Professional Documents
Culture Documents
Index
Particulars Page No.
Index
Particulars Page No.
PIX-PowerWare® Couplings
PIX-Tyre & Tyre-spacer Couplings 68-74
PIX-Gear Couplings 75-79
PIX-Star / Jaw Couplings 80-83
PIX-Standard Star / Jaw couplings 84-85
PIX-HRC Couplings 86-91
PIX-Pin Bush Couplings 92-97
PIX-Resilient / Grid Couplings (Z-Type) 98-102
Notes 103
- PowerWare®
To fulfill its commitment of providing a complete “Power Transmission Solution” to its users, the
company has also added PIX-PowerWare® Pulleys and PIX-PowerWare® Couplings to its range of V-
Belts.
The introduction of PowerWare® products in the range would facilitate the users to achieve optimum
power transmission from drives consisting of PIX-PowerWare® Pulley with the matched PIX V-Belt. It
will also help users in getting a complete power transmission solution comprising of Pulleys, Couplings
and Belts from the same manufacturer thus eliminating the chances of mismatch.
PIX-PowerWare® Pulleys and Couplings are made as per international standards and follow a strict
manufacturing procedure in accordance with the ISO standards.
This technical catalogue features a technical know-how about Pulleys, Bush and Couplings.
About Pulleys
A Pulley is also called a sheave or drum and may have a
groove between the two flanges around its circumference.
The drive element of a Pulley system can be a rope, cable,
Set screw
Belt, or chain; that runs over the Pulley inside the groove.
Integral key
A Belt and Pulley system is characterised by two or more
Pulleys in common to a Belt. This allows for mechanical
power, torque, and speed to be transmitted across the
axles. If the Pulleys are of differing diameters, a mechanical
advantage is realised.
Bush
A Belt drive is analogous to that of a chain drive, however a V-Belt grooves
Belt sheave may be smooth (devoid of discrete interlocking
members as would be found on a chain sprocket, spur gear,
or timing Belt) so that the mechanical advantage is
approximately given by the ratio of the pitch diameter of the
sheaves only, not fixed exactly by the ratio of teeth as with
gears and sprockets.
Pulley codification
V-Pulleys Poly-V Pulleys Timing Pulleys
SSS 0000 00 0000 XXX SS 0000 00 0000 XXX 000 SSS 00 0000 XXX
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
1
- PowerWare®
PIX-PowerWare® Pulleys
Poly-V Pulleys
2
- PowerWare®
Pulley schematic representation
Timing Pulleys
3
- PowerWare®
Standard V-Belt Pulley groove details
Min. groove
Groove Min. distance Centre to Edge of pulley Groove Min.
depth Pitch
Pitch from outside below pitch centre of to 1st groove top width
Section diameter to groove centre diameter angle
Width diameter of groove
Pitch Dia. (See note 2) (See note 3) (dp) mm (? )mm
(Wp) mm (B) mm (Note 4) (g) mm
(e) mm (f) mm
(h) mm
Z, SPZ 8.5 2.00 9.0 12±0.3 8.0±1.0 Up to 80 34±0.5 9.7
ZX, XPZ Over 80 38±0.5 9.9
LL
ff e
g
Wp
b
hh
Outside dp
è
diameter
1. The tolerance on the dimensions apply to the distance between the center of any two grooves
whether adjacent or not
2. It is recommended that the tolerance on dimensions should be taken into account while aligning the
Pulleys
3. When the Pulleys are to be used for V-Belts Z, A, B, C sections, the value of 'h' may be reduced by 20%
4. Only above dimension Pulleys should be used for Banded Belts except for 'A' section, where e=15.9
mm
4
- PowerWare®
Z / ZX & SPZ / XPZ section Pulleys
F F F F F F F
PD PD PD PD PD
PD PD
OD OD OD OD OD OD OD
M L M K L M K M K L M K L K L M
L L
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
(PD) (OD)
of
Metric Imperial
F K L M Type
Code grooves Number
(mm) (mm) (mm) (Inches)
Z 0067 01 1 1108 28 1 1/8'' 16 - 23 7 1
67 71
Z 0067 02 2 1108 28 1 1/8'' 28 5 23 - 6
Z 0071 01 1 1108 28 1 1/8'' 16 - 23 7 1
71 75
Z 0071 02 2 1108 28 1 1/8'' 28 5 23 - 6
Z 0075 01 1 1108 28 1 1/8'' 16 - 23 7 1
75 79
Z 0075 02 2 1210 32 1 1/4'' 28 3 25 - 6
Z 0080 01 1 1210 32 1 1/4'' 16 - 26 10 1
Z 0080 02 80 84 2 1210 32 1 1/4'' 28 3 25 - 6
Z 0080 03 3 1210 32 1 1/4'' 40 14 26 - 6
Z 0085 01 1 1210 32 1 1/4'' 16 - 26 10 1
Z 0085 02 2 1610 42 1 5/8'' 28 3 25 - 6
85 89
Z 0085 03 3 1610 42 1 5/8'' 40 14 26 - 6
Z 0085 04 4 1610 42 1 5/8'' 52 26 26 - 6
Z 0090 01 1 1210 32 1 1/4'' 16 - 26 10 1
Z 0090 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0090 03 90 94 3 1610 42 1 5/8'' 40 14 26 - 6
Z 0090 04 4 1610 42 1 5/8'' 52 26 26 - 6
Z 0090 05 5 1610 42 1 5/8'' 64 38 26 - 6
Z 0095 01 1 1210 32 1 1/4'' 16 - 26 10 1
Z 0095 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0095 03 95 99 3 1610 42 1 5/8'' 40 14 26 - 6
Z 0095 04 4 1610 42 1 5/8'' 52 26 26 - 6
Z 0095 05 5 1610 42 1 5/8'' 64 38 26 - 6
Z 0100 01 1 1210 32 1 1/4'' 16 - 26 10 1
Z 0100 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0100 03 100 104 3 1610 42 1 5/8'' 40 14 26 - 6
Z 0100 04 4 2012 50 2'' 52 26 26 - 6
Z 0100 05 5 2012 50 2'' 64 31 33 - 6
Z 0112 01 1 1610 42 1 5/8'' 16 - 26 10 1
Z 0112 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0112 03 112 116 3 2012 50 2'' 40 7 33 - 6
Z 0112 04 4 2012 50 2'' 52 19 33 - 6
Z 0112 05 5 2012 50 2'' 64 31 33 - 6
Z 0125 01 1 1610 42 1 5/8'' 16 - 26 10 1
Z 0125 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0125 03 125 129 3 2012 50 2'' 40 7 33 - 6
Z 0125 04 4 2012 50 2'' 52 19 33 - 6
Z 0125 05 5 2517 60 2 1/2'' 64 18 46 - 6
5
- PowerWare®
Z / ZX & SPZ / XPZ section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
(PD) (OD)
of
Metric Imperial
F K L M Type
Code grooves Number
(mm) (mm) (mm) (Inches)
Z 0140 01 1 1610 42 1 5/8'' 16 - 26 10 1
Z 0140 02 2 1610 42 1 5/8'' 28 3 25 - 6
Z 0140 03 140 144 3 2012 50 2'' 40 - 33 7 2
Z 0140 04 4 2012 50 2'' 52 - 33 19 2
Z 0140 05 5 2517 60 2 1/2'' 64 - 46 18 2
Z 0160 01 1 1610 42 1 5/8'' 16 - 26 10 1
Z 0160 02 2 2012 50 2'' 28 - 33 5 1
Z 0160 03 160 164 3 2012 50 2'' 40 - 33 7 2
Z 0160 04 4 2517 60 2 1/2'' 52 - 46 6 2
Z 0160 05 5 2517 60 2 1/2'’ 64 - 46 18 2
Z 0180 01 1 1610 42 1 5/8'' 16 - 26 10 1
Z 0180 02 2 2012 50 2'' 28 - 33 5 1
Z 0180 03 180 184 3 2012 50 2'' 40 - 33 7 2
Z 0180 04 4 2517 60 2 1/2'' 52 - 46 6 2
Z 0180 05 5 2517 60 2 1/2'' 64 - 46 18 2
Z 0200 01 1 2012 50 2'' 16 - 33 15 1
Z 0200 02 2 2012 50 2'' 28 - 33 5 1
Z 0200 03 200 204 3 2012 50 2'' 40 - 33 7 2
Z 0200 04 4 2517 60 2 1/2'' 52 3.5 45 3.5 3
Z 0200 05 5 2517 60 2 1/2'' 64 9.5 45 9.5 7
Z 0250 01 1 2012 50 2'' 16 8.0 32 8.0 4
Z 0250 02 2 2012 50 2'' 28 2.0 32 2.0 4
Z 0250 03 250 254 3 2012 50 2'' 40 4.0 32 4 5
Z 0250 04 4 2517 60 2 1/2'' 52 3.5 45 3.5 7
Z 0250 05 5 2517 60 2 1/2'' 64 9.5 45 9.5 5
Z 0315 01 1 2012 50 2'' 16 8.0 32 8.0 4
Z 0315 02 2 2012 50 2'' 28 2.0 32 2.0 4
Z 0315 03 315 319 3 2517 60 2 1/2'' 40 2.5 45 2.5 4
Z 0315 04 4 2517 60 2 1/2'' 52 3.5 45 3.5 5
Z 0315 05 5 2517 60 2 1/2'' 64 9.5 45 9.5 5
Z 0400 01 1 2012 50 2'' 16 8.0 32 8.0 4
Z 0400 02 2 2517 60 2 1/2'' 28 8.5 45 8.5 4
Z 0400 03 400 404 3 2517 60 2 1/2'' 40 2.5 45 2.5 4
Z 0400 04 4 2517 60 2 1/2'' 52 3.5 45 3.5 5
Z 0400 05 5 3020 75 3'' 64 6.5 51 6.5 5
Z 0500 02 2 2517 60 2 1/2'' 28 8.5 45 8.5 4
Z 0500 03 3 2517 60 2 1/2'' 40 2.5 45 2.5 4
500 504
Z 0500 04 4 3020 75 3'' 52 0.5 51 0.5 5
Z 0500 05 5 3020 75 3'' 64 6.0 76 6.0 5
• Above ‘Pulley Description’ is for ‘Z’ section Pulleys, replace ‘Z’ with ZX, SPZ or XPZ to arrive at respective Pulley / Product code
• Please refer ‘PIX recommended minimum pulley diameter’ charts given on page no. 3
• Unlisted sizes are available on request
6
- PowerWare®
A / AX & SPA / XPA section Pulleys
F F F F F F F F
PD PD PD PD
PD PD
OD OD OD OD OD OD PD OD
OD PD
M L M K L M K M K M K L K M
L L L L L
Type: 1 Type: 2 Type: 3 Type: 4 Type: 5 Type: 6 Type: 7 Type: 8
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
(PD) (OD)
of
Number Metric Imperial
F K L M Type
Code grooves
(mm) (mm) (mm) (mm)
A 0067 01 1 1108 28 1 1/8'' 20 - 22 2.0 1
67 72.5
A 0067 02 2 1108 28 1 1/8'' 35 13 22 - 6
A 0071 01 1 1108 28 1 1/8'' 20 - 22 2.0 1
A 0071 02 71 76.5 2 1108 28 1 1/8'' 35 13 22 - 6
A 0071 03 3 1108 28 1 1/8'' 50 28 22 - 6
A 0075 01 1 1108 28 1 1/8'' 20 - 22 2.0 1
A 0075 02 75 80.5 2 1108 28 1 1/8'' 35 13 22 - 6
A 0075 03 3 1210 32 1 1/4'' 50 25 25 - 6
A 0080 01 1 1108 28 1 1/8'' 20 - 22 2.0 1
A 0080 02 2 1108 28 1 1/8'' 35 13 22 - 6
A 0080 03 80 85.5 3 1210 32 1 1/4'' 50 25 25 - 6
A 0080 04 4 1215 32 1 1/4'' 65 27 38 - 6
A 0080 05 5 1215 32 1 1/4'' 80 42 38 - 6
A 0085 01 1 1108 28 1 1/8'' 20 - 22 2.0 1
A 0085 02 2 1108 28 1 1/8'' 35 13 22 - 6
A 0085 03 85 90.5 3 1210 32 1 1/4'' 50 25 25 - 6
A 0085 04 4 1215 32 1 1/4'' 65 27 38 - 6
A 0085 05 5 1215 32 1 1/4'' 80 42 38 - 6
A 0090 01 1 1210 32 1 1/4'' 20 - 22 2.0 1
A 0090 02 2 1210 32 1 1/4'' 35 13 22 - 6
A 0090 03 90 95.5 3 1610 42 1 5/8'' 50 25 25 - 6
A 0090 04 4 1615 42 1 5/8'' 65 13.5 38 13.5 3
A 0090 05 5 1615 42 1 5/8'' 80 21 38 21.0 3
A 0095 01 1 1610 42 1 5/8'' 20 - 22 2.0 1
A 0095 02 2 1610 42 1 5/8'' 35 10 22 - 6
A 0095 03 95 105.5 3 1610 42 1 5/8'' 50 25 25 - 6
A 0095 04 4 1615 42 1 5/8'' 65 13.5 38 13.5 3
A 0095 05 5 1615 42 1 5/8'' 80 21 38 21.0 3
A 0100 01 1 1610 42 1 5/8'' 20 - 25 5.0 1
A 0100 02 2 1610 42 1 5/8'' 35 10 25 - 6
A 0100 03 3 1610 42 1 5/8'' 50 25 25 - 6
100 105.5
A 0100 04 4 1615 42 1 5/8'' 65 27 38 - 6
A 0100 05 5 1615 42 1 5/8'' 80 42 38 - 6
A 0100 06 6 1615 42 1 5/8'' 95 28.5 38 28.5 6
A 0106 01 1 1610 42 1 5/8'' 20 - 25 5.0 1
A 0106 02 2 1610 42 1 5/8'' 35 10 25 - 6
A 0106 03 106 111.5 3 1610 42 1 5/8'' 50 25 25 - 6
A 0106 04 4 1615 42 1 5/8'' 65 27 38 - 6
A 0106 05 5 2012 50 2'' 80 48 32 - 6
A 0106 06 6 2012 50 2'' 95 31.5 32 31.5 6
7
- PowerWare®
A / AX & SPA / XPA section Pulleys
8
- PowerWare®
A / AX & SPA / XPA section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD)
grooves Number Metric Imperial Type
(mm) (mm) (mm) (mm)
A 0190 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0190 02 2 2012 50 2'' 35 - 32 3.0 2
A 0190 03 3 2517 60 2 1/2'' 50 - 45 5.0 2
190 195.5
A 0190 04 4 3020 75 3'' 65 - 51 14.0 2
A 0190 05 5 3020 75 3'' 80 - 51 29.0 2
A 0190 06 6 3020 75 3'' 95 - 51 22.0 2
A 0200 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0200 02 2 2517 60 2 1/2'' 35 - 45 10.0 8
A 0200 03 3 2517 60 2 1/2'' 50 - 45 5.0 3
200 205.5
A 0200 04 4 3020 75 3'' 65 - 51 14.0 2
A 0200 05 5 3020 75 3'' 80 - 51 29.0 2
A 0200 06 6 3020 75 3'' 95 - 51 22.0 2
A 0212 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0212 02 2 2517 60 2 1/2'' 35 - 45 10.0 8
A 0212 03 3 2517 60 2 1/2'' 50 - 45 5.0 3
212 217.5
A 0212 04 4 3020 75 3'' 65 - 51 14.0 2
A 0212 05 5 3020 75 3'' 80 - 51 29.0 2
A 0212 06 6 3020 75 3'' 95 - 51 44.0 2
A 0224 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0224 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0224 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 3
224 229.5
A 0224 04 4 3020 75 3'' 65 - 51 14.0 2
A 0224 05 5 3020 75 3'' 80 - 51 29.0 2
A 0224 06 6 3020 75 3'' 95 - 51 44.0 2
A 0236 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0236 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0236 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 3
236 241.5
A 0236 04 4 3020 75 3'' 65 - 51 14.0 2
A 0236 05 5 3020 75 3'' 80 - 51 29.0 2
A 0236 06 6 3020 75 3'' 95 - 51 44.0 2
A 0250 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0250 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0250 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 7
250 255.5
A 0250 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0250 05 5 3020 75 3'' 80 14.5 51 14.5 7
A 0250 06 6 3020 75 3'' 95 22.0 51 22.0 7
A 0265 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0265 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0265 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 7
265 270.5
A 0265 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0265 05 5 3020 75 3'' 80 14.5 51 14.5 7
A 0265 06 6 3020 75 3'' 95 22.0 51 22.0 7
A 0280 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0280 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0280 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 7
280 285.5
A 0280 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0280 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0280 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
A 0300 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0300 02 2 2517 60 2 1/2'' 35 - 45 - 8
A 0300 03 3 2517 60 2 1/2'' 50 2.5 45 2.5 7
300 305.5
A 0300 04 4 3020 75 3'' 65 3.5 51 3.5 7
A 0300 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0300 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
9
- PowerWare®
A / AX & SPA / XPA section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD)
grooves Number Metric Imperial Type
(mm) (mm) (mm) (mm)
A 0315 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0315 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0315 03 3 3020 75 3'' 50 - 51 - 8
315 320.5
A 0315 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0315 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0315 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
A 0335 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0335 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0335 03 3 3020 75 3'' 50 - 51 - 8
335 340.5
A 0335 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0335 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0335 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
A 0355 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0355 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0355 03 3 3020 75 3'' 50 - 51 1.0 6
355 360.5
A 0355 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0355 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0355 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
A 0375 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0375 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0375 03 3 3020 75 3'' 50 - 51 - 8
375 380.5
A 0375 04 4 3020 75 3'' 65 7.0 51 7.0 7
A 0375 05 5 3535 90 3 1/2'' 80 - 89 - 8
A 0375 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 7
A 0400 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0400 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0400 03 3 3020 75 3'' 50 0.5 51 0.5 4
400 405.5
A 0400 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0400 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0400 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 4
A 0425 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0425 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0425 03 3 3020 75 3'' 50 0.5 51 0.5 4
425 430.5
A 0425 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0425 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0425 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 4
A 0450 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0450 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0450 03 3 3020 75 3'' 50 0.5 51 0.5 4
450 455.5
A 0450 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0450 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0450 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 4
A 0475 01 1 2012 50 2'' 20 6.0 32 6.0 4
A 0475 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0475 03 3 3020 75 3'' 50 0.5 51 0.5 4
475 480.5
A 0475 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0475 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0475 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 4
A 0500 01 1 2517 60 2 1/2'' 20 12.5 45 12.5 4
A 0500 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0500 03 3 3020 75 3'' 50 0.5 51 0.5 4
500 505.5
A 0500 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0500 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0500 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 4
10
- PowerWare®
A / AX & SPA / XPA section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
grooves Number
(mm) (mm) (mm) (mm)
A 0530 01 1 2517 60 2 1/2'' 20 12.5 45 12.5 4
A 0530 02 2 2517 60 2 1/2'' 35 5.0 45 5.0 4
A 0530 03 3 3020 75 3'' 50 0.5 51 0.5 4
530 535.5
A 0530 04 4 3020 75 3'' 65 7.0 51 7.0 5
A 0530 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0530 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 5
A 0560 01 1 3020 75 3'' 20 6.0 32 6.0 4
A 0560 02 2 3020 75 3'' 35 5.0 45 5.0 4
A 0560 03 3 3020 75 3'' 50 0.5 51 0.5 4
560 565.5
A 0560 04 4 3535 90 3 1/2'' 65 7.0 51 7.0 4
A 0560 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0560 06 6 3535 90 3 1/2'' 95 3.0 89 3.0 5
A 0630 01 1 3020 75 3'' 20 15.5 51 15.5 4
A 0630 02 2 3020 75 3'' 35 8.0 51 8.0 4
A 0630 03 3 3020 75 3'' 50 0.5 51 0.5 4
630 635.5
A 0630 04 4 3535 90 3 1/2'' 65 12.0 89 12.0 4
A 0630 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0630 06 6 4040 100 4'' 95 3.5 102 3.5 4
A 0710 03 3 3020 75 3'' 50 0.5 51 0.5 4
A 0710 04 4 3535 90 3 1/2'' 65 12.0 89 - 4
710 715.5
A 0710 05 5 3535 90 3 1/2'' 80 4.5 89 4.5 4
A 0710 06 6 4040 100 4'' 95 3.5 102 3.5 4
A 0800 03 3 3535 90 3 1/2'' 50 19.5 89 19.5 4
A 0800 04 4 3535 90 3 1/2'' 65 12.0 89 12.0 4
800 805.5
A 0800 05 5 4040 100 4'' 80 11.0 102 11.0 4
A 0800 06 6 4040 100 4'’ 95 3.5 102 3.5 4
• Above ‘Pulley Description’ is for ‘A’ section Pulleys, replace ‘A’ with AX, SPA or XPA to arrive at respective Pulley / Product code
• Please refer ‘PIX recommended minimum pulley diameter’ charts given on page no. 3
• Unlisted sizes are available on request
11
- PowerWare®
B / BX & SPB / XPB section Pulleys
F F F F F F F F
PD PD PD PD
PD PD
OD OD OD OD OD OD PD OD
OD PD
M L M K L M K M K M K L K M
L L L L L
Type: 1 Type: 2 Type: 3 Type: 4 Type: 5 Type: 6 Type: 7 Type: 8
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
grooves Number
(mm) (mm) (mm) (Inches)
B 0100 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0100 02 100 107 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0100 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
B 0106 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0106 02 106 113 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0106 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
B 0112 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0112 02 112 119 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0112 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
B 0118 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0118 02 118 125 2 1610 42 1 5/8'' 44 - 25 19.0 6
B 0118 03 3 1610 42 1 5/8'' 63 - 25 38.0 6
B 0125 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0125 02 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0125 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
125 132
B 0125 04 4 2012 50 2'' 82 25.0 32 25.0 3
B 0125 05 5 2012 50 2'' 101 34.5 32 34.5 3
B 0125 06 6 2012 50 2'' 120 44.0 32 44.0 3
B 0132 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0132 02 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0132 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
132 139
B 0132 04 4 2012 50 2'' 82 25.0 32 25.0 3
B 0132 05 5 2012 50 2'' 101 - 32 69.0 2
B 0132 06 6 2012 50 2'' 120 44.0 32 44.0 3
B 0140 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0140 02 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0140 03 3 1610 42 1 5/8'' 63 38.0 25 - 6
140 147
B 0140 04 4 2012 50 2'' 82 25.0 32 25.0 3
B 0140 05 5 2012 50 2'' 101 - 32 69.0 2
B 0140 06 6 2517 60 2 1/2'' 120 44.0 32 44.0 3
B 0150 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0150 02 2 1610 42 1 5/8'' 44 19.0 25 - 6
B 0150 03 3 2012 50 2'' 63 31.0 32 - 6
B 0150 04 150 157 4 2012 50 2'' 82 25.0 32 25.0 3
B 0150 05 5 2517 60 2 1/2'' 101 - 45 56.0 2
B 0150 06 6 2517 60 2 1/2'' 120 - 45 75.0 2
B 0150 08 8 2517 60 2 1/2'' 158 56.5 45 56.5 2
B 0160 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0160 02 2 2012 50 2'' 44 12.0 32 - 6
B 0160 03 3 2517 60 2 1/2'' 63 18.0 45 - 6
B 0160 04 160 167 4 2517 60 2 1/2'' 82 18.5 45 18.5 3
B 0160 05 5 2517 60 2 1/2'' 101 28.0 45 28.0 3
B 0160 06 6 2517 60 2 1/2'' 120 - 45 75.0 2
B 0160 08 8 3020 75 3'' 158 51.5 51 53.5 3
12
- PowerWare®
B / BX & SPB / XPB section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
grooves Number
(mm) (mm) (mm) (Inches)
B 0170 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0170 02 2 2012 50 2'' 44 12.0 32 - 6
B 0170 03 3 2517 60 2 1/2'' 63 18.0 45 - 6
B 0170 04 170 177 4 2517 60 2 1/2'' 82 18.5 45 18.5 3
B 0170 05 5 3020 75 3'' 101 28.0 51 25.0 3
B 0170 06 6 3020 75 3'' 120 - 51 69.0 2
B 0170 08 8 3030 75 3'' 158 41.0 76 41.0 3
B 0180 01 1 1610 42 1 5/8'' 25 - 25 - 1
B 0180 02 2 2012 50 2'' 44 12.0 32 - 6
B 0180 03 3 2517 60 2 1/2'' 63 18.0 45 - 6
B 0180 04 180 187 4 2517 60 2 1/2'' 82 18.5 45 18.5 3
B 0180 05 5 3020 75 3'' 101 25.0 51 25.0 3
B 0180 06 6 3020 75 3'' 120 - 51 69.0 2
B 0180 08 8 3030 75 3'' 158 41.0 76 41.0 3
B 0190 01 1 2012 50 2'' 25 - 32 - 1
B 0190 02 2 2517 60 2 1/2'' 44 - 45 - 1
B 0190 03 3 2517 60 2 1/2'' 63 18.0 45 - 6
B 0190 04 190 197 4 2517 60 2 1/2'' 82 18.5 45 18.5 3
B 0190 05 5 3020 75 3'' 101 28.0 51 25.0 3
B 0190 06 6 3020 75 3'' 120 - 51 75.0 2
B 0190 08 8 3030 75 3'' 158 41.0 76 41.0 3
B 0200 01 1 2012 50 2'' 25 - 32 7.0 1
B 0200 02 2 2517 60 2 1/2'' 44 - 45 1.0 1
B 0200 03 3 2517 60 2 1/2'' 63 - 45 18.0 2
B 0200 04 200 207 4 3020 75 3'' 82 - 51 31.0 2
B 0200 05 5 3020 75 3'' 101 - 51 50.0 2
B 0200 06 6 3020 75 3'' 120 - 51 69.0 2
B 0200 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 3
B 0212 01 1 2012 50 2'' 25 - 32 7.0 1
B 0212 02 2 2517 60 2 1/2'' 44 - 45 1.0 1
B 0212 03 3 2517 60 2 1/2'' 63 - 45 18.0 2
B 0212 04 212 219 4 3020 75 3'' 82 - 51 31.0 2
B 0212 05 5 3020 75 3'' 101 - 51 50.0 2
B 0212 06 6 3020 75 3'' 120 - 51 69.0 2
B 0212 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 3
B 0224 01 1 2012 50 2'' 25 - 32 7.0 1
B 0224 02 2 2517 60 2 1/2'' 44 - 45 1.0 1
B 0224 03 3 2517 60 2 1/2'' 63 - 45 18.0 2
B 0224 04 4 3020 75 3'' 82 - 51 31.0 2
224 231
B 0224 05 5 3020 75 3'' 101 - 51 50.0 2
B 0224 06 6 3020 75 3'' 120 - 51 69.0 2
B 0224 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 3
B 0224 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 3
B 0236 01 1 2012 50 2'' 25 - 32 7.0 1
B 0236 02 2 2517 60 2 1/2'' 44 - 45 1.0 1
B 0236 03 3 2517 60 2 1/2'' 63 - 45 18.0 2
B 0236 04 4 3020 75 3'' 82 - 51 31.0 2
236 243
B 0236 05 5 3020 75 3'' 101 - 51 50.0 2
B 0236 06 6 3020 75 3'' 120 - 51 69.0 2
B 0236 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 3
B 0236 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 3
B 0250 01 1 2012 50 2'' 25 - 32 7.0 1
B 0250 02 2 2517 60 2 1/2'' 44 - 45 - 8
B 0250 03 3 3020 75 3'' 63 - 51 12.0 2
B 0250 04 4 3020 75 3'' 82 - 51 31.0 2
250 257
B 0250 05 5 3020 75 3'' 101 - 51 50.0 2
B 0250 06 6 3020 75 3'' 120 - 51 69.0 2
B 0250 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 3
B 0250 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 3
13
- PowerWare®
B / BX & SPB / XPB section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
grooves Number
(mm) (mm) (mm) (Inches)
B 0265 01 1 2012 50 2'' 25 - 32 7.0 1
B 0265 02 2 2517 60 2 1/2'' 44 - 45 - 8
B 0265 03 3 3020 75 3'' 63 6.0 51 6.0 7
B 0265 04 4 3020 75 3'' 82 15.5 51 15.5 7
265 272
B 0265 05 5 3535 90 3 1/2'' 101 6.0 89 6.0 7
B 0265 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0265 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 7
B 0265 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 7
B 0280 01 1 2012 50 2'' 25 - 32 7.0 1
B 0280 02 2 2517 60 2 1/2'' 44 - 45 - 8
B 0280 03 3 3020 75 3'' 63 6.0 51 6.0 7
B 0280 04 4 3020 75 3'' 82 15.5 51 15.5 7
280 287
B 0280 05 5 3535 90 3 1/2'' 101 6.0 89 6.0 7
B 0280 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0280 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 7
B 0280 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 7
B 0300 01 1 2012 50 2'' 25 - 32 7.0 1
B 0300 02 2 2517 60 2 1/2'' 44 - 45 - 8
B 0300 03 3 3020 75 3'' 63 6.0 51 6.0 7
B 0300 04 4 3535 90 3 1/2'' 82 - 51 - 8
300 307
B 0300 05 5 3535 90 3 1/2'' 101 6.0 89 6.0 7
B 0300 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0300 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 7
B 0300 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 7
B 0315 01 1 2012 50 2'' 25 - 32 7.0 1
B 0315 02 2 2517 60 2 1/2'' 44 - 45 - 8
B 0315 03 3 3020 75 3'' 63 6.0 51 6.0 7
B 0315 04 4 3535 90 3 1/2'' 82 - 51 - 8
315 322
B 0315 05 5 3535 90 3 1/2'' 101 6.0 89 6.0 7
B 0315 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0315 08 8 3535 90 3 1/2'' 158 34.5 89 35.0 7
B 0315 10 10 3535 90 3 1/2'' 196 53.5 89 53.5 7
B 0335 02 2 2517 60 2 1/2'' 44 - 45 1.0 1
B 0335 03 3 3020 75 3'' 63 6.0 51 6.0 7
B 0335 04 4 3535 90 3 1/2'' 82 - 51 - 8
B 0335 05 335 342 5 3535 90 3 1/2'' 101 3.5 89 6.0 7
B 0335 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0335 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 7
B 0335 10 10 4040 100 4'' 196 53.5 89 47.0 7
B 0355 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0355 03 3 3020 75 3'' 63 6.0 51 6.0 5
B 0355 04 4 3535 90 3 1/2'' 82 - 89 - 8
B 0355 05 355 362 5 3535 90 3 1/2'' 101 6.0 89 6.0 7
B 0355 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 7
B 0355 08 8 3535 90 3 1/2'' 158 34.5 89 34.5 7
B 0355 10 10 4040 100 4'' 196 47.0 102 47.0 7
B 0375 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0375 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0375 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0375 05 375 382 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0375 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 5
B 0375 08 8 4040 100 4'' 158 28.0 102 28.0 5
B 0375 10 10 4040 100 4'' 196 47.0 102 47.0 5
14
- PowerWare®
B / BX & SPB / XPB section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
Type
grooves Number
(mm) (mm) (mm) (Inches)
B 0400 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0400 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0400 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0400 05 400 407 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0400 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 5
B 0400 08 8 4040 100 4'' 158 28.0 102 28.0 5
B 0400 10 10 4040 100 4'' 196 47.0 102 47.0 5
B 0425 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0425 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0425 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0425 05 425 432 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0425 06 6 3535 90 3 1/2'' 120 15.5 89 15.5 5
B 0425 08 8 4040 100 4'' 158 28.0 102 28.0 5
B 0425 10 10 4040 100 4'' 196 47.0 102 47.0 5
B 0450 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0450 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0450 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0450 05 450 457 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0450 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0450 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0450 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0475 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0475 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0475 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0475 05 475 482 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0475 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0475 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0475 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0500 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0500 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0500 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0500 05 500 507 5 3535 90 3 1/2'' 101 6.0 89 6.0 5
B 0500 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0500 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0500 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0530 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0530 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0530 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0530 05 530 537 5 4040 100 4'' 101 0.5 102 0.5 4
B 0530 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0530 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0530 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0560 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0560 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0560 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0560 05 560 567 5 4040 100 4'' 101 0.5 102 0.5 4
B 0560 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0560 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0560 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
15
- PowerWare®
B / BX & SPB / XPB section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
Type
grooves Number
(mm) (mm) (mm) (Inches)
B 0600 02 2 3020 75 3'' 44 3.5 51 3.5 4
B 0600 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0600 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0600 05 600 607 5 4040 100 4'' 101 0.5 102 0.5 4
B 0600 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0600 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0600 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0630 02 2 3030 75 3'' 44 16.0 76 16.0 4
B 0630 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0630 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0630 05 630 637 5 4040 100 4'' 101 0.5 102 0.5 4
B 0630 06 6 4040 100 4'' 120 9.0 102 9.0 5
B 0630 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0630 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0710 02 2 3030 75 3'' 44 16.0 76 16.0 4
B 0710 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0710 04 4 3535 90 3 1/2'' 82 3.5 89 3.5 4
B 0710 05 710 717 5 4040 100 4'' 101 0.5 102 0.5 4
B 0710 06 6 4545 110 4 1/2'' 120 3.0 114 3.0 5
B 0710 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0710 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0762 02 2 3030 75 3'' 44 16.0 76 16.0 4
B 0762 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0762 04 4 4040 100 4'' 82 10.0 102 10.0 4
B 0762 05 762 769 5 4040 100 4'' 101 0.5 102 0.5 4
B 0762 06 6 4545 110 4 1/2'' 120 3.0 114 3.0 5
B 0762 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0762 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0800 02 2 3030 75 3'' 44 16.0 76 16.0 4
B 0800 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0800 04 4 4040 100 4'' 82 10.0 102 10.0 4
B 0800 05 800 807 5 4040 100 4'' 101 0.5 102 0.5 4
B 0800 06 6 4545 110 4 1/2'' 120 3.0 114 3.0 5
B 0800 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0800 10 10 4545 110 4 1/2'' 196 41.0 114 41.0 5
B 0900 03 3 3535 90 3 1/2'' 63 13.0 89 13.0 4
B 0900 04 4 4040 100 4'' 82 10.0 102 10.0 4
B 0900 05 5 4545 110 4 1/2'' 101 6.5 114 6.5 4
900 907
B 0900 06 6 4545 110 4 1/2'' 120 3.0 114 3.0 5
B 0900 08 8 4545 110 4 1/2'' 158 22.0 114 22.0 5
B 0900 10 10 5050 125 5'' 196 34.5 127 34.5 5
B 1000 03 3 4040 100 4'' 63 19.5 102 19.5 4
B 1000 04 4 4040 100 4'' 82 10.0 102 10.0 4
B 1000 05 5 4545 110 4 1/2'' 101 6.5 114 6.5 4
1000 1007
B 1000 06 6 4545 110 4 1/2'' 120 3.0 127 3.0 5
B 1000 08 8 5050 125 5'' 158 15.5 127 15.5 5
B 1000 10 10 5050 125 5'' 196 34.5 127 34.5 5
B 1250 03 3 4040 100 4'' 63 19.5 102 19.5 4
B 1250 04 4 4040 100 4'' 82 10.0 102 10.0 4
B 1250 05 5 4545 110 4 1/2'' 101 6.5 114 6.5 4
1250 1257
B 1250 06 6 5050 125 5'' 120 3.0 127 3.0 5
B 1250 08 8 5050 125 5'' 158 15.5 127 15.5 5
B 1250 10 10 5050 125 5'' 196 34.5 127 34.5 5
• Above ‘Pulley Description’ is for ‘B’ section Pulleys, replace ‘B’ with BX, SPB or XPB to arrive at respective Pulley / Product code
• Please refer ‘PIX recommended minimum pulley diameter’ charts given on page no. 3
• Unlisted sizes are available on request
16
- PowerWare®
C / CX & SPC / XPC section Pulleys
F F F F F F F F
PD PD PD PD
PD PD
OD OD OD OD OD OD PD OD
OD PD
M L M K L M K M K M K L K M
LL L L L L
Type: 1 Type: 2 Type: 3 Type: 4 Type: 5 Type: 6 Type: 7 Type: 8
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
grooves Number
(mm) (mm) (mm) (Inches)
C 0200 03 3 2517 60 2 1/2'' 85 - 45 40.0 2
C 0200 04 4 3020 75 3'' 111 30.0 51 30.0 3
C 0200 05 5 3535 90 3 1/2'' 136 16.0 89 31.0 3
200 209.6
C 0200 06 6 3535 90 3 1/2'' 162 16.0 89 57.0 3
C 0200 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0200 08 8 3535 90 3 1/2'' 213 46.0 89 78.0 3
C 0212 03 3 3020 75 3'' 85 - 51 34.0 2
C 0212 04 4 3020 75 3'' 111 30.0 51 30.0 3
C 0212 05 5 3535 90 3 1/2'' 136 16.0 89 31.0 3
212 221.6
C 0212 06 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0212 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0212 08 8 3535 90 3 1/2'' 213 46.0 89 78.0 3
C 0224 03 3 3020 75 3'' 85 - 51 34.0 2
C 0224 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 3
C 0224 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 3
224 233.6
C 0224 06 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0224 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0224 08 8 3535 90 3 1/2'' 213 46.0 89 78.0 3
C 0236 03 3 3020 75 3'' 85 - 51 34.0 2
C 0236 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 3
C 0236 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 3
236 245.6
C 0236 06 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0236 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0236 08 8 3535 90 3 1/2'' 213 46.0 89 78.0 3
C 0250 03 3 3020 75 3'' 85 - 51 34.0 2
C 0250 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 3
C 0250 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 3
C 0250 06 250 259.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0250 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0250 08 8 3535 90 3 1/2'' 213 62.0 89 62.0 3
C 0250 10 10 4040 100 4'' 264 81.0 102 81.0 3
C 0265 03 3 3535 90 3 1/2'' 89 2.0 85 2.0 7
C 0265 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 3
C 0265 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 3
C 0265 06 265 274.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0265 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0265 08 8 3535 90 3 1/2'' 213 62.0 89 62.0 3
C 0265 10 10 4040 100 4'' 264 81.0 102 81.0 3
17
- PowerWare®
C / CX & SPC / XPC section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
Type
grooves Number
(mm) (mm) (mm) (Inches)
C 0280 03 3 3535 90 3 1/2'' 89 2.0 85 2.0 7
C 0280 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 3
C 0280 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 3
C 0280 06 280 289.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 3
C 0280 07 7 3535 90 3 1/2'' 187 36.0 89 62.0 3
C 0280 08 8 3535 90 3 1/2'' 213 62.0 89 62.0 3
C 0280 10 10 4040 100 4'' 264 81.0 102 81.0 3
C 0300 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0300 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 7
C 0300 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 7
C 0300 06 300 309.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 7
C 0300 07 7 3535 90 3 1/2'' 187 49.0 89 49.0 7
C 0300 08 8 4040 100 4'' 213 55.5 102 55.5 3
C 0300 10 10 4545 110 4 1/2'' 264 75.0 114 75.0 3
C 0315 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0315 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 7
C 0315 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 7
C 0315 06 315 324.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 7
C 0315 07 7 3535 90 3 1/2'' 187 49.0 89 49.0 7
C 0315 08 8 4040 100 4'' 213 55.5 102 55.5 3
C 0315 10 10 4545 110 4 1/2'' 264 75.0 114 75.0 3
C 0335 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0335 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 7
C 0335 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 7
C 0335 06 335 344.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 7
C 0335 07 7 3535 90 3 1/2'' 187 49.0 89 49.0 7
C 0335 08 8 4040 100 4'' 213 55.5 102 55.5 3
C 0335 10 10 4545 110 4 1/2'' 264 75.0 114 75.0 3
C 0355 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0355 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 7
C 0355 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 7
C 0355 06 355 364.6 6 3535 90 3 1/2'' 162 36.5 89 36.5 7
C 0355 07 7 4040 100 4'' 187 42.5 102 42.5 7
C 0355 08 8 4040 100 4'' 213 55.5 102 55.5 7
C 0355 10 10 4545 110 4 1/2'' 264 75.0 114 75.0 7
C 0375 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0375 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 7
C 0375 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 7
C 0375 06 375 384.6 6 4040 100 4'' 162 30.0 102 30.0 7
C 0375 07 7 4040 100 4'' 187 42.5 102 42.5 7
C 0375 08 8 4545 110 4 1/2'' 213 49.5 114 49.5 7
C 0375 10 10 4545 110 4 1/2'' 264 75.0 114 75.0 7
C 0400 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0400 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 5
C 0400 05 5 3535 90 3 1/2'' 136 23.5 89 23.5 5
C 0400 06 400 409.6 6 4040 100 4'' 162 30.0 102 30.0 7
C 0400 07 7 4545 110 4 1/2'' 187 36.5 114 36.5 7
C 0400 08 8 4545 110 4 1/2'' 213 49.5 114 49.5 7
C 0400 10 10 5050 125 5'' 264 68.5 127 68.5 7
C 0425 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0425 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 5
C 0425 05 5 4040 100 4'' 136 17.0 102 17.0 7
C 0425 06 425 434.6 6 4545 110 4 1/2'' 162 24.0 114 24.0 7
C 0425 07 7 4545 110 4 1/2'' 187 36.5 114 36.5 7
C 0425 08 8 5050 125 5'' 213 43.0 127 43.0 7
C 0425 10 10 5050 125 5'' 264 68.5 127 68.5 7
18
- PowerWare®
C / CX & SPC / XPC section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
Type
grooves Number
(mm) (mm) (mm) (Inches)
C 0450 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0450 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 5
C 0450 05 5 4040 100 4'' 136 17.0 102 17.0 5
C 0450 06 450 459.6 6 4545 110 4 1/2'' 162 24.0 114 24.0 7
C 0450 07 7 5050 125 5'' 187 30.0 127 30.0 7
C 0450 08 8 5050 125 5'' 213 43.0 127 43.0 7
C 0450 10 10 5050 125 5'' 264 68.5 127 68.5 7
C 0475 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0475 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 5
C 0475 05 5 4040 100 4'' 136 17.0 102 17.0 5
C 0475 06 475 484.6 6 4545 110 4 1/2'' 162 24.0 114 24.0 7
C 0475 07 7 5050 125 5'' 187 30.0 127 30.0 7
C 0475 08 8 5050 125 5'' 213 43.0 127 43.0 7
C 0475 10 10 5050 125 5'' 264 68.5 127 68.5 7
C 0500 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0500 04 4 3535 90 3 1/2'' 111 11.0 89 11.0 5
C 0500 05 5 4040 100 4'' 136 17.0 102 17.0 5
C 0500 06 500 509.6 6 4545 110 4 1/2'' 162 24.0 114 24.0 5
C 0500 07 7 5050 125 5'' 187 30.0 127 30.0 7
C 0500 08 8 5050 125 5'' 213 43.0 127 43.0 7
C 0500 10 10 5050 125 5'' 264 68.5 127 68.5 7
C 0530 03 3 3535 90 3 1/2'' 85 2.0 89 2.0 4
C 0530 04 4 4040 100 4'' 111 4.5 102 4.5 5
C 0530 05 5 4545 110 4 1/2'' 136 11.0 114 11.0 5
C 0530 06 530 539.6 6 5050 125 5'' 162 17.5 127 17.5 5
C 0530 07 7 5050 125 5'' 187 30.0 127 30.0 7
C 0530 08 8 5050 125 5'' 213 43.0 127 43.0 7
C 0530 10 10 5050 125 5'' 264 68.5 127 68.5 7
C 0560 03 3 3535 90 3 1/2'' 85 - 89 - 8
C 0560 04 4 4040 100 4'' 111 4.5 102 4.5 5
C 0560 05 5 4545 110 4 1/2'' 136 11.0 114 11.0 5
C 0560 06 560 569.6 6 5050 125 5'' 162 17.5 127 17.5 5
C 0560 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 0560 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 0560 10 10 5050 125 5'' 264 68.5 127 68.5 5
C 0600 03 3 4040 100 4'' 85 - 102 - 8
C 0600 04 4 4545 110 4 1/2'' 111 1.5 114 1.5 4
C 0600 05 5 4545 110 4 1/2'' 136 4.5 114 4.5 4
C 0600 06 600 609.6 6 5050 125 5'' 162 17.5 127 17.5 5
C 0600 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 0600 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 0600 10 10 5050 125 5'' 264 68.5 127 68.5 5
C 0630 03 3 4545 110 4 1/2'' 85 14.5 114 14.5 4
C 0630 04 4 4545 110 4 1/2'' 111 1.5 114 1.5 4
C 0630 05 5 5050 125 5'' 136 4.5 127 4.5 5
C 0630 06 630 639.6 6 5050 125 5'' 162 17.5 127 17.5 5
C 0630 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 0630 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 0630 10 10 5050 125 5'' 264 68.5 127 68.5 5
19
- PowerWare®
C / CX & SPC / XPC section Pulleys
Pitch Outer
Number Maximum Bore
Product Diameter Diameter Bush Pulley
Pulley
of F K L M
Code (PD) (OD) Metric Imperial Type
Type
grooves Number
(mm) (mm) (mm) (Inches)
C 0710 03 3 4545 110 4 1/2'' 85 14.5 114 14.5 4
C 0710 04 4 4545 110 4 1/2'' 111 1.5 114 1.5 4
C 0710 05 5 5050 125 5'' 136 4.5 127 4.5 5
C 0710 06 710 719.6 6 5050 125 5'' 162 17.5 127 17.5 5
C 0710 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 0710 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 0710 10 10 5050 125 5'' 264 68.5 127 68.5 5
C 0800 03 3 5050 125 5'' 85 2.0 89 2.5 4
C 0800 04 4 5050 125 5'' 102 4.5 111 4.5 4
C 0800 05 5 5050 125 5'' 136 17.0 102 17.0 5
800 809.6
C 0800 06 6 5050 125 5'' 162 17.5 127 17.5 5
C 0800 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 0800 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 1000 03 3 5050 125 5'' 85 8.5 102 8.5 4
C 1000 04 4 5050 125 5'' 111 8.0 127 8.0 4
C 1000 05 5 5050 125 5'' 136 4.5 127 4.5 5
1000 1009.6
C 1000 06 6 5050 125 5'' 162 17.5 127 17.5 5
C 1000 07 7 5050 125 5'' 187 30.0 127 30.0 5
C 1000 08 8 5050 125 5'' 213 43.0 127 43.0 5
C 1250 03 3 5050 125 5'' 85 8.5 102 8.5 4
C 1250 04 4 5050 125 5'' 111 4.5 127 4.5 4
C 1250 05 5 5050 125 5'' 136 17.5 127 17.5 5
1250 1259.6
C 1250 06 6 5050 125 5'' 162 30.0 127 30.0 5
C 1250 07 7 5050 125 5'' 187 43.0 127 43.0 5
C 1250 08 8 5050 125 5'' 213 43.0 127 43.0 5
• Above ‘Pulley Description’ is for ‘C’ section Pulleys, replace ‘C’ with CX, SPC or XPC to arrive at respective Pulley / Product code
• Please refer ‘PIX recommended minimum pulley diameter’ charts given on page no. 3
• Unlisted sizes are available on request
20
- PowerWare®
3V & 3VX Section Pulleys
F L
F M L
E L M
E E F M
PD OD PD OD
PD
OD
TYPE C
TYPE A 1=Solid 2=Web 3=Arm/
TYPE B
Spoke
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
3V 0265 01 1 1108 1-1/8 28 3/16 11/16 - 7/8 A-1
3V 0265 02 2 1108 1-1/8 28 7/32 7/8 - 1-3/32 A-1
2.60 2.65
3V 0265 03 3 1108 1-1/8 28 5/8 7/8 - 1-1/2 A-1
3V 0265 04 4 1108 1-1/8 28 1-1/32 7/8 - 1-29/32 A-1
3V 0280 01 1 1108 1-1/8 28 3/16 11/16 - 7/8 A-1
3V 0280 02 2 1108 1-1/8 28 7/32 7/8 - 1-3/32 A-1
2.75 2.80
3V 0280 03 3 1108 1-1/8 28 5/8 7/8 - 1-1/2 A-1
3V 0280 04 4 1108 1-1/8 28 1-1/32 7/8 - 1-29/32 A-1
3V 0300 01 1 1108 1-1/8 28 3/16 11/16 - 7/8 A-1
3V 0300 02 2 1210 1-1/4 32 3/32 1 - 1-3/32 A-1
2.95 3.00
3V 0300 03 3 1210 1-1/4 32 1/2 1 - 1-1/2 A-1
3V 0300 04 4 1210 1-1/4 32 29/32 1 - 1-29/32 A-1
3V 0315 01 1 1108 1-1/8 28 3/16 11/16 - 7/8 A-1
3V 0315 02 2 1210 1-1/4 32 3/32 1 - 1-3/32 A-1
3.10 3.15
3V 0315 03 3 1210 1-1/4 32 1/2 1 - 1-1/2 A-1
3V 0315 04 4 1210 1-1/4 32 29/32 1 - 1-29/32 A-1
3V 0335 01 1 1610 1-5/8 42 5/16 1 - 11/16 A-1
3V 0335 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3.30 3.35
3V 0335 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0335 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
3V 0365 01 1 1610 1-5/8 42 5/16 1 - 11/16 A-1
3V 0365 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3.60 3.65
3V 0365 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0365 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
3V 0412 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0412 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
4.07 4.12
3V 0412 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0412 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
3V 0450 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0450 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0450 03 4.45 4.50 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0450 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
3V 0450 05 5 1615 1-5/8 42 - 1-1/2 13/16 2-5/16 A-1
3V 0475 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0475 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0475 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0475 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
4.70 4.75
3V 0475 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0475 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0475 08 8 2517 2-1/2 60 1-25/32 1-3/4 - 3-17/32 A-1
3V 0475 10 10 2517 2-1/2 60 2-29/32 1-3/4 - 4-11/32 A-1
21
- PowerWare®
3V & 3VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter of Bush Pulley
(PD) (OD) E L M F Type
Code grooves Number Imperial Metric
(Inches) (Inches) (Inches) (mm)
3V 0500 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0500 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0500 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0500 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
4.95 5.00
3V 0500 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0500 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0500 08 8 2517 2-1/2 60 1-25/32 1-3/4 - 3-17/32 A-1
3V 0500 10 10 2517 2-1/2 60 2-29/32 1-3/4 - 4-11/32 A-1
3V 0530 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0530 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0530 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0530 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
5.25 5.30
3V 0530 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0530 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0530 08 8 2517 2-1/2 60 1-1/32 1-3/4 3/4 3-17/32 A-1
3V 0530 10 10 2517 2-1/2 60 1-27/32 1-3/4 3/4 4-11/32 A-1
3V 0560 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0560 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0560 03 3 1610 1-5/8 42 1/2 1 - 1-1/2 A-1
3V 0560 04 4 1610 1-5/8 42 29/32 1 - 1-29/32 A-1
5.55 5.60
3V 0560 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0560 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0560 08 8 2517 2-1/2 60 1/4 1-3/4 1-17/32 3-17/32 A-1
3V 0560 01 10 2517 2-1/2 60 1/2 1-3/4 2-3/32 4-11/32 A-1
3V 0600 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0600 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0600 03 3 2517 2-1/2 60 5/32 1-3/4 13/32 1-1/2 B-1
3V 0600 04 4 2517 2-1/2 60 5/32 1-3/4 - 1-29/32 A-1
5.95 6.00
3V 0600 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0600 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0600 08 8 2517 2-1/2 60 1/4 1-3/4 1-17/32 3-17/32 A-1
3V 0600 01 10 2517 2-1/2 60 1/2 1-3/4 2-3/32 4-11/32 A-1
3V 0650 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0650 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0650 03 3 2517 2-1/2 60 5/32 1-1/2 13/32 1-3/4 B-1
3V 0650 04 4 2517 2-1/2 60 5/32 1-3/4 - 1-29/32 A-1
6.45 6.50
3V 0650 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0650 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0650 08 8 2517 2-1/2 60 1/4 1-3/4 1-17/32 3-17/32 A-1
3V 0650 01 10 2517 2-1/2 60 1/2 1-3/4 2-3/32 4-11/32 A-1
3V 0690 01 1 1610 1-5/8 42 - 11/16 5/16 1 B-1
3V 0690 02 2 1610 1-5/8 42 3/32 1 - 1-3/32 A-1
3V 0690 03 3 2517 2-1/2 60 5/32 1-1/2 13/32 1-3/4 B-1
3V 0690 04 4 2517 2-1/2 60 5/32 1-3/4 - 1-29/32 A-1
6.85 6.90
3V 0690 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0690 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0690 08 8 2517 2-1/2 60 1/4 1-3/4 1-17/32 3-17/32 A-1
3V 0690 10 10 2517 2-1/2 60 1/2 1-3/4 2-3/32 4-11/32 A-1
22
- PowerWare®
3V & 3VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter of Bush Pulley
(PD) (OD) E L M F Type
Code grooves Number Imperial Metric
(Inches) (Inches) (Inches) (mm)
3V 0800 01 1 2517 2-1/2 60 - 1-1/16 11/16 1-3/4 B-2
3V 0800 02 2 2517 2-1/2 60 - 1-3/32 21/32 1-3/4 B-2
3V 0800 03 3 2517 2-1/2 60 5/32 1-1/2 13/32 1-3/4 B-1
3V 0800 04 4 2517 2-1/2 60 5/32 1-3/4 - 1-29/32 A-1
7.95 8.00
3V 0800 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-1
3V 0800 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-1
3V 0800 08 8 3020 3 75 1/2 2 1-1/32 3-17/32 A-1
3V 0800 10 10 3020 3 75 1/4 2 2-3/32 4-11/32 A-1
3V 1060 01 1 2517 2-1/2 60 - 1-1/16 11/16 1-3/4 B-2
3V 1060 02 2 2517 2-1/2 60 - 1-3/32 21/32 1-3/4 B-2
3V 1060 03 3 2517 2-1/2 60 - 1-1/2 1/4 1-3/4 B-2
3V 1060 04 4 2517 2-1/2 60 5/32 1-3/4 - 1-29/32 A-2
10.55 10.60
3V 1060 05 5 2517 2-1/2 60 9/16 1-3/4 - 2-5/16 A-2
3V 1060 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-2
3V 1060 08 8 3020 3 75 1/2 2 1-1/32 3-17/32 A-2
3V 1060 10 10 3020 3 75 27/32 2 1-1/2 4-11/32 A-2
3V 1400 01 1 2517 2-1/2 60 - 15/16 13/16 1-3/4 B-3
3V 1400 02 2 2517 2-1/2 60 - 1-3/32 21/32 1-3/4 B-3
3V 1400 03 3 2517 2-1/2 60 - 1-1/2 1/4 1-3/4 B-3
3V 1400 04 4 2517 2-1/2 60 - 1-3/4 5/32 1-29/32 A-3
13.95 14.00
3V 1400 05 5 2517 2-1/2 60 - 1-3/4 9/16 2-5/16 A-3
3V 1400 06 6 2517 2-1/2 60 31/32 1-3/4 - 2-23/32 A-3
3V 1400 08 8 3020 3 75 21/32 2 7/8 3-17/32 A-3
3V 1400 10 10 3535 3-1/2 90 - 3-1/2 27/32 4-11/32 A-2
3V 1900 01 1 3020 3 75 - 13/16 1-3/16 2 B-3
3V 1900 02 2 3020 3 75 - 1-3/32 29/32 2 B-3
3V 1900 03 3 3020 3 75 - 1-1/2 1/2 2 B-3
3V 1900 04 4 3020 3 75 - 2 3/32 1-29/32 C-3
18.95 19.00
3V 1900 05 5 3020 3 75 - 2 5/16 2-5/16 A-3
3V 1900 06 6 3020 3 75 - 2 23/32 2-23/32 A-3
3V 1900 08 8 3535 3-1/2 90 - 3-1/2 1/32 3-17/32 A-3
3V 1900 10 10 3535 3-1/2 90 - 3-1/2 27/32 4-11/32 A-3
3V 2500 02 2 3020 3 75 1/8 2 25/32 1-3/32 C-3
3V 2500 03 3 3020 3 75 - 2 1/2 1-1/2 B-3
3V 2500 04 4 3020 3 75 - 2 3/32 1-29/32 C-3
3V 2500 05 24.95 25.00 5 3030 3 75 - 3 11/16 2-5/16 B-3
3V 2500 06 6 3030 3 75 - 3 9/32 2-23/32 B-3
3V 2500 08 8 3535 3-1/2 90 - 3-1/2 1/32 3-17/32 A-3
3V 2500 10 10 4040 4 100 - 4 11/32 4-11/32 A-3
3V 3350 03 3 3020 3 75 1/4 2 1/4 1-1/2 B-3
3V 3350 04 4 3030 3 75 35/64 3 35/64 1-29/32 C-3
3V 3350 05 5 3030 3 75 11/32 3 11/32 2-5/16 C-3
33.45 33.50
3V 3350 06 6 3030 3 75 9/64 3 9/64 2-23/32 C-3
3V 3350 08 8 4040 4 100 15/64 4 15/64 3-17/32 C-3
3V 3350 10 10 4040 4 100 - 4 11/32 4-11/32 A-3
23
- PowerWare®
5V & 5VX Section Pulleys
F L
F M L
E L M
E E F M
PD OD PD OD
PD
OD
TYPE C
TYPE A 1=Solid 2=Web 3=Arm/
TYPE B
Spoke
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter of Bush Pulley
(PD) (OD) E L M F Type
Code grooves Number Imperial Metric
(Inches) (Inches) (Inches) (mm)
5V 0440 02 2 1610 1-5/8 42 1/16 1 5/8 1-11/16 A-1
5V 0440 03 4.3 4.4 3 - - - 1-3/8 - - 2-3/8 -
5V 0440 03 4 - - - 2-1/16 - - 3-1/16 -
5V 0465 02 2 1610 1-5/8 42 1/16 1 5/8 1-11/16 A-1
5V 0465 03 4.55 4.65 3 - - - 1/16 - 1-5/16 2-3/8 -
5V 0465 03 4 - - - 2-1/16 - - 3-1/16 -
5V 0490 02 2 1610 1-5/8 42 1/16 1 5/8 1-11/16 A-1
5V 0490 03 4.80 4.90 3 - - - 1/16 - 1-5/16 2-3/8 -
5V 0490 04 4 - - - 2-1/16 - - 3-1/16 -
5V 0520 02 2 1610 1-5/8 42 1/16 1 5/8 1-11/16 A-1
5V 0520 03 5.10 5.20 3 - - - 1/16 - 1-5/16 2-3/8 -
5V 0520 04 4 - - - 2-1/16 - - 3-1/16 -
5V 0550 02 2 1610 2-1/2 60 1/16 1 5/8 1-11/16 A-1
5V 0550 03 5.40 5.50 3 1610 - - 1/16 1 1-5/16 2-3/8 -
5V 0550 04 4 2517 - - 1-5/16 1-3/4 - 3-1/16 -
5V 0590 02 2 1610 1-5/8 42 1/16 1 5/8 1-11/16 A-1
5V 0590 03 3 2517 2-1/2 60 - 1-3/4 5/8 2-3/8 -
5V 0590 04 5.80 5.90 4 2517 2-1/2 60 1-5/16 1-3/4 - 3-1/16 -
5V 0590 05 5 2517 2-1/2 60 9/16 1-3/4 1-7/16 3-3/4 -
5V 0590 06 6 2517 2-1/2 60 1-1/8 1-3/4 1-9/16 4-7/16 -
5V 0630 02 2 1610 1-5/8 42 - 1 11/16 1-11/16 A-1
5V 0630 03 3 2517 2-1/2 60 - 1-3/4 5/8 2-3/8 -
5V 0630 04 6.20 6.30 4 2517 2-1/2 60 - 1-3/4 1-5/16 3-1/16 -
5V 0630 05 5 2517 2-1/2 60 9/16 1-3/4 1-7/16 3-3/4 -
5V 0630 06 6 2517 2-1/2 60 13/16 1-3/4 1-7/8 4-7/16 -
5V 0670 02 2 1610 1-5/8 42 - 1 11/16 1-11/16 A-1
5V 0670 03 3 2517 2-1/2 60 - 1-3/4 5/8 2-3/8 -
5V 0670 04 6.60 6.70 4 2517 2-1/2 60 - 1-3/4 1-5/16 3-1/16 -
5V 0670 05 5 2517 2-1/2 60 9/16 1-3/4 1-7/16 3-3/4 -
5V 0670 06 6 2517 2-1/2 60 13/16 1-3/4 1-7/8 4-7/16 -
5V 0710 02 2 2517 2-1/2 60 1/16 1-3/4 - 1-11/16 B-1
5V 0710 03 3 2517 2-1/2 60 5/8 1-3/4 - 2-3/8 A-1
5V 0710 04 4 2517 2-1/2 60 1-5/16 1-3/4 - 3-1/16 A-1
7.00 7.10
5V 0710 05 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0710 06 6 3020 3 75 3/4 2 1-11/16 4-7/16 A-1
5V 0710 08 8 3030 3 75 1 3 1-13/16 5-13/16 A-1
5V 0750 02 2 2517 2-1/2 60 1/16 1-3/4 - 1-11/16 B-1
5V 0750 03 3 2517 2-1/2 60 5/8 1-3/4 - 2-3/8 A-1
5V 0750 04 4 2517 2-1/2 60 1-5/16 1-3/4 - 3-1/16 A-1
7.40 7.50
5V 0750 05 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0750 06 6 3020 3 75 3/4 2 1-11/16 4-7/16 A-1
5V 0750 08 8 3030 3 75 1 3 1-13/16 5-13/16 A-1
24
- PowerWare®
5V & 5VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
5V 0800 02 2 2517 2-1/2 60 1/16 1-11/16 0 1-3/4 B-1
5V 0800 03 3 2517 2-1/2 60 5/8 1-3/4 0 2-3/8 A-1
5V 0800 04 4 2517 2-1/2 60 1-5/16 1-3/4 0 3-1/16 A-1
5V 0800 05 7.90 8.00 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0800 06 6 3020 3 75 3/4 2 1-11/16 4-7/16 A-1
5V 0800 08 8 3030 3 75 1 3 1-13/16 5-13/16 A-1
5V 0800 10 10 3030 3 75 1 3 3-3/16 7-3/16 A-1
5V 0850 02 2 2517 2-1/2 60 1/16 1-11/16 0 1-3/4 B-2
5V 0850 03 3 2517 2-1/2 60 5/8 1-3/4 0 2-3/8 A-2
5V 0850 04 4 2517 2-1/2 60 1-5/16 1-3/4 0 3-1/16 A-2
5V 0850 05 8.40 8.50 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0850 06 6 3020 3 75 3/4 2 1-11/16 4-7/16 A-1
5V 0850 08 8 3030 3 75 1 3 1-13/16 5-13/16 A-1
5V 0850 10 10 3030 3 75 1 3 3-3/16 7-3/16 A-1
5V 0900 02 2 2517 2-1/2 60 1/16 1-11/16 0 1-3/4 B-2
5V 0900 03 3 2517 2-1/2 60 5/8 1-3/4 0 2-3/8 A-2
5V 0900 04 4 2517 2-1/2 60 1-5/16 1-3/4 0 3-1/16 A-2
5V 0900 05 8.90 9.00 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0900 06 6 3020 3 75 3/4 2 1-11/16 4-7/16 A-1
5V 0900 08 8 3030 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 0900 10 10 3535 3-1/2 90 1 3-1/2 2-11/16 7-3/16 A-1
5V 0925 02 2 3020 3 75 0 1-11/16 5/16 2 B-2
5V 0925 03 3 3020 3 75 0 2 3/8 2-3/8 A-1
5V 0925 04 4 3020 3 75 1/2 2 9/16 3-1/16 A-1
5V 0925 05 9.15 9.25 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0925 06 6 3535 3-1/2 90 0 3-1/2 15/16 4-7/16 A-1
5V 0925 08 8 3535 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 0925 10 10 4040 4 100 1 4 2-3/16 7-3/16 A-1
5V 0975 02 2 3020 3 75 0 1-11/16 5/16 2 B-2
5V 0975 03 3 3020 3 75 0 2 3/8 2-3/8 A-1
5V 0975 04 4 3020 3 75 1/2 2 9/16 3-1/16 A-1
5V 0975 05 9.65 9.75 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-1
5V 0975 06 6 3535 3-1/2 90 0 3-1/2 15/16 4-7/16 A-1
5V 0975 08 8 3535 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 0975 10 10 4040 4 100 1 4 2-3/16 7-3/16 A-1
5V 1030 02 2 3020 3 75 0 1-11/16 5/16 2 B-2
5V 1030 03 3 3020 3 75 0 2 3/8 2-3/8 A-2
5V 1030 04 4 3020 3 75 1/2 2 9/16 3-1/16 A-2
5V 1030 05 10.20 10.30 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-2
5V 1030 06 6 3535 3-1/2 90 0 3-1/2 15/16 4-7/16 A-1
5V 1030 08 8 3535 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 1030 10 10 4040 4 100 1 4 2-3/16 7-3/16 A-1
5V 1090 02 2 3020 3 75 0 1-11/16 5/16 2 B-2
5V 1090 03 3 3020 3 75 0 2 3/8 2-3/8 A-2
5V 1090 04 4 3020 3 75 1/2 2 9/16 3-1/16 A-2
5V 1090 05 10.80 10.90 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-2
5V 1090 06 6 3535 3-1/2 90 0 3-1/2 15/16 4-7/16 A-1
5V 1090 08 8 3535 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 1090 10 10 4040 4 100 1 4 2-3/16 7-3/16 A-1
5V 1180 02 2 3020 3 75 0 1-11/16 5/16 2 B-2
5V 1180 03 3 3020 3 75 0 2 3/8 2-3/8 A-2
5V 1180 04 4 3020 3 75 1/2 2 9/16 3-1/16 A-2
5V 1180 05 11.70 11.80 5 3020 3 75 1/2 2 1-1/4 3-3/4 A-2
5V 1180 06 6 3535 3-1/2 90 0 3-1/2 15/16 4-7/16 A-2
5V 1180 08 8 3535 3-1/2 90 1 3-1/2 1-5/16 5-13/16 A-1
5V 1180 10 10 4040 4 100 1 4 2-3/16 7-3/16 A-1
25
- PowerWare®
5V & 5VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
5V 1250 02 2 3020 3 75 - 1-11/16 5/16 2 B-2
5V 1250 03 3 3020 3 75 - 2 3/8 2-3/8 A-2
5V 1250 04 4 3020 3 75 - 2 1-1/16 3-1/16 A-2
5V 1250 05 12.40 12.50 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-2
5V 1250 06 6 3535 3-1/2 90 - 3-1/2 15/16 4-7/16 A-2
5V 1250 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-1
5V 1250 10 10 4040 4 100 3/4 4 2-7/16 7-3/16 A-2
5V 1320 02 2 3020 3 75 - 1-11/16 5/16 2 B-3
5V 1320 03 3 3020 3 75 - 2 3/8 2-3/8 A-2
5V 1320 04 4 3020 3 75 - 2 1-1/16 3-1/16 A-3
5V 1320 05 13.10 13.20 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-2
5V 1320 06 6 3535 3-1/2 90 - 3-1/2 15/16 4-7/16 A-2
5V 1320 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-1
5V 1320 10 10 4040 4 100 3/4 4 2-7/16 7-3/16 A-2
5V 1400 02 2 3020 3 75 - 1-11/16 5/16 2 B-3
5V 1400 03 3 3020 3 75 - 2 3/8 2-3/8 A-3
5V 1400 04 4 3535 3-1/2 90 - 3-1/16 7/16 3-1/2 B-3
5V 1400 05 13.90 14.00 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-3
5V 1400 06 6 3535 3-1/2 90 - 3-1/2 15/16 4-7/16 A-2
5V 1400 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-2
5V 1400 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-2
5V 1500 02 2 3020 3 75 - 1-11/16 5/16 2 B-3
5V 1500 03 3 3020 3 75 - 2 3/8 2-3/8 A-3
5V 1500 04 4 3535 3-1/2 90 - 3-1/16 7/16 3-1/2 B-3
5V 1500 05 14.90 15.00 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-3
5V 1500 06 6 4040 4 100 - 4 7/16 4-7/16 A-2
5V 1500 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-2
5V 1500 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-2
5V 1600 02 2 3020 3 75 - 1-11/16 5/16 2 B-3
5V 1600 03 3 3020 3 75 - 2 3/8 2-3/8 A-3
5V 1600 04 4 3535 3-1/2 90 - 3-1/16 7/16 3-1/2 B-3
5V 1600 05 15.90 16.00 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-3
5V 1600 06 6 4040 4 100 - 4 7/16 4-7/16 A-3
5V 1600 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-3
5V 1600 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-2
5V 1870 02 2 3020 3 75 - 2 5/16 1-11/16 C-3
5V 1870 03 3 3020 3 75 - 2 3/8 2-3/8 A-3
5V 1870 04 4 3535 3-1/2 90 - 3-1/16 7/16 3-1/2 B-3
5V 1870 05 18.60 18.70 5 3535 3-1/2 90 - 3-1/2 1/4 3-3/4 A-3
5V 1870 06 6 4040 4 100 - 4 7/16 4-7/16 A-3
5V 1870 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-3
5V 1870 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-2
5V 2120 02 2 3535 3-1/2 90 3/8 3-1/2 1-7/16 1-11/16 C-3
5V 2120 03 3 3535 3-1/2 90 0 2-3/8 1-1/8 3-1/2 B-3
5V 2120 04 4 3535 3-1/2 90 0 3-1/16 7/16 3-1/2 B-3
5V 2120 05 21.10 21.20 5 4040 4 100 0 3-3/4 1/4 4 B-3
5V 2120 06 6 4040 4 100 0 4 7/16 4-7/16 A-3
5V 2120 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-3
5V 2120 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-3
26
- PowerWare®
5V & 5VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
5V 2360 02 2 3535 3-1/2 90 1/4 3-1/2 1-9/16 1-11/16 C-3
5V 2360 03 3 3535 3-1/2 90 0 3-3/8 1-1/8 3-1/2 B-3
5V 2360 04 4 3535 3-1/2 90 0 3-1/16 7/16 3-1/2 B-3
5V 2360 05 23.50 23.60 5 4040 4 100 0 3-3/4 1/4 4 B-3
5V 2360 06 6 4040 4 100 0 4 7/16 4-7/16 A-3
5V 2360 08 8 4040 4 100 1/4 4 1-9/16 5-13/16 A-3
5V 2360 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-3
5V 2800 02 2 3535 3-1/2 90 3/8 3-1/2 1-7/16 1-11/16 C-3
5V 2800 03 3 3535 3-1/2 90 0 2-3/8 1-1/8 3-1/2 B-3
5V 2800 04 4 3535 3-1/2 90 0 3-1/16 7/16 3-1/2 B-3
5V 2800 05 27.90 28.00 5 4040 4 100 0 3-3/4 1/4 4 B-3
5V 2800 06 6 4040 4 100 0 4 7/16 4-7/16 A-3
5V 2800 08 8 4545 4-1/2 110 1/4 4-1/2 1-1/16 5-13/16 A-3
5V 2800 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-3
5V 3150 03 3 3535 3-1/2 11/32 3-1/2 25/32 2-3/8 C-3
5V 3150 04 4 3535 3-1/2 90 0 3-1/16 7/16 3-1/2 B-3
5V 3150 05 5 4040 4 100 0 3-3/4 1/4 4 B-3
5V 3150 06 31.40 31.50 6 4040 4 100 0 4 7/16 4-7/16 A-3
5V 3150 08 8 4545 4-1/2 110 1/4 4-1/2 1-1/16 5-13/16 A-3
5V 3150 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-3
5V 3750 03 3 4040 4 100 1/2 4 1-1/8 2-3/8 C-3
5V 3750 04 4 4040 4 100 0 3-1/16 15/16 4 B-3
5V 3750 05 5 4040 4 100 0 3-3/4 1/4 4 B-3
5V 3750 06 37.40 37.50 6 4545 4-1/2 110 0 4-7/16 1/16 4-1/2 B-3
5V 3750 08 8 4545 4-1/2 110 1/4 4-1/2 1-1/16 5-13/16 A-3
5V 3750 10 10 4545 4-1/2 110 3/4 4-1/2 1-15/16 7-3/16 A-3
5V 5000 03 3 4040 4 100 1/2 4 1-1/8 2-3/8 C-3
5V 5000 04 4 4040 4 100 0 3-1/16 15/16 4 B-3
5V 5000 05 5 4545 4-1/2 110 0 3-3/4 3/4 4-1/2 B-3
5V 5000 06 49.90 50.00 6 4545 4-1/2 110 0 4-7/16 1/16 4-1/2 B-3
5V 5000 08 8 4545 4-1/2 110 1/4 4-1/2 1-1/16 5-13/16 A-3
5V 5000 10 10 5050 5 125 3/4 5 1-7/16 7-3/16 A-3
27
- PowerWare®
8V & 8VX Section Pulleys
E L M L
E F M
PD OD PD OD
TYPE C
TYPE A 1=Solid 2=Web 3=Arm/
Spoke
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
8V 1250 04 4 4040 4 100 0 4 7/8 4-7/8 A-1
8V 1250 05 5 4040 4 100 3/16 4 1-13/16 6 A-1
8V 1250 06 12.3 12.5 6 4040 4 100 1 4 2-1/8 7-1/8 A-1
8V 1250 08 8 4545 4-1/2 110 1-1/2 4-1/2 3-3/8 9-3/8 A-1
8V 1250 12 12 5050 5 125 3-3/16 5 5-11/16 13-7/8 A-1
8V 1320 04 4 4040 4 100 0 4 7/8 4-7/8 A-1
8V 1320 05 5 4040 4 100 3/16 4 1-13/16 6 A-1
8V 1320 06 6 4040 4 100 1 4 2-1/8 7-1/8 A-1
13.0 13.2
8V 1320 08 8 4545 4-1/2 110 1-1/2 4-1/2 3-3/8 9-3/8 A-1
8V 1320 10 10 4545 4-1/2 110 1 4-1/2 6-1/8 11-5/8 A-1
8V 1320 12 12 5050 5 125 3 5 5-7/8 13-7/8 A-1
8V 1400 04 4 4040 4 100 0 4 7/8 4-7/8 A-1
8V 1400 05 5 4040 4 100 3/16 4 1-13/16 6 A-1
8V 1400 06 6 4040 4 100 1 4 2-1/8 7-1/8 A-1
13.8 14.0
8V 1400 08 8 4545 4-1/2 110 1-1/2 4-1/2 3-3/8 9-3/8 A-1
8V 1400 10 10 4545 4-1/2 110 1 4-1/2 6-1/8 11-5/8 A-1
8V 1400 12 12 5050 5 125 3-3/16 5 5-11/16 13-7/8 A-1
8V 1500 04 4 4040 4 100 0 4 7/8 4-7/8 A-1
8V 1500 05 5 4040 4 100 3/16 4 1-13/16 6 A-1
8V 1500 06 6 4545 4-1/2 110 1/2 4-1/2 2-1/8 7-1/8 A-1
14.8 15.0
8V 1500 08 8 4545 4-1/2 110 1-1/2 4-1/2 3-3/8 9-3/8 A-1
8V 1500 10 10 5050 5 125 1 5 5-5/8 11-5/8 A-1
8V 1500 12 12 5050 5 125 1-7/8 5 7 13-7/8 A-1
8V 1600 04 4 4040 4 100 0 4 7/8 4-7/8 A-1
8V 1600 05 5 4040 4 100 1/2 4 1-1/2 6 A-1
8V 1600 06 6 4545 4-1/2 110 1/2 4-1/2 3-3/8 7-1/8 A-2
15.8 16.0
8V 1600 08 8 4545 4-1/2 110 1-1/2 4-1/2 3-3/8 9-3/8 A-2
8V 1600 10 10 5050 5 125 1 5 5-5/8 11-5/8 A-1
8V 1600 12 12 5050 5 125 1-7/8 5 7 13-7/8 A-1
8V 1700 04 4 4040 4 100 0 4 7/8 4-7/8 A-2
8V 1700 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-2
8V 1700 06 6 4545 4-1/2 110 1/2 4-1/2 2-1/8 7-1/8 A-2
16.8 17.0
8V 1700 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-2
8V 1700 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-2
8V 1700 12 12 5050 5 125 3-1/2 5 5-3/8 13-7/8 A-2
28
- PowerWare®
8V & 8VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
8V 1800 04 4 4040 4 100 0 4 7/8 4-7/8 A-2
8V 1800 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-2
8V 1800 06 6 4545 4-1/2 110 1/2 4-1/2 2-1/8 7-1/8 A-2
17.8 18.0
8V 1800 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-2
8V 1800 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-2
8V 1800 12 12 5050 5 125 3-17/32 5 5-11/32 13-7/8 A-2
8V 1900 04 4 4040 4 100 0 4 7/8 4-7/8 A-2
8V 1900 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-2
8V 1900 06 6 4545 4-1/2 110 1/2 4-1/2 2-1/8 7-1/8 A-2
18.8 19.0
8V 1900 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-2
8V 1900 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-2
8V 1900 12 12 5050 5 125 2-1/4 5 6-5/8 13-7/8 A-2
8V 2000 04 4 4545 4-1/2 100 0 4-1/2 3/8 4-7/8 A-2
8V 2000 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-2
8V 2000 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-2
19.8 20.0
8V 2000 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-2
8V 2000 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-2
8V 2000 12 12 5050 5 125 2-1/4 5 6-5/8 13-7/8 A-2
8V 2120 04 4 4545 4-1/2 100 0 4-1/2 3/8 4-7/8 A-3
8V 2120 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-3
8V 2120 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
21.0 21.2
8V 2120 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 2120 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-2
8V 2120 12 12 5050 5 125 2-1/4 5 6-5/8 13-7/8 A-2
8V 2240 04 4 4545 4-1/2 100 0 4-1/2 3/8 4-7/8 A-3
8V 2240 05 5 4545 4-1/2 100 0 4-1/2 1-1/2 6 A-3
8V 2240 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
22.2 22.4
8V 2240 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 2240 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-3
8V 2240 12 12 5050 5 125 2-1/4 5 6-5/8 13-7/8 A-3
8V 2480 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 2480 05 5 5050 5 125 0 5 1 6 A-3
8V 2480 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
24.6 24.8
8V 2480 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 2480 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-3
8V 2480 12 12 5050 5 125 5-3/8 5 3-1/2 13-7/8 A-3
8V 3000 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 3000 05 5 5050 5 125 0 5 1 6 A-3
8V 3000 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
29.8 30.0
8V 3000 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 3000 10 10 5050 5 125 2-1/4 5 4-3/8 11-5/8 A-3
8V 3000 12 12 6050 6 150 4 5 4-7/8 13-7/8 A-3
8V 3550 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 3550 05 5 5050 5 125 0 5 1 6 A-3
8V 3550 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
35.3 35.5
8V 3550 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 3550 10 10 6050 6 150 2-1/4 5 4-3/8 11-5/8 A-3
8V 3550 12 12 6050 6 150 4 5 4-7/8 13-7/8 A-3
29
- PowerWare®
8V & 8VX Section Pulleys
Pitch Outer
Number Bush Max. Bore
Product Diameter Diameter Bush Pulley
of E L M F
Code (PD) (OD) Number Imperial Metric Type
grooves
(Inches) (Inches) (Inches) (mm)
8V 4000 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 4000 05 5 5050 5 125 0 5 1 6 A-3
8V 4000 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
39.8 40.0
8V 4000 08 8 5050 5 125 1 5 3-3/8 9-3/8 A-3
8V 4000 10 10 6050 6 150 2-1/4 5 4-3/8 11-5/8 A-3
8V 4000 12 12 6050 6 150 4 5 4-7/8 13-7/8 A-3
8V 4450 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 4450 05 5 5050 5 125 0 5 1 6 A-3
8V 4450 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
44.3 44.5
8V 4450 08 8 6050 5 125 1 5 3-3/8 9-3/8 A-3
8V 4450 10 10 6050 6 150 2-1/4 5 4-3/8 11-5/8 A-3
8V 4450 12 12 6050 6 150 4 5 4-7/8 13-7/8 A-3
8V 5300 04 4 5050 5 125 0 5 1/8 4-7/8 C-3
8V 5300 05 5 5050 5 125 0 5 1 6 A-3
8V 5300 06 6 5050 5 125 1/2 5 1-5/8 7-1/8 A-3
52.8 53.0
8V 5300 08 8 6050 6 150 1 5 3-3/8 9-3/8 A-3
8V 5300 10 10 6050 6 150 2-1/4 5 4-3/8 11-5/8 A-3
8V 5300 12 12 7060 6 150 5 6 2-7/8 13-7/8 A-3
30
- PowerWare®
Poly-V Pulleys
Poly-V or Ribbed drive is a special construction Belt drive, which can be used with very small pulley
diameters. Poly-V drives help to dampen the noise and vibrations.
Due to reduced pulley size, various applications which require compact drives at high speed are driven
by Poly-V drives.
Some of the common applications include engine drive, machine tools, wood working machines,
health & fitness utility machines, compressors, fans etc.
Poly-V drives help to achieve optimum drive performance and an augmented drive life.
Minimum Groove rt
Cross recommended angle(q) hg dB
Pitch +0.15 2a rb Se
section outer ± 0.25 (p) Minimum ±0.001
degrees -0.00
diameter
0.30 2.0
1.60
H / PH 13 40 0.15 0.58 +0.00 1.04 1.00 +0.5
± 0.03
-0.15 -0.3
0.40 3.0
2.34
J / PJ 20 40 0.20 0.76 +0.00 1.77 1.50 +0.8
± 0.03
-0.15 -0.4
0.50 3.0
3.56
K / PK 40 40 0.25 0.96 +0.00 3.16 3.00 +1.5
± 0.05
-0.15 -0.0
0.40 10.0
4.70
L / PL 75 40 0.40 1.54 +0.00 4.63 4.00 +2.0
± 0.05
-0.15 -1.0
0.75 13.0
9.40
M / PM 180 40 0.75 2.88 +0.00 9.74 7.00 +3.0
± 0.08
-0.25 -1.0
q
dB
a rt
Diameter
Outside
Pitch
rb
p Se
Figure: Standard groove dimensions
31
- PowerWare®
Poly-V (PJ Section Pulleys)
F F
F F R W
Tooling
Tooling
Tooling
Tooling
bore
bore
bore
bore
P O N P O J P O J O N J P
L M L M K M
M
L
L
8-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
8PJ 075 75.0 77.4 8 25 2 1108 25 59 22 - 3 - - - - - - - - - -
8PJ 080 80.0 82.4 8 32 1 1210 25 - 25 - - - - - - - - - - - -
8PJ 085 85.0 87.4 8 32 1 1210 25 - 25 - - - - - - - - - - - -
8PJ 090 90.0 92.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 095 95.0 97.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 100 100.0 102.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 106 106.0 108.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 112 112.0 114.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 118 118.0 120.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 125 125.0 127.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 132 132.0 134.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 140 140.0 142.4 8 40 1 1610 25 - 25 - - - - - - - - - - - -
8PJ 160 160.0 162.4 8 50 1 2012 25 - 32 112 7 - - - - - - - - - -
8PJ 180 180.0 182.4 8 50 1 2012 25 - 32 112 7 - - - - - - - - - -
8PJ 200 200.0 202.4 8 50 8 2012 25 184 32 112 7 - 8.50 - - 8 - - - - -
8PJ 224 224.0 226.4 8 50 8 2012 25 208 32 112 7 - 8.50 - - 8 - - - - -
8PJ 250 250.0 252.4 8 50 8 2012 25 230 32 112 7 - 8.50 - - 8 - - - - -
8PJ 315 315.0 317.4 8 50 4 2012 25 295 32 112 3.5 3.5 - 270 135 12 12 24 24 6 6
8PJ 355 355.0 357.4 8 65 4 2517 25 335 45 124 10 10 - 310 150 12 12 24 24 6 6
8PJ 400 400.0 402.4 8 65 4 2517 25 380 45 124 10 10 - 355 150 12 12 24 24 6 6
32
- PowerWare®
Poly-V (PJ Section Pulleys)
F F
F F R W
Tooling
Tooling
Tooling
Tooling
bore
bore
bore
bore
P O N P O J P O J O N J P
L M L M K M
M
L
L
12-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
12PJ 075 75 77.4 12 32 2 1210 34 60 25 - 9 - - - - - - - - - -
12PJ 080 80 82.4 12 32 2 1210 34 64 25 - 9 - - - - - - - - - -
12PJ 085 85 87.4 12 32 2 1210 34 69 25 - 9 - - - - - - - - - -
12PJ 090 90 92.4 12 40 2 1610 34 74 25 - 9 - - - - - - - - - -
12PJ 095 95 97.4 12 40 2 1610 34 79 25 - 9 - - - - - - - - - -
12PJ 100 100 102.4 12 40 2 1610 34 84 25 - 9 - - - - - - - - - -
12PJ 106 106 108.4 12 40 2 1610 34 90 25 - 9 - - - - - - - - - -
12PJ 112 112 114.4 12 40 2 1610 34 96 25 - 9 - - - - - - - - - -
12PJ 118 118 120.4 12 40 2 1610 34 102 25 - 9 - - - - - - - - - -
12PJ 125 125 127.4 12 50 2 2012 34 109 32 - 2 - - - - - - - - - -
12PJ 132 132 134.4 12 50 2 2012 34 116 32 - 2 - - - - - - - - - -
12PJ 140 140 142.4 12 65 1 2517 34 - 45 124 11 - - - - - - - - - -
12PJ 160 160 162.4 12 65 1 2517 34 - 45 124 11 - - - - - - - - - -
12PJ 180 180 182.4 12 65 1 2517 34 - 45 124 11 - - - - - - - - - -
12PJ 200 200 202.4 12 65 8 2517 34 184 45 124 5.5 5.5 12 - - 10 - - - - -
12PJ 224 224 226.4 12 65 8 2517 34 208 45 124 5.5 5.5 12 - - 10 - - - - -
12PJ 250 250 252.4 12 65 8 2517 34 230 45 124 5.5 5.5 12 - - 10 - - - - -
12PJ 315 315 317.4 12 65 4 2517 34 295 45 124 5.5 5.5 - 270 150 14 12 28 24 7 6
12PJ 355 355 357.4 12 65 4 2517 34 335 45 124 5.5 5.5 - 310 150 14 12 28 24 7 6
12PJ 400 400 402.4 12 65 4 2517 34 380 45 124 5.5 5.5 - 355 150 18 16 36 32 9 8
33
- PowerWare®
Poly-V (PJ Section Pulleys)
F F
F F R W
Tooling
Tooling
Tooling
Tooling
bore
bore
bore
bore
P O N P O J P O J O N J P
L M L M K M
M
L
L
16-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
16PJ 075 75 77.4 16 32 2 1210 44 59 25 - 19 - - - - - - - - - -
16PJ 080 80 92.4 16 32 2 1210 44 64 25 - 19 - - - - - - - - - -
16PJ 085 85 87.4 16 40 2 1610 44 70 25 - 19 - - - - - - - - - -
16PJ 090 90 92.4 16 40 2 1610 44 74 25 - 19 - - - - - - - - - -
16PJ 095 95 97.4 16 40 2 1610 44 79 25 - 19 - - - - - - - - - -
16PJ 100 100 102.4 16 40 2 1610 44 84 25 - 19 - - - - - - - - - -
16PJ 106 106 1084 16 40 2 1610 44 90 25 - 19 - - - - - - - - - -
16PJ 112 112 114.4 16 40 2 1610 44 96 25 - 19 - - - - - - - - - -
16PJ 118 118 120.4 16 50 2 2012 44 102 32 - 12 - - - - - - - - - -
16PJ 125 125 127.4 16 50 2 2012 44 109 32 - 12 - - - - - - - - - -
16PJ 132 132 134.4 16 50 2 2012 44 116 32 124 12 - - - - - - - - - -
16PJ 140 140 142.4 16 65 1 2517 44 - 45 124 1 - - - - - - - - - -
16PJ 160 160 162.4 16 65 1 2517 44 - 45 124 1 - - - - - - - - - -
16PJ 180 180 182.4 16 65 1 2517 44 - 45 124 1 - - - - - - - - - -
16PJ 200 200 202.4 16 65 8 2517 44 184 45 124 1 - 14 - - 15 - - - - -
16PJ 224 224 226.4 16 65 8 2517 44 208 45 124 1 - 14 - - 15 - - - - -
16PJ 250 250 252.4 16 65 8 2517 44 230 45 124 1 - 14 - - 15 - - - - -
16PJ 315 315 317.4 16 65 4 2517 44 295 45 124 1 - - 270 150 18 16 36 32 9 8
16PJ 355 355 357.4 16 65 4 2517 44 335 45 124 1 - - 310 150 18 16 36 32 9 8
16PJ 400 400 402.4 16 80 4 3020 44 380 51 159 4.5 4.5 - 355 185 20 18 40 36 10 9
34
- PowerWare®
Poly-V (PJ Section Pulleys)
F
L R W
F
X
Tooling bore
Tooling bore
Tooling bore
P O J OS NQJ P O J P
K M
L M L M M
L
20-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
20PJ 075 75 77.4 20 32 2 1210 53 59 25 - 28 - - - - - - - - - -
20PJ 080 80 82.4 20 32 2 1210 53 64 25 - 28 - - - - - - - - - -
20PJ 085 85 87.4 20 40 2 161.0 53 70 25 - 28 - - - - - - - - - -
20PJ 090 90 92.4 20 40 2 1610 53 74 25 - 28 - - - - - - - - - -
20PJ 095 95 97.4 20 40 2 1610 53 79 25 - 28 - - - - - - - - - -
20PJ 100 100 102.4 20 40 2 1610 53 84 25 - 28 - - - - - - - - - -
20PJ 106 106 108.4 20 40 2 1610 53 90 25 - 28 - - - - - - - - - -
20PJ 112 112 114.4 20 40 2 1610 53 96 25 - 28 - - - - - - - - - -
20PJ 118 118 120.4 20 50 2 2012 53 102 32 - 21 - - - - - - - - - -
20PJ 125 125 127.4 20 50 2 2012 53 109 32 - 21 - - - - - - - - - -
20PJ 132 132 134.4 20 50 2 2012 53 116 32 - 21 - - - - - - - - - -
20PJ 140 140 142.4 20 65 2 2517 53 124 45 - 8 - - - - - - - - - -
20PJ 160 160 162.4 20 65 2 2517 53 144 45 - 8 - - - - - - - - - -
20PJ 180 180 182.4 20 65 2 2517 53 164 45 - 8 - - - - - - - - - -
20PJ 200 200 202.4 20 65 7 2517 53 184 45 124 4 4 15 - - 22 - - - - -
20PJ 224 224 226.4 20 65 7 2517 53 208 45 124 4 4 15 - - 22 - - - - -
20PJ 250 250 252.4 20 65 7 2517 53 230 45 124 4 4 15 - - 22 - - - - -
20PJ 315 315 317.4 20 65 5 2517 53 295 45 124 4 4 - 270 150 18 16 36 32 9 8
20PJ 355 355 357.4 20 65 5 2517 53 335 45 124 4 4 - 310 150 18 16 36 32 9 8
20PJ 400 400 402.4 20 80 5 3020 53 380 51 159 1 1 - 355 185 20 18 40 36 10 9
35
- PowerWare®
Poly-V (PL Section Pulleys)
F F
F F F
R W
Tooling bore
Tooling bore
Tooling bore
Tooling bore
PO N PO Tooling bore J PO J PO J O NJ P
L M L M L M K M
M
L
L
8-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
8PL 075 75 81 8 32 6 1210 44 45 25 - - 19 - - - - - - - - -
8PL 080 80 86 8 32 6 1210 44 50 25 - - 19 - - - - - - - - -
8PL 085 85 91 8 40 6 1610 44 55 25 - - 19 - - - - - - - - -
8PL 090 90 96 8 40 6 1610 44 60 25 - - 19 - - - - - - - - -
8PL 095 95 101 8 40 6 1610 44 65 25 - - 19 - - - - - - - - -
8PL 100 100 106 8 40 2 1610 44 70 25 - 19 - - - - - - - - - -
8PL 106 106 112 8 40 2 1610 44 76 25 - 19 - - - - - - - - - -
8PL 112 112 118 8 40 2 1610 44 82 25 - 19 - - - - - - - - - -
8PL 118 118 124 8 40 2 1610 44 88 25 - 19 - - - - - - - - - -
8PL 125 125 131 8 50 2 2012 44 95 32 - 12 - - - - - - - - - -
8PL 132 132 138 8 50 2 2012 44 102 32 - 12 - - - - - - - - - -
8PL 140 140 146 8 65 1 2517 44 - 45 124 1 - - - - - - - - - -
8PL 160 160 166 8 65 1 2517 44 - 45 124 1 - - - - - - - - - -
8PL 180 180 186 8 65 1 2517 44 - 45 124 1 - - - - - - - - - -
8PL 200 200 206 8 65 1 2517 44 - 45 124 1 - - - - - - - - - -
8PL 224 224 230 8 65 8 2517 44 194 45 124 0.5 0.5 14 - - 15 - - - - -
8PL 250 250 256 8 65 8 2517 44 220 45 124 0.5 0.5 14 - - 15 - - - - -
8PL 315 315 321 8 80 8 3020 44 285 51 159 3.5 3.5 14 - - 15 - - - - -
8PL 355 355 361 8 80 4 3020 44 325 51 159 3.5 3.5 - 300 185 18 16 36 32 9 8
8PL 400 400 406 8 80 4 3020 44 370 51 159 3.5 3.5 - 345 185 20 18 40 36 10 9
8PL 500 500 506 8 80 4 3020 44 470 51 159 3.5 3.5 - 445 185 22 20 44 40 11 10
8PL 560 560 566 8 80 4 3020 44 530 51 159 3.5 3.5 - 505 185 24 22 48 44 12 11
8PL 630 630 636 8 80 4 3020 44 590 51 159 3.5 3.5 - 565 185 26 24 52 48 13 12
8PL 800 800 806 8 80 4 3020 44 760 51 159 3.5 3.5 - 735 185 28 26 56 52 14 13
36
- PowerWare®
Poly-V (PL Section Pulleys)
F
F L F R W
F X
W
Tooling bore
Tooling bore
Tooling bore
Tooling bore
Tooling bore
PO J PO J OS N QJ P P O J O N J P
K L M
L M L M L M
M L M
12-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
12PL 075 75 81 12 32 6 1215 63 45 38 - - 25 - - - - - - - - -
12PL 080 80 86 12 32 6 1215 63 50 38 - - 25 - - - - - - - - -
12PL 085 85 91 12 40 6 1615 63 55 38 - - 25 - - - - - - - - -
12PL 090 90 96 12 40 6 1615 63 60 38 - - 25 - - - - - - - - -
12PL 095 95 101 12 40 6 1615 63 65 38 - - 25 - - - - - - - - -
12PL 100 100 106 12 40 2 1615 63 70 38 - 25 - - - - - - - - - -
12PL 106 106 1120 12 40 2 1615 63 76 38 - 25 - - - - - - - - - -
12PL 112 112 118 12 40 2 1615 63 82 38 - 25 - - - - - - - - - -
12PL 118 118 124 12 40 2 1615 63 88 38 - 25 - - - - - - - - - -
12PL 125 125 131 12 65 2 2517 63 98 45 - 18 - - - - - - - - - -
12PL 132 132 138 12 65 2 2517 63 102 45 - 18 - - - - - - - - - -
12PL 140 140 146 12 65 2 2517 63 110 45 - 18 - - - - - - - - - -
12PL 160 160 166 12 65 2 2517 63 130 45 - 18 - - - - - - - - - -
12PL 180 180 186 12 65 2 2517 63 150 45 - 18 - - - - - - - - - -
12PL 200 200 206 12 80 2 3020 63 170 51 - 12 - - - - - - - - - -
12PL 224 224 230 12 80 2 3020 63 194 51 - 12 - - - - - - - - - -
12PL 250 250 256 12 80 7 3020 63 220 51 159 6 6 21 - - 20 - - - - -
12PL 315 315 321 12 80 7 3020 63 285 51 159 6 6 21 - - 20 - - - - -
12PL 355 355 361 12 80 5 3020 63 325 51 159 6 6 - 300 185 20 18 40 36 10 9
12PL 400 400 406 12 105 4 3525 63 370 65 178 1 1 - 345 200 22 20 44 4 11 10
12PL 500 500 506 12 105 4 3525 63 470 65 178 1 1 - 445 200 24 22 48 44 12 11
12PL 560 560 566 12 105 4 3525 63 530 65 178 1 1 - 505 200 26 24 52 48 13 12
12PL 630 630 636 12 105 4 3525 63 590 65 178 1 1 - 565 200 28 26 56 52 14 13
12PL 800 800 806 12 105 4 3525 63 760 65 178 1 1 - 735 200 30 28 60 56 15 14
37
- PowerWare®
Poly-V (PL Section Pulleys)
F
F F L F R W
X
W
Tooling bore
Tooling bore
Tooling bore
Tooling bore
Tooling bore
P O J O P J OS NQJ P P O J O N J P
K L M
L M L M
K L M M L M
16-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
16PL 085 85 91 16 40 6 1615 81.5 55 38 - - 43.5 - - - - - - - - -
16PL 090 90 96 16 40 6 1615 81.5 60 38 - - 435 - - - - - - - - -
16PL 095 95 101 16 40 6 1615 81.5 65 38 - - 43.5 - - - - - - - - -
16PL 100 100 106 16 40 6 1615 81.5 70 38 - - 43.5 - - - - - - - - -
16PL 106 106 112 16 50 6 2012 81.5 76 32 - - 49.5 - - - - - - - - -
16PL 112 112 118 16 50 2 2012 81.5 83 32 - 49.5 - - - - - - - - - -
16PL 118 118 124 16 50 2 2012 81.5 88 32 - 49.5 - - - - - - - - - -
16PL 125 125 1310 16 65 2 2517 81.5 98 45 - 36.5 - - - - - - - - - -
16PL 132 132 138 16 65 2 2517 81.5 102 45 - 36.5 - - - - - - - - - -
16PL 140 140 146 16 65 2 2517 81.5 110 45 - 36.5 - - - - - - - - - -
16PL 160 160 166 16 65 3 2517 81.5 130 45 - 18.5 18 - - - - - - - - -
16PL 100 100 186 16 80 3 3020 81.5 150 51 - 15.5 15 - - - - - - - - -
16PL 200 200 206 16 80 3 3020 81.5 170 51 - 15.5 15 - - - - - - - - -
16PL 224 224 230 16 80 3 3020 81.5 194 51 - 15.5 15 - - - - - - - - -
16PL 250 250 256 16 80 7 3020 81.5 220 51 159 15.5 15 28 - - 25 - - - - -
16PL 315 315 321 16 105 7 3525 81.5 285 65 178 8.5 8 26 - - 30 - - - - -
16PL 355 355 361 16 105 5 3525 81.5 325 65 178 8.5 8 - 300 200 22 20 44 40 11 10
16PL 400 400 406 16 105 5 3525 81.5 370 65 178 8.5 8 - 345 200 24 22 48 44 12 11
16PL 500 500 506 16 105 5 3525 81.5 470 65 178 8.5 8 - 445 200 26 24 52 48 13 12
16PL 560 560 566 16 105 5 3525 81.5 530 65 178 8.5 8 - 505 200 28 26 56 52 14 13
16PL 630 630 636 16 105 5 3525 81.5 590 65 170 8.5 8 - 565 200 30 28 60 56 15 14
16PL 800 800 806 16 120 5 4030 81.5 760 76 216 3.0 2.5 - 735 240 32 30 64 60 16 15
38
- PowerWare®
Poly-V (PL Section Pulleys)
F
F F L R W
F X
W
Tooling bore
Tooling bore
Tooling bore
Tooling bore
Tooling
bore
PO J O P J PO J OS NQ J P O N J P
K L M
L M L M L
K L M M M
20-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore F J L N M K R Q S W X Y Z R1 R2
Type Size
(mm) (mm) (mm)
20PL 106 106 112 20 50 3 2012 100 83 32 - 34 34 - - - - - - - - -
20PL 112 112 118 20 50 3 2012 100 83 32 - 34 34 - - - - - - - - -
20PL 118 118 124 20 50 3 2012 100 88 32 - 34 34 - - - - - - - - -
20PL 125 125 131 20 65 3 2517 100 98 45 - 27.5 27.5 - - - - - - - - -
20PL 132 132 138 20 65 3 2517 100 102 45 - 27.5 27.5 - - - - - - - - -
20PL 140 140 146 20 65 3 2517 100 110 45 - 27.5 27.5 - - - - - - - - -
20PL 160 160 166 20 65 3 2517 100 130 45 - 27.5 27.5 - - - - - - - - -
20PL 180 180 186 20 80 3 3020 100 150 51 - 24.5 24.5 - - - - - - - - -
20PL 200 200 206 20 80 2 3020 100 170 51 - 49 - - - - - - - - - -
20PL 224 224 230 20 80 2 3020 100 194 51 - 49 - - - - - - - - - -
20PL 250 250 256 20 80 7 3020 100 220 51 159 24.5 24.5 37 - - 25 - - - - -
20PL 315 315 321 20 105 7 3535 100 285 89 178 5.5 5.5 32 - - 35 - - - - -
20PL 355 355 361 20 105 5 3535 100 325 89 178 5.5 5.5 - 300 200 24 22 48 44 12 11
20PL 400 400 406 20 105 5 3535 100 370 89 178 5.5 5.5 - 345 200 26 24 52 48 13 12
20PL 500 500 506 20 105 5 3535 100 470 89 178 5.5 5.5 - 445 200 28 26 56 52 14 13
20PL 560 560 566 20 105 5 3535 100 530 89 178 5.5 5.5 - 505 200 30 28 60 56 15 14
20PL 630 630 636 20 105 5 3535 100 590 89 178 5.5 5.5 - 565 200 32 30 64 60 16 15
20PL 800 800 806 20 120 4 4040 100 760 102 216 0.5 0.5 - 735 240 34 32 68 64 17 16
39
- PowerWare®
Poly-V (PM Section Pulleys)
F
F L R W
F X
W
Tooling bore
Tooling bore
Tooling bore
Tooling bore
PO J PO J OS NQJ P O N J P
K L M
L M L M L
M M
8-grooves
Part Outer Pitch No. of Tooling Pulley Bush
Number Dia (O) Dia (P) Grooves Bore Type Size F J L N M K R Q S W X Y Z R1 R2
(mm) (mm) (mm)
8PM 180 180 188 8 80 2 3020 81 140 51 - 30 - - - - - - - - - -
8PM 200 200 208 8 80 2 3020 81 160 51 - 30 - - - - - - - - - -
8PM 224 224 232 8 80 2 3020 81 184 51 - 30 - - - - - - - - - -
8PM 250 250 258 8 80 2 3020 81 210 51 - 30 - - - - - - - - - -
8PM 315 315 323 8 105 7 3525 81 275 65 178 8.0 8.0 25 - - 30 - - - - -
8PM 355 355 363 8 105 7 3525 81 315 65 178 8.0 8.0 25 - - 30 - - - - -
8PM 375 375 383 8 105 5 3525 81 335 65 178 8.0 8.0 - 310 200 24 22 48 44 12 11
8PM 400 400 408 8 105 5 3525 81 360 65 178 8.0 8.0 - 335 200 24 22 48 44 12 11
8PM 425 425 433 8 105 5 3525 81 385 65 178 8.0 8.0 - 360 200 24 22 48 44 12 11
8PM 450 450 458 8 105 5 3525 81 410 65 178 8.0 8.0 - 385 200 25 23 50 46 12 11
8PM 475 475 483 8 105 5 3525 81 435 65 178 8.0 8.0 - 410 200 25 23 50 46 12 11
8PM 500 500 508 8 105 5 3525 81 460 65 178 8.0 8.0 - 435 200 26 24 52 48 13 12
8PM 530 530 538 8 120 5 4030 81 490 76 216 2.5 2.5 - 465 240 28 26 56 52 14 13
8PM 560 560 568 8 120 5 4030 81 520 76 216 2.5 2.5 - 495 240 28 26 56 52 14 13
8PM 630 630 638 8 120 5 4030 81 590 76 216 2.5 2.5 - 565 240 30 28 60 56 15 14
8PM 800 800 808 8 120 5 4030 81 750 76 216 2.5 2.5 - 725 240 32 30 64 60 16 15
8PM 1000 1000 1008 8 130 4 4535 81 950 89 242 4.0 4.0 - 925 265 36 34 72 68 18 17
40
- PowerWare®
Poly-V (PM Section Pulleys)
F
F L R W
X
Tooling bore
Tooling bore
Tooling bore
O P J OS NQ J P O N J P
K L M
K L M M L M
12-grooves
Outer Pitch Pull
Part No. of Tooling
Number Dia (O) Dia (P) Grooves Bore -ey Bush F J L N M K R Q S W X Y Z R1 R2
(mm) (mm) (mm) Type Size
12PM 180 180 188 12 80 3 3020 118.5 140 51 - 37.5 30 - - - - - - - - -
12PM 200 200 208 12 105 3 3535 118.5 160 89 - 15.0 14.5 - - - - - - - - -
12PM 224 224 232 12 105 3 3535 118.5 184 39 - 15.0 14.5 - - - - - - - - -
12PM 250 250 258 12 105 3 3535 118.5 210 89 - 15.0 14.5 - - - - - - - - -
12PM 315 315 323 12 105 7 3535 118.5 275 89 178 15.0 14.5 42 - - 35 - - - - -
12PM 355 355 363 12 105 7 3535 118.5 315 89 178 15.0 14.5 42 - - 35 - - - - -
12PM 375 375 383 12 105 5 3535 118.5 335 89 178 15.0 14.5 - 310 200 24 22 48 44 12 11
