AirWorks.
21487 Ferrero Parkway
City of Industry Ca. 91789
‘Supplement No. AFMS232010006
FAA APPROVED
AIRPLANE FLIGHT MANUAL SUPPLEMENT
TO THE
A319 (-111, -112, -113, -114, -131, -132),
A320 (-144, -214, -212, -214, -231, -232, -233),
and A321 (-114, -112, -131, -211, -231)
FOR THE
AIRWORKS:
COCKPIT DOOR SURVEILLANCE SYSTEM (CDSS)
AIRCRAFT SERIAL No. s AIRCRAFT REG. No.
This supplement must be attached to the basic Airplane Flight Manual, when the aircraft is
modified by the installation of AirWorks Cockpit Door Surveillance System (CDSS) in
accordance with STC No. ST01432LA,
The information contained herein supplements or supersedes the basic Airplane Flight
Manual only in those areas listed herein. For limitations, procedures and performance
information not contained in this supplement, consult the basic Airplane Flight Manual.
Dy fh O
FAA Approved es Toru
Manager, Flight Test Branch, ANI-160L
Federal Aviation Administration
Los Angeles Aircraft Certification Office
Transport Airplane Directorate
Rev A. Approval Date > Omg, AO
Original Approval Date:
February 05, 2003Airworks
J
00.01.00 Pot
Alrous A319, A320, A321
Cockpit Door Surveillance System LOG OF REVISIONS
AIRPLANE FLIGHT MANUAL
SUPPLEMENT
Revision Page
Number No. Date Description FAA Approved
ORIGINAL ALL 02/08/03 Complete ne
Supplement gr, Fk Test Branch, ANMEIGOL
Federal Aviation Administration
Los Angeles Aircraft Cert. Office
FAA, Transport Airplane Directorate
———Febnaary 05,2003
Date
A ALL 01/20/06 | Revised entire
documentto match | AP ao
original AFM formats, |_'CANSC™ TVW EN
Mgr, Ft Test Branch, AN-T60.
Added new ‘Federal Avfation Administration
configurations for Los Angeles Aircraft Cert. Office
STC amendment. FAA, Transport Aiplane Drectorate
EFFECTIVITY CODE
ALLAirworks
Airbus A319, A320, A321
Cockpit Door Surveillance System
AIRPLANE FLIGHT MANUAL
TABLE OF CONTENTS
01.00.00 P 0%
REV.A
‘SUPPLEMENT JANUARY 20, 2008
SECTION DESCRIPTION
00.01.00 APPROVAL PAGE
1.00.00 TABLE OF CONTENTS
2.00.00 GENERAL INFORMATION
3.00.00 LIMITATIONS,
4.00.00 EMERGENCY PROCEDURES
5.00.00 NORMAL PROCEDURES
6.00.00 PERFORMANCE
EFFECTIVITY CODE
ALLAirworks:
Airbus A319, A320, A321
Cockpit Door Surveillance System
AIRPLANE FLIGHT MANUAL
SUPPLEMENT
GENERAL INFORMATION
02.00.00 P 01
REV.A
JANUARY 20, 2008
This manual is applicable to the aircraft on this list:_
A320(-111, 211
ABQ1(-111, 112, 131, -214, -231)
212, -214, 231, -232, -233)
Original Firmware (blue icons) version and
utilize the optional Cabin Ready function
with the 6.4 inch monitor.
Model - Series | Configuration Description | Effectivity |
i - Code |
| This configuration is applicable for the systems |
A319(-111, -112, -113, 114, -131,-132) | equipped with the Ainworks CDSS Upgraded | 001
A320(-111, -211, -212, -214, -231, -232, -233) | Firmware version (gray icons) and utilize the
A211, -112, 131, -211, 231) Cabin Ready function with the 6.4 inch
7 monitor. -
This configuration is applicable for the
A319(-111, 112, 113, -114, 131, -132) | systems equipped with the Airworks CDSS 002
A320(-111, -211, -212, -214, 231, -252, -233) Upgraded Firmware version (gray icons)
ete aie ae ze and utilize the Cabin Secure function with
{ _ the 6.4 inch monitor. _
| This configuration is applicable for the
aa ais i gyi eee _| Systems equipped withthe Airworks COSS 003 |
ils peo iaeaineeoen | Upgraded Firmware version (gray icons)
ea eee oce) andutlize the Cabin Ready functon with
the 5.0 inch monitor. |
This configuration is applicable for the |
A310(-111, 112, -113, -114, -131, -132) |_| systems equipped with the Ainworks CDSS | (004
The pages are number per chapter and section. To identify the effectivity of a page, the following
information is used:
UPPER PART OF PAGE
_ SECTIONSUS SECTION TITLE __CHAPTERISECTIONIPAGE NUMBER
‘Airworks 1.06.00 P 01
Airbus A318, A220, Ag21 GENERAL
Cockpit Door Surveillance Syste
° nanan TABLE OF CONTENTS
AIRPLANE FLIGHT MANUAL REV. XX
‘SUPPLEMENT OCTOBER XX, 20xx
LOWER PART OF PAGE
ai cove:
EFFECTIVITY CODE
001-004
EFFECTIVITY CODE
ALL
REVISION and DATE OF PAGE{ Airworks :
Airbus A319, A320, A321
| Cockpit Door Surveillance System GENERAL INFORMATION
|
02.00.00 P Ot
AIRPLANE FLIGHT MANUAL REV.A
‘SUPPLEMENT JANUARY 20, 2008
LIMITATIONS,
No change
EFFECTIVITY CODE
| au
LSAirbus A318, A320, A321
Cockpit Door Surveillance System
AIRPLANE FLIGHT MANUAL |
SUPPLEMENT |
| Airworks
|
EMERGENCY PROCEDURES
No change.
EFFECTIVITY CODE
EMERGENCY PROCEDURES
4.00.00 P Ot
REV.A
JANUARY 20, 2006Airworks
| 5.00.00 P 01
| Airbus A318, A320, A321 NORMAL PROCEDURES |
| cockpit Door Surveillance Systom
AIRPLANE FLIGHT MANUAL TABLE OF CONTENTS REV.A
‘SUPPLEMENT JANUARY 20, 2006
TABLE OF CONTENTS POL
INTRODUCTION P02
GENERAL P03
SYSTEM PRE-FLIGHT CHECKS...
CDSS SYSTEM OPERATION
TURNING ON THE MONITOR
SELECTING A CAMERA ....
BRIGHTNESS CONTROL DIRECT ACCESS ....
POWER SAVING MODE .... POS
TURNING THE MONITOR OFF MANUALLY... e P06
CAMERAS AND SWITCHER, P07
LOPA (LOCATION OF PRESENT ARRANGEMENT)... P08
PICTURE CONTROL ... P08
PICTURE CONTROL FUNCTION... P09
FLIGHT CREW/CABIN CREW INTERACTION .. P10
evees POF
so POF
Pos
P05
POS
EFFECTIVITY CODE
01 |Airworks
coe NOM ABS, A820, A NORMAL PROCEDURES $0000 0%
“ockpit Door Surveillance Systom s
rene prema ae | REVA
‘SUPPLEMENT JANUARY 20, 2006
TABLE OF CONTENTS .. oe P OL
INTRODUCTION P02
GENERAL i Po3
SYSTEM PRE-FLIGHT CHECKS.. P04
CDSS SYSTEM OPERATION «1... P04
TURNING ON THE MONITOR...
SELECTING A CAMERA .
BRIGHTNESS CONTROL DIRECT ACCESS .
POWER SAVING MODE .. P05
TURNING THE MONITOR OFF MANUALLY. seesee P06
CAMERAS AND SWITCHER... : P07
LOPA (LOCATION OF PRESENT ARRANGEMENT)... P08
PICTURE CONTROL .... P08
PICTURE CONTROL FUNCTION..... P09
FLIGHT CREW/CABIN CREW INTERACTION...... P10
P05
P05
P05
EFFECTIVITY CODE
oC
LoAirworks 5.00.00 P 01
Airbus A318, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System fo 7
AIRPLANE FLIGHT MANUAL Acre OF CONTENTS REV.A
‘SUPPLEMENT JANUARY 20, 2006
TABLE OF CONTENTS... POL
INTRODUCTION
GENERAL *
SYSTEM PRE-FLIGHT CHECKS.....
CDSS SYSTEM OPERATION .
TURNING ON THE MONITOR.
SELECTING A CAMERA
BRIGHTNESS CONTROL DIRECT ACCESS .
POWER SAVING MODE so P OS,
TURNING THE MONITOR OFF MANUALLY... eeeesseeee sessee P06
CAMERAS AND SWITCHER....cssseststsens csvsnntnnnens P07
LOPA (LOCATION OF PRESENT ARRANGEMENT)... P08
PICTURE CONTROL ...+sesesssee oe P08
PICTURE CONTROL FUNCTION ...ssssee Po9
FLIGHT CREW/CABIN CREW INTERACTION .....cscssseen P10
P02
P03
P04
P04
P05
P05
POS
(EFFECTIVITY CODE
003Airworks
5 00.00 P 01
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System _
| AIRPLANE FLIGHT MANUAL TABLE OF CONTENTS | REV.A
SUPPLEMENT | JANUARY 20, 2006
i
TABLE OF CONTENTS
INTRODUCTION ..
GENERAL
SYSTEM PRE-FLIGHT CHECKS..
CDSS SYSTEM OPERATION .....
TURNING ON THE MONITOR...
SELECTING A CAMERA
BRIGHTNESS CONTROL DIRECT ACCESS .
POWER SAVING MODE ...ssssesssoe
TURNING THE MONITOR OFF MANUALLY.
CAMERAS AND SWITCHER.
LOPA (LOCATION OF PRESENT ARRANGEMENT)...
PICTURE CONTROL ..
PICTURE CONTROL FUNCTION......
