Professional Documents
Culture Documents
051- 2113744
CAPITAL BUILDERS 2113549
Flat No. 14, Ground Floor, Abu Dhabi 2764612
Tower, F-11 Markaz, Islamabad Fax #. 051-2101151
E.mail.capitalbuilders@ymail.com
PURCHASE ORDER
Ref: SR No. PO No. CB/PO/2019/536
Date: Date: 28-09-2019
1. Payment Terms.
a. 50 % Advance along with purchase order.
b. 25% at inspection.
c. 25% after successfully installation.
2. The supplier shall provide WHT exemption certificate otherwise taxes will be
deducted as per law of the land.
3. The supplier will open LC fulfilling all the requirements and will also make
payment to the principal in Foreign exchange at his own end,
4. Above dimensions is tentative. The supplier shall submit as per site shop
drawings for approval.
5. The supplier is responsible for two year free maintenance from date of taking
over.
6. The supplier shall warranty for the material and equipment provided through this
contract to be new of good workmanship and shall be free from any defects. If
within (24) calendar months from the date of physical completion/ taken over by
the engineer-in-charge any component of equipment provided is found to be
defective in workmanship or quality. The supplier shall replace/ repair the same
to the entire satisfaction of Engineer-in-charge at his own expense immediately
but not later than the period fixed by the Engineer-in-charge failing which
necessary repair/replacement of the item will be carried out at supplier’s risk and
cost and expenditure will be recovered from the supplier
7. The Supplier shall be bound to train the MES/Factory Staff BPS-06 to 11 for
operation/maintenance of equipment.
8. Original Invoice, Delivery Letter, Bills and Warranty Certificate of the
manufacturer to prove the genuineness of the metrical/equipment will be
provided by the supplier.
9. The supplier shall be responsible and fulfill all the technical requirement of our
client MES.
10. In case of substandard material the seller is under obligation to replace at his
own
11. Job completion tile is 8-10 weeks.
Thanking you
Sign: __________________.
Name: __________________
NIC No. _________________
MUHAMMAD IQBAL
Chief Executive
Dist:
Accounts P.O File Supplier
IMPORTED SCOPE OF SUPPLY
Annexure-A
HOISTING GROUP
Capacity ton 5
Type BVS-01-M41
Hoisting Reducer 1 Unit Single input shaft, single output shaft,(ABM, GERMANY)
Hoisting Speed m/min 4,0/0,66
Hoisting Motor kw-rpm 4.9/0.8-3000 % 40 ED (ABM, GERMANY)
Inverter Power of Hoisting Motor kw Double Speed Motor
Hoisting Brake kgm Electromagnetic Disc Brake
Rope Diameter mm 10(18x7 200kg/mm2, steel core rope)
Rope Reeving m/min 4/1
Hook Type kw-rpm DIN 15401 (Single Type with safety Lanch, Forged steel)
Trolley Travelling Speed m/min 20/5
Trolley Travelling Motor Kw-rpm 1x0.55-1500(WAT) % 40 ED
Inverter Power of Trolly Travel Motor Kw 0.55 (TELEMECANIQUE,ABB)
Trolley Travelling Brake Kgm Electromagnetic Dic Brake
Trolley Travelling Reducer 2 Unit Reducer with Holed Shaft
Trolley Travelling Drive System Direct Drive
Trolley wheel Diameter mm 125 (4 Units of wheels/2 Direct Drive -2 Idle)
ELECTRICAL INSTALLATION
Supply Voltage and Frequency Volt-HZ 400-50
Trolley Festoon Line
Control voltage and Protection class Volt 48-IP65 with Push Button (Free from trolley with cable)/
Telemecanique
Control Type REMOTE CONTROL
Witch Material of Control Panel SIEMENS or TELEMECANIQUE
Control Panel Trolley Control Panel (Hoisting Klemens layout)
Bridge Control Panel (Trolley and Bridge Travelling
Inverters)
Cable Rubber- H07RNF/Untel
Emergency stop in control panel Warning system with horn and light
SAFETY EQUIPMENT Phase and thermal protection Bridge and trolley limit switch overload
relays limit switches for hoisting limit switch.
SAFETY EQUIPMENT:
Annexure-B
Main bridge of double girder box construction type suitable for 52.66M span as per manufacturing
design from BVS will be painted with Matt finish three coats of Enamel Yellow paint after
application of red oxide primer.
For the supply and fixing of 2x125 M Billet. Suitable for 52.66 M span.
Buyer: Supplier: