Professional Documents
Culture Documents
Operating Manual
Version 03/2013
Piston Pumps
Flow Rate 15 cm3 - 30 cm3
B_04119
II 2G IIB c T3 X
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Contents
OPERATING MANUAL
Contents
6 ASSEMBLY AND COMMISSIONING 28
6.1 Transportation 28
6.2 Storage 28
6.3 Assembling the Pump 29
6.4 Grounding 30
6.5 Commissioning 32
6.5.1 Safety Instructions 32
6.5.2 Filling with Separating Agent 34
6.5.3 Basic Flushing 35
7 OPERATION 36
7.1 Filling with Working Material 36
7.2 Work 37
7.2.1 Spraying 37
7.2.2 Pressure Relief/Work Interruption 38
7.2.3 Decommissioning and Cleaning 39
7.3 Long-term Storage 40
8 TROUBLESHOOTING AND RECTIFICATION 41
9 MAINTENANCE 42
9.1 High-pressure Hoses 43
9.2 Decommissioning 43
10 ACCESSORIES 44
11 SPARE PARTS 47
11.1 How Can Spare Parts Be Ordered? 47
11.2 Overview of the Components 48
11.2.1 Components for FineFinish 40-15 48
11.2.2 Components for FineFinish 20-30 49
11.3 Air Motor 50
11.3.1 Reversing Valve 53
11.4 Fluid sections 54
11.4.1 Fluid Section 15 54
11.4.2 Fluid Section 30 56
11.5 Air Regulator Set 58
11.6 Air Regulator Set for AirCoat Air 59
11.7 Trolley, 4" 60
11.8 4-Wheel Trolley 61
12 3+2 YEARS GUARANTEE FOR PROFESSIONAL FINISHING 62
12.1 Scope of Guarantee 62
12.2 Guarantee Period and Registration 62
12.3 Handling 62
12.4 Exclusion of Guarantee 63
12.5 Additional Regulations 63
12.6 CE Declaration of Conformity 65
12.7 Reference to German Regulations and Guidelines 65
4
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
1.1 PREFACE
The operating manual contains information about safely operating, maintaining, cleaning
and repairing the device.
The operating manual is part of the device and must be available to operating and service
staff.
Operating and service staff should be instructed according to the safety instructions.
The device may only be operated in compliance with this operating manual.
This equipment can be dangerous if it is not operated according to the instructions in this
operating manual.
Warning instructions in this operating manual highlight particular dangers to users and
to the device and state measures for avoiding the hazard. These warning instructions fall
into the following categories:
DANGER
Danger - immediate risk of danger. This notice warns you of a hazard!
Possible consequences of not observing the warning instructions.
Non-observance will result in death or serious injury. The signal word indicates the hazard level.
The following are measures which can be taken to prevent the hazard and its
consequences.
5
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
1.3 LANGUAGES
Number of pieces
Position
Marking in the spare parts lists
Order No. Order No.
No. Number
Double stroke
Stainless steel
Two components
6
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
2 CORRECT USE
The device is suitable for processing liquid materials such as paints and varnishes in
accordance with their classification into explosion classes IIA or IIB.
The pneumatic pump can be employed in explosion hazard zones (Zone 1).
WAGNER accepts no liability for any damage arising from incorrect use.
Use the device only to work with the materials recommended by WAGNER.
Only operate the device as a whole.
Do not deactivate safety fixtures.
Use only WAGNER original spare parts and accessories.
The pneumatic pump may only be operated under the following conditions:
The operating staff must be trained on the basis of this operating manual.
The safety regulations listed in this operating manual must be observed.
The operating, maintenance, and repair information in this operating manual must
be observed.
The statutory requirements and accident prevention regulation standards in the
country of use must be observed.
7
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
NOTICE
Abrasive materials and pigments!
Greater wear of parts carrying the material.
The forms of misuse listed below may result in health issues and/or material damage:
use of powder as coating material and
incorrectly set values for processing.
8
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Residual risks are risks which cannot be excluded even in the event of correct use.
If necessary, warning and prohibition signs at the relevant points of risk indicate residual
risks.
9
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
3 IDENTIFICATION
3.1 EXPLOSION PROTECTION IDENTIFICATION
As defined in Directive 94/9/EC (ATEX 95), the device is suitable for use in areas where there
is an explosion hazard.
European Communities
Symbol for explosion protection
Device class II
Category 2 (Zone 1)
Ex-atmosphere gas
Explosion group
Constructional safety
Temperature class: maximum surface temperature < 200 °C; 392 °F
Special Notes (see Chapter 3.2)
3.2 IDENTIFICATION X
10
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Keep this operating manual at hand near the unit at all times.
Always follow local regulations concerning occupational safety and accident
prevention.
Ensure that the device is operated and repaired only by trained persons.
Ensure that the floor in the working area is electrically conductive in accordance with
EN 61340-4-1 (resistance must not exceed 100 Mohm).
Ensure that all persons within the working area wear electrostatically conductive shoes.
Footwear must comply with EN 20344. The measured insulation resistance must not
exceed 100 Mohm.
Ensure that during spraying, persons wear electrically conductive gloves. The grounding
takes place via the spray gun handle.
If protective clothing is worn, including gloves, it has to comply with EN 1149-5. The
measured insulation resistance must not exceed 100 Mohm.
Paint mist extraction systems must be fitted on site according to local regulations.
Ensure that the following components of a safe working environment are available:
– Material/air hoses adapted to the working pressure.
– Personal safety equipment (breathing and skin protection).
Ensure that there are no ignition sources such as naked flames, sparks, glowing wires,
or hot surfaces in the vicinity. Do not smoke.
11
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Always follow the information in these instructions, particularly the general safety
instructions and the warning instructions.
Always follow local regulations concerning occupational safety and accident
prevention.
The spray jet is under pressure and can cause dangerous injuries.
Avoid injection of paint or cleaning agents:
Never point the spray gun at people.
Never reach into the spray jet.
Before all work on the device, in the event of work interruptions and functional faults:
– Switch off the energy/compressed air supply.
– Relieve the pressure from the spray gun and device.
– Secure the spray gun against actuation.
– In the event of functional faults: remedy the fault as described in the "Troubleshooting"
chapter.
The liquid emitters are to be checked for safe working conditions by an expert
(e.g. Wagner Service Technician) as often as necessary or at least every 12 months,
in accordance with the guidelines for liquid emitters (ZH 1/406 and BGR 500 Part 2
Chapter 2.36).
– For shut down devices, the examination can be suspended until the next commissioning.
Carry out the work steps as described in the "Pressure Relief/Work Interruptions"
chapter:
– if pressure relief is required.
– if the spraying work is interrupted or stopped.
– before the device is cleaned on the outside, checked, or serviced.
– before the spray nozzle is installed or cleaned.
In the event of skin injuries caused by paint or cleaning agents:
Note down the paint or cleaning agent that you have been using.
Consult a doctor immediately.
Avoid danger of injury through recoil forces:
Ensure that you have firm footing when operating the spray gun.
Only hold the spray gun briefly in a position.
12
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
In order to avoid electrostatic charging of the device, the device must be grounded.
Friction, flowing liquids, and air or electrostatic coating processes create charges. Flames
or sparks can form during discharge.
Ensure that the device is grounded for every spraying operation.
Ground the work pieces to be coated.
Ensure that all persons inside the working area are grounded, e.g. that they are wearing
electrostatically conductive shoes.
Wear electrostatically conductive gloves when spraying. The grounding takes place via
the spray gun handle.
Ensure that the hose material is chemically resistant to the sprayed materials.
Ensure that the material hose is suitable for the pressure generated in the device.
Ensure that the following information can be seen on the high-pressure hose:
– Manufacturer
– Permissible operating overpressure
– Date of manufacture
Make sure that the hoses are laid only in suitable places. In no case, should hoses be laid
in the following places:
– in high-traffic areas,
– on sharp edges,
– on moving parts, or
– on hot surfaces
Make sure that the hoses are never used to pull or move the equipment.
The electrical resistance of the complete high-pressure hose must be less than 1 Mohm.
Several liquids have a high expansion coefficient. In some cases their volume can rise with
consequent damage to pipes, fittings, etc. and cause fluid leakage.
When the pump sucks liquid from a closed container, ensure that air or suitable gas can
enter the container to avoid a vacuum being generated in the container itself. Thus a
negative pressure is avoided. The vacuum could implode the container (squeeze) and can
cause it to break. The container would leak and the liquid would flow out.
The pressure created by the pump is a multiplication of the inlet air pressure.
13
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
4.2.4 CLEANING
When preparing or working with paint and when cleaning the device, follow the
working instructions of the manufacturer of the paints, solvents, and cleaning agents
being used.
Take the specified protective measures. In particular, wear safety goggles, protective
clothing, and gloves, as well as hand protection cream if necessary.
Use a mask or a breathing apparatus if necessary.
For sufficient health and environmental safety: operate the device in a spray booth or
on a spraying wall with the ventilation (extraction) switched on.
Wear suitable protective clothing when working with hot materials.
14
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
The pneumatic pump may be used in areas subject to explosion hazards. The following
safety regulations must be observed and followed.
Mechanical sparks can form if the device comes into contact with metal.
In an explosive atmosphere:
Do not knock or push the unit against steel or rusty iron.
Do not drop the device.
Only use tools that are made of a permitted material.
Cleaning
If there are deposits on the surfaces, the device may form electrostatic charges. Flames or
sparks can form during discharge.
Remove deposits from the surfaces to maintain conductivity.
Only use a damp cloth to clean the device.
Avoid running the pump so that it sucks in air (without fluid inside). The air, combined with
the vapor of flammable fluids, can generate internal areas with an explosion hazard.
Periodically check that the pump is working smoothly, paying special attention to the
presence of air in the pumped fluid, which may be caused by damaged packings.
Avoid operating the pump with damaged packings.
Ensure that the separating agent container is filled with sufficient separating agent.
15
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
5 DESCRIPTION
5.1 FIELD OF APPLICATION
The pneumatic piston pump is suitable for conveying and processing (AirCoat technique)
liquid materials in accordance with Chapter 5.1.2.
Application
Water-based materials
Solvent-based materials
Low viscosity (<40 sec. DIN No. 4)
Medium viscosity (40 to 60 sec. DIN No. 4)
High viscosity ( >60 sec. DIN No. 4)
UV - sensitive materials
Shear sensitive materials
Humidity sensitive materials
Legend
recommended limited suitability less suitable
NOTICE
Abrasive materials and pigments!
Greater wear of parts carrying the material.
16
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
5.3 DATA
17
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Description Units
* A-rated sound pressure level measured at 1 m distance, LpA1m, in accordance with DIN EN 14462: 2005.
18
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
WARNING
Outgoing air containing oil!
Risk of poisoning if inhaled.
Air motor switching problems.
19
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
mm inch
A 104 4.09
B 108.5 4.27
C 621 24.45
D 276.5 10.89
E 134 5.28
F1 G 1/4"
F2 NPS 1/4"
G M36x2
H1 G 1/4"
H2 8 0.31
I 210 8.27
J 207 8.15
K 86 3.39
A
H1 L 7 0.28
M 182 7.17
N 80 3.15
O 106 4.17
P 96.5 3.8
B Q ø9 ø 0.35
L R ø7 ø 0.28
H2
S 149 5.87
T ø 25 ø1
K
J I
E
F1
F2
Wall mount
S
N
C
R
D
Q
O
G
M M/
B_04120 2
P
20
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
mm inch
A 104 4.09
B 108.5 4.27
C 643 25.3
D 201 7.91
E 134.5 5.3
F1 G 3/8"
F2 NPS 1/4"
G M36x2
H1 G 1/4"
H2 8 0.31
I 210 8.27
J 207 8.15
A K 80 3.15
H1 L 7 0.28
M 182 7.17
N 80 3.15
O 106 4.17
P 96.5 3.8
B Q ø9 ø 0.35
L R ø7 ø 0.28
H2
S 149 5.87
T ø 25 ø 0.98
J K
I
E
F1
F2
S Wall mount
N
T
R
C
Q
O
G M/
M 2
P
B_04100
21
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Example
Stroke frequency /min
BAR
AR
B
BAR B
AR
B
BAR
"?
22
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Air consumption
Material pressure
<2610> <6>
C
120 (12) C 120
<1740> <4>
60 (6) 60
<870> <2>
0 0
0 0.15 0.30 0.45 0.60 0.75 0.90 l/min
C_00054 <0.04> <0.08> <0.12> <0.16> <0.20> <0.24> <gpm>
<1305>
210
C <7.5>
C
60 (6) 140
<870>
<5>
30 (3) 70
<435> <2.5>
0 0
0 0.30 0.60 0.90 1.20 1.50 1.80 l/min
C_00142 <0.08> <0.16> <0.23> <0.31> <0.39> <0.47> <gpm>
23
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
24
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
5.4 FUNCTION
5.4.1 PUMP 11
1
1 Air motor 2
2 Air inlet
3 Mounting flange 8
4 Separating fluid 3
container
5 Material outlet
4 9
6 Fluid section 8
7 Material inlet 10 13
8 Grounding connection 12
6
9 Reversing valve 5
10 Safety valve 14
(air motor ventilation)
11 Air pressure regulator
12 Ball valve B_04121
13 Air outlet to the
reversing valve 7
7
14 Air inlet into the
reversing valve
Function principle
The piston pump is driven with compressed air (11). This compressed air moves the air piston up and down in
the air motor (1) and it also moves the associated pump piston up and down in the fluid section (6). At the end
of each stroke, the compressed air is redirected by a reversing valve (9).
The working material is sucked up during the upwards stroke and is continuously conveyed towards the
material outlet (5) in both stroke directions.
Air motor
The air motor (1) with its pneumatic reverse (9) does not require pneumatic oil.
The compressed air is fed to the motor via an air regulator (11) and the ball valve (12).
The air motor is to be equipped with a safety valve (10) in accordance with Chapter 5.4.3. The safety valve (10)
has been set and sealed at the factory. In case of pressures over and above the permissible operating pressure,
the valve, which is held with a spring, automatically opens and releases the excess pressure.
WARNING
Overpressure!
Risk of injury from bursting components.
OPERATING MANUAL
1 Pressure regulator
2 Ball valve
3 Pressure gage (air inlet pressure)
4 Pressure gage for AirCoat air (option)
5 Compressed air inlet
6 Pressure regulator AirCoat (option)
7 Safety and motor pressure relief valve
2 3 1 4 6 2 3 1
7 5
7
B_04122
B_04123
26
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Safety valve
The safety valve (10) has been factory adjusted so as to ensure that if pressure exceeds the
permitted operating pressure, the valve, which is held with a spring, automatically opens
and releases the excess pressure.
As well as handling pressure limits, the valve is also used as a pressure relief valve for the
air motor.
10
Pressure relief of the air motor:
10
1 Close ball valve (2). 2
2 Pull back the ring on the safety
valve (10) and hold it there until
the pressure in the air motor has
been equalized.
B_04124
WARNING
Overpressure!
Risk of injury from bursting components.
1 Material outlet 2
2 Return valve 1
B_04075
3 Material return line
3
27
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
6.1 TRANSPORTATION
6.2 STORAGE
WARNING
Discharge of electrostatically charged components in atmospheres
containing solvents!
Explosion hazard from electrostatic sparks.
28
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Example:
Notice
Airless system
This pump can be used as part of a spraying system for Airless
or AirCoat applications. Individual supplement components
for this pump can be found in the Wagner Accessories
Catalogue, or can be put together with the Spraypack 3
Configurator. The nozzles must be selected according to the 6
gun instructions. In the case of spraypack orders, the pumps 1
(1) are already pre-mounted on a trolley (6) or on a stand at 2
the factory. 8 4
Procedure:
1 6
2
8 4
5
B_04077
WARNING
Inclined ground!
29
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
6.4 GROUNDING
WARNING
Discharge of electrostatically charged components in atmospheres
containing solvents!
Explosion hazard from electrostatic sparks.
WARNING
Heavy paint mist if grounding is insufficient!
Danger of poisoning.
Insufficient paint application quality.
R max < 1 MΩ
Paint container
B_00304
Floor, electrostatically conductive
30
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Pump 4 mm2;
Paint container 6 mm2;
Conveyor 16 mm2;
Spray booth 16 mm2;
Spraying stand 16 mm2;
Procedure:
Grounding cable
B_04127
31
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
6.5 COMMISSIONING
Before carrying out any work, the following points must be observed in accordance with
the operating manual:
- Observe all safety regulations in accordance with Chapter 4.
- Carry out commissioning properly.
WARNING
High-pressure spray jet!
Danger to life from injecting paint or solvent.
WARNING
Toxic and/or flammable vapor mixtures!
Risk of poisoning and burns.
WARNING
Gas mixtures can explode if there is an incompletely filled pump!
Danger to life from flying parts.
Ensure that the pump and suction system are always completely
filled with flushing agent or working medium.
Do not spray the device empty after cleaning.
32
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Before every start-up, the following points should be observed as laid down in the
operating manual:
- Check the permissible pressures.
- Check all connecting parts for leaks.
- Check hoses for damage.
It should be ensured that the device is in the following state before carrying out any work
on it:
- Interrupt the air supply (2).
- Depressurize the air motor (pull the ring on the safety valve (10)).
- Relieve the pressure from the fluid section.
10
closed
10
2 open
C_00157
B_04124
EMERGENCY STOP
2
In the case of unforeseen occurrences
the ball valve (2) should be closed
immediately.
Open the safety valve (10) and relieve the
material-conveying parts completely of
pressure via the return valve (3).
B_04078
3
33
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
NOTICE
Piston pump runs dry!
High wear/damage to the packings.
Paint or solvent can escape if the seals are dry.
Ensure that the separating agent container is filled with sufficient separating agent.
Filling level 2 cm; 0.8 inch under the cup edge.
Notice
Maximum permissible inclination of pump for moving, transportation
etc. after filling it with separating agent ± 30°.
The pump must be vertical during operation.
B_04130
34
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Before each basic flushing, the nozzle must be removed from the pistol. The data in the
gun's operating manual are to be observed.
With AirCoat systems, carry out the basic flushing of the system without atomizing air (8).
1 Place empty container (5) under return tube (4).
2 Place suction hose (7) in the container with flushing agent (6).
3 Open return valve (3).
4 Slowly open the ball valve (2).
5 Adjust the air pressure on the pressure regulator (1) so that the pump runs smoothly.
6 Flush the system until clean flushing agent flows into the container (5).
7 Close ball valve (2).
8 Close return valve (3).
9 Point the gun (9), without nozzle, into container (5) and open it.
10 Slowly open the ball valve (2).
11 Rinse until clean flushing agent flows from the gun.
12 Close ball valve (2).
13 Relieve the system pressure, either by opening the return valve (3) or via the trigger
on the gun (9).
14 When there is no pressure remaining in the system, close the gun (9) or the return
valve (3).
15 Secure the gun.
16 Dispose of the contents of the container (5) according to the local regulations.
closed 1 8
2
open
3
4
6
9
5
B_04079
35
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
7 OPERATION
7.1 FILLING WITH WORKING MATERIAL
Note:
Before each filling, the nozzle must be removed from the pistol. The data in the gun's
operating manual are to be observed.
In case of AirCoat systems, carry out the filling of the system without atomizing air (8).
36
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
7.2 WORK
7.2.1 SPRAYING
closed 1 8
2
open
9
3
4
B_04080
1 Secure the gun and insert the nozzle into the gun.
2 Close return valve (3).
3 Slowly open the ball valve (2).
4 Set required working pressure on the pressure regulator (1).
5 Optimize the spraying results according to the data in the gun operating manual.
6 Start work process.
37
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
10
10
2
B_04124
NOTICE
Hardened working material in the spraying system when two-component material
is processed!
Destruction of pump and injection system.
Follow the manufacturer‘s processing rules, particularly regarding the pot life.
Flush thoroughly before the end of the pot life.
The pot life is decreased by warmth.
38
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Notice
The device should be cleaned for maintenance purposes. Ensure that no remaining
material dries and sticks.
Procedure:
1 Carry out pressure relief of the material and air -> Chapter 7.2.2.
2 Basic cleaning -> carry out the steps in Chapter 6.5.3.
3 Maintain the gun according to the operating manual.
4 Clean and check the suction system and the suction filter.
5 Clean the outside of the system.
WARNING
Brittle filter pressure regulator!
The container on the filter pressure regulator becomes brittle
through contact with solvents and can burst.
Flying parts can cause injury.
WARNING
Gas mixtures can explode if there is an incompletely filled
pump!
Danger to life from flying parts.
Ensure that the pump and suction system are always completely
filled with flushing agent or working medium.
Do not spray the device empty after cleaning.
39
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
When storing the device for longer periods of time, it is necessary to thoroughly clean it
and protect it from corrosion. For the last rinse, replace the water or solvent in the material
pump with a suitable preservative. Fill separating agent cup with separating agent. Store
pump vertically.
Procedure:
1 Chapter 7.2.3 "Decommissioning and Cleaning", perform points 1 to 7.
2 Flush with preservative according to Chapter 6.5.3 and paint supplier's instructions.
3 If the discharge duct is to be removed, seal material outlet with plug.
4 If the suction system is to be removed, seal material inlet with plug.
40
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
If none of the causes of malfunction mentioned are present, the defect can be remedied by a WAGNER Service
Center.
41
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
9 MAINTENANCE
WARNING
Incorrect maintenance/repair!
Danger to life and equipment damage.
1 Check the level of separating agent in the separating agent cup every day, and top
up if necessary.
2 Check and clean the high pressure filter every day or as required (if available).
3 Every decommissioning should be carried out as laid down in Chapter 7.2.3!
4 Check hoses, pipes, and couplings every day and replace if necessary.
In accordance with the guideline for liquid emitters (ZH 1/406 and BGR 500 Part 2
Chapter 2.36):
- The liquid emitters should be checked by an expert (e.g. Wagner service technician)
for their safe working conditions as required and at least every 12 months.
- If devices have been decommissioned, the examination can be suspended until
the next start-up.
42
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
The service life of the fluid hoses is reduced due to environmental influences even when
handled correctly.
Check hoses, pipes, and couplings every day and replace if necessary.
As a precaution, fluid hoses should be replaced after a period specified by the
operator.
DANGER
Bursting hose, bursting threaded joints!
Danger to life from injection of material.
9.2 DECOMMISSIONING
When the equipment must be scrapped, please differentiate the disposal of the waste
materials.
The following materials have been used:
Steel
Aluminum
Elastomers
Plastics
Carbide
43
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
10 ACCESSORIES
Accessories
Designation Order No. Order No.
1 Pump PE/T 2329450 2329452
2 AirCoat regulator set T6145.00A
3 Grounding cable, complete 3 m; 9.8 ft 236219
4 Separating agent 250 ml 9992504
5 Separating agent 500 ml 9992505
44
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
2
x
x
1
11 4/5
12
13
14
18
15 16
17
19
B_04081
45
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
21
22
23
24
B_04113
46
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
11 SPARE PARTS
11.1 HOW CAN SPARE PARTS BE ORDERED?
Always supply the following information to ensure delivery of the right spare part:
The following information is also required to ensure smooth processing of your order:
- Billing address
- Delivery address
- Name of the person to be contacted in the event of any queries
- Type of delivery (normal mail, express delivery, air freight, courier, etc.)
Explanation of column " " (labeling) in the following spare parts lists:
Wearing parts
Note: No liability is assumed for wearing parts.
WARNING
Incorrect maintenance/repair!
Risk of injury and equipment damage.
47
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
13
3
12
8
20 Nm; 14.7 lbft 9
1 4
6
5
11
2
10
30 Nm; 22.1 lbft
B_04135
48
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
13
3
12
1 10 14
30 Nm; 22.1 lbft
6 4
5
7
B_04115 11
30 Nm; 22.1 lbft
49
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
WARNING
Incorrect maintenance/repair!
Risk of injury and equipment damage.
OPERATING MANUAL
30 Nm; 22 lbft
28
2
29
16 4
9 29
13
30
4.5 Nm; 3.3 lbft
7
14
29
11 29
1
10 13
3 36
29
17 35
32
15 33 31
34
22 24
27 19
20 Nm; 14.7 lbft 27
29 25
18 23
Installation instructions:
Mount piston rod (12) always
12 from bottom to top by the
assigned rod seal (18).
20
21
B_04347 20
51
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
WARNING
Incorrect maintenance/repair!
Risk of injury and equipment damage.
52
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
3
B_03139
53
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
35
33
13
7 14
19
15
30 10
17
34
35 16
31
18
B_03445
32
54
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
55
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
2 41
3 21
22
42
5
6
7
8
42 7 23
8
10 24
7
8 25
7
8 26
42
9 27
29
11 26
12 27
1 45
42 28
14
30
15
42
16 31
13
45 44
32
33
17 34
35
18
36
19
43 20
37
B_04116
56
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
OPERATING MANUAL
14
14 9 4
14 5
14 8
1
2 13
14 10 3
11
12
B_04117
58
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
7
6
4 7
5
1
3
B_03436 2
Spare parts list for air regulator set for AirCoat Air
59
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
15
5 17
10
13
4
14
2
5 16
6
3 1
A 7 8
Distance
11 12 B_04074
OPERATING MANUAL
4
12
3
2
8
13
5
1
6
10
9
11
B_03439
14
61
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
The guarantee period amounts to 36 months. For industrial use or equal wear, such as shift
operations in particular, or in the event of rentals, it amounts to 12 months.
Systems driven by petrol or air are also guaranteed for a 12 month period.
The guarantee period begins with the day of delivery by the authorized specialist shop.
The date on the original purchase document is authoritative.
For all products bought in authorized specialist shops from 2009-02-01 the guarantee
period is extended to 24 months providing the buyer of these devices registers in
accordance with the following conditions within 4 weeks of the day of delivery by the
authorized specialist shop.
Registration can be completed on the Internet at
The guarantee certificate is valid as confirmation, as is the original purchase document
that carries the date of the purchase. Registration is only possible if the buyer agrees to the
data that is entered during registration being stored.
When services are carried out under guarantee the guarantee period for the product is
neither extended nor renewed.
Once the guarantee period has expired, claims made against the guarantee or from the
guarantee can no longer be enforced.
12.3 HANDLING
If defects can be seen in the materials, processing, or performance of the device during the
guarantee period, guarantee claims must be made immediately, or at the latest within a
period of 2 weeks.
The authorized specialist shop that delivered the device is entitled to accept guarantee
claims. Guarantee claims may also be made to the service centers named in the operating
manual. The product has to be sent without charge or presented together with the
original purchase document that includes details of the purchase date and the name of
the product. In order to claim for an extension to the guarantee, the guarantee certificate
must be included.
The costs as well as the risk of loss or damage to the product in transit or by the center that
accepts the guarantee claims or who delivers the repaired product, are the responsibility
of the customer.
62
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
The above guarantees apply exclusively to products that have been bought from authorized
specialist shops in the EU, CIS, Australia and are used within the reference country.
If an inspection finds damage not covered by the present guarantee, repairs are carried out
at the expense of the buyer.
The above regulations manage the legal relationship to us concludingly. Additional claims,
in particular for damages and losses of any type, which occur as a result of the product
or its use, are excluded from the product liability act except with regard to the area of
application.
Claims for liability for defects to the specialist trader remain unaffected.
German law applies to this guarantee. The contractual language is German. In the event
that the meaning of the German and a foreign text of this guarantee deviate from one
another, the meaning of the German text has priority.
Germany
63
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
64
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
Herewith we declare that the supplied version of pneumatic pumps and their spraypacks
FineFinish
Identification:
II 2G IIB c T3 X
EC Certificate of Conformity
The CE certificate of conformity is enclosed with this product. If needed, further copies
can be ordered through your WAGNER dealer by specifying the product name and serial
number.
Order number: 2312813
Note: All titles can be ordered from Heymanns Publishing House in Cologne, or they can
be found on the Internet.
65
VERSION 03/2013 ORDER NUMBER DOC 2310799
OPERATING MANUAL
66
ED
FI
I
CERT
A DK GB
Tel.
Fax Tel.
Fax Fax
B E I
CH F NL
Tel. Tel.
Fax Tel. Fax
Fax
D CZ S
Tel.
Fax Tel.
Fax
Tel. +49 / 75 44 / 505 -1664
Fax