FLIGHT CREW/CABIN CREW INTERACTION ..
ee POL
P02
P03
P04
P04
P05
P05
P05
POS
P06
Po7
P08
Pos
P09
P10
EFFECTIVITY CODE
aAirworks = 5.0000P 02
Airbus A319, A320, A324 NORMAL PROCEDURES
Cockpit Door Surveillance System _
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT JANUARY 20, 2006
INTRODUCTION
‘The CDSS allows the pilot and copilot to view video images of the area outside the cockpit door
through two video monitors mounted forward of the control sticks of the flight crew. Power to the
CDSS is controlled from an On-Off pushbutton switch labeled CDSS" located on the Overhead
Panel. When selecting the system off, the top half of the switch illuminates “OFF” in white. When.
selecting the system on, the “OFF” light extinguishes, and the switch is not illuminated. If a
system fault exists, “FAULT” illuminates in amber on the bottom half of the switch. Viewing
camera selection is performed by touching the monitor screen to activate a selection menu and
then touching the screen icon corresponding to the desired camera, Monitor screen display is
turned on by touching the screen where there is no icon. An automatic feature exists where a
time, in seconds, can be input and the camera view will automatically shift between cameras.
Monitor brightness control is affected by repeatedly touching the desired brightness control icon on
the screen.
Additionally, there is a optional Cabin Ready which allows the cabin crew to indicate to the cockpit
that the cabin has been prepared for takeoff or landing. The “Cabin Ready” switch, located
adjacent to the cabin attendant panel at door 1L, illuminates green when pressed, This sends a
signal to the Pilots CDSS Monitors, which then annunciate “CABIN READY. Touching either monitor
cancels the annunciation on the monitors and extinguishes the Cabin Ready switch in the cabin,
EFFECTIVITY CODE
001Airworks 5.00.00 P 02
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System -
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT JANUARY 20, 2006
INTRODUCTION
The CDSS allows the pilot and copilot to view video images of the area outside the cockpit door
through two video monitors mounted forward of the control sticks of the flight crew. Power to the
CDSS is controlled from an On-Off pushbutton switch labeled “CDSS” located on the Overhead
Panel. When selecting the system off, the top half of the switch illuminates "OFF" in white, When
selecting the system on, the “OFF” light extinguishes, and the switch is not illuminated. If a
system fault exists, "FAULT" illuminates in amber on the bottom half of the switch. Viewing
camera selection is performed by touching the monitor screen to activate a selection menu and
then touching the screen icon corresponding to the desired camera. Monitor screen display is
turned on by touching the screen where there is no icon, An automatic feature exists where a
time, in seconds, can be input and the camera view will automatically shift between cameras.
Monitor brightness control is affected by repeatedly touching the desired brightness control icon on
the screen.
‘Additionally, there is a optional Cabin Secure feature which allows the cabin crew to indicate to the
cockpit that the cabin has been prepared for takeoff or landing. The “Cabin Secure” switch, located
adjacent to the cabin attendant panel at door LL, illuminates green when pressed. This sends a
signal to the Pilots CDSS Monitors, which then annunciate “CABIN SECURE”. Touching either
monitor cancels the annunciation on the monitors and extinguishes the Cabin Secure switch in the
cabin,
EFFECTIVITY CODE
oy
002 |
=‘Airworks a 0
5.00.00 P 02
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System |__
AIRPLANE FLIGHT MANUAL | REV.A
‘SUPPLEMENT JANUARY 20, 2006
7 - - J
INTRODUCTION
The CDSS allows the pilot and copilot to view video images of the area outside the cockpit door
through two video monitors mounted forward of the control sticks of the flight crew. Power to the
CDSS is controlled from an On-Off pushbutton switch labeled “CDSS” located on the Overhead
Panel. When selecting the system off, the top half of the switch illuminates “OFF” in white. When
selecting the system on, the “OFF” light extinguishes, and the switch is not illuminated. If a
system fault exists, "FAULT" illuminates in amber on the bottom half of the switch. Viewing
camera selection is performed by touching the monitor screen to activate a selection menu and
then touching the screen icon corresponding to the desired camera. Monitor screen display is
turned on by touching the screen where there is no icon. An automatic feature exists where a
time, in seconds, can be input and the camera view will automatically shift between cameras,
Monitor brightness control is affected by repeatedly touching the desired brightness control icon on
the screen.
‘Additionally, there is a Cabin Ready feature which allows the cabin crew to indicate to the cockpit
that the cabin has been prepared for takeoff or landing. The “Cabin Ready” switch, located
adjacent to the cabin attendant panel at door 1L, illuminates green when pressed. This sends a
signal to the Pilots CDSS Monitors, which then annunciate “CABIN READY". Touching either
monitor cancels the annunciation on the monitors and extinguishes the Cabin Ready switch in the
cabin
EFFECTIVITY CODE
003Airworks 5.00.00 P 02
Airbus A318, A320, A321 NORMAL PROCEDURES |
Cockpit Door Surveillance System po
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT | JANUARY 20, 2006
INTRODUCTION
‘The CDSS allows the pilot and copilot to view video images of the area outside the cockpit door
through two video monitors mounted forward of the control sticks of the flight crew. Power to the
CDSS is controlled from an On-Off pushbutton switch labeled “CDSS” located on the Overhead
Panel. When selecting the system off, the top half of the switch illuminates “OFF” in white, When
selecting the system on, the “OFF” light extinguishes, and the switch is not illuminated. If a
system fault exists, “FAULT” illuminates in amber on the bottom half of the switch. Viewing
camera selection is performed by touching the monitor screen to activate a selection menu and
then touching the screen icon corresponding to the desired camera, Monitor screen display is
turned on by touching the screen where there is no icon. An automatic feature exists where a
time, in seconds, can be input and the camera view will automatically shift between cameras.
