Professional Documents
Culture Documents
Important safeguards.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your NutriBullet®. When using any
electrical appliance, basic safety precautions should always be
observed, including the following important information.
WARNING!
ingredients in your pitcher carefully. Use care when
without the pitcher lid and handling any blade. To
vented lid cap attached and avoid laceration injury, do
locked. The vented lid cap not handle or touch any
allows steam and pressure blade edge.
to escape, while guarding
against excess splashing. AVOID CONTACT WITH
MOVING PARTS! Keep
Before blending hot hands and utensils out of
ingredients, carefully examine and away from blades
the pitcher lid to make while blending food to
sure the vent slots are not reduce the risk of severe
obstructed or blocked. personal injury. Only use the
provided tamper to direct
When blending hot liquids, ingredients to the blades.
add liquid and solid • After blending, turn the
ingredients to your pitcher unit off. Wait to remove the
below their respective MAX pitcher from the motor base
lines. Attach the pitcher until the blades come to a
lid with the vented lid cap full stop and the unit powers
inserted and locked. Press down completely. Taking the
POWER and begin blending vessel off the unit prior to
by selecting the desired complete power down can
program or if you are using cause damage to the blade
manual speeds, start blending coupling or motor gear.
on the LOW setting. Once
ingredients are integrated, Never use the NutriBullet®
adjust speed as needed. Smart Touch Blender™
without adding liquid, as
If the NutriBullet® blends
for longer than one minute, doing so may damage
friction from the blades can the blades.
cause ingredients to heat and • The cyclonic action® of your
generate internal pressure NutriBullet® Smart Touch
inside the vessel. If a blending Blender™ requires the use
vessel becomes warm to the of liquids to make smoothies
touch, turn off the machine and other nutritious items.
and allow the vessel to cool The NutriBullet® Smart Touch
3
Blender™ is not intended to • If you need to push ingredients
be used without liquids, or as closer to the blade, ONLY USE
an ice crusher. ALWAYS ADD THE TAMPER PROVIDED with
LIQUID to your recipe. the NutriBullet® Smart Touch
Blender™ configuration.
• DO NOT USE the NutriBullet®
DO NOT use any apparatus
Smart Touch Blender™ for
other than the tamper to push
grinding dry ingredients such
ingredients toward the blade.
as grains, cereal, or coffee, as
The tamper is specifically
this may damage the motor
designed not to come in
and blade.
contact with the blade.
PITCHER SAFET Y Spatulas, spoons and other
tools can make contact with
• Pitcher lid must be locked onto the blade, which may result
the pitcher in order to operate in damage to the machine,
the unit. damage to property, and
possible injury.
• With recipes that require
certain ingredients to be • NEVER USE YOUR FINGERS
incorporated during blending, OR ANY PART OF YOUR HAND
first add the base ingredients, TO PUSH INGREDIENTS
seal the pitcher lid with vented DOWN TOWARD THE BLADE.
lid cap attached, and begin Only use the provided tamper.
blending. Then, once the
ingredients are well mixed, ELECTRICAL SAFET Y
twist open the vented lid cap
and carefully pour or drop Do not use this product
WARNING!
WARNING!
handle the NutriBullet® Smart
Touch Blender™ until all parts been blended at room
have stopped moving. temperature or cooler
(21°C/70°F or less), transfer
• To unplug, grasp the plug and mixture to a stove top
pull from the outlet. Never pull pot to heat. Always use a
from the power cord. thermometer to test the
internal temperature of
• Do not let cord hang over
cooked ingredients; they may
edge of table or counter,
feel cool to the touch, yet still
or touch hot surfaces. Do be hot inside.
not pull, twist, or damage the
power cord. Do not allow the The NutriBullet® Smart Touch
cord to touch hot surfaces, Blender™ is not intended for
including the stove. use on the stove top. Do not
place the motor base or any
• The Smart Touch Blender™ NutriBullet® accessory on the
is ready to operate when stove or immerse in boiling
unit is plugged in and power water. This may result in
icon is illuminated. Avoid damage to the accessory.
inadvertent contact with the
touch screen display. • Do not place any of the
NutriBullet® Smart Touch
• If the motor stops working, Blender™ parts in a
unplug the motor base and let microwave, oven, in a stove
it cool for at least 15 minutes top pot, or immerse in boiling
before attempting to use water, as this may result in
it again. Your NutriBullet® damage to the part.
Smart Touch Blender™ has
an internal thermal breaker • Do not place on or near a hot
that shuts off the motor when gas or electric burner, or in a
it overheats. The thermal heated oven.
breaker will reset when the unit
5
VENTILATION WARNINGS • Avoid blending the following
seeds and pits, as they contain
• To prevent a fire hazard, power a chemical known to release
base openings (underneath cyanide into the body when
the motor base) should be ingested: apple seeds, cherry
free of dust or lint and never pits, plum pits, peach pits, and
obstructed with flammable apricot pits. Fruit pits may also
materials such as newspapers, cause damage to the pitcher.
tablecloths, napkins, dish
towels, place mats or other ADDITIONAL
similar type materials.
INSTRUCTIONS FOR
• CAUTION! Always operate PROPER USAGE .
the NutriBullet® Smart Touch
Blender™ on a level surface, • TO AVOID LEAKAGE, DO NOT
leaving unobstructed space OVERFILL THE PITCHER!
beneath and around the motor Your pitcher is marked
base to permit proper air with two MAX lines: one for
circulation. Vents on the bottom solid ingredients (higher
of the product are provided for line) and one for liquids
ventilation to ensure reliable (lower line). When filling the
motor operation and to blender, make sure your
prevent overheating. ingredients do not exceed
their respective MAX lines.
MEDICAL SAFET Y Exceeding either MAX line
can result in leakage, and
• The information contained in
may lead to dangerous
the User Guide and Recipe
pressurization, which can
Guide is not meant to replace
cause the vessel and blade
the advice of your physician.
assembly to separate,
Always consult your physician
potentially resulting in
regarding health and
personal injury and/or
nutrition concerns. property damage.
MEDICATION INTERACTIONS:
• The pitcher is specific to the
• If you are taking any exact model of NutriBullet®
medication, especially Smart Touch Blender™ you
cholesterol-lowering possess. Use of incompatible
medication, blood parts (parts from other
thinners, blood pressure models) may result in
drugs, tranquilizers, or damage to your NutriBullet®
antidepressants, please check Smart Touch Blender™ or
with your physician before create safety hazards. When
trying any of the recipes ordering replacement parts
contained in this user guide or on nutribullet.com or via
recipe guide. customer service, please
6
specify the machine model to Never purchase after market
ensure you receive parts that parts for your NutriBullet.
are compatible with your unit. Always use genuine NutriBullet
• Always use genuine replacement parts.
!
NutriBullet® replacement
parts. After market parts are
Save these
instructions!
not made to NutriBullet’s
specifications and may
damage your unit or cause
serious injury. If you have any comments,
• Periodically inspect all questions, or concerns, please
NutriBullet® components go to nutribullet.com.
for damage or wear that Or call customer service at:
may impair proper function 1 (800) 523-5993.
or present an electrical
hazard. Make sure that the
power cord and plug are
undamaged. Discontinue
use and replace blending
vessels if you detect cracking,
cloudiness, or damage to
the plastic. Ensure that the
blades rotate freely and that
the structure is undamaged.
Make sure that the motor
base is unobstructed and
clean. Follow maintenance
recommended in the User
Guide and never operate
your NutriBullet® with
damaged components.
If your NutriBullet®
malfunctions in any way,
immediately discontinue use
and contact customer service
at 1 (800) 523-5993.
7
8
Contents.
10 What’s included
11 Assembly guide
12 Getting started
12 Safety guide
12 Pitcher assembly & use
16 Blending control panel
16 Manual speeds
18 Intelligent programs
20 Care & maintenance
20 How to clean the NutriBullet®
21 How to store
21 Replacement parts
22 NutriBullet® Smart Touch Blender™
one-year limited warranty
25 Warranty registration
9
What’s included.
10
Assembly guide.
vented lid cap
pitcher lid
easy-pour spout
tamper
pitcher
integrated blade
motor base
11
Getting started.
PLEASE KEEP Steam and splatters can escape
WARNING!
through the vented lid, potentially
THESE IMPORTANT causing scalding and/or burns.
SAFEGUARDS IN NEVER blend hot liquids in your
pitcher without the pitcher lid
MIND WHEN USING and vented lid cap attached. The
THE APPLIANCE: vented lid cap is ventilated to allow
steam and pressure to release,
• Make sure the base is plugged in while guarding against excess
for use. splashing. NEVER blend hot liquids
in your NutriBullet cups or any
• Never run the appliance while empty.
other sealed vessel.
• Appliance accessories are not
When blending hot liquids, add
intended to be used in the microwave
liquid and solid ingredients to your
as it may damage the accessories.
vented pitcher below their respective
• Never leave the appliance MAX lines. Attach the pitcher lid
unattended while in use. with the vented lid cap inserted.
Press POWER , then select desired
program or begin blending on
LOW setting. Once ingredients are
integrated and the mixture is level
(no splashing), increase speed
Use extra caution when as needed.
blending hot liquid or
ingredients in the pitcher. Always use care when opening
the pitcher lid after blending hot
ingredients making sure that excess
pressure has been released.
Pitcher assembly
& use.
Review all warning and caution
statements in the Important Safeguards
section (pg 2-7) and on the previous 1
page before proceeding to Step 1.
Place the motor base on
a clean, dry, level surface
such as a counter or table.
12
2 3
Place the pitcher on a Place the lid on top of the
clean, dry, level surface. pitcher and press down firmly
Add the ingredients to the until locked in place. Place the
pitcher, making sure they do lid cap over the lid opening,
not exceed the MAX line. then press down and twist
until locked in place.
NOTE: The blending pitcher is
marked with two MAX lines: one for NOTE: The motor will not run unless
solid ingredients (higher line) and the lid is locked in place.
one for liquids (lower line). When
filling the blender, make sure your
ingredients do not exceed their
respective MAX lines.
5
4 Plug the power cord into
an electrical outlet and
Place the pitcher (lid-side up) press POWER to turn
onto the motor base and twist on the blender. Once the
clockwise to lock it into place. pitcher is fully locked and
When you hear the click, it’s the unit is plugged in, the
locked and ready to blend. Blending Control Panel will
illuminate and the unit will
NOTE: You may need to twist the be ready to operate.
pitcher slightly until you feel
it settle into the grooves on top of NOTE: If pitcher lid and pitcher are
the base. not fully secured onto the base,
control panel will not illuminate.
13
NOTE: If you need to add
additional ingredients while
blending, switch the setting to
LOW and remove the lid cap
from the pitcher lid, leaving the
lid attached. Add ingredients
through the hole in the top
of the lid, followed by the
tamper if necessary. Replace
the lid cap, then increase to
your desired speed. DO NOT
attempt to add items through
the vent hole when blending
HOT ingredients.
6
To begin blending, select
a manual speed or
program on the Blending
Control Panel. To pause
blending, press the current
speed or program once,
the unit will stop running
and the timer will pause. To
resume blending, press a
manual speed or the same
program again.
CAUTION: Do not use any
NOTE: Go to the blending control apparatus other than the
panel section on pages 16-19 for tamper to push ingredients
speed and program definitions, toward the blade. The tamper
images, and other information. is specifically designed not to
come in contact with the blade.
Spatulas, spoons and other
tools are long enough to reach
the blade, which may result
in damage to the machine,
damage to property, and
possible injury.
14
7 8
When you have reached your Twist pitcher counterclockwise
desired consistency, stop and lift off the motor base.
the appliance by pressing Pour and enjoy!
POWER . If you are using
a program, you will hear WARNING: Blades are sharp. Never
insert your hands into the pitcher.
a beep when the program
has completed. Wait for the
blades to stop turning. The
unit will enter idle-mode.
The timer will reset and the
Blending Control Panel will
remain illuminated. Press
POWER again to turn off
the unit completely and the
illuminated display will
turn off.
NOTE: Press up with your thumb on
the tab near handle first to loosen
pitcher lid for easy removal!
15
Blending control panel:
manual speeds.
TURNING ON/OFF
The power button controls the
master power of the appliance.
When pitcher with pitcher lid
is locked in place, pressing
POWER will indicate the motor
is powered on and the Blending
Control Panel will illuminate.
TIMER
When using a blending speed:
timer starts at zero (00:00) and
increases during operation,
showing time elapsed since
blending began. When using
program presets: timer counts
down during operation until
program is completed.
PULSE
Use to control chopping
and processing.
LOW SPEED
Use to mix thin batters,
gravies and marinades. Or, to
scramble eggs, process cooked
foods and uncooked fruits.
16
MEDIUM SPEED
Use to cream soups, blend
sauces and spreads, or mix dips.
Also great for grinding nuts,
making mixed drinks, powdered
drinks or milkshakes.
HIGH SPEED
Use to liquefy thick mixtures
and extract frozen fruits and
vegetables into smoothies.
17
Blending control panel:
intelligent programs.
PURÉES
Delivers a perfectly smooth
texture — ideal for dips, sauces
and spreads of all kinds.
SOUPS
Blends sweet or savory
ingredients into the silkiest of
ready to heat soups and
chilled gazpachos.
FROZEN DRINKS
Perfect for ice-blended
mocktails or cocktails, and
frappe style drinks.
SMOOTHIES
Easily turn fresh or frozen fruits
and vegetables into sippable
nutritious smoothies.
18
TO SELECT A PROGRAM
Press the desired program to Our intelligent programs are
turn on. The selected program expertly designed to give you
will illuminate and the rest of the perfect results every time.
the blending control panel During each program, the unit
will disappear. The program may pulse, change speeds,
will start to run, and timer will and blend as needed until the
countdown until the program is program is complete.
complete. When the program
is complete, there will be NOTE: If the unit stops running and
an audible alert and main power and timer display are flashing,
blending control panel will your device may be overheated.
Unplug your device and wait 15 minutes.
be illuminated. To pause a
Plug back in to reset.
program before completion,
press the active program. The
motor will stop and the timer
will pause counting. To resume
the program, press the program
button again. To return to main
blending control panel, press
POWER once. To fully power
down, press POWER twice and
unplug the unit.
19
Care & maintenance.
Here’s how to clean • Do not attempt to remove any
pieces from the motor base.
the NutriBullet®:
• Use a sponge or dish cloth
STEP 1: dampened with warm soapy
water to wipe down the
The most important thing —
motor base until clean.
ALWAYS POWER OFF THE UNIT
and UNPLUG the motor base • To clean leakage residue
from the power outlet when it from the motor base, wipe
is not in use. Do not attempt to with a damp sponge and
handle the appliance until all warm water.
parts have stopped moving!
• If necessary, you may use
This includes during assembly
a small brush to scrub the
and disassembly, while
actuator system area to
changing accessories during
ensure it’s clean.
cleaning, and any time you
leave the machine unattended. WARNING: Never submerge
the motor base in water.
STEP 2:
NUTRIBULLET ® PITCHER:
Detach the pitcher from the WARNING: Blades are sharp!
motor base. Use caution when cleaning
the pitcher.
STEP 3:
• The pitcher is top-rack
Clean the individual dishwasher-safe. We
components (motor base, recommend rinsing and
pitcher) as recommended on briefly scrubbing it with a
the following pages. dish brush to remove any
remaining debris before
MOTOR BASE: placing in the dishwasher.
NEVER use the sanitize cycle
• To avoid risk of injury, NEVER
to wash the pitcher — heat
attempt to clean the actuator
this high can warp the plastic.
system on the motor base
while the NutriBullet® Smart • If preferred, hand-wash the
Touch Blender™ is plugged in. pitcher with soap and water.
Stuck-on ingredients might
require extra scrubbing
20
from a dish brush or sponge. How to store:
The blades are sharp. Use
caution to not touch blades Store the NutriBullet® pitcher
while hand-washing pitcher. upright with the pitcher lid
• Regularly check the secured on top. Do not place
structure of the pitcher and anything on top of the pitcher
twisting threads for cracking, lid. Store remaining pieces in a
crazing, or breakage. safe place where they will not
If damaged, replace be damaged and won’t
immediately to prevent cause harm.
possible personal injury.
TAMPER
Replacement parts.
To order additional parts and accessories, please visit our website
at nutribullet.com/shop/accessories or feel free to contact
customer service: 1 (800) 523-5993.
21
NutriBullet® Smart
Touch Blender™ one-
year limited warranty.
