Professional Documents
Culture Documents
5A@250VV 5A@250VV
c Y CAT II Main Screen
ESM-4420 , ESM-7720 , ESM-9920 ESM-9920 Maximum 15mm / 0.59 inch °C °C
PID Temperature Control Units °F °F
- Adaptation of PID Coefficients to the system with Output-1 Output-2 Fuse AO1 AS1
AO2 AS2
( Process Output or ( Alarm Output-1 )
Self-Tune operation (Step Response Tuning) Alarm Output-2 ) Press ASET/OK Button Press
Supply
- Programmable Heating or Cooling Functions for Note-1 Switch
PSET
P
ASET
to save new Process ASET/OK
Control Output set value and return Button.
- Selectable Alarm Functions for Alarm Output 230 VV Temperature Controller the main screen.
ESM series temperature controllers are designed for measuring and Pt-100 50/60 Hz
Output-3 ESM-9920
controlling a process value. They can be used in many applications ( SSR Output )
with their TC and RTD temperature measurement input, multi-function TC + _ 96mm / 3.78 inch
control outputs, selectable alarm functions. 1 2 3 4 5 6 7 8 9 10 11
12 ± 1 mm / 0.47 inch 84 mm / 3.31 inch °C °C
They are mainly used in glass, plastic, petro-chemistry, textile, °F °F
cY
Process Input 20 mA@12V
automotive and machine production industries. Accurate and ESM-7720 PANEL MOUNTING PO PS PO PS
advanced controlling is performed with selectable ON-OFF, P, PI, PD, CAT II AO
AS
AS1 AS1
AO
PID and Self Tune PID functions. 5A@250VV 5A@250VV
SPECIFICATIONS ASET
DISPLAY Note-1: If process output is SSR driver output, pay attention to the (+) clamps to the holes that
PO PS
Process Display : and (-) pins while doing the connection of the device. located top and bottom
AO AS
ESM-4420 : 10.1 mm Red 4 digit LED Display sides of device and
ESM-7720 : 13.2 mm Red 4 digit LED Display DIMENSIONS screw up the fixing PSET ASET
Maximum 5mm / 0.2 inch P
ESM-9920 : 19 mm Red 4 digit LED Display screws until the unit
ESM-4420
Set Value Display : completely immobile
ESM-4420 : 8 mm Green 4 digits LED Display within the panel. Note: User can exit from Set Value section without saving the
ESM-7720 : 9.1 mm Green 4 digits LED Display
ESM-4420 values by pressing P button.
PSET
ESM-9920 : 10.8 mm Green 4 digits LED Display °C If no operation for 120 seconds, device automatically exits from
Set Value section .
48 mm/ 1.89 inch
°F
Leds : PS (Process Set Value), PO (Process Output Status Led) ,
AS1, AS2 (Alarm Set Values), AO1, AO2 (Alarm Output Status Leds) , PO PS
°C , °F Leds AO1
AO2
AS1
AS2
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Temperature Controller
Operating Temperature: 0...50°C
Humidity : 0-90%RH (none condensing) PSET ASET
P
Protection Class : IP65 at front, IP20 at rear
Weight: ESM-4420 : 220 gr. ,
ESM-7720 : 270 gr. Introduction Brochure. ENG ESM-XX20 01 V08 02/13
48 mm/ 1.89 inch
ESM-9920 : 340 gr. 11 ± 1 mm /0.43 inch 84 mm / 3.31 inch
Easy access diagram for Program Parameters : Unit Selection. or can be chosen. (Default: ) Alarm Types Installation
c
: Operation Scale minimum (Low Limit) value. It changes Alarm
Main Screen After 5 sec. Password Screen Output Before beginning installation of this product, please
according to the process input type and scale. (Default: -200)
°C °C °C °C °C read the instruction manual and warnings below
°F °F °F °F °F
: Operation Scale maximum (High Limit) value. It changes ON
PO PS PO PS PO PS PO PS PO PS
Process High carefully.
AO AS AO AS AO AS AO AS AO AS according to the process input type and scale. (Default: 900)
Alarm
PSET
P
PSET
P
ASET ASET
: Process Set value Low Limit. Minimum set value is defined with OFF
To enter Program menu Press ASET/OK Enter Password with Approve this parameter. It changes according to the process input type and Process Value
press button for 5
PSET
P Button to access increment or password with In package ,
decrement buttons. ASET/OK Button. scale. (Default: -200) Alarm
seconds. Password Screen. Output -One piece unit
: Process Set value High Limit. Maximum set value is defined with
-Two pieces mounting clamp
this parameter. It changes according to the process input type and scale. ON
°C °C °C °C
-One piece instruction manual
°F °F °F °F
(Default: 900)
PO PS PO PS PO PS PO PS Process Low
: Display offset for process value. It can be adjusted from -10% OFF A visual inspection of this product for possible damage occured
AO AS AO AS AO AS AO AS
Alarm
ASET ASET ASET ASET
of scale to 10%of scale. It is added to the process display value. Process Value during shipment is recommended before installation. It is your
°C
(Default: 0) Alarm responsibility to ensure that qualified mechanical and electrical
°F °C °C °C °C
Output technicians install this product.