Monitor brightness control is affected by repeatedly touching the desired brightness control icon on
the screen,
‘Additionally, there is an optional Cabin Ready feature which allows the cabin crew to indicate to the
cockpit that the cabin has been prepared for takeoff or landing. The “Cabin Ready” switch, if
equipped, is located adjacent to the cabin attendant panel at door 1L, illuminates green when
pressed. This sends a signal to the Pilots CDSS Monitors, which then annunciates “CABIN READY”.
Touching either monitor cancels the annunciation on the monitors and extinguishes the Cabin
Ready switch in the cabin,
(EFFECTIVITY CODE
004Airworks: 5.00.00 P 03
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System ~
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT JANUARY 20, 2006
GENERAL
The CDSS installed on the A319 (-111, -112, -113, -114, -131, -132) A320 (-111, -211, -212, -
214, -231, -232, -233) A321 (-111, -112, -131, -211, -231) airplanes consist of:
(A) Two monitors in the cockpit
8) Three viewing cameras with integral light emitting diodes for viewing in darkness.
(C) One system power On-Off switch in the overhead panel,
(
(
(D) One System Control Unit located in flight compartment right ceiling panel above the R1 door.
(E) One 4 Amp circuit breaker labeled "CDSS" located on the 122VU circuit breaker panel,
(
F) For configurations 001-003 and 004 (if equipped), One “Cabin Ready” or “Cabin Secure” switch
located adjacent to the cabin attendant panel at door 1L.
EFFECTIVITY CODE
ALLAirworks 5.00.00 P 04
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Survelance System —___ —
AIRPLANE FLIGHT MANUAL REV.A |
‘SUPPLEMENT | | JANUARY 20, 2006
SYSTEM PRE-FLIGHT CHECKS
NONE REQUIRED
CDSS SYSTEM OPERATION
To turn on power to the CDSS, press and release the “CDSS” switch illuminated “OFF” in white
on the overhead panel. ON (switch dark), (see Figure -1 below).
To turn off the CDSS, press and release the "CDSS" switch on the overhead panel, OFF (white
illumination) will be displayed.
If a fault condition exists, the switch will illuminate "FAULT" (amber illumination).
CDSS On.o#t Switch
CDSS Montor CDSS Monitor
LARS
FIGURE 1 — CDSS PILOT INTERFACES, GENERIC CREW STATION
EFFECTIVITY CODE
AL |‘SUPPLEMENT
‘Airworks | . 5.00.00 P
[ Airbus A319, A320, A321 NORMAL PROCEDURES - |
Cockpit Door Surveillance System | —|
REV. A
|
JANUARY 20, 2006
| AIRPLANE FLIGHT MANUAL
TURNING ON THE MONITOR:
To turn on power to the CDSS, press and release the “CDSS” switch and touch the screen
‘once, in any area, The monitor will turn on, and the following menu will show on the screen:
As default, camera 1 (COC) will be selected until another camera is selected, or until the
automatic mode switches to another camera
NOTE: Other customer options for the labeling of the icons are available, such as CD, Il, and
4R. These would indicate the camera view locations of the Cockpit Door, 1 Left door
and 1 Right door, respectively.
SELECTING A CAMERA
To select a camera view, touch the screen over the icon showing the camera view position
that is the number of the camera that you would like to see.
Bmw B a A
NOTE: For auto-switching, please refer to item 6 below.
BRIGHTNESS CONTROL DIRECT ACCESS:
To change the brightness of the picture, press the PLUS “+” or MINUS *- icon, until the
picture brightness level you desire is achieved.
Ben a
POWER SAVING MODE:
The Power Saving Mode is a factory default setting that will turn off the monitor backlight
when there is no activity for a pre-set amount of time. This helps increase MTBF, as well as
extends the lifetime of the monitor backlight. The Power Saving Mode is automatically
disabled if, in case of an emergency, the common schematic display is displayed, or can be
manually disabled when the screen is touched,
EFFECTIVITY CODE
| oot
|Cockpit Door Surveillance System
Airworks | 5.00.00 P 06.
Airbus A319, A320, A321 NORMAL PROCEDURES
|
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT JANUARY 20, 2006
TURNING THE MONITOR OFF MANUALLY
The monitor can be turned off by touching the monitor screen.
CAMERAS AND SWITCHER
There are two modes in which system switcher can work: AUTOMATIC and MANUAL.
Selecting the switcher mode:
Be Be
Touch the MENU icon,
The On Screen Display Menu will change as shown below.
ee
Touch the SWITCHER icon. The On Screen Display Menu will change as shown below:
From the menus shown above, you can choose "AUTO" or “MANUAL”
Selecting auto mode:
04 & ae — i
Select how long, in seconds, you want each camera to remain on the screen by using the "+"
plus or “-" minus buttons. The example below shows that each camera will remain in the
screen for four seconds.
NOTE: Selecting values less than 5 seconds may cause the screen to flicker during camera view
switching.
EFFECTIVITY CODE| Airworks ] | 5.00.00 P 07
Airbus A319, A320, A321 | NORMAL PROCEDURES |
Cockpit Door Surveillance System paeeaueeneee
REV. A
JANUARY 20, 2006
AIRPLANE FLIGHT MANUAL
SUPPLEMENT
Now, touch the “AUTO” icon,
es
The following menu will show on the screen:
‘The number 1L indicates the camera view being shown, and will change as other cameras are
AUTO selected. To exit the AUTO mode, touch the MENU icon to return to switcher/picture
menu. The following On Screen Display will appear.
Touch the SWITCHER icon and select the MANUAL icon.
ce
The following menu will show on the screen:
an EEE
Touch the number for the camera you want to see.
Selecting manual:
NOTE: This is the default menu that will always be displayed after initial power has been
applied to the system.
EFFECTIVITY CODEAirworks a
Airbus A319, AS20, A324
5.00.00 P 08
| NORMAL PROCEDURES
Cockpit Door Surveillance System
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT
JANUARY 20, 2006
LOPA (Location of present arrangement)
By touching the icon labeled "LOPA" (see Figure 3), the following On Screen Display will
appear over the current camera view being displayed.
Figure 3 - CDSS System LOPA Display
Touch icon COC to view that camera view immediately, as well for icon 1L and 1RTo return to
the main menu and make the LOPA display disappear, press the icon labeled “BACK”.
PICTURE CONTROL
Touch the MENU icon.
BEG BE
Touch the "PICTURE" icon. é
F
The On Screen Display menu will change to the menu shown below:
5
EFFECTIVITY CODE
aaaAirworks 5,00,00 P 0g
]
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System po
AIRPLANE FLIGHT MANUAL. | REV.A
| SUPPLEMENT | JANUARY 20, 2006
You can choose individual calibration for each camera by touching any particular number, or,
you can choose to adjust all cameras by touching the “ALL” icon, After the desired camera (or
ALL”) is touched, the following menu will appear:
A
iH
T
Select the function to be adjusted by touching its icon, then press the plus “+” or minus *=""
icon repeatedly until the desired level of that function is reached. Press “SET” to keep the
changes to the setting you have made. Press “RESET” to reset the setting to the factory default
settings.
Picture Control Function
Below is a description of functions for picture control.
= default factory settings
= Brightness
Level indicator Bar
EFFECTIVITY CODE
001Airworks
Airbus A318, A320, A321
Cockpit Door Surveillance System
AIRPLANE FLIGHT MANUAL
SUPPLEMENT
NORMAL PROCEDURES
Flight Crew/Cabin Crew Interaction. (Cabin Ready)
5.00.00 P 10
REV.A
JANUARY 20, 2006
‘A flight attendant can press the “CABIN READY” switch to let the pilot know that the cabin and
the passengers are ready for take-off or landing. When pressed, the Cabin Ready switch
illuminates in green “CABIN READY” and sends a signal to the CDSS monitor(s), which will then
display in bold green letters “CABIN READY” on the LCD screen(s). The Pilot or Co-Pilot
acknowledges the signal by touching the LCD screen, Touching a monitor screen cancels the
annunciation on the monitor(s) and extinguishes the illuminated Cabin Ready switch at the
Flight Attendant Compartment,
Forward Attendants Station
Flight Attendants check cabin and advise flight
crew when completed.
"| CABIN READY’ switch illuminates when pressed
by the cabin crew to advise the flight crew that
the cabin is ready.
| Notes: CABIN READY
1- On dual monitor installations - the monitor
| messages must be co-ordinated (le, they must
always have the same message / icon displayed
on each monitor).
|| 2- Either monitor can cancel the annunciation on
| the monitor in response to a fight crew input.
EFFECTIVITY CODE
|
001
=
Anywhere on
CockpitAirworks
| | 5
| Airbus A319, A320, A321 NORMAL PROCEDURES £00.00 Po
Cockpit Door Surveillance System = -
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT JANUARY 20, 2006
TURNING ON THE MONITO!
To turn on power to the CDSS, press and release the “CDSS” switch and touch the screen
once, in any area. The monitor will turn on, and the following menu will show on the screen:
‘As default, camera 1 (COC) will be selected until another camera is selected, or until the
automatic mode switches to another camera.
NOTE: Other customer options for the labeling of the icons are available, such as CD, It, and
JR. These would indicate the camera view locations of the Cockpit Door, 1 Left door
and 1 Right door, respectively.
SELECTING A CAMERA
To select a camera view, touch the screen over the icon showing the camera view position
that is the number of the camera that you would like to see.
4
NOTE: For auto-switching, please refer to item 6 below.
BRIGHTNESS CONTROL DIRECT ACCESS:
To change the brightness of the picture, press the PLUS “+” or MINUS -" icon, until the
picture brightness level you desire is achieved.
EES PRE
POWER SAVING MODE:
The Power Saving Mode is a factory default setting that will turn off the monitor backlight
when there is no activity for a pre-set amount of time. This helps increase MTBF, as well as
extends the lifetime of the monitor backlight. The Power Saving Mode is automatically
disabled if, in case of an emergency, the common schematic display is displayed, or can be
manually disabled when the screen is touched
EFFECTIVITY CODE
002Airworks od
Airbus A319, A320, A321 NORMAL PROCEDURES 5.00.00 P
Cockpit Door Surveillance System |
AIRPLANE FLIGHT MANUAL
SUPPLEMENT
-
|
REV.A
JANUARY 20, 2006
TURNING THE MONITOR OFF MANUALLY
‘The monitor can be turned off by touching the monitor screen.
CAMERAS AND SWITCHER
‘There are two modes in which system switcher can work: AUTOMATIC and MANUAL.
Selecting the switcher mode:
[coc] eB — | mi
Touch the MENU icon.
The On Screen Display Menu will change as shown below.
Ea ad A
Touch the SWITCHER icon. The On Screen Display Menu will change as shown below:
From the menus shown above, you can choose “AUTO” or “MANUAL”
Selecting auto mode:
5 a
Select how long, in seconds, you want each camera to remain on the screen by using the *-+"”
plus or "=" minus buttons. The example below shows that each camera will remain in the
screen for four seconds.
NOTE: Selecting values less than 5 seconds may cause the screen to flicker during camera view
switching.
EFFECTIVITY CODEf Airworks §.00.00 P 07
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System {
AIRPLANE FLIGHT MANUAL | REV.A
‘SUPPLEMENT
Now, touch the “AUTO” icon,
The following menu will show on the screen:
Ei
The number 1L indicates the camera view being shown, and will change as other cameras are
AUTO selected. To exit the AUTO mode, touch the MENU icon to return to switcher/picture
menu. The following On Screen Display will appear.
ry
i
=
Touch the SWITCHER icon and select the MANUAL icon.
me
The following menu will show on the screen:
lan EEE ii
Touch the number for the camera you want to see.
| JANUARY 20, 2006
Selecting manual:
NOTE: This is the default menu that will always be displayed after initial power has been
applied to the system.
‘EFFECTIVITY CODE
002i Airworks 6.00.00 P 08
| Airbus A319, A320, A321 NORMAL PROCEDURES
| Cockpit Door Surveillance System —__|
AIRPLANE FLIGHT MANUAL REV.A
| ‘SUPPLEMENT JANUARY 20, 2006
LOPA (Location of present arrangement)
By touching the icon labeled “LOPA" (see Figure 3), the following On Screen Display will
appear over the current camera view being displayed
Figure 3 - CDSS System LOPA Display
Touch icon COC to view that camera view immediately, as well for icon 1L and 1RTo return to
the main menu and make the LOPA display disappear, press the icon labeled “BACK”.
PICTURE CONTROL
Touch the MENU icon.
Touch the "PICTURE" icon
i
‘The On Screen Display menu will change to the menu shown below:
Fy
a
a
A
4
EFFECTIVITY CODE
002| Airworks 5.00.00 P 09
JANUARY 20, 2008
Airbus A319, A320, A321 | NORMAL PROCEDURES
Cockpit Door Surveillance System i
AIRPLANE FLIGHT MANUAL REV.A
SUPPLEMENT |
You can choose individual calibration for each camera by touching any particular number, or,
you can choose to adjust all cameras by touching the “ALL” icon. After the desired camera (or
“ALL”) is touched, the following menu will appear:
ioe
Select the function to be adjusted by touching Its icon, then press the plus “+” or minus "~”
icon repeatedly until the desired level of that function is reached. Press “SET” to keep the
changes to the setting you have made. Press “RESET” to reset the setting to the factory default
settings.
Picture Control Function
Below is a description of functions for picture control,
= Brightness
fm Level indicator Bar
EFFECTIVITY CODEAirworks |
Airbus A318, A320, A321 NORMAL PROCEDURES 500.00 10
Cockpit Door Surveillance System _
REV.A
SUPPLEMENT
| AIRPLANE FLIGHT MANUAL
| JANUARY 20, 2008
Flight Crew/Cabin Crew Interaction,
‘SECURE CABIN REQUIRED
Cockpit
Forward Attendants Station on
FASTEN
Flight Attendants check cabin and advise flight Flight Crew SEAT
‘crew when completed. BELTS
OFF
“CABIN SECURE” switch lluminates when pressed
by the cabin crew to advise the flight crew that
~
Anyeshere on
‘reen
RELEASE CABIN
1 - On dual monitor installations - the monitor
messages must be co-ordinated (ie. they must
|) always have the same message / icon displayed on
5 each monitor).
