q 6 416-HDJ9700-210
W01A TO 01B,W02A TO W02B WIRE HARNESS 404-DDJLE-3721 Q 7 416-S300-327
604 WIRE HARNESS 404-DDJLE-3722 Q 10,905i 416-UDJ200-347
CN 01A,02A CONNECTOR 404-PDJ33-3584 D 5,50 414-007USB-148
CHASSIS 1 WIRE 406-DDJLE-1229 D 2,3,4,6,7 414-CD1000-075A
E
CHASSIS 2 TO G5 1P WIRE 406-M207-1028 D 1 414-DDJLE-348
W3A TO W3B WIRE 406-DDJLE-1237 D 902i,904i 414-DJ1100G-207
W4A TO W4B WIRE 406-H464-020 ZD 500,901,902 414-RMP3-285
G1A TO G1B WIRE 406-MX200-1110 D 505,506 414-UDJ200-284
IS/ISA/AG\TO IS/ISA 3P-2P LEAD WIRE 406-WG2-1262
MISCELLANEOUS
L 601-605,610,616-618 COIL 415-HT8015-040 JK 302 JACK GROUND PLATE 300-300-1171
L 607,613-615,619 MICRO INDUCTOR 415-RCC955A-094 JK 501 USB GROUND PLATE 300-DDJLE-2071
L 606 INDUCTOR 415-HMD5000-097 JK 901 FIXED PLATE 300-WG2-2103
SW606,607,615,616 TACT SW 403-DDJLE-416 SW01 SLIDE SW 403-DV300-5007
SW601-605,608-614,617-631,635,636 SWITCH 403-MC2-383 CN 501 7P SOCKET 404-HMD5000-785A
DDJ-WEGO2-K 61
5 6 7 8
1 2 3 4
Mark No. Description Part No. Mark No. Description Part No.
JK 901i USB CONNECTOR 420-WG2-385
A
X 500 CRYSTAL (6 MHz)
CN 605A 11P 1.0 FFC SOCKET
L 35,61-64,203-205,305,500 CHIP BEAD
427-S1-143
404-500C-3711
415-1300-240A
D WHEEL (R) PCB ASSY
SEMICONDUCTORS
L 4 INDUCTOR 415-DDJLE-407 IC 615-617 417-DDJLE-1080
L 902,903 COMMON MODE FILTERS 415-FU800-305 D 651,652 417-HDJ2000-411
CAPACITORS CAPACITORS
C 343 413-MC6000-1191 C 901-903 413-DCM280-773
C 201,301 413-MEP4-1245
C 991 413-U5000-1005
C C 1,6,61,64,71,73,209,210,313,314,501 413-DCM280-773
C 503,504,506-508,511,512,514,601-604 413-DCM280-773
C 5903i,905i,906i 413-DCM280-773
C 8,17,70,76,322 413-MC6000-1180
C 319,321 413-U5000-1005
C 200,303 413-007USB-828
C 527 413-1430-071
C 4 413-810-920
C 202,241,302,341 413-900-835
C 63 413-CDMIX2-631
C 317,366 413-DV300-5156
D C 3 413-HT801K-192
C 525 413-QSPAND-632
C 205,206,253,254,305,306,311,312 413-SPPW3-235
MISCELLANEOUS
E JK 101 JACK GROUND PLATE 300-300-1171
JK 102 GROUND PLATE 300-33-1917
FIXED PLATE 300-4500-2010A
CN 604 3P SOCKET 404-HP1010K-259A
JK 102 2P RCA JACK 420-100U-256
CAPACITORS
C 103 413-SP2U-1136
C 109-112,118,217,218 413-DCM280-773
C 78,79 413-DV300-5155
F
C 213,214 413-HT801K-191
C 115,223,224 413-SPPW3-235
C 104 413-SPPW3-236
62 DDJ-WEGO2-K
1 2 3 4