12PM 400 400 408 12 105 5 3535 118.5 366 89 178 15.0 14.5 - 335 200 26 24 52 48 13 12
12PM 425 425 433 12 120 5 4040 118.5 385 102 216 8.5 8 - 360 240 26 24 52 48 13 12
12PM 450 450 458 12 120 5 4040 118.5 410 102 216 8.5 8 - 385 240 26 24 52 48 13 12
12PM 475 475 483 12 120 5 4040 118.5 435 102 216 8.5 8 - 410 240 28 26 56 52 14 13
12PM 500 500 508 12 120 5 4040 118.5 460 102 216 8.5 8 - 435 240 28 26 56 52 14 13
12PM 530 530 538 12 130 5 4545 118.5 490 114 242 2.5 2 - 465 265 28 26 56 52 14 13
12PM 560 560 560 12 130 5 4545 118.5 520 114 242 2.5 2 - 495 265 28 26 56 52 14 13
12PM 630 630 638 12 145 5 5040 118.5 590 102 267 8.7 8.3 - 565 290 30 28 60 56 15 14
12PM 800 800 808 12 145 5 5040 118.5 750 102 267 8.7 8.3 - 725 290 36 34 72 68 18 17
12PM 1000 1000 1008 12 145 5 5040 118.5 950 102 267 8.7 8.3 - 925 290 38 36 76 72 19 18
41
- PowerWare®
Poly-V (PM Section Pulleys)
F
F L R W
X
Tooling bore
Tooling bore
Tooling bore
O P J OS NQ J P O N J P
K L M
K L M M L M
16-grooves
Outer Pitch Pull
Part No. of Tooling
Number Dia (O) Dia (P) Grooves Bore -ey Bush F J L N M K R Q S W X Y Z R1 R2
(mm) (mm) (mm) Type Size
16PM 180 180 188 16 80 3 3030 156 140 76 - 48 32 - - - - - - - - -
16PM 200 200 208 16 105 3 3535 156 160 89 - 35 32 - - - - - - - - -
16PM 224 224 232 16 105 3 3535 156 184 89 - 35 32 - - - - - - - - -
16PM 250 250 258 16 105 3 3535 156 210 89 - 35 32 - - - - - - - - -
16PM 315 315 323 16 105 7 3535 156 275 89 178 35 32 60 - - 35 - - - - -
16PM 355 355 363 16 105 7 3535 156 315 89 178 35 32 60 - - 35 - - - - -
16PM 375 375 383 16 120 7 4040 156 335 102 216 27 27 58 - - 40 - - - - -
16PM 400 400 408 16 120 7 4040 156 360 102 216 27 27 58 - - 40 - - - - -
16PM 425 425 433 16 130 7 4545 156 385 114 242 21 21 58 - - 40 - - - - -
16PM 450 450 458 16 130 5 4545 156 410 114 242 21 21 - 385 265 28 26 56 52 14 13
16PM 475 475 483 16 130 5 4545 156 435 114 242 21 21 - 410 265 30 28 60 56 15 14
16PM 500 500 508 16 130 5 4545 156 460 114 242 21 21 - 435 265 30 28 60 56 15 14
16PM 530 530 538 16 145 5 5050 156 490 127 267 15 14 - 465 290 32 30 64 60 16 15
16PM 560 560 568 16 145 5 5050 156 520 127 267 15 14 - 495 290 32 30 64 60 16 15
16PM 630 630 638 16 145 5 5050 156 590 127 267 15 14 - 565 290 34 32 68 64 17 16
16PM 800 800 808 16 145 5 5050 156 750 127 267 15 14 - 725 290 38 36 76 72 19 18
16PM 1000 1000 1008 16 145 5 5050 156 950 127 267 15 14 - 925 290 40 38 80 76 20 19
42
- PowerWare®
Poly-V (PM Section Pulleys)
F
F L R W
X
Tooling bore
Tooling bore
Tooling bore
O P J OS NQ J P O N J P
K L M
K L M M L M
20-grooves
Outer Pitch Pull
Part No. of Tooling
Number Dia (O) Dia (P) Grooves Bore -ey Bush F J L N M K R Q S W X Y Z R1 R2
(mm) (mm) (mm) Type Size
20PM 180 180 188 20 80 3 3030 194 140 76 - 80 38 - - - - - - - - -
20PM 200 200 208 20 105 3 3535 194 160 89 - 60 45 - - - - - - - - -
20PM 224 224 232 20 105 3 3535 194 184 89 - 60 45 - - - - - - - - -
20PM 250 250 258 20 105 3 3535 194 210 89 - 60 45 - - - - - - - - -
20PM 315 315 323 20 120 3 4040 194 275 102 - 46 46 - - - - - - - - -
20PM 355 355 363 20 120 7 4040 194 315 102 216 46 46 77 - - 40 - - - - -
20PM 375 375 383 20 130 7 4545 194 335 114 242 40 40 77 - - 40 - - - - -
20PM 400 400 408 20 130 7 4545 194 360 114 242 40 40 77 - - 40 - - - - -
20PM 425 425 433 20 145 7 5050 194 385 127 267 34 33 72 - - 50 - - - - -
20PM 450 450 458 20 145 7 5050 194 410 127 267 34 33 72 - - 50 - - - - -
20PM 475 475 483 20 145 5 5050 194 435 127 267 34 33 - 410 290 32 30 64 60 16 15
20PM 500 500 508 20 145 5 5050 194 460 127 267 34 33 - 435 290 32 30 64 60 16 15
20PM 530 530 538 20 145 5 5050 194 490 127 267 34 33 - 465 290 34 32 68 64 17 16
20PM 560 560 568 20 145 5 5050 194 520 127 267 34 33 - 495 290 34 32 68 64 17 16
20PM 630 630 638 20 145 5 5050 194 590 127 267 34 33 - 565 290 36 34 72 68 18 17
20PM 800 800 808 20 145 5 5050 194 750 127 267 34 33 - 725 290 40 38 90 76 20 19
20PM 1000 1000 1008 20 145 5 5050 194 950 127 267 34 33 - 925 290 44 42 88 84 22 21
43
- PowerWare®
L050- 1/2” (13mm) wide Belts
B E
B
G A G A G C
D
F
D E F
E E
Type 3F Type 9
Type 1F
44
- PowerWare®
L075- 3/4” (19mm) wide Belts
B E
B
B
G A G A
C A G C
D
F D E
D E F
E
Type 4F E
Type 3F Type 9
Type 1F
45
- PowerWare®
L100-1” (25mm) wide Belts
B
B E
B
G A
C A G C G C
F D E
D E F
E
E
Type 4F D F
Type-7 Type 9
Type 1F
46
- PowerWare®
H100 - 3/4" (19mm) & 1” (25mm) wide Belts
B E
B
G C
C A G C A
D E
D E F
Type 4F E
D F
Type 9
Type-7F
47
- PowerWare®
H150- 1 1/2" (38mm) wide Belts
B B
C A G C A G C
D E
E E
Type 4F D F D F
Type-7F Type-7
48
- PowerWare®
H200 - 2" (51mm) wide Belts
B B B
E
B
G A
C A G C A G C G C
F D E
D E F
E E
E Type 4F D F D F
Type 1F Type 9
Type-7F Type-7
49
- PowerWare®
H300 -3" (76mm) wide Belts
B B B
G A
C A G C A G C
F D E
E E
E Type 4F D F D F
Type 1F Type-7F Type-7
50
B B E
G A
G
G A
G C
F
E
F
Type-2F
E
Type-11
F
D E F
E
Type 9
Type 1F
51
STP-28-5M-15 44.56 28 43.42 PB 19.0 3/4 1F 49.0 22.0 - - 30.0 8.0 31.0
STP-48-5M-15 76.39 48 75.25 1210 32.0 1 1/4 2F 79.0 22.0 - - 25.0 3.0 59.0
STP-56-5M-15 89.13 56 87.98 1210 32.0 1 1/4 2F 95.0 22.0 - - 25.0 3.0 75.0
STP-64-5M-15 101.86 64 100.72 1210 32.0 1 1/4 2F 106.0 22.0 - - 25.0 3.0 80.0
STP-72-6M-15 114.59 72 113.45 1210 42.0 1 5/8 2F - 22.0 - - 25.0 3.0 92.0
STP-80-.5M-15 127.32 80 126.18 1610 42.0 1 5/8 11 - 22.0 - - 25.0 3.0 92.0
STP-90-5M-15 143.24 90 142.1 1610 42.0 1 5/8 11 - 22.0 - - 25.0 3.0 92.0
STP-112-5M-15 178.25 112 177.11 2012 50.0 2 11 - 20.0 - - 32.0 12.0 110.0
STP-136-5M-15 216.45 136 215.31 2012 50.0 2 9 - 20.0 199.0 6.0 32.0 6.0 106.0
STP-160-5M-15 238.73 150 237.59 2012 50.0 2 9 - 20.0 222.0 6.0 32.0 6.0 106.0
- PowerWare®
B
B
G A G
C A
F
F
E
Type-2F E
D E
Type-11
Type 4F
52
STP-22-8M-20 56.02 22 54.65 1008 25.0 1 4F 62.0 26.0 41.0 4.0 22.0 - -
STP-24-8M-20 61.12 24 59.75 1008 28.0 1 1/8 4F 70.0 26.0 44.0 4.0 22.0 - -
STP-26-8M-20 66.21 26 64.84 1008 28.0 1 1/8 4F 75.0 26.0 44.0 4.0 22.0 - -
STP-28-3M-20 71.30 28 70.08 1108 28.0 1 1/8 4F 79.0 26.0 50.0 4.0 22.0 - -
STP-30-3M-20 76.39 30 75.13 1108 28.0 1 1/8 4F 86.0 26.0 55.0 4.0 22.0 - -
STP-32-8M-20 81.49 32 80.16 1610 42.0 1 5/8 2F 90.0 26.0 - - 26.0 - -
STP-34-8M-20 86.58 34 85.22 1610 42.0 1 5/8 2F 95.0 26.0 - - 26.0 - -
8mm Pitch High Torque (HTD) Pulley (20mm wide Belts)
G A G
C A G C G C
F
F
E
Type-2F E
D E
D F
Type-11 D E F
Type 4F E
Type 9 Type-10
STP-22-8M-30 56.02 22 54.65 1008 25.0 1 4F 62.0 36.0 41.0 14.0 22.0 - -
53
STP-24-8M-30 61.12 24 59.75 1008 28.0 1 1/8 4F 70.0 36.0 44.0 14.0 22.0 - -
STP-26-8M-30 66.21 26 64.84 1008 28.0 1 1/8 4F 75.0 36.0 44.0 14.0 22.0 - -
STP-28-8M-30 71.30 28 70.08 1210 32.0 1 1/4 4F 79.0 36.0 55.0 11.0 25.0 - -
STP-30-8M-30 76.39 30 75.13 1610 42.0 1 1/8 2F 86.0 36.0 - - 38.0 2.0 66.0
STP-32-8M-30 81.49 32 80.16 1610 42.0 1 5/8 2F 90.0 36.0 - - 38.0 2.0 66.0
STP-34-8M-30 86.58 34 85.22 1610 42.0 1 5/8 2F 95.0 36.0 - - 38.0 2.0 70.0
STP-36-8M-30 91.67 36 90.30 1610 42.0 1 5/8 2F 98.0 36.0 - - 38.0 2.0 70.0
8mm pitch High Torque (HTD) Pulley (30mm wide Belts)
STP-38-8M-30 96.77 38 95.39 1610 42.0 1 5/8 2F 106.0 36.0 - - 38.0 2.0 75.0
STP-40-8M-30 101.86 40 100.49 1610 42.0 1 5/8 2F 111.0 36.0 - - 38.0 2.0 75.0
STP-44-8M-30 112.05 44 110.67 2012 50.0 2 4F 119.0 36.0 80.0 4.0 32.0 - -
STP-48-8M-30 122.23 48 120.86 2012 50.0 2 4F 135.0 36.0 90.0 4.0 32.0 - -
STP-56-8M-30 142.60 56 141.23 2012 50.0 2 4F 151.0 36.0 110.0 4.0 32.0 - -
STP-64-8M-30 162.97 64 161.60 2517 60.0 2 1/2 2F 168.0 36.0 - - 45.0 9.0 124.0
STP-72-8M-30 183.35 72 181.97 2517 60.0 2 1/2 11 - 36.0 - - 45.0 9.0 124.0
STP-80-8M-30 203.72 80 202.35 2517 60.0 2 1/2 11 - 36.0 - - 45.0 9.0 124.0
STP-90-8M-30 229.18 90 227.81 2517 60.0 2 1/2 9 - 36.0 198.0 4.5 45.0 4.5 124.0
STP-112-8M-30 285.21 112 283.83 2517 60.0 2 1/2 9 - 36.0 254.0 4.5 45.0 4.5 124.0
STP-144-8M-30 366.59 144 365.32 2517 60.0 2 1/2 10 - 36.0 335.0 4.5 45.0 4.5 124.0
- PowerWare®
E B
B
B
G A G
C A G C G C
F
F
E
Type-2F E
D E
D F
Type-11 D E F
Type 4F E
Type 9 Type-10
54
STP-28-8M-50 71.30 28 70.08 1210 32.0 1 1/4 4F 79.0 57.0 55.0 32.0 25.0 - -
STP-30-8M-50 76.39 30 75.13 1610 42.0 1 5/8 2F 86.0 57.0 60.0 19.0 38.0 - -
STP-32-8M-50 81.49 32 80.16 1610 42.0 1 5/8 2F 90.0 57.0 60.0 19.0 38.0 - -
STP-34-8M-50 86.58 34 85.22 1610 42.0 1 5/8 2F 95.0 57.0 64.0 19.0 38.0 - -
STP-36-6M-50 91.67 36 90.30 1610 42.0 1 5/8 2F 98.0 57.0 65.0 19.0 38.0 - -
STP-38-8M-50 96.77 38 95.39 1610 42.0 1 5/8 2F 106.0 57.0 74.0 - 38.0 19.0 -
STP-40-8M-50 101.86 40 100.49 1610 50.0 2 2F 111.0 57.0 75.0 25.0 32.0 - -
8mm pitch High Torque (HTD) Pulley (50mm wide Belts)
STP-44-8M-50 112.05 44 110.67 2012 50.0 2 4F 119.0 57.0 88.0 - 32.0 25.0 -
STP-48-8M-50 122.23 48 120.86 2012 50.0 2 4F 135.0 57.0 90.0 - 32.0 25.0 -
STP-56-8M-50 142.60 56 141.23 2012 60.0 2 1/2 4F 151.0 57.0 110.0 - 45.0 12.0 -
STP-64-8M-50 162.97 64 161.60 2517 60.0 2 1/2 2F 168.0 57.0 130.0 - 45.0 12.0 -
STP-72-8M-50 183.35 72 181.97 2517 60.0 2 1/2 11 - 57.0 152.0 - 45.0 12.0 -
STP-80-8M-5O 203.72 80 202.35 2517 75.0 3 11 - 57.0 172.0 - 51.0 6.0 -
STP-90-8M-50 229.18 90 227.81 3020 75.0 3 9 - 57.0 197.0 3.0 51.0 3.0 150.0
STP-112-8M-50 285.21 112 283.83 3020 75.0 3 9 - 57.0 253.0 3.0 51.0 3.0 150.0
STP-144-8M-50 366.59 144 365.32 3020 75.0 3 10 - 57.0 335.0 3.0 51.0 3.0 150.0
STP-168-8M-50 427.81 168 426.44 3525 100.0 4 10 - 57.0 396.0 4.0 65.0 4.0 198.0
STP-192-8M-50 488.92 192 487.55 3525 100.0 4 10 - 57.0 457.0 4.0 65.0 4.0 198.0
- PowerWare®
B
B
B
B
B
C A C A C G C G C
D E F
D E F
D E
Type 6F D E
Type 6 F
E
Type 4F D F
Type 8
Type-7
55
(mm) Teeth (mm) No. (mm) (inches)
STP-34-8M-85 86.58 34 85.22 1615 42.0 1 5/8 4F 95.0 94.0 64.0 56.0 32.0 - -
STP-36-8M-85 91.67 36 90.30 1615 42.0 1 5/8 4F 98.0 94.0 65.0 56.0 38.0 - -
STP-38-8M-85 96.77 38 95.39 1615 42.0 1 5/8 4F 106.0 94.0 65.0 56.0 38.0 - -
STP-40-8M-85 101.86 40 100.49 2012 50.0 2 4F 111.0 94.0 78.0 62.0 32.0 - -
STP-44-8M-55 112.05 44 110.67 2012 50.0 2 4F 119.0 94.0 85.0 62.0 32.0 - -
STP-48-8M-85 122.23 48 120.86 2517 60.0 2 1/2 4F 135.0 94.0 96.0 49.0 45.0 - -
8mm pitch High Torque (HTD) Pulley (85mm wide Belts):
STP-56-3M-85 142.60 56 141.23 2517 60.0 2 1/2 6F 151.0 94.0 111.0 24.5 45.0 24.5 -
STP-64-8M-85 162.97 64 161.60 2517 60.0 2 1/2 6F 168.0 94.0 131.0 24.5 45.0 24.5 -
STP-72-8M-85 183.35 72 181.97 3020 75.0 3 6 - 94.0 152.0 21.5 51.0 21.5 -
STP-80-8M-85 203.72 80 202.35 3020 75.0 3 6 - 94.0 172.0 21.5 51.0 21.5 -
STP-90-8M-85 229.18 90 227.81 3020 75.0 3 6 - 94.0 197.0 21.5 51.0 21.5 -
STP-112-8M-85 285.21 112 283.83 3020 75.0 3 7 - 94.0 253.0 21.5 51.0 21.5 150.0
STP-144-8M-65 366.59 144 365.32 3525 100.0 4 7 - 94.0 335.0 14.5 65.0 14.5 198.0
STP-168-8M-85 427.81 168 426.44 3525 100.0 4 8 - 94.0 396.0 14.5 65.0 14.5 198.0
STP-192-8M-85 488.92 192 487.55 3525 100.0 4 8 - 94.0 457.0 14.5 65.0 14.5 198.0
- PowerWare®
B B
B
B B
C A C A G C A G C G C
E F D E F
Type 5F Type 6F E
D F
E E
D F D F
Type 8
Type-7F Type-7
STP-28-14M-40 124.78 28 122.12 2012 50.0 2 5F 141.0 54.0 88.0 - 32.0 22.0 -
56
STP-29-14M-40 129.23 29 126.57 2012 50.0 2 5F 141.0 54.0 90.0 - 32.0 22.0
STP-30-14M-40 133.69 30 130.99 2012 50.0 2 5F 141.0 54.0 91.0 - 32.0 22.0 -
STP-32-14M-40 142.60 32 139.88 2012 50.0 2 6F 156.0 54.0 100.0 11.0 32.0 11.0 -
STP-34-14M-40 151.51 34 148.79 2517 50.0 2 1/2 6F 156.0 54.0 109.0 4.5 45.0 4.5 -
STP-36-14M-40 160.43 36 157.68 2517 60.0 2 1/2 5F 169.0 54.0 117.0 - 45.0 9.0 -
STP-38-14M-40 169.34 38 166.60 2517 60.0 2 1/2 5F 183.0 54.0 126.0 - 45.0 9.0 -
STP-40-14M-40 178.25 40 175.49 2517 60.0 2 1/2 5F 197.0 54.0 135.0 - 45.0 9.0 -
STP-44-14M-40 196.08 44 193.28 3020 75.0 3 5F 211.0 54.0 153.0 - 51.0 3.0 -
14mm Pitch High Torque (HTD) Pulley (40mm wide Belts):
STP-48-14M-40 213.90 48 211.11 3020 75.0 3 5F 226.0 54.0 171.0 - 51.0 3.0 -
STP-56-14M-40 249.55 56 246.76 3020 75.0 3 7F 267.0 54.0 207.0 1.5 51.0 1.5 144.0
STP-64-14M-40 285.21 64 282.41 3020 75.0 3 8F 297.0 54.0 242.0 1.5 51.0 1.5 159.0
STP-72-14M-40 320.86 72 316.06 3020 75.0 3 8 - 54.0 278.0 1.5 51.0 1.5 159.0
STP-80-14M-40 356.51 80 353.71 3020 75.0 3 7 - 54.0 314.0 1.5 51.0 1.5 159.0
STP-90-14M-40 401.07 90 398.28 3020 75.0 3 8 - 54.0 362.0 1.5 51.0 1.5 159.0
STP-112-14M-40 499.11 112 496.32 3020 75.0 3 8 - 54.0 450.0 1.5 51.0 1.5 159.0
STP-144-14M-40 641.71 144 638.92 3020 75.0 3 8 - 54.0 600.0 1.5 51.0 1.5 159.0
STP-168-14M-40 748.66 168 745.87 3020 75.0 3 8 - 54.0 706.0 1.5 51.0 1.5 159.0
STP-192-14M-40 855.62 192 852.82 3020 75.0 3 8 - 54.0 812.0 1.5 51.0 1.5 159.0
- PowerWare®
B
B
B B
C A C A G C A G C
D E F E F
Type 6F Type 5F E
D F
E
D F
Type 8
Type-7F
57
STP-30-14M-55 133.69 30 130.99 2517 60.0 2 1/2 6F 141.0 70.0 95.0 12.5 45.0 12.5 -
STP-32-14M-55 142.60 32 139.88 2517 60.0 2 1/2 6F 156.0 70.0 100.0 12.5 45.0 12.5 -
STP-34-14M-55 151.51 34 148.79 2517 60.0 2 1/2 6F 156.0 70.0 109.0 12.5 45.0 12.5 -
STP-36-14M-55 160.43 36 157.68 2517 60.0 2 1/2 5F 169.0 70.0 117.0 0.0 45.0 25.0 -
STP-38-14M-55 169.34 38 166.60 2517 60.0 2 1/2 5F 183.0 70.0 126.0 0.0 45.0 25.0 -
STP-40-14M-55 178.25 40 175.49 2517 60.0 2 1/2 6F 197.0 70.0 135.0 12.5 45.0 12.5 -
STP-44-14M-55 196.08 44 193.28 3020 75.0 3 6F 211.0 70.0 153.0 9.5 51.0 9.5 -
14mm Pitch High Torque (HTD) Pulley (55mm wide Belts)
STP-48-14M-55 213.90 48 211.11 3020 75.0 3 6F 226.0 70.0 171.0 9.5 51.0 9.5 -
STP-56-14M-55 249.55 56 246.76 3020 75.0 3 6F 267.0 70.0 207.0 9.5 51.0 9.5 -
STP-64-14M-55 285.21 64 282.41 3020 75.0 3 7F 297.0 70.0 242.0 9.5 51.0 9.5 159.0
STP-72-14M-55 320.86 72 316.06 3020 75.0 3 8 - 70.0 278.0 9.5 51.0 9.5 159.0
STP-80-14M-55 356.51 80 353.71 3020 75.0 3 8 - 70.0 314.0 9.5 51.0 9.5 159.0
STP-90-14M-55 401.07 90 398.28 3020 75.0 3 8 - 70.0 362.0 9.5 51.0 9.5 159.0
STP-112-14M-55 499.11 112 496.32 3020 75.0 3 8 - 70.0 456.0 9.5 51.0 9.5 159.0
STP-144-14M-55 641.71 144 638.92 3020 75.0 3 8 - 70.0 600.0 9.5 51.0 9.5 159.0
STP-168-14M-55 748.66 168 745.87 3020 75.0 3 8 - 70.0 706.0 9.5 51.0 9.5 159.0
STP-192-14M-55 855.62 192 852.82 3020 75.0 3 8 - 70.0 812.0 9.5 51.0 9.5 159.0
- PowerWare®
B B
B
C A G C A G C G C
D E F
Type 6F D E
F
E E
D F D F
Type 8
Type-7F Type-7
STP-28-14M-85 124.78 28 122.12 2517 60.0 2 1/2 6F 141.0 102.0 98.0 27.5 45.0 27.5 -
58
STP-29-14M-85 129.23 29 126.57 2517 60.0 2 1/2 6F 141.0 102.0 98.0 27.5 45.0 27.5
STP-30-14M-85 133.69 30 130.99 2517 60.0 2 1/2 6F 141.0 102.0 100.0 27.5 45.0 27.5 -
STP-32-14M-85 142.60 32 139.88 2517 60.0 2 1/2 6F 156.0 102.0 100.0 27.5 45.0 27.5 -
STP-34-14M-85 151.51 34 148.79 2517 60.0 2 1/2 6F 156.0 102.0 109.0 27.5 45.0 27.5 -
STP-36-14M-85 160.43 36 157.68 3020 75.0 3 6F 169.0 102.0 123.0 27.5 51.0 27.5 -
STP-38-14M-85 169.34 38 166.60 3020 75.0 3 6F 183.0 102.0 126.0 27.5 51.0 27.5 -
STP-40-14M-85 178.25 40 175.49 3020 75.0 3 6F 197.0 102.0 135.0 27.5 51.0 27.5 -
STP-44-14M-85 196.08 44 193.28 3020 75.0 3 6F 211.0 102.0 153.0 27.5 51.0 27.5 -
14mm pitch High Torque (HTD) Pulley (85mm wide Belts)
STP-48-14M-85 213.90 48 211.11 3020 75.0 3 6F 226.0 102.0 171.0 27.5 51.0 27.5 -
STP-56-14M-85 249.55 56 246.76 3525 100.0 4 6F 267.0 102.0 207.0 18.5 65.0 18.5 -
STP-64-14M-85 285.21 64 282.41 3525 100.0 4 7F 297.0 102.0 242.0 18.5 65.0 18.5 -
STP-72-14M-85 320.86 72 316.06 3525 100.0 4 7 - 102.0 278.0 18.5 65.0 18.5 178.0
STP-80-14M-85 356.51 80 353.71 3525 100.0 4 7 - 102.0 314.0 18.5 65.0 18.5 178.0
STP-90-14M-85 401.07 90 398.28 3525 100.0 4 8 - 102.0 358.0 18.5 65.0 18.5 178.0
STP-112-14M-85 499.11 112 496.32 3525 100.0 4 8 - 102.0 456.0 18.5 65.0 18.5 178.0
STP-144-14M-85 641.71 144 638.92 3525 100.0 4 8 - 102.0 600.0 18.5 65.0 18.5 206.0
STP-168-14M-85 748.66 168 745.87 3525 100.0 4 8 - 102.0 706.0 18.5 65.0 18.5 206.0
STP-192-14M-85 855.62 192 852.82 4030 115.0 4 1/2 8 - 102.0 812.0 13.0 76.0 13.0 216.0
- PowerWare®
- PowerWare®
Taper Bush dimensions
Nominal Dia
Taper Taper Face Minimum Maximum
at the Larger
Bush Number Bush Code End of Taper (mm) Width (mm) Bore (mm) Bore (mm)
TLB1008009 to
1008 35.0 22 9 25
TLB1008025
TLB1108009 to
1108 38.0 22 9 28
TLB1108028
TLB1210011 to
1210 47.5 25 11 32
TLB1210032
TLB1215011 to
1215 47.5 38 11 32
TLB1215032
TLB1310014 to
1310 51.0 25 14 35
TLB1310035
TLB1610014 to
1610 57.0 25 14 42
TLB1610042
TLB1615014 to
1615 57.0 38 14 42
TLB1615042
TLB2012014 to
2012 70.0 32 14 50
TLB2012050
TLB2517016 to
2517 85.5 45 16 60
TLB2517060
TLB2525019 to
2525 85.5 65 19 60
TLB2525060
TLB3020025 to
3020 108.0 51 25 75
TLB3020075
TLB3030035 to
3030 108.0 76 35 75
TLB3030075
TLB3525048 to
3525 127.0 65 35 90
TLB3525090
TLB3535035 to
3535 127.0 89 35 90
TLB3535090
4040 TLB4040040 to
146.0 102 40 100
TLB4040100
4545 TLB4545055 to
162.0 114 55 110
TLB4545110
5050 TLB5050070 to
177.5 127 70 125
TLB5050125
59
- PowerWare®
Taper Bush dimensions
Taper Weight approx Bushing Shaft
Bore
Bush Number Lbs Kgs key seat key seat
1/2 to 9/16 0.33 0.15 1/8 x 1/16 1/8 x 1/16
5/8 to 7/8 0.27 0.12 3/16 x 3/32 3/16 x 3/32
1108 15/16 to 1 0.22 0.10 1/4 x 1/8 1/4 x 1/8
1-1/16 to 1-1/8 0.17 0.08 1/4 x 1/16a 1/4 x 1/8
60
- PowerWare®
Metric bores, keyway, keys & screws
Nominal Taper Bore Keyway (mm) Key (mm) Screw Screw
Bush Details
Diameter at Bush Diameter Width Depth Width Depth Tightening
No. (w) (h) (w) (h) Torque(Nm) Qty. Size
Larger End Code (mm)
9 - 10 3 1.4 3 3
TLB1008009 11 - 12 4 1.8 4 4
1008 35 to 13 - 17 5 2.3 5 5 56 2 1/4”
TLB1008025 18 - 22 6 2.8 6 6
23 - 25 8 3.3 8 7
9 - 10 3 1.4 3 3
TLB1108009 11 - 12 4 1.8 4 4
1108 38 to 13 - 17 5 2.3 5 5 56 2 1/4”
TLB1108028 18 - 22 6 2.8 6 6
23 - 28 8 3.3 8 7
11 - 12 4 1.8 4 4
TLB1210011 13 - 17 5 2.3 5 5
1210 47.5 to 18 - 22 6 2.8 6 6 20 2 3/8”
TLB1210032 23 - 30 8 3.3 8 7
31 - 32 10 3.3 10 8
11 - 12 4 1.8 4 4
TLB1215011 13 - 17 5 2.3 5 5
1215 47.5 to 18 - 22 6 2.8 6 6 20 2 3/8”
TLB1215032 23 - 30 8 3.3 8 7
31 - 32 10 3.3 10 8
14 - 17 5 2.3 5 5
TLB1310014
18 - 22 6 2.8 6 6
1310 51 to 20 2 3/8”
23 - 30 8 3.3 8 7
TLB1310035 31 - 35 10 3.3 10 8
14 - 17 5 2.3 5 5
TLB1610014 18 - 22 6 2.8 6 6
1610 57 to 23 - 30 8 3.3 8 7 20 2 3/8”
TLB1610042 31 - 38 10 3.3 10 8
39 - 42 12 3.3 12 8
14 - 17 5 2.3 5 5
TLB1615014 18 - 22 6 2.8 6 6
1615 57 to 23 - 30 8 3.3 8 7 20 2 3/8”
TLB1615042 31 - 38 10 3.3 10 8
39 - 42 12 3.3 12 8
14 - 17 5 2.3 5 5
18 - 22 6 2.8 6 6
TLB2012014
23 - 30 8 3.3 8 7
2012 to 31 2 7/16”
70 31 - 38 10 3.3 10 8
TLB2012050 39 - 44 12 3.3 12 8
45 - 50 14 3.8 14 9
16 - 17 5 2.3 5 5
18 - 22 6 2.8 6 6
23 - 30 8 3.3 8 7
TLB2517016
2517 85.5 31 - 38 10 3.3 10 8
to 48 2 1/2”
39 - 44 12 3.3 12 8
TLB2517060 45 - 50 14 3.8 14 9
51 - 58 16 4.3 16 10
59 - 60 18 4.4 18 11
19 - 22 6 2.8 6 6
23 - 30 8 3.3 8 7
TLB2525019 31 - 38 10 3.3 10 8
2525 85.5 to 39 - 44 12 3.3 12 8 48 2 1/2”
TLB2525060 45 - 50 14 3.8 14 9
51 - 58 16 4.3 16 10
59 - 60 18 4.4 18 11
61
- PowerWare®
Metric bores, keyway, keys & screws
Nominal Taper Bore Keyway (mm) Key (mm) Screw Screw
Bush Details
Diameter at Bush Diameter Width Depth Width Depth Tightening
No. (w) (h) (w) (h) Torque(Nm) Qty. Size
Larger End Code (mm)
25 - 30 8 3.3 8 7
31 - 38 10 3.3 10 8
TLB3020025 39 - 44 12 3.3 12 8
3020 108 to 45 - 50 14 3.8 14 9 90 2 5/8”
TLB3020075 51 - 58 16 4.3 16 10
59 - 65 18 4.4 18 11
66 - 75 20 4.9 20 12
35 - 38 10 3.3 10 8
39 - 44 12 3.3 12 8
TLB3030035
45 - 50 14 3.8 14 9
3030 108 to 90 2 5/8”
51 - 58 16 4.3 16 10
TLB3030075 59 - 65 18 4.4 18 11
66 - 75 20 4.9 20 12
35 - 38 10 3.3 10 8
39 - 44 12 3.3 12 8
TLB3525048
45 - 50 14 3.8 14 9
3525 127 to 113 3 1/2”
51 - 58 16 4.3 16 10
TLB3525090 59 - 65 18 4.4 18 11
66 - 75 20 4.9 20 12
76 - 86 22 5.4 22 14
86 - 90 25 5.4 25 14
35 - 38 10 3.3 10 8
TLB3535035
39 - 44 12 3.3 12 8
3535 127 to 113 3 1/2”
45 - 50 14 3.8 14 9
TLB3535090 51 - 58 16 4.3 16 10
59 - 65 18 4.4 18 11
66 - 75 20 4.9 20 12
76 - 86 22 5.4 22 14
86 - 90 25 5.4 25 14
40 - 44 12 3.3 12 8
TLB4040040
45 - 50 14 3.8 14 9
4040 146 to 170 3 5/8”
51 - 58 16 4.3 16 10
TLB4040100 59 - 65 18 4.4 18 11
66 - 75 20 4.9 20 12
76 - 86 22 5.4 22 14
86 - 96 25 5.4 25 14
96 - 100 28 6.4 28 16
TLB4545055
55 - 58 16 4.3 16 10
4545 162 to
59 - 65 18 4.4 18 11 192 3 3/4”
TLB4545110 66 - 75 20 4.9 20 12
76 - 86 22 5.4 22 14
86 - 96 25 5.4 25 14
TLB5050070 96 - 110 28 6.4 28 16
5050 177.5 to 70 - 75 20 4.9 20 12
TLB5050125 76 - 86 22 5.4 22 14 271 3 7/8”
86 - 96 25 5.4 25 14
96 - 110 28 6.4 28 16
111 - 125 32 7.4 32 18
Note:
• Key ways are British standard metric B.S. 4235: Part 1:1972 and conform to I.S.O recommendations. Where a key is to be
used it should be parallel and side fitting with top clearance. Depth of key way is measured at the center.
• Taper Bush with Imperial bores can also be supplied.
62
- PowerWare®
Pulley balancing
Static Balancing
Concept: When the Pulley is statically balanced, then the center of mass lies on the axis of rotation.
Cross-check: Rotate the Pulley to any angular position and leave it. If it is statically balanced, then the
Pulley will retain its position.
Procedure:
a) You are provided with 4 different masses (in the from of bars) and thus “the shaft + 4 masses”
constitutes your system.
b) As of now you assume that the center of mass of the bars is at equidistant from the axis of rotation.
m1
r1 m3r3
r2 m2 m4r4
shaft
r4
r3 m2r2
m4
m3 m1r1
c) Orient the masses on the shaft in such a way that center of mass = ? m1r1=0
d) For that randomly orient masses m1 and m2 (i.e.2) and then analytically solve for getting orientation
of 3 and 4 (i.e. 4).
e) Manually orient m3 and m4 at calculated angles ‘4’ and then see if there is an unbalance, there
will be most probably.) .
f) You then need to finely adjust the orientations of any two masses to make the system
statically stable.
Dynamic balancing:
Dynamic balancing is highly recommended in the applications running at high speeds.
OR
RPM=25.54 x 15,500 / (DF)½, where ‘D’ is Pulley diameter in mm and ‘F’ is the Pulley face width in mm.
Resultant RPM is the maximum recommended operating RPM for a sheave or a Pulley with a single
plane balance (static balancing).
Note: if a sheave or Pulley is to be operated at higher speed, two plane balancing is recommended.
63
- PowerWare®
Pulley alignment inspection
Misalignment can either be quantified mathematically, or be compared to some general rules of
thumb for quicker and easier results. While using a straight edge to project the plane of the outside
face of the sheave or sprocket #1 with respect to sheave or sprocket #2, angular misalignment can be
quantified as the difference in clearance between the straight edge and the outside surface of the
sheave or sprocket #2 across the diameter.
M1
M2
M2 - M1
Misalignment = Tan-1
D
The angle of parallel misalignment can be quantified as the difference in clearance between the
straight edge and the outer surfaces of the two sheaves or sprockets across the separation distance.
D
Misalignment = Tan-1
C
The total allowable misalignment recommended for V-Belts, in general, is 1/2-degree. While
individual V-Belts are known to be capable of handling greater amounts of misalignment before
becoming unstable, maintaining the misalignment to within 1/2-degree will maximize Belt life.
The total amount of misalignment recommended for synchronous, banded Belts and poly-V Belts is
1/4-degree. These drives are less tolerant of misalignment than conventional V-Belt drives, and must
be aligned more accurately.
64
- PowerWare®
Step 2:
Step 1: Match the holes of
First insert the bush pulleys with those
in the pulley. of the bush.
Step 3: Step 4:
Insert the set-screws Tighten them further
manually, tighten them using allen-key.
with fingers till possible. Tighten the screws
alternately.
To remove: Carefully remove all the set-screws and insert the screw in the ejecting hole as shown in
below picture.
Step 5:
Tighten the screw
in the ejecting hole
to release the bush.
Service equipment
PIX Pulley Gauges
PIX Pulley Gauges are especially designed for checking the profiles of the
grooves in a pulley. They can be used in checking the grooves of both the
conventional and dual section pulleys.
380
65
- PowerWare®
Types of Pulleys
Timing Pulleys
Grading Pulleys
66
®
- PowerWare
Couplings
- PowerWare®
PIX-Tyre Couplings
Tyre Couplings are highly elastic, lubrication free, that tolerate
large amounts of misalignment in all the planes as well as offers
simple installation and inspection without disrupting the drive.
PIX-Tyre coupling ensures high torque transmitting capacity in motor generators & in various industrial
machines. The true tyre material is made from neoprene/ natural/synthetic rubber compounds
reinforced with Rayon/ Nylon/ Polyester cord to give superior rating & long durability, bore size is well
matched to attain maximum speed (rpm) ensuring minimum to nil slippage of the flexible element out
from the coupling assembly, in case of any faulty installation.
The flexible tyre coupling is a "torsionally elastic" coupling, which minimizes misalignment and
maximizes power transmission for optimum machine run time.
Key features:
• Backlash-free
• Low maintenance
• Torsionally flexible
• Absorbs misalignment
• Dampens vibrations and torsional oscillations
• Easy tyre replacement
1. Highly resilient, flexible tire cushion shock loads, smoothing out the load between driving and driven
machines enables high levels of misalignment to be accommodated.
2. Radially split tyre facilitates easy installation and removal without disturbing the driving or driven
shafts.
4. Taper flanges are made from high grade cast iron and the versatile design enables easy positioning on
the shafts. The clamping system prevents relative movement between the flexible tyre and the flange.
5. Tension member is cross-pile, synthetic tension member, which enables torque to be transmitted in
either direction.
6. Elastomeric compound available in either natural rubber or fire-resistant and anti-static chloroprene,
which provides the shape and damping of the tyre.
7. Taper Bush provides a wide range of bore diameters, and enables easy assembly on the shafts.
68
- PowerWare®
PIX-Tyre Couplings
DRIVE DESIGN
Design power: Multiply the normal running power by the service factor. This gives the design power
which is used as a basis for selecting the Coupling.
Coupling size: Refer to power ratings ‘Table-2’ and from the appropriate speed read across until a power
greater than that required in step (b) is found. The size of Coupling required is given at the head of that
column.
Bore size: From ‘Table-4’, select the appropriate Coupling size with available bore dimension details.
Table-1
Service factors
Special Cases TYPE OF DRIVEN UNIT
For applications where substantial shock,
vibration & torque fluctuations occur & Electric motors, steam turbines +Internal combustion engines, steam
for reciprocating machines (i.e. internal engines, water turbines
combustion engines, piston pumps &
Hours per day duty Hours per day duty
compressors) refer to PIX with all machine
details for torsional analysis 10 and under Over 10 to 16 incl. Over 16 10 and under Over 10 to 16 incl. Over16
CLASS 2*
Clay working machinery, general machine
tools, paper mill beaters & winders, rotary
1.30 1.40 1.5 1.80 1.90 2.00
pumps screens, rubber extruders, Textile
machinery, marine propellers and fans over
7.5kw
CLASS 3*
Bucket elevators, cooling tower fans, piston
compressors and pumps, foundry machinery,
metal presses, paper mill calenders, hammer 1.80 1.90 2.0 2.30 2.40 2.50
mills, presses and pulp grinders, rubber
calenders, pulverizers and positive
displacement blowers.
CLASS 4*
Reciprocating conveyors, gyratory crushers,
2.30 2.40 2.5 2.80 2.90 3.0
mills (ball, pebble and rod), rubber machinery
(Banbury mixers and mills) and vibratory
screens
*It is recommended that keys (with top clearance, if in Taper bushes) are fitted on application where load function is
expected.
.+Couplings for use with internal combustion engines may require special consideration, such as a flywheel configuration. To
know more, please contact our technical support team.
69
Table - 2
Power ratings (kW)
Speed in rpm Coupling size
PTC-040 PTC-045 PTC-050 PTC-060 PTC-070 PTC-080 PTC-085 PTC-090 PTC-100 PTC-110 PTC-120 PTC-140 PTC-160 PTC-180 PTC-200 PTC-220 PTC-250
100 0.21 0.40 0.55 1.10 1.70 3.64 3.20 3.81 5.30 7.40 12.50 19.50 32.60 57.50 84.00 105.00 131.50
200 0.43 0.77 1.10 2.20 3.40 5.30 6.50 7.65 10.00 15.00 25.00 39.50 65.00 115.00 170.00 210.00 265.00
300 0.65 1.18 1.68 3.30 5.10 7.90 9.50 11.50 16.00 22.50 37.00 59.10 97.90 171.80 252.20 312.80 395.00
400 0.89 1.55 2.20 5.45 6.80 10.60 12.80 15.30 21.20 29.80 49.40 78.90 130.00 231.00 335.00 418.00 530.00
500 1.11 1.95 2.80 5.55 8.50 16.20 16.00 19.10 26.50 37.30 62.00 98.50 163.00 288.00 421.00 520.00 658.00
PIX-Tyre Couplings
600 1.32 2.33 3.30 6.65 10.10 16.00 19.00 23.00 31.00 45.00 74.00 117.00 195.00 345.00 505.00 625.00 732.00
700 1.55 2.74 3.90 7.70 11.90 18.50 22.50 26.70 37.00 52.25 86.50 137.00 227.00 402.00 585.00 730.00 922.00
720 1.56 2.75 4.00 8.00 12.20 19.10 23.00 27.50 38.10 53.70 89.00 142.00 235.00 415.00 605.00 752.00 950.00
800 1.75 3.10 4.45 8.90 13.50 21.20 25.50 30.50 42.30 60.00 99.00 157.00 260.00 460.00 670.00 835.00 1055.00
900 1.96 2.98 4.85 10.00 15.20 23.50 28.50 34.50 74.50 67.00 111.00 176.00 292.00 518.00 755.00 939.00 1195.00
960 2.10 3.75 5.30 10.50 16.20 15.50 30.00 36.50 50.50 71.50 118.00 188.00 312.00 550.00 805.00 1002.00 1267.00
1000 2.20 3.80 5.50 11.00 16.80 26.20 32.00 38.00 53.50 74.50 124.00 196.00 325.00 573.00 840.00 1044.00 1320.00
1200 2.65 4.65 6.65 13.20 20.30 31.50 38.50 45.50 63.50 89.50 148.00 235.00 390.00 686.00 1006.00 - -
1400 3.06 5.45 7.70 15.50 23.60 37.00 45.00 53.50 73.00 103.00 172.00 275.00 455.00 802.00 - - -
1440 3.15 5.60 8.00 15.80 24.30 38.00 45.00 55.00 76.00 106.00 177.00 285.00 470.00 825.00 - - -
1600 3.50 6.25 8.80 17.80 27.00 42.00 51.00 61.00 84.00 118.00 197.00 314.00 520.00 - - - -
1800 3.95 7.00 10.00 20.00 30.40 47.50 57.50 68.60 95.00 133.00 222.00 354.00 - - - - -
70
2000 4.36 7.60 11.00 22.00 34.00 52.00 63.00 76.00 106.00 148.00 246.00 - - - - - -
2200 4.82 8.60 12.10 24.50 37.30 58.30 70.50 84.00 115.00 165.00 - - - - - - -
2400 5.10 9.35 13.20 26.50 40.60 63.50 77.00 91.60 127.00 - - - - - - - -
2600 5.70 10.10 14.50 59.00 44.00 69.00 83.00 99.50 135.00 - - - - - - - -
2800 6.15 10.90 15.50 31.00 47.50 74.20 89.50 106.00 - - - - - - - - -
2880 6.30 11.20 16.00 32.00 49.00 76.00 92.00 110.00 - - - - - - - - -
3000 6.61 11.80 16.80 33.40 51.00 79.60 96.00 - - - - - - - - - -
3500 7.72 13.60 19.50 39.00 59.00 - - - - - - - - - - - -
3600 7.90 14.00 20.00 40.00 - - - - - - - - - - - - -
*All these power ratings are calculated at constant torque. For speeds below 100 rev / min and intermediate speeds, use nominal torque ratings
L L
L M M
M
I I I I I I #
I # I E G H E G H
E G H
J K J K J K
- PowerWare®
inch 3/7 1 1/4 2 7/8 - 1 1 3/7 1 1/9 2 2/3 - 6/7 1 1/3 1 1/7 4 5/7 3 5/7 1 2/3 1
mm 16 38 92 79 32 46 1210 32 78 79 25 39 38 133.5 100 43 28
PTC-050 M5 4.1 3.1 4
inch 5/8 1 1/2 3 5/8 3 1/9 1 1/4 1 4/5 1 1/4 3 3 1/9 1 1 1/2 1 1/2 5 1/4 4 1 2/3 1 1/9
mm 16 48 112 73 38 43 1610 42 86 103 25 43 38 165 125 43 36
PTC-060 M6 5 5.2 5
inch 5/8 1 8/9 4 2/5 2 7/8 1 1/2 1 2/3 1 2/3 3 2/5 4 1 1 2/3 1 1/2 6 1/2 5 1 2/3 1 3/7
mm 19.05 55 132 82 45 50.5 1610 42 92 76 25 50.5 38 197 144 10 42
PTC-070 M6 8 7.4 5
inch 3/4 2 1/6 5 1/5 3 2/9 1 7/9 2 1 2/3 3 5/8 3 1 2 1 1/2 7 3/4 5 2/3 2/5 1 2/3
mm 25.4 65 149 95 51 53 2012 50 111 95 32 53 47 211 167 10 47
PTC-080 M10 12 9.2 6
inch 1 2 5/9 5 6/7 3 3/4 2 2 2 4 3/8 3 3/4 1 1/4 2 1 6/7 8 1/3 6 4/7 2/5 1 6/7
mm 31.75 76 164 110 57 59.5 2517 60 140 110 45 59.5 50 235 188 13 50
PTC-090 M12 15 15.0 6
inch 1 1/4 3 6 1/2 4 1/3 2 1/4 2 1/3 2 1/3 5 1/2 4 1/3 1 7/9 2 1/3 2 9 1/4 7 2/5 1/2 2
mm 31.75 84 178 124 60 61.5 2517 60 148 124 45 61.5 50 254 216 13 58
PTC-100 M12 21 20.0 6
71
inch 1 1/4 3 1/3 7 4 7/8 2 1/3 2 3/7 2 1/3 5 5/6 4 7/8 1 7/9 2 3/7 2 10 8 1/2 1/2 2 2/7
mm 32 90 180 134 65 63.5 2517 60 150 134 45 63.5 50 279 233 14 50
PTC-110 M12 28 26.5 6
inch 1 1/4 3 1/2 7 5 2/7 2 5/9 2 1/2 2 1/3 6 5 2/7 1 7/9 2 1/2 2 11 9 1/6 5/9 2
mm 38.1 102 207 152 76 70 3020 75 157 152 51 70 68 314 264 14 55
PTC-120 M12 41 35.5 6
inch 1 1/2 4 8 1/7 6 3 2 3/4 3 6 1/6 6 2 2 3/4 2 2/3 12 1/3 10 2/5 5/9 2 1/6
mm 75 120 204 195 89 76 3535 90 204 197.5 89 76 89 359 313 14 26
PTC-140 M20 61 67.2 8
inch 3 4 5/7 8 7 2/3 3 1/2 3 3 1/2 8 7 7/9 3 1/2 3 3 1/2 14 1/7 12 1/3 5/9 1
mm 75 140 220 216 102 78 4040 100 220 216 102 78 110 402 345 19 16
PTC-160 M20 86 91.0 8
inch 3 5 1/2 8 2/3 8 1/2 4 3 4 8 2/3 8 1/2 4 3 4 1/3 15 5/6 13 4/7 3/4 5/8
mm 75 150 258 266 114 94 4545 110 258 266 114 94 126 470 398 19 30
PTC-180 M20 141 146.0 10
inch 3 6 10 1/6 10 1/2 4 1/2 3 5/7 4 1/3 10 1/6 10 1/2 4 1/2 3 5/7 5 18 1/2 15 2/3 3/4 1 1/6
mm 75 150 276 266 114 103 4545 110 278 266 114 103 126 508 429 19 48
PTC-200 M20 179 182.0 12
inch 3 6 10 6/7 10 1/2 4 1/2 4 4 1/3 11 10 1/2 4 1/2 4 5 20 16 8/9 3/4 1 8/9
mm 90 160 312 267 127 118 5050 125 312 267 127 118 140 562 474 20 56
PTC-220 M20 312 320.0 12
inch 3 1/2 6 2/7 12 2/7 10 1/2 5 4 2/3 5 12 2/7 10 1/2 5 4 2/3 5 1/2 22 1/8 18 2/3 4/5 2 1/5
mm 100 190 360 290 150 125 - - - - - - - 628 532 25 60
PTC-250 M20 500 - 12
inch 4 7 1/2 14 1/6 11 3/7 6 5 - - - - - - 24 5/7 21 1 2 1/3
M*=Distance between the flanges
x
K()= Amount to release tyre by withdrawing clamping screws
W(w)= Wrench clearance for loosening and tightening of bushes
- PowerWare®
- PowerWare®
PIX-Tyre Spacer Couplings
E
Comprising a PIX-Tyre coupling (size PTC
T 40-PTC 140) complete with a spacer flange
designed for use on applications where it is
C A an advantage to be able to move either
shaft axially without disturbing the driving
or driven machine; e.g. centrifugal pump
rotors. PIX-Tyre Spacer Couplings are
S
DBSE
primarily designed for the standard
distance between shaft end dimensions
100, 140 and 180 mm.
Table-4
PIX Spacer PIX
Spacer Size DBSE Tyre Bush Max. Tyre Max. A C E S T
size Coupling size bore Coupling bore
size Bush size
mm 80 32 25 104 118 134 77 25
PSM12 PTC40 PTC40 1008
inch 3 1/7 1 1/4 1 4 4 2/3 5 2/7 3 1
mm 100 32 25 104 118 140 97 25
PSM12 PTC40 PTC40 1008
inch 4 1 1/4 1 4 4 2/3 5 1/2 3 5/6 1
mm 100 42 25 104 127 170 94 32
PSM16 PTC40* PTC40* 1008
inch 4 1 2/3 1 4 5 6 2/3 3 5/7 1 1/4
mm 140 42 25 104 127 210 134 32
PSM16 PTC40* PTC40* 1008
inch 5 1/2 1 2/3 1 4 5 8 1/4 5 2/7 1 1/4
mm 100 42 32 133 1/2 127 173 94 32
PSM16 PTC50 PTC50 1210
inch 4 1 2/3 1 1/4 5 1/4 5 6 4/5 3 5/7 1 1/4
mm 140 42 32 133 1/2 127 213 134 32
PSM16 PTC50 PTC50 1210
inch 5 1/2 1 2/3 1 1/4 5 1/4 5 8 2/5 5 2/7 1 1/4
mm 100 42 42 165 127 177 94 32
PSM16 PTC60 PTC60 1610
inch 4 1 2/3 1 2/3 6 1/2 5 7 3 5/7 1 1/4
mm 140 42 42 165 127 214 134 32
PSM16 PTC60 PTC60 1610
inch 5 1/2 1 2/3 1 2/3 6 1/2 5 8 3/7 5 2/7 1 1/4
mm 100 60 42 197 178 180 94 42
PSM25 PTC70 PTC70 1610
inch 4 2 1/3 1 2/3 7 3/4 7 7 3 5/7 1 2/3
mm 140 60 42 197 178 220 134 42
PSM25 PTC70 PTC70 1610
inch 5 1/2 2 1/3 1 2/3 7 3/4 7 8 2/3 5 2/7 1 2/3
mm 180 60 42 197 178 260 174 42
PSM25 PTC70 PTC70 1610
inch 7 2 1/3 1 2/3 7 3/4 7 10 1/4 6 6/7 1 2/3
mm 100 60 50 211 178 193 94 48
PSM25 PTC80 PTC80 2012
inch 4 2 1/3 2 8 1/3 7 7 3/5 3 5/7 1 8/9
mm 140 60 50 211 178 233 134 48
PSM25 PTC80 PTC80 2012
inch 5 1/2 2 1/3 2 8 1/3 7 9 1/6 5 2/7 1 8/9
mm 180 60 50 211 178 273 174 48
PSM25 PTC80 PTC80 2012
inch 7 2 1/3 2 8 1/3 7 10 3/4 6 6/7 1 8/9
mm 140 60 60 235 178 235 134 48
PSM25 PTC90 PTC90 2517
inch 5 1/2 2 1/3 2 1/3 9 1/4 7 9 1/4 5 2/7 1 8/9
mm 180 60 60 235 178 275 174 48
PSM25 PTC90 PTC90 2517
inch 7 2 1/3 2 1/3 9 1/4 7 10 5/6 6 6/7 1 8/9
mm 140 75 60 254 216 269.5 134 60
PSM30 PTC100 PTC100 2517
inch 5 1/2 3 2 1/3 10 8 1/2 10 3/5 5 2/7 2 1/3
mm 180 75 60 254 216 309.5 174 60
PSM30 PTC100 PTC100 2517
inch 7 3 2 1/3 10 8 1/2 12 1/5 6 6/7 2 1/3
mm 140 75 60 279 216 369.5 134 60
PSM30 PTC110 PTC110 2517
inch 5 1/2 3 2 1/3 11 8 1/2 14 5/9 5 2/7 2 1/3
mm 180 75 60 279 216 309.5 174 60
PSM30 PTC110 PTC110 2517
inch 7 3 2 1/3 11 8 1/2 12 1/5 6 6/7 2 1/3
mm 140 90 75 314 248 297.5 134 75
PSM35 PTC120 PTC120 3020
inch 5 1/2 3 1/2 3 12 1/3 9 3/4 11 5/7 5 2/7 3
mm 180 90 75 314 248 327.5 174 75
PSM35 PTC120 PTC120 3020
inch 7 3 1/2 3 12 1/3 9 3/4 12 8/9 6 6/7 3
mm 140 90 90 359 248 296 134 80
PSM35 PTC140 PTC140 3535
inch 5 1/2 3 1/2 3 1/2 14 1/7 9 3/4 11 2/3 5 2/7 3 1/7
mm 180 90 90 359 248 336 174 80
PSM35 PTC140 PTC140 3535
inch 7 3 1/2 3 1/2 14 1/7 9 3/4 13 2/9 6 6/7 3 1/7
• PTC40* 'B' type coupling flange must be used to fit spacer shaft • DBSE :Distance between the shaft ends
72
- PowerWare®
PIX-Tyre Spacer Couplings
Step 1:
From the ‘Table -1’ , select appropriate service factor (SF) , the appropriate service factor in this case is
1.90
Step 2 :
To determine design power, multiply motor power with above selected service factor
PIX-Tyre Couplings
Installation
1. Thoroughly clean all the components, paying particular attention to the removal of the protective coating
inside the bore of the flanges.
2. Fit flanges to the shafts placing the external clamp rings on the shafts. (Where taper flanges are used, see
separate fitting instructions supplied with the taper Bushes). Locate flanges so that dimension ‘M2’ is
obtained (see paragraph 3). Flanges with internal clamping rings should then have the clamping rings
fitted, engaging only two or three of the threads of the screws at this time.
3. Bring the shafts close to each other until dimension ‘M2’ is obtained (Table-5). If a shaft end float is to
occur, locate the shafts at mid-position of end float when checking dimension ‘M2’. Note that shaft ends
may project beyond the faces of the flanges, if required. In this event, allow sufficient space between shaft
ends for end float and misalignment. Flanges should be fitted, flushed with the end of the shaft when
used with mill-motor flanges.
Sealing Dia.
External M2
Internal for Tyre
M2 Seating Dia. Clamping
Clamping for Tyre Ring
Ring
Flange
Flange
73
- PowerWare®
PIX-Tyre Couplings
Installation
Table-5
Coupling size Coupling size
Unit
PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC PTC
40* 45* 50* 60* 70 80 90 100 110 120 140 160 180 200 220 250
M2 (mm) mm 23 23 28 36 42 47 50 58 50 55 26 16 30 48 56 60
inch 1 1 1 1 3/7 1 2/3 1 6/7 2 2 2/7 2 2 1/6 1 5/8 1 1/6 1 8/9 2 1/5 2 1/3
Clamping screw
torque (Nm) 15 15 15 15 24 24 32 32 32 35 35 35 35 35 38 38
Unless otherwise specified flexible tyres will be supplied in a natural rubber compound, which are suitable for
operation in temperatures range -15°C to +70°C.
4. Check parallel alignment by laying a straight edge across the flanges at several positions around the
circumference. Check angular alignment by measuring the gap between the flanges at several positions
around the circumference. It is desirable to align the coupling as accurately as possible, particularly on
high speed applications.
5. Open out tyre and fit over coupling flanges ensuring that the tyre beads seat properly on the flanges
and/or clamping rings. To ensure proper seating, it may be necessary to strike the outside diameter of the
tyre with a small mallet. When seated, there should be a gap between the ends of the tyre as shown in
‘Table-6’.
Table-6
Coupling size Unit F40 to F60 F70 to F120 F140 F160 to F180 F200 to F250
mm 2 3 5 6.5 8.0
Tyre gap
inch 3 3/8 1/8 1/5 1/4 1/3
6. Tighten clamping ring screws alternately and evenly (half-turn at a time) working around each flange.
74
- PowerWare®
PIX-Gear Couplings
PIX Gear type couplings are made for high mechanical flexibility, and torsionally rigid design. PIX Gear
coupling consists of two hubs, which have external teeth crowned over them, and two outer sleeves which
have internal spur teeth.
Carbon steel is used to manufacture hubs and sleeves, and are provided with proper hardness and
dimensions with very close tolerances, which result in proper tooth meshing and inter changeability.
Key Features :
• Comprises of two hubs having external teeth and two sleeves having internal spur teeth, which couple
together to provide highly efficient coupling.
• Hubs and sleeves are manufactured with carbon steel, and very fine surface finish is maintained so as to
provide flawless dimensional accuracy and efficient meshing of tooth.
• These are designed to resist corrosion, so as to increase the scope of application in various industries.
DRIVE DESIGN
Service factor: Determine the required service factor from the ‘Table-1’.
Design power: Multiply the normal running power by the service factor. This gives the design power
which is used as a basis for selecting the coupling.
Coupling size: Refer to power rating from ‘Table-2’ and from the appropriate speed read across until a
power greater than OR equal to that required design power is found. The size of coupling required is
given in the header of that column.
Bore size: From ‘Table-3’, select the appropriate coupling size with available bore dimension details.
75
- PowerWare®
PIX-Gear Couplings
Table-1
A list of service factors for the more common
type of machines is given below Prime Mover
LIGHT:
Uniform of Steady load never exceeding horse
1.0 1.5 2.0
rating, infrequent starting; Agitators, blowers,
can filling machines, conveyors, fans,
generators, pumps, steering gear, stokers
MODERATE:
Heavy inertia, moderate shock, frequent
starting; peak loads do not exceed 125 per
cent average horsepower. 1.5 2.0 2.5
Hub
H H H H
J1 J K E
J KE I
I
‘O’ ring
Fitted
Bolts GG
GG Rigid Half Flex half
F
76
- PowerWare®
PIX-Gear Couplings
PGC-4 mm 110 40 100 250 215 20 105 5 138 160 178 125
inch 4 1/3 1 4/7 4 9 5/6 8 1/2 4/5 4 1/7 1/5 5 3/7 6 2/7 7 5
PGC-5 mm 130 46 120 290 240 25 115 10 166 185 204 140
inch 5 1/8 1 4/5 4 5/7 11 3/7 9 4/9 1 4 1/2 2/5 6 1/2 7 2/7 8 5 1/2
PGC-6 mm 150 50 125 320 260 25 125 10 176 215 230 155
inch 6 2 5 12 3/5 10 1/4 1 5 2/5 7 8 1/2 9 6 1/9
PGC-07 mm 170 60 145 350 290 25 140 10 208 240 260 175
inch 6 2/3 2 1/3 5 5/7 13 7/9 11 3/7 1 5 1/2 2/5 8 1/5 9 4/9 10 1/4 6 8/9
PGC-08 mm 200 70 165 380 330 25 160 10 230 285 290 200
inch 7 7/8 2 3/4 6 1/2 15 13 1 6 2/7 2/5 9 11 2/9 11 3/7 7 7/8
PGC-09 mm 220 80 200 430 340 25 165 10 270 315 332 210
inch 8 2/3 3 1/7 7 7/8 17 13 2/5 1 6 1/2 2/5 10 5/8 12 2/5 13 8 1/4
PGC-10 mm 260 100 230 490 370 25 180 10 315 370 390 230
inch 10 1/4 4 9 19 2/7 14 4/7 1 7 2/5 12 2/5 14 4/7 15 1/3 9
PGC-11 mm 280 110 260 545 410 30 200 10 350 380 445 270
inch 11 4 1/3 10 1/4 21 1/2 16 1/7 1 1/6 7 7/8 2/5 13 7/9 15 17 1/2 10 5/8
PGC-12 mm 310 150 300 590 490 30 240 10 404 420 490 300
inch 12 1/5 6 11 4/5 23 2/9 19 2/7 1 1/6 9 4/9 2/5 16 16 1/2 19 2/7 11 4/5
* Apart from above, higher range sizes would be available on request.
Application
Dredgers, cranes, paper machinery, metal rolling mills, conveyors & elevators, cement plants, fans &
blowers, compressors, rubber & plastic industries
77
- PowerWare®
PIX-Gear Couplings
Installation
Install the flange sleeves with the seal rings before the hubs. Clean all the metal
parts using non-flammable solvent and check the hubs, shafts and keyways for
burrs and remove, if necessary.
Apply light coat of grease to the seals and place it back on the shafts prior to
mounting the hubs. Both the shafts can be lubricated with light oil or anti-seize
compound. Mount the hubs on their respective shafts so that each hub face is
flushed with the end of the shaft.
Alignment
Angular Alignment: Insert a ‘Feeler gauge’ equal to the thickness of the gap specified in ‘ Table-4’. Insert the
gauge as shown in image & measure the clearance between the gauge and hub face. The difference in the
minimum and the maximum measurements must not exceed the angular limits specified in ‘Table-4’.
J
J J
K
M
78
- PowerWare®
PIX-Gear Couplings
Parallel Alignment: Align the two hubs so that a straight edge rests squarely on both the hubs at various
positions. The clearance must not exceed the parallel offset installation limits specified in ’Table-4’. Tighten
all foundation bolts and repeat steps 2 and 3. Realign the Coupling, if necessary.
Fill with grease & assemble the sleeves: Fill the gear of the hubs with grease & Insert a gasket between the
sleeves. Position the sleeves with the lubrication holes approximately 90° apart. Then push the sleeves into it
using the fasteners, bolt the sleeves together. Once the Coupling is assembled, remove the lubrication plugs
from the sleeves. Insert grease fitting in one of the holes and pump grease into the sleeve until it is forced out
of the opposite lubrication hole. Replace the lubrication plugs, the installation is complete.
79
- PowerWare®
PIX Star coupling is a three-pieced design which consists of two hubs and an elastomeric element called
“the spider”. Star coupling hubs are machined with high precision, they fit with the spider, assuring zero-
backlash operation. The curved star profile is aimed to concentrate the forces to the centre of the
spider’s limbs, thus providing high effectiveness to the elastomer material. Flexible members are
provided with proper torsional stiffness to dampen the impulse load, while countering misalignment.
PIX-Spacer Star Couplings can be used to connect two shafts having larger distances between them. A
star coupling is a general purpose power transmission coupling . It is designed to transmit torque (by
connecting two shafts) while damping system vibrations and accommodating misalignment, which
protects other components from damage.
Star couplings consist of three parts: two metallic hubs and an elastomer insert called as an element, but
commonly referred to as a "spider". The three parts press-fit together with a star from each hub fitted
alternately with the lobes of the spider. The torque here is transmitted through the elastomer lobes in
compression. The elastomer of the spider is made of nitrile rubber , which offers good flexibility.
Considerations for elastomer selection include ability to dampen the vibrations, handle misalignment,
operational temperature range, speed of the equipment, and chemical conditions.
Star couplings are considered "fail-safe" because, should the elastomer fail or wear away, the Star
coupling hub teeth will mate, much like teeth on two gears, and continue to transmit torque. This may or
may not be desirable to the user depending on the application. Star couplings elastomers are wearing
elements that do need to be inspected and replaced.
Star coupling elastomers often have signature wear patterns, and failures can often be root caused
based on the condition of the elastomer and hubs.
Common failure causes include misalignment, over-torque, chemical exposure, temperature exposure,
torsional vibrations, and hub failure.
Key Features:
Easy installation: No need of special tools for installation.
Accommodates misalignment: compensates for small axial, parallel & angular misalignments.
Shock absorbent: Flexible member is able to absorb shock loads, and dampen minor vibrations.
Spacer couplings available: Can cater shafts at large distances with Spacer Star couplings.
Physically robust: Can resist moisture, oils, greases. The flexible rubber element can withstand high
temperatures.
80
- PowerWare®
Standard Star Couplings I
F H
J J
Table-1 E
Product range
Bore Dimensions Power rating (Kw)
Size Unit at 100 RPM
Min Max E F H I J
mm 15 28 60 54 49 2 25
PSC-095 0.2
inch 3/5 1 1/9 2 1/3 2 1/8 2 3/38 1
mm 20 38 88 65 57 2 35
PSC-0100 0.5
inch 4/5 1 1/2 3 1/2 2 5/9 2 1/4 3/38 1 3/8
mm 20 32 108 85 76 3 43
PSC-0110 0.91
inch 4/5 1 1/4 4 1/4 3 1/3 3 1/8 1 2/3
mm 30 48 115 96 80 3 45
PSC-0150 1.51
inch 1 1/6 1 8/9 4 1/2 3 7/9 3 1/7 1/8 1 7/9
mm 36 55 133 115 102 3 54
PSC-0190 2.02
inch 1 3/7 2 1/6 5 1/4 4 1/2 4 1/8 2 1/8
mm 40 60 153 127 108 3 64
PSC-0225 2.74
inch 1 4/7 2 1/3 6 5 4 1/4 1/8 2 1/2
F H
J E
Table-2
Product range
Bore Dimensions Power rating (Kw)
Size Unit
at 100 RPM
Min Max E F H I J
mm 25 65 178 143 115 2 70
PSC-0226-P 3.44
inch 1 2 5/9 7 5 5/8 4 1/2 3/38 2 3/4
mm 25 75 200 163 127 2 80
PSC-0276-P 5.61
inch 1 3 7 7/8 6 3/7 5 3/38 3 1/7
mm 30 75 200 200 140 3 80
PSC-0280-P 8.2
inch 1 1/6 3 7 7/8 7 7/8 5 1/2 1/8 3 1/7
mm 40 90 238 245 160 3 95
PSC-0295-P 13.35
inch 1 4/7 3 1/2 9 3/8 9 2/3 6 2/7 1/8 3 3/4
81
- PowerWare®
External Spider Star Couplings J
F H
Table-3
Product range E
X
Table-4 G E G
Product range
Bore Dimensions Power rating (Kw)
Size Unit
at 100 RPM
Min Max E (DSBE) F G X
mm 15 28 54 25 6
PSC-095-S 90/100 0.20
inch 3/5 1 1/9 2 1/8 1 1/4
mm 20 38 65 30 6
PSC-0100-S 90/100/140 0.50
inch 4/5 1 1/2 2 5/9 1 1/6 1/4
mm 20 42 85 35 8
PSC-0110-S 90/100/140 0.91
inch 4/5 1 2/3 3 1/3 1 3/8 1/3
mm 30 48 96 45 10
PSC-0150-S 90/100/140 1.51
inch 1 1/6 1 8/9 3 7/9 1 7/9 2/5
mm 36 55 115 51 10
PSC-0190-S 90/100/140 2.02
inch 1 3/7 2 1/6 4 1/2 2 2/5
mm 40 60 127 57 12
PSC-0225-S 90/100/140 2.74
inch 1 4/7 2 1/3 5 2 1/4 1/2
*DSBE- Distance between shaft ends
Application
General machine tools, packaging machinery, conveyors, elevators, pumps, ball mill beaters and
colanders, blowers
82
- PowerWare®
PIX-Star / Jaw Couplings
Table-5
Service factor
PRIME MOVER
TYPE OF DRIVEN MACHINE Gasoline or
Electric Motors, Gasoline or diesel engine,
diesel engine,
Steam Turbines 6 or more Cyl.
6 or less than Cyl.
LIGHT
Blowers, uniform or steady load never
1.0 1.5 2.0
exceeding horsepower fans, generators,
centrifugal pumps, stokers, rating, pumps,
infrequent starting, agitators, blowers,
conveyors, evaporators
MODERATE
Beaters, rotary pumps and compressors,
cranes, elevators, mine and propeller fans,
generators, pulp grinders, hoists, kilns,
1.5 2.0 2.5
machine tools, mixers, gear pumps,
woodworking machines, heavy inertia,
moderate shock, frequent starting; peak
loads do not exceed 125 per cent average
horsepower. Uneven load.
HEAVY
Uneven load. Reciprocating pumps and
compressors, crushers, freight and
passenger elevators, mills (Hammer, ball,
rolling, turf, flour), vibrating screens, 2.0 2.5 3.0
winches, wire drawing machines,
punches, shears heavy shock conditions
or frequent reversing. Peak loads do not
exceed 150 per cent. average horsepower.
DRIVE DESIGN
Service factor: Determine the required service factor from ‘Table-5’.
Design power: Multiply the normal running power by the ‘service factor’. This gives the design power, which
is used as a basis for selecting the coupling.
Coupling size: Refer to power ratings from ‘Table-‘6 and from the appropriate speed read across until a
power greater than or equal to that required design power is found. The size of the coupling can be known
from the header of the table.
Bore size: From the ‘Tables 1-4’, select the appropriate Coupling size with available bore dimension details.
Table-6
Power rating
Standard Jaw Size PJC-075 PJC-095 PJC-100 PJC-110 PJC-150 PJC-190 PJC-225
coupling Power/100rpm(kw) 0.12 0.20 0.50 0.91 1.51 2.02 2.74
Cushion Jaw Size PJC-226-P PJC-276-P PJC-280-P PJC-295-P - - -
coupling Power/100rpm(kw) 3.44 5.61 8.20 13.35 - - -
External Spider Size PJC-095 E PJC-100 E PJC-110 E PJC-150 E PJC-190 E PJC-225 E -
Jaw coupling Power/100rpm(kw) 0.22 0.49 0.90 1.48 2.02 2.80 -
Standard Spacer Size PJC-095-S PJC-100-S PJC-110-S PJC-150-S PJC-190-S PJC-0225-S -
Jaw coupling Power/100rpm(kw) 0.20 0.50 0.91 1.51 2.02 2.74 -
83
- PowerWare®
Step 1 :
From service factor (SF), ‘ Table-5’, SF selected = 1.0
Step 2 :
To calculate design power (Pd)
Design power (Pd) = Motor power x SF
=5 x 1.0
= 5kW
Step 3 :
To determine coupling size
When looking for 500 RPM/min in ‘Table-1’ above (power rating), the first power figure to exceed the
required 5kW and ‘Step 2 is 7.55 kW (1.51 x 5).
Installation
The performance of the coupling depends largely upon how it is installed, aligned and maintained.
Installation procedure:
Mounting:
• Remove the dust, dirt, and oil accumulated on the target shaft and from the inner part of the coupling.
• To achieve maximum performance, perform mounting within the range of the maximum permissible
misalignment shown in ‘Table-7’. The misalignments in the table are the maximum values when they occur
independently. Therefore, the permissible values in the case of combined errors are half or less.
• Check the centering at two points about 90 degrees away by applying a straight edge to the circumference
of the main body. The life of the element is significantly affected by the centering accuracy. For centering of
the left and right mounting shafts, centering location alignment is recommended.
84
- PowerWare®
Table-7
Parallel Angular Axial
Type offset misalignment displacement
å (mm) È (?) ä (mm)
PSC-095 0.10 1 0 to +0.5
PSC-100 0.10 1 0 to +0.8
PSC-110 0.10 1 0 to +1.0
PSC-150 0.15 1 0 to +1.3
PSC-190 0.15 1 0 to +1.5
PSC-225 0.15 1 0 to +1.8
PSC-226 0.15 1 0 to +2.0
PSC-276 0.25 1 -0.5 to + 2.0
PSC-280 0.25 1 -0.5 to + 2.0
PSC-295 0.25 1 -0.5 to + 2.0
PSC-2955 0.25 1 -0.5 to + 2.0
• It is moisture, grease and oil-resistant, including non- aromatic & non ketone solvents. However, excessive
oil should be avoided, it may cause deterioration.
85
- PowerWare®
PIX-HRC Couplings
HRC Couplings offer a range of hub and element selection to meet the demand for a low cost, general
purpose spacer type flexible coupling. They allow for incidental misalignment, absorb shock loads and
dampen out small amplitude vibrations. They are offered in both pilot bore, finished bore, and taper bushed
with both face and hub mount.
These semi-elastomeric couplings are designed for general purpose applications and permit quick and easy
assembly by means of taper bush. Outside diameters are fully machined to allow alignment by simple
straight edge methods. HRC Couplings require no lubrication and are virtually maintenance free, making
them suitable for most environments.
DRIVE DESIGN
Service factor: Determine the required service factor from ‘Table-1’.
Design power: Multiply the normal running power by the service factor. This gives the design power
which is used as a basis for selecting the coupling.
Coupling size: Refer to power ratings from ‘Table-2’ and from the appropriate speed read across until a
power greater than OR equal to that required design power is found. The size of the coupling required can
be known from the header of the table.
Bore size: From ‘Table-4’, select the appropriate coupling size with available bore dimension details.
Table-1
Service factors
Special Cases TYPE OF DRIVEN UNIT
For applications where substantial shock,
vibration & torque fluctuations occur & for +Internal combustion engines, steam
Electric motors, steam turbines
reciprocating machines (i.e. internal engines, water turbines
combustion engines, piston pumps &
Hours per day duty Hours per day duty
compressors) and compressors) machines
vibration(e.g.and refer torque internal to 8 and under over 8 to 16 incl. Over 16 8 and under over 8 to 16 incl. over16
86
- PowerWare®
PIX-HRC Couplings
Table-2, Power ratings (kW)
COUPLING SIZE
Speed
Rev/Min
PHRC 070 PHRC 090 PHRC 110 PHRC 130 PHRC 150 PHRC 180 PHRC 230 PHRC 280
Table-3
Physical characteristics
COUPLING SIZE
Characteristics Unit
PHRC 070 PHRC 090 PHRC 110 PHRC 130 PHRC 150 PHRC 180 PHRC 230 PHRC 280
Maximum speed* rev/min 8300 6740 5110 4400 3800 3180 2540 2080
Nominal torque (Nm) 31.5 80 160 315 600 950 2000 3150
Maximum parallel mm 0.3 0.3 0.3 0.4 0.4 0.4 0.5 0.5
misalignment inch 1/85 1/85 1/85 1/63 1/63 1/63 1/51 1/51
Maximum axial mm 0.2 0.5 0.6 0.8 0.9 1.1 1.3 1.7
misalignment inch 1/127 1/51 2/85 3/95 1/28 1/23 2/39 1/15
*Allowable peripheral speed for hub material has been used for calculating maximum coupling speeds.
G
Schematic drawing G
E F
E F
H
H
‘F’ Flange ‘H’ Flange
J K J
G G Length in assembled condition
Length in assembled condition
I I
E F E F
M H M
H
L L
HRC Assembly - F&H Type (Taper) HRC Assembly - ‘B’ Type
87
Table-4
Product range:
Type B Type F & H Power
Size Unit E F I M rating (Kw)
Min Max TLB Min Max at 100 RPM
PIX-HRC Couplings
G H J L G H J L K*
Bore Bore Size Bore Bore
mm 10 32 20 24 26 66 9 25 20 24 26 66 29 69 60 31 18
PHRC-070 1008 0.35
inch 2/5 1 1/4 4/5 1 1 2 3/5 1/3 1 4/5 1 1 2 3/5 1 1/7 2 5/7 2 1/3 1 2/9 5/7
mm 10 35 26 30 30.5 82.5 9 28 19.5 24 31.5 70.5 29 85 70 32 22.5
PHRC-090 1108 0.85
inch 2/5 1 3/8 1 1 1/6 1 1/5 3 1/4 1/3 1 1/9 3/4 1 1 1/4 2 7/9 1 1/7 3 1/3 2 3/4 1 1/4 8/9
mm 10 55 37 45 45 119 11 32 18.5 27 46 83 38 112 100 45 29
PHRC-110 1210 1.70
inch 2/5 2 1/6 1 1/2 1 7/9 1 7/9 4 2/3 3/7 1 1/4 3/4 1 1 4/5 3 1/4 1 1/2 4 2/5 4 1 7/9 1 1/7
mm 14 60 47 56 54 148 14 42 18 27 54 90 39 130 105 50 36
PHRC-130 1610 3.35
inch 5/9 2 1/3 1 6/7 2 1/5 2 1/8 5 5/6 5/9 1 2/3 5/7 1 2 1/8 3 1/2 1 1/2 5 1/8 4 1/7 2 1 3/7
mm 19 70 50 60 60 160 14 50 23.5 34 61 108 44 150 115 62 40
PHRC-150 2012 6.35
88
inch 3/4 2 3/4 2 2 1/3 2 1/3 6 2/7 5/9 2 1 1 1/3 2 2/5 4 1/4 1 3/4 6 4 1/2 2 4/9 1 4/7
mm 35 80 58 70 73 189 16 60 34.5 47 74 163 48 180 125 77 49
PHRC-180 2517 10.0
inch 1 3/8 3 1/7 2 2/7 2 3/4 2 7/8 7 4/9 5/8 2 1/3 1 1/3 1 6/7 3 6 3/7 1 8/9 7 5 3 2
mm 38 100 77 90 85.5 239.5 25 75 39.5 53 86.5 165.5 55 225 155 99 59.5
PHRC-230 3020 21.0
inch 1 1/2 4 3 3 1/2 3 3/8 9 3/7 1 3 1 5/9 2 3 2/5 6 1/2 2 1/6 8 6/7 6 1/9 3 8/9 2 1/3
mm 48 115 90 105 104.5 284.5 35 90 51 67 106.5 208.5 67 275 206 119 74.5
PHRC-280 3525 33.0
inch 1 8/9 4 1/2 3 1/2 4 1/7 4 1/9 11 1/5 1 3/8 3 1/2 2 2 2/3 4 1/5 8 1/5 2 2/3 10 5/6 8 1/9 4 2/3 3
K*- Wrench clearance to allow for tightening and loosening the bush on the shaft.
Application
Agitators, brewing machinery, centrifugal blower, compressors, generators, conveyor position type pumps, wood working
machinery, crane hoist, crushers, reciprocating conveyors etc.
- PowerWare®
- PowerWare®
PIX-HRC Couplings
Step1:
Determine the required service factor from ‘Table-1’
Service factor selected = 1.80
Step 2:
Determine the design power, multiply motor power with service factor
Design power = P x SF
=20 x 1.8
= 36 kW
Step3:
To determine the coupling size, search for 720RPM in power rating ‘Table-2’ and choose the first
power figure, which exceeds the required 36kW from ‘Table-2’, coupling size PHRC-150 can be used.
Installation
HRC Coupling allows for incidental misalignment, it absorbs shock loads, and is able to dampen out small
amplitude vibrations, making the HRC Coupling specially suited to hydraulic or combustion engine
applications.
The various different hub arrangements, in either ‘F’ (Face), ‘H’ (Hub), or ‘B’ (finished Bore) allows the Taper
Bush to enter the hub from two different directions. Firstly, the bush may enter the hub from inside the
coupling (F flange), which allows the coupling hub to be mounted against the bearing on a shaft, reducing
overhung loads. Secondly, it is able to enter the hub from outside the coupling (H flange), which assists with
ease of installation. Please refer below figures.
F
C C C
OD OD OD
D D D
L
‘B’ Flange ‘H’ Flange ‘F’ Flange
Assembled length
89
- PowerWare®
PIX-HRC Couplings
Installation
HRC Coupling is a semi-elastomeric coupling and is designed for general purpose applications. It permits
quick and easy assembly by means of a taper bush.
All outside diameters are fully machined, which allows for a high degree of accuracy via simple alignment
methods, such as using a straight edge or the 6 inch rule method. HRC Couplings are also a fail-safe design
due to their interacting jaw design & often referred to as a capacity balanced coupling’ because, if the shaft
fits, it will do the job.
• Before installation, check all components for suitability, particularly where, components previously in
service, are being reused. Check taper bushes and the HRC coupling hubs are free of contaminants,
lubricants, nicks, burns, and fatigue damage. Any type of contaminant or damage can affect the seating of
the taper bush, both on the shaft and in the female bore of the coupling hub (Applicable for Taper Bush
Coupling Installation).
• When placing the taper bush into the HRC coupling hub, half holes should be matched to make complete
holes. The taper bush should be oriented in order that each complete hole has thread on one side only
(Applicable for Taper Bush Coupling Installation).
• Before inserting the screws, ensure all threads are lubricated with oil. The screws should be started, but not
tightened, in the threads in the HRC coupling hub (Applicable for Taper Bush Coupling Installation).
• Slide one of the HRC coupling hubs and taper bush assemblies into position.
• Place the HRC coupling (rubber) element into the other hub and taper bush assembly.
90
- PowerWare®
PIX-HRC Couplings
• To ensure correct mating of the two hubs, ensure that coupling-assembled, total length is correct.
• Locate the coupling halves and element assembly approximately in the desired position. HRC couplings
are required to be mounted with an allowance for a small amount of float. This internal float allows for any
linear expansion and maintains the coupling’s misalignment capability.
• To ensure the tapers are seated correctly, it is recommended to tap the front face of the taper bush with a
nylon hammer or suitable soft drift to ensure no damage occurs to the taper bush. A torque wrench must
then be used to achieve the correct tension on the screws as defined in the ‘Table-5’. This procedure should
be carried out a number of times to ensure the tapers are correctly seated. After setting the screws to the
correct torque, they may require tightening again after tapping with the nylon hammer (Applicable for
Taper Bush Coupling Installation).
Table-5
Bush size 1008 1108 1210 1610 1615 2012 2517 3020 3030 3525 3535 4030 4040 4535 4545 5040 5050
Screw tightening
5.6 5.6 20 20 20 30 50 90 90 115 115 170 170 190 190 270 270
torque (Nm)
Qty 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3
Size
Screw 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3
(BSW)
Details
Max
Socket 3 3 5 5 5 6 8 8 8 10 10 12 12 14 14 14 14
size (mm)
Large end Dia.(mm) 35.0 38.0 47.5 57.0 57.0 70.0 85.5 108.0 108.0 127.0 127.0 146.0 146.0 162.0 162.0 177.5 177.5
Approx. mass (Kg) 0.1 0.1 0.2 0.3 0.3 0.7 1.5 2.7 3.6 3.8 5.0 5.6 7.7 7.5 10.0 11.1 14.0
• HRC couplings have a maximum misalignment capability of 1° degree. Correct attention to accurate
alignment of the coupling halves is, therefore, essential. Many methods of aligning shaft couplings are
available, all with varying degrees of resultant accuracy and skills required. Laser alignment is the most
effective and efficient in achieving accurate alignment (Applicable for Taper Bush Coupling Installation).
• After a period of normal running, it is often prudent to recheck the torque settings on the taper lock
bushing screws and re-tighten as necessary (Applicable for Taper Bush Coupling Installation).
• It is recommended that unfilled holes in the taper bush are filled with grease or silicon sealant to prevent
the entrance of contaminants and facilitate future removal requirements (Applicable for Taper Lock Bush
Coupling Installation).
• After the mounting, affix a safety cover. Touching this product during operation, may cause injury
(Applicable for Taper Bush Coupling Installation).
91
- PowerWare®
PBC is made for least downtime; it doesn’t need to be adjusted after fitting nor lubrication is required. It's
robust construction makes the flexible bushes unaffected by oil & grease, dust proof and unaffected
from atmospheric conditions.
.
Key Features:
Simple construction: Simple and compact construction, can be easily dissembled and assembled.
Suitable stiffness for smooth operation: Bushes are specially provided with proper stiffness, which
prevents the coupling from shocks and torsional vibration and counters, misalignment.
Easy servicing: Simple construction makes inspection and replacement of pin and bush very easy. It can
be dismantled without decoupling the shafts.
Silent and vibration free operation: Flexible member absorbs noise and vibration, thereby making the
operation smoother.
Absolutely no lubrication required: Bush couplings work without being lubricated, thus reduce the
downtime and operational costs.
Design power: Multiply the normal running power by the service factor. This gives the design power which is
used as a basis for selecting the coupling.
Coupling size: Refer the power rating ‘Table-3’, and from the appropriate speed read across until a power
greater than OR equal to that required design power is found. The size of coupling required is known from
the head of that column.
Bore size: From’ Table-3’, select the appropriate coupling size with available bore dimension details.
92
- PowerWare®
Schematic drawing
F
G H G
SHAFT
I
E
93
- PowerWare®
mm 12.7 28 95 79 38 3 40 58
PBC-1 3 78 6000 0.83
inch 1/2 1 1/9 3 3/4 3 1/9 1 1/2 1/8 1 4/7 2 2/7
mm 12.7 30 114 99 48 3 42 70
PBC-2 4 310 5100 3.24
inch 1/2 1 1/6 4 1/2 3 8/9 1 8/9 1/8 1 2/3 2 3/4
mm 16 42 130 105 51 3 60 70
PBC-2A 6 517 4400 5.50
inch 5/8 1 2/3 5 1/8 4 1/7 2 1/8 2 1/3 2 3/4
mm 16 48 160 107 50 5 68 114
PBC-3 4 620 3600 6.50
inch 5/8 1 8/9 6 2/7 4 1/5 2 1/5 2 2/3 4 1/2
mm 20 65 191 125 60 5 90 114
PBC-4 4 830 3000 8.60
inch 4/5 2 5/9 7 1/2 5 2 1/3 1/5 3 1/2 4 1/2
mm 20 65 191 125 60 5 90 114
PBC-4A 6 1240 3000 12.90
inch 4/5 2 5/9 7 1/2 5 2 1/3 1/5 3 1/2 4 1/2
mm 25 75 225 156 76 5 105 114
PBC-5 6 1660 2580 17.30
inch 1 3 8 6/7 6 1/7 3 1/5 4 1/7 4 1/2
mm 45 95 254 183 89 5 135 114
PBC-6 8 2360 2880 24.50
inch 1 7/9 3 3/4 10 7 1/5 3 1/2 1/5 5 1/3 4 1/2
mm 45 95 254 183 89 5 135 114
PBC-6A 10 2930 2880 30.50
inch 1 7/9 3 3/4 10 7 1/5 3 1/2 1/5 5 1/3 4 1/2
mm 45 95 254 183 89 5 135 114
PBC-6B 12 3530 2880 37.00
inch 1 7/9 3 3/4 10 7 1/5 3 1/2 1/5 5 1/3 4 1/2
mm 60 115 290 235 115 5 170 114
PBC-7 12 4152 1940 43.50
inch 2 1/3 4 1/2 11 3/7 9 1/4 4 1/2 1/5 6 2/3 4 1/2
mm 60 120 300 235 115 5 180 130
PBC-7A 14 5196 1920 54.50
inch 2 1/3 4 5/7 11 4/5 9 1/4 4 1/2 1/5 7 5 1/8
mm 65 130 310 255 125 5 195 130
PBC-8 16 5817 1840 60.80
inch 2 5/9 5 1/8 12 1/5 10 5 1/5 7 2/3 5 1/8
mm 65 135 340 265 130 5 210 130
PBC-8A 18 7270 1640 76.00
inch 2 5/9 5 1/3 13 2/5 10 3/7 5 1/8 1/5 8 1/4 5 1/8
mm 70 140 360 276 135 5 210 200
PBC-8B 12 8730 1580 91.50
inch 2 3/4 5 1/2 14 1/6 10 6/7 5 1/3 1/5 8 1/4 7 7/8
mm 80 150 390 316 165 6 225 200
PBC-9 13 9930 1460 104.00
inch 3 1/7 6 15 1/3 12 4/9 6 1/2 1/4 8 6/7 7 7/8
mm 90 160 410 336 165 6 240 200
PBC-9A 15 13275 1420 138.50
inch 3 1/2 6 2/7 16 1/7 13 2/9 6 1/2 1/4 9 4/9 7 7/8
mm 100 170 440 366 180 6 255 200
PBC-10 16 14421 1330 150.00
inch 4 6 2/3 17 1/3 14 2/5 7 1/4 10 7 7/8
mm 110 180 480 386 190 6 270 212
PBC-10A 17 18021 1220 188.80
inch 4 1/3 7 18 8/9 15 1/5 7 1/2 1/4 10 5/8 8 1/3
mm 120 190 530 406 200 6 285 212
PBC-11 20 23780 1060 239.50
inch 4 5/7 7 1/2 20 6/7 16 7 7/8 1/4 11 2/9 8 1/3
Application
Even torque machines: Centrifugal pumps, blowers, small fans, generators, wire mills, cement mills,
small printing presses, single crank compressors & pumps, hammers, ball & tube mills, rolling mills,
cranes & winches, rock and stone crushers, light machine tools, beaters, exhausters, alternators, textile,
machines
94
Table-3
Power rating (kW):
Speed
PBC 1 PBC 2 PBC 2A PBC 3 PBC 4 PBC 4A PBC 5 PBC 6 PBC 6A PBC 6B PBC 7 PBC 7A PBC 8 PBC 8A PBC 8B PBC 9 PBC 9A PBC 10 PBC 10A PBC 11
rpm
100 0.83 3.24 5.50 6.50 8.60 12.90 17.30 24.50 30.50 37.00 43.50 54.50 60.80 76.00 91.50 104.00 138.50 150.00 188.80 239.50
200 1.63 6.52 10.90 13.00 17.50 26.10 34.80 49.40 61.50 74.00 87.00 108.90 121.90 152.30 182.90 208.00 278.00 302.00 378.00 498.00
300 2.43 9.75 16.40 19.60 26.20 39.00 52.30 74.20 92.20 111.00 130.60 163.40 182.80 228.40 274.30 312.00 417.00 453.00 566.80 746.50
400 3.25 13.00 21.70 26.00 34.90 52.00 69.70 98.80 122.90 148.00 174.00 217.70 243.70 304.50 365.70 417.00 556.00 604.00 756.00 995.50
500 4.10 16.30 27.00 32.60 43.50 65.00 87.00 123.60 153.70 185.00 217.70 272.00 304.60 380.60 457.00 520.00 695.00 755.00 945.00 1244.60
600 4.85 19.60 32.40 39.00 52.40 78.00 104.40 148.30 184.30 222.00 261.00 326.50 365.50 456.50 548.60 624.10 834.10 906.00 1134.00 1493.80
PIX-Pin Bush Couplings
700 5.68 22.80 37.80 45.50 60.90 91.00 121.90 172.90 214.90 259.00 304.60 380.80 426.40 532.70 639.90 728.00 973.00 1057.00 1323.00 1742.90
720 5.83 23.40 39.00 46.90 62.70 93.70 125.40 177.90 221.00 266.60 313.40 391.70 438.70 547.90 658.00 749.00 1001.00 1088.00 1361.00 1792.75
800 6.50 26.00 43.40 52.00 69.70 104.00 139.40 197.70 245.70 296.00 348.00 435.40 487.60 608.90 731.50 832.00 1112.00 1208.00 1512.00 1991.86
900 7.30 29.30 48.70 58.50 78.40 117.00 156.50 223.30 276.00 333.00 391.50 489.70 548.20 684.90 822.70 936.00 1251.00 1359.00 1701.00 2240.96
960 7.80 31.40 52.00 62.50 83.80 124.90 167.00 237.20 294.80 355.20 417.80 522.40 584.70 730.70 877.50 998.00 1334.00 1450.00 1814.00 2390.00
1000 8.00 32.50 54.00 65.00 87.00 130.00 174.00 247.00 307.00 370.00 434.90 544.00 609.00 761.00 914.00 1040.00 1390.00 1510.00 1890.00 2490.00
1200 9.74 39.00 65.00 78.10 104.50 156.00 208.90 296.50 368.50 444.00 522.00 653.00 730.90 913.40 1097.40 1248.00 1668.00 1812.00 2268.00
1400 11.34 45.60 75.70 91.00 121.90 182.00 243.70 345.80 429.90 518.00 609.00 761.70 852.70 1065.00 1280.00
95
1440 11.67 46.90 77.90 93.70 125.40 187.30 260.70 355.80 442.00 532.90 626.50 783.50 877.00 1096.00 1316.00
1600 13.00 52.00 86.50 104.00 139.30 208.00 278.50 395.30 491.00 592.00 696.00 870.50 974.50 1218.00 1462.00
1800 14.60 58.60 97.30 117.00 156.70 234.00 313.30 444.50 552.60 666.00 783.00 979.30
2000 16.30 65.00 108.00 130.00 174.10 260.00 348.00 494.00 614.10 740.00
2200 17.83 71.60 118.90 143.00 191.50 286.00 382.90 543.50 675.50 814.00
2400 19.50 78.00 129.70 156.00 208.80 312.00 417.70
2600 21.08 84.50 140.50 169.00 226.30 338.00 452.50
2800 22.70 91.00 151.30 182.00 243.70 364.00
2880 23.34 93.70 155.60 187.30 250.70 374.50
3000 24.40 97.50 162.00 195.00 261.00 390.00
3500 28.36 113.76 189.00 260.00
4000 32.50 130.00 216.00
4500 36.46 146.25
- PowerWare®
- PowerWare®
Installation
Correct Installation of unique pin bush couplings goes a long way in ensuring satisfactory performance.
Flexible element (rubber bush) is made of rubber reinforced and gives flexibility in all the directions.
Normally only rubber bushes & pins may require replacement. Rubber Bush must be protected against
dripping oil and against the radiation of heat. The bush is fit for ambient temperatures -30°C to +60°C.
Follow below procedure for correct installation of Pin Bush Coupling.
• All components should be cleaned thoroughly, particularly the removal of protective coating in the bore of
hubs. The hubs should be bored true to outer diameter and accurately as per shaft sizes.
• Fit the hubs, do not hammer in hubs – if necessary hubs may be heated in oil up to temperature 200ºC.
Hubs should be normally fitted flush with shaft ends. However, shaft can remain inside hubs provided
enough length is covered by the hubs.
96
- PowerWare®
• Check the parallel and angular alignment using a dial gauge or straight edge at various locations, to achieve
the proper alignment. Necessary shifting/shimming of the equipment may be done.
• It is advisable to recheck alignment and nut tightness after few hours of initial operation. Re-tighten the
bolts, if necessary.
• After mounting, affix a safety cover. Touching this product during operation, may cause injury.
Maintenance
• Check rubber bushes for wear & tear. If worn out/loose, replace the same. Replace pins, if necessary.
• The coupling should be shielded according to safety regulations. These shields/guards should be made
from wire mesh or perforated sheet, if it is not in contradiction with other & prevailing requirements, in
order to ensure adequate ventilation of the coupling.
97
- PowerWare®
PIX Resilient couplings are high potential couplings, which couple the advantage of high power rating as
offered by gear coupling and flexibility properties as exhibited by the flex couplings.
Resilient couplings are easy to install and maintain. Easy construction makes the flexible grids to be easy
replaceable, without having to disconnect, the connected equipment.
Key features:
Highly shock absorbent: Heat treated spring grids absorb shocks, dampens vibration with virtually no
loss of energy.
Flexibility: Coupling provides protection against shock loads owing to the torsional flexibility along the
grid.
Can withstand parallel misalignment: Shearing of tooth grids facilitates sudden jerks absorption and
power transmission even in case of parallel misalignment.
DRIVE DESIGN
Service factor: Determine the required service factor from ‘Table-1’.
Design power: Multiply the normal running power by the service factor. This gives the design power
which is used as a basis for selecting the coupling.
Coupling size: Refer the power ratings from ‘Table-2’ and from the appropriate speed read across, until
a power greater than or equal to that required design power is found. The size of the coupling required
is known from the header of column.
Bore size: From ‘Table-3’, select the appropriate, coupling size with available bore dimension details.
98
- PowerWare®
Generators: Screens:
Even load 1.7 Rotary, coal or sand 2.0
Hoist or rly. service 2.5 Vibrating 3.5
Welder load 2.5
Stoker 1.5
Hammer mill, cement or mines 2.5 Turbo-generator 1.3
Haulage, mining 3.0 Winch, maneuvering:
Kiln, rotary for cement, mining 3.0 Dredge. marine 2.0
Line shaft 2.0 Wood working machinery 1.5
Rubber industry:
Feeders: Mixing mill. refiner 3.0
Apron, Belt, screw-horizontal 1.0 Warming mill 2.5
Table-2
Power rating
Coupling size PRC-01 PRC-02 PRC-03 PRC-04 PRC-06 PRC-07 PRC-08 PRC-09 PRC-10 PRC-11 PRC-13 PRC-14 PRC-15 PRC-17
Rating HP/ RPM 0.006 0.010 0.020 0.030 0.045 0.065 0.095 0.125 0.185 0.355 0.455 0.655 0.905 1.255
Safe speed(rpm) 5650 4750 4450 3400 3200 2950 2500 2150 1900 1800 1650 1550 1350 1200
Appx. Weight(kg) 3 4 5 9 11 15 20 27 43 54 63 72 104 149
99
- PowerWare®
F F
E=Clear diameter
G L1 & L2= Boss length
E L1 L2 H G=Gap
F= Removal space
H=Cover bore
Type-Z PRC
Table-3
Product range
Min. Max. Power
Coupling E L1 L2 F G H Max.
Bore Bore rating
Unit Speed
Size (mm) (mm) (mm) (mm) (mm) (mm) (Kw)at
(mm) (mm) RPM
100 RPM
Application
Agitators, alternators, ball mills, cement mills, conveyors, cranes, crushers, fans, haulages, machine tools,
mixers, motor generators, paper mills, pulp mills, pulverisers, pumps, punching machines, refrigerators,
rolling mills, rubber machinery, steam turbines, textile machinery, traction tube mills, winders
100
- PowerWare®
(PRC-08 Coupling power rating is 0.095 /RPM, therefore, PRC-08 power rating for 1750RPM will be
166.25 HP.
Installation
Mount the seals and the hubs, clean all metal parts using non-flammable solvent and check the hubs, shafts
and keyways for burrs and remove, if necessary. Lightly coat the seals with grease and place well back on the
shafts before mounting the hubs. Mount the hubs on their respective shafts so that each hub face is flush
with the end of the shafts
Align the two hubs so that a straight edge rests squarely on both the hubs and also at various intervals
101
- PowerWare®
Pack the gap and all of the grooves in the two hubs with a specified lubricant before mounting the grid. Fit the
grid over the hubs by starting at one cut end, work the coils of the grid tooth by tooth in one direction and
seat firmly as you go with a soft mallet.
Pack the spaces between and around the grid with as much lubricant as possible and wipe off the excess so
that it is flush with the top of the grid. Position the seals on hubs so that it line up with the grooves in the
flange. Once the coupling is completely assembled, remove both of the lubrication plugs in the cover and
insert a lubrication fitting. Then, pump in the appropriate lubricant, until it is forced out of the opposite
lubrication hole & replace the two lubrication plugs.
Grid removal
Whenever, it is necessary to replace the grid, first remove the cover halves and set aside. Beginning at the
cut end of the grid, carefully insert a screwdriver into the loop. Using the hub teeth for leverage, gradually
pry the grid up, alternating sides while working around the coupling.
• After mounting, affix a safety cover. Touching this product during operation, may cause an injury.
102
Notes
103
Notes
104
Notes
105
PIX Group of Companies
Nagpur & Mumbai, India I Ipswich, Uk
Paderborn, Germany I Dubai, UAE