Cockpit
| 2 Either monitor can action the message / icon
| change in response to a flight crew input /
selection.
3 = The adjustment of the monitor image and
| selection of camera views is independent to the
operation of the CABIN SECURE functionality.
| 4- FASTEN SEAT BELTS is an aircraft function
only and the discrete is not received by the CDSS.
Flight Crew
=
I
002Airworks 5.00.00 P 11
SUPPLEMENT
JANUARY 20, 2006
| Airbus A319, A320, A321 NORMAL PROCEDURES |
Cockpit Boor Surveillance System | -
AIRPLANE FLIGHT MANUAL | REV.A
|
Net effect is to toggle between and
Screens and Legends
“CABIN SECURE” “CABIN SECURE” “CABIN NOT SECURE”
EFFECTIVITY CODE
025.00.00 P 05
Airworks |
Airbus A319, A320, A321 NORMAL PROCEDURES
Cockpit Door Surveillance System (oo
AIRPLANE FLIGHT MANUAL REV.A |
‘SUPPLEMENT JANUARY 20, 2006
TURNING ON THE MONITOR:
To turn on power to the CDSS, press and release the “CDSS” switch and touch the screen
once, in any area, The monitor will turn on, and the following menu will show on the screen:
As default, camera 1 (COC) will be selected until another camera is selected, or until the
automatic mode switches to another camera.
NOTE: Other customer options for the labeling of the icons are available, such as CD, It, and
1R. These would indicate the camera view locations of the Cockpit Door, 1 Left door
and 1 Right door, respectively.
SELECTING A CAMERA
To select a camera view, touch the screen over the icon showing the camera view position
that is the number of the camera that you would like to see.
a Ga Eo EIf&a
BRIGHTNESS CONTROL DIRECT ACCESS:
To change the brightness of the picture, press the PLUS “+” or MINUS "-" icon, until the
picture brightness level you desire is achieved.
Ea Ea If Eso
POWER SAVING MODE: a
‘The Power Saving Mode is a factory default setting that will turn off the monitor backlight
When there is no activity for a pre-set amount of time. This helps increase MTBF, as well as
extends the lifetime of the monitor backlight. The Power Saving Mode is automatically
disabled if, in case of an emergency, the common schematic display is displayed, or can be
manually disabled when the screen is touched.
EFFECTIVITY CODE
]
003 |Cockpit Door Surveillance System
irworks
Airbus A319, A320, A321 NORMAL PROCEDURES
5.00.00 P 06
AIRPLANE FLIGHT MANUAL, REVA
SUPPLEMENT JANUARY 20, 2006
TURNING THE MONITOR OFF MANUALLY
‘The monitor can be turned off by touching the monitor screen.
CAMERAS AND SWITCHER
There are two modes in which system switcher can work: AUTOMATIC and MANUAL,
Selecting the switcher mode:
Ee Co Eo Gal ES En
Touch the MENU icon.
‘The On Screen Display Menu will change as shown below.
ISWITCHERBE PICTURE BEBrcx |
4
Touch the SWITCHER icon. The On Screen Display Menu will change as shown below:
ea Ea
From the menus shown above, you can choose “AUTO” or “MANUAL”
Selecting auto mode:
Select how long, in seconds, you want each camera to remain on the screen by using the "+
plus or *-" minus buttons. The example below shows that each camera will remain in the
screen for four seconds.
NOTE: Selecting values less than 5 seconds may cause the screen to flicker during camera
view switching.
EFFECTIVITY CODE
003Airworks 6.00.00 P 07
Airbus A319, A320, A321 | NORMAL PROCEDURES |
Cockpit Door Surveillance System ——— a
AIRPLANE FLIGHT MANUAL REVA
SURE TEEN JANUARY 20, 2006
Now, touch the “AUTO” icon,
TTY Ee
The following menu will show on the screen:
‘The number COC indicates the camera view being shown, and wn change as other cameras are
AUTO selected. To exit the AUTO mode, touch the MENU icon to return to switcher/picture
menu. The following On Screen Display will appear.
Selecting manual:
Touch the SWITCHER icon and select the MANUAL icon.
The following menu will show on the screen:
ES Ea En Sica
Touch the number for the camera you want to see.
NOTE: This is the default menu that will always be displayed after initial power has been
applied to the system.
EFFECTIVITY CODE
003 |Airworks 0 P 08
5.00.0
|
| Airbus A319, A320, A321 NORMAL PROCEDURES
| Cockpit Door Surveillance System se =
| AIRPLANE FLIGHT MANUAL REVA
| ‘SUPPLEMENT JANUARY 20, 2006
LOPA (Location of present arrangement)
By touching the icon labeled “LOPA" (see Figure 3), the following On Screen Display will
appear over the current camera view being displayed,
Figure 3 — CDSS System LOPA Display
Touch icon COC to view that camera view immediately, as well for icon 1L and 1RTo return to
the main menu and make the LOPA display disappear, press the icon labeled "BACK".