PO PS
°F °F °F °F
: Control Menu Parameters ( + )
AO AS
PO PS PO PS PO PS PO PS
°C
°F The unit is normally supplied without a power switch or a fuse. Use
PO PS
AO AS
°F
°C
°F
PO PS
: If tune parameter is set to , device start to calculate PID Process Value power switch and fuse as required.
AO AS
ASET
PO PS
AO AS
PO PS
ASET
parameters automatically. This parameter is shown if = . Alarm Be sure to use the rated power supply voltage to protect the unit
AO AS
(Default: ) Output
against damage and to prevent failure.
°C
ASET ASET ( - )
°F °C : Proportional band . It can be adjusted from %1 to %100. ON Keep the power off until all of the wiring is completed so that electric
°C °C °F
PO PS °F °F If = , then this parameter can be observed. (Default: 10.0)
AO AS
PO PS PO PS
PO PS
Deviation Low shock and trouble with the unit can be prevented.
ASET AO AS AO AS
AO AS
: Integral Time. It can be adjusted from 0 to 3600 second. Alarm Never attempt to disassemble, modify or repair this unit. Tampering
ASET OFF
ASET ASET If = , then this parameter can be observed. (Default: 100) with the unit may results in malfunction, electric shock or fire.
°C
°F
°C °C °C
: Derivative Time. It can be adjusted from 0.0 to 999.9 second. Process Value Do not use the unit in combustible or explosive gaseous
°F
PO PS
AO AS PO PS
°F °F
If = , then this parameter can be observed. (Default: 25.0) Alarm
atmospheres. During the equipment is putted in hole on the metal
PO PS
PO PS
Output
: Output Control Period. It can be adjusted from 1 to 150 second ( - ) ( + ) panel while mechanical installation some metal burrs can cause
AO AS AO AS AO AS
ASET
AO AS
PO PS
PO PS
°F
Scale ( - ) If = , then this parameter can be Alarm OFF clamp. Do not do the montage of the device with inappropriate
AO AS PO PS
AO AS
ASET
ASET
ASET
AO AS
observed (Default: 0) mounting clamp. Be sure that device will not fall while doing the
ASET
: Sensor Break Output Value. It can be adjusted from %0 to Process Value montage.
°C Alarm
°F
°C
°F
°C
°F %100. (Default: 0.0) Output It is your responsibility if this equipment is used in a manner not
°C ( - ) ( + )
PO PS
AO AS
PO PS PO PS °F : This parameter determines, which output will be Process specified in this instruction manual.
AO AS AO AS
PO PS control output. If rLY is chosen, process output is relay output, if SSr is ON
ASET ASET ASET AO AS
chosen, process output is SSR output. (Default: rLY) Deviation Range
°C
ASET
: Soft Start Set value. Device operates in Soft Start mode, until Alarm
Garanti
°C °C
OFF
°F °F °F
Warranty
PO PS PO PS PO PS the temperature reaches Soft Start set value. (Default: 0)
AO AS
AO AS AO AS
: Soft Start Control Output. This parameter determines soft start Process Value
ASET ASET
ASET Alarm
mode control output percentage. (Default: 0) Output EMKO Elektronik warrants that the equipment delivered is free from
( - )
°C
°F : Soft Start Control time. This parameter determines soft start defects in material and workmanship. This warranty is provided for a
ON
PO PS mode control time. (Default:0) period of two years. The warranty period starts from the delivery date.
AO AS
Deviation Range
ASET : Alarm Menu Parameters High Alarm
: Alarm Hysteresis value. It can be adjusted from %0 ile %50 of
OFF This warranty is in force if duty and responsibilities which are
Note:If user does not do anything for 120 seconds while device is on programming section, determined in warranty document and instruction manual performs
device turns to operation screen. the Scale( - ). (Default: 0) Process Value
: Alarm Type selection. (Default: )
by the customer completely.
Tune Operation : Alarm Set Low Limit parameter. It can be adjusted from Error Messages
Operation Scale minimum to Alarm Set High Limit. (Default: 0) °C Maintenance
Starting the Tune operation °F
: Alarm Set High Limit parameter. It can be adjusted from Alarm
1-Enter to the programming section PO PS 1- Sensor failure in analog inputs. Sensor
2- Select , parameter in menu. Press ASET/OK button for saving the Set Low Limit to Operation Scale maximum. (Default: 500) Repairs should only be performed by trained and specialized
AO AS connection is wrong or there is no sensor
parameter and turn to the main operation screen. : Alarm on Delay Time. It can be adjusted from 0 to 9999 personnel. Cut power to the device before accessing internal parts.
connection.
3- Observe that “ ” blinks in set display. seconds. (Default: 0)
PSET
P
ASET
: R type (Pt13%RhPt) Termocuple , 0°C,1700°C ; 32°F,3092°F does not allow to do any changes without Phone : +90 224 261 1900
: Protection Menu Parameter entering the password correctly. Fax : +90 224 261 1912
: S type (Pt10%RhPt) Termocuple , 0°C,1700°C ; 32°F,3092°F : Password for accessing to the programming section. It can be
: T type (Cu,Cu,Ni) Termocuple , