Professional Documents
Culture Documents
2018 LG Commercial - INSTALASI
2018 LG Commercial - INSTALASI
Technical Setup
Guides LG Commercial Laundry Master Book
Auto-dosing Guide
Step 1. Interface
Connect corresponding wires for the pumps to washer.
Giant-C Pro
Wire Signal
CH Type Discharge Timing
Color Type
① Pre-Wash Red During Pre wash +
② Main Wash Blue Initial inlet during Main wash +
Last 5 minutes during Main wash
③ Bleach Yellow +
(If wash time is set under 7 min, after water inlet)
④ Softener Orange During Final rinse +
⑤ NA NA NA
⑧ - Black (Jump wire) -
Titan-C
Wire Signal
CH Type Discharge Timing
Color Type
ETC
① Red Initial inlet during Main wash +
(Emulsifier)
② Main Wash Blue Initial inlet during Main wash +
Last 5 minutes during Main wash
③ Bleach Yellow +
(If wash time is set under 7 min, after water inlet)
④ Softener Orange During Final rinse +
⑤ Pre-Wash Brown During Pre wash +
⑧ - Black (Jump wire) -
5 4 3 2 1
1 2 3 4 5 8
1
2
3
Giant-C Pro 4
5
1 Skip
4 8
2
3 1 2 3 4 5 8
Skip
Titan-C
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Auto-dosing Guide
Table of Contents
Auto Dosing
Technical Setup
Guides LG Commercial Laundry Master Book
Auto-dosing Guide
+ - + - + - + -
Signal Pumping
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Coin Box Installation
Disassemble the drawer (dispenser), control panel assembly, and top plate assembly.
Assemble coin box to top plate and insert the holder to the hole of side frame (3ea).
Hook up the coin harness to holders carefully (prevent harness from touching the drum).
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Stacking Installation
Stacking kit is
provided in the
upper dryer.
(Loc No.A600
Silver: AGF30609833)
Before stacking, users need to secure enough space for the product,
Including height, and make sure the floor is evened out.
Secure brackets on Top Plate and Front Frame, then reassemble Top Plate (Do not reassemble Control
Panel yet).
Disassemble Control Panel for upper dryer, then assemble the coin selectors on the Panel.
Remove Lower Panel and install it on to Top Frame. Remove legs and its brackets.
Screw the sliding brackets on the base, then stack the machines. Fit the sliding brackets in the slots.
Secure the machines by installing back bracket. Secure bracket on Front Frame of upper dryer.
Assemble security lock to Front Frame with key. Connect coin selectors and display harness.
Reassemble the Control Panels. Assemble security locks to both machines with key.
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Unstacking Guide
You may need to unstack machines to perform service on the lower machine.
Please follow the below guide to unstack the upper dryer.
1. Make sure you have enough room to 2. Unscrew 6 screws on the back bracket
work with the machines and unstack them.
3. Slide the machine so the 4 Sliding Pads line up with the 4 Stacking Bracket entrances on both sides.
The back of the upper dryer should line up with the Top Plate of the bottom machine.
4. Lift the upper dryer straight up with two people and put it down gently.
Perform necessary work, and stack the machines again in reverse order.
(or refer to stacking instructions section in previous pages)
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Overall Installation Guide
Example of Installation
Note
For electrical outlet, use universal outlet and
put grounding wire for EACH machine.
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Airflow Check
Flame Check
1. Check for the blue color of fire for
good airflow and proper burning
2. Check that the flame is not wavering
Static Pressure
Giant dryer: 1.5 cm H₂O / 0.6 inH₂O
Manometer Note
Manometers could have ±0.3cm error
depending on the instrument.
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Recommendations
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Dryer Power Cord Installation
Remove the terminal access cover. Install UL-listed strain relief into power cord hole.
Attach the black & red wires, and the neutral to the center screw of terminal as shown.
Attach power ground wire to (green) ground wire screw.
Remove the terminal access cover. Install UL-listed strain relief into power cord hole.
Remove the terminal access cover and attach the black & red wires as shown.
Attach power ground wire to (green) ground wire screw.
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Clamping Guide
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Gravity Drain Guide
Table of Contents
Technical Guides LG Commercial Laundry Master Book
Leg Stopper
Parts:
Non-skid Pads
Leg Stopper
Step 1. Place non-skid pads under where legs will be, then place leg stoppers
Table of Contents