22
customer service department This limited warranty applies
you will be asked for your to consumer use only, and
name, address, telephone is void when the product
number and to provide proof of is used in a commercial or
the original purchase (receipt) institutional setting.
containing a description of the
product(s), purchase date, and This limited warranty extends
the appropriate NutriBullet® only to the original consumer
serial number(s). Before you purchaser and is not
send your product for limited transferable. In addition, proof of
warranty service please make purchase must be demonstrated.
sure to keep a copy of all
relevant documents for your Repair or replacement of
files (receipt, etc.). It is always the product (or, if repair or
recommended to purchase replacement is not feasible, a
product insurance and tracking refund of the purchase price)
services when sending your is the exclusive remedy of the
product for service. Remember, consumer under this limited
shipping and processing fees warranty. NutriBullet, LLC shall
will be incurred and are not not be liable for any incidental
covered by the one-year or consequential damages for
limited warranty. breach of this limited warranty
or any implied warranty on
EXCLUSIONS & LIMITATIONS this product.
This NutriBullet® One-Year
This limited warranty gives
Limited Warranty applies only to
you specific legal rights, and
NutriBullet® products distributed
you may also have other rights
by or for NutriBullet® that can
which vary from state to state.
be identified by the “NutriBullet”
NutriBullet® is not liable for
trademark, trade name, logo
any damage to products not
and bar code. NutriBullet®
covered by this warranty (e.g.,
Smart Touch Blender™ One-
cups, book, User Guide).
Year Limited Warranty does not
apply to any other products that
This limited warranty does not
may appear to be authentic,
apply: (a) to damage caused
but were not distributed/sold by
by accident, abuse, misuse,
NutriBullet, LLC.
or misapplication; (b) to
damage caused by improper
Normal wear and tear is not
maintenance (including
covered by this limited warranty.
unauthorized parts service);
23
(c) to a product or a part that NUTRIBULLET IS NOT
has been modified in any way; RESPONSIBLE FOR DIRECT,
(d) if any NutriBullet® serial SPECIAL, INCIDENTAL OR
number or trademark has been CONSEQUENTIAL DAMAGES
removed or defaced; and or (e) RESULTING FROM ANY
if the product has been used BREACH OF WARRANTY
with an adapter/converter. OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY,
THIS LIMITED WARRANTY INCLUDING BUT NOT LIMITED
AND THE REMEDIES SET TO LOST PROFITS, DOWNTIME,
FORTH ABOVE ARE EXCLUSIVE GOODWILL, DAMAGE TO
AND IN LIEU OF ALL OTHER OR REPLACEMENT OF
WARRANTIES, REMEDIES EQUIPMENT AND PROPERTY.
AND CONDITIONS, WHETHER NUTRIBULLET® SPECIFICALLY
ORAL OR WRITTEN, EXPRESS DOES NOT REPRESENT THAT
OR IMPLIED. NUTRIBULLET® IT WILL BE ABLE TO REPAIR
SPECIFICALLY DISCLAIMS ANY ANY PRODUCT UNDER THIS
AND ALL IMPLIED WARRANTIES, LIMITED WARRANTY.
INCLUDING, WITHOUT
LIMITATION, WARRANTIES Some states and provinces
OF MERCHANTABILITY AND do not allow the exclusion
FITNESS FOR A PARTICULAR or limitation of incidental
PURPOSE. IF NUTRIBULLET or consequential damages
CANNOT LAWFULLY DISCLAIM or exclusions or limitations
IMPLIED WARRANTIES UNDER on the duration of implied
THIS LIMITED WARRANTY, warranties or conditions,
ALL SUCH WARRANTIES, so the above limitations or
INCLUDING WARRANTIES exclusions may not apply to
OF MERCHANTABILITY AND you. This warranty gives you
FITNESS FOR A PARTICULAR specific legal rights, and you
PURPOSE ARE LIMITED IN may also have other rights
DURATION TO THE DURATION that vary by state or province.
OF THIS LIMITED WARRANTY.
No NutriBullet® reseller, agent, or
employee is authorized to make
any modification to this warranty.
24
Warranty registration.
Please visit nutribullet.com/
warranty-registration or call
1 (800) 523-5993 to register
your new NutriBullet® Smart
Touch Blender™. You will
be asked to enter the Serial
Number* of your product, along
with the purchase date and
place of purchase.
25
1 (800) 523-5993 | nutribullet.com
Illustrations may differ from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein
are subject to change without notice.
201117_NBF50420