PICTURE CONTROL
Touch the MENU icon,
Em Cd En es ee oe
Touch the “PICTURE” icon. The On Screen Display menu will change to the menu shown
below:
Picture
EFFECTIITY CODE
| 008
|i irworks 7 : 5.00.00 P 05 ]
Airbus A318, A920,A921 | NORMAL PROCEDURES
Cockpit Door Surveillance System | _
AIRPLANE FLIGHT MANUAL | REV.A
‘SUPPLEMENT | JANUARY 20, 2006 |
You can choose individual calibration for each camera by touching any particular number, or,
you can choose to adjust all cameras by touching the “ALL” icon, After the desired camera (or
ALL’) is touched, the following menu will appear:
presen me TTR cs |
Select the function to be adjusted by touching its icon, then press the plus “+” or minus *-”
icon repeatedly until the desired level of that function is reached. Press “SET” to keep the
changes to the setting you have made. Press “RESET” to reset the setting to the factory default
settings.
. Picture Control Function
Below is a description of functions for picture control.
SDD DD f ES tes incater
= Default Factory Settings
fie
Ea = Brightness
ra y = Contrast
= Save Changes to Settings
SET
After SET or RESET, it goes back to below:
EFFECTIVITY CODE
| 004Airworks 5.00.00 P 08
Airbus A318, A320, A321 | NORMAL PROCEDURES
Cockpit Door Surveillance System |
| AIRPLANE FLIGHT MANUAL | REVA.
SUPPLEMENT JANUARY 20, 2006
Flight Crew/Cabin Crew Interaction. (Cabin Ready)
A flight attendant can press the “CABIN READY” switch to let the pilot know that the cabin and
the passengers are ready for take-off or landing, When pressed, the Cabin Ready switch
illuminates in green “CABIN READY” and sends a signal to the CDSS monitor(s), which will then
display in bold green letters “CABIN READY” on the LCD screen(s). The Pilot or Co-Pilot
acknowledges the signal by touching the LCD screen. Touching a monitor screen cancels the
annunciation on the monitor(s) and extinguishes the illuminated Cabin Ready switch at the
Flight Attendant Compartment.
Forward Attendants Station Cockpit
Flight Attendants check cabin and advise flight crew
when completed
* switch illuminates when pressed by
the cabin crew to advise the flight crew thatthe eabin
is ready.
‘Notes: CABIN READY
| 1- On dual monitor installations - the monitor
messages must be co-ordinated (ie. they must always
hhave the same message / icon displayed on each
monitor).
the annunciation on the
ht crew input.
™_]
2.» Either monitor ean can
monitor in response (0a fi5.00.00 P 08
Airworks -
Airbus A319, A920, A324 NORMAL PROCEDURES
Cockpit Deor Surveillance System LL :
AIRPLANE FLIGHT MANUAL | REVA
SUPPLEMENT JANUARY 20, 2006
When the CDSS System On-Off switch, located in the P-11 overhead panel, is pushed, the monitor
will automatically turn on. To turn the monitor off, touch the "OFF icon,
When the monitor screen is touched again, the monitor will turn on and the following menu will
appear,
DEBRA BEE
As default, the camera 1 will be displayed. This camera's view will be displayed until another
camera is selected.
Selecting a camera
There are two modes in which the system switcher can work: AUTOMATIC and MANUAL,
Manual Mode
Manual mode is the default mode when the CDSS System is powered up. You can select a
camera to view manually, by touching the 1 2 or 3 icon on the LCD touchscreen. When touched,
the following menu will appear.
a & a
When an icon has been selected, it will turn green. Go to "Picture Control’ for a description of
menu icons.
Touch the icon labeled “1", to display camera number 1. Touch the icon labeled “2° to display
‘camera number 2, and the icon labeled "3" to display camera number 3
Brightness Control Direct Access
~* icons will adjust the settings brightness level of the monitor.
fia a
Touching the plus "+" or minus
Babee
a
EFFECTIVITY CODE
]
003Airworks | 5,00.00 P06
Airbus A319, A320, A321 | NORMAL PROCEDURES
Cockpit Door Surveillance System | —
AIRPLANE FLIGHT MANUAL REV.A
‘SUPPLEMENT VANUARY 20,2006 |
Automatic Switcher Mode
Touch the MENU icon. The On Screen Display Menu will change as shown below.
ao mes
Now touch the SWITCHER icon. The On Screen Display menu will change as shown below. You can
choose “AUTO" or “MANUAL”.
Deno
Selecting AUTO mode:
Select how long (in seconds) you want each camera to remain on the screen, by using the plus “+
or minus *-" icons. The example below shows that each camera will remain on the screen for four
seconds.
The Monitor will display the icon of the camera being viewed. The number 3 indicates the camera
view being shown.
By selecting the “AUTO” icon, the CDsS will cycle thru cameras at the duration selected, until you
exit AUTO mode.
To exit the automatic switcher mode, touch the “MENU icon to return to the switcher/picture
menu. Then, to return to the main menu, press “BACK”
Another way to exit the automatic switcher mode is to initiate the LOPA by touching anywhere on
the monitor screen.
EFFECTIVITY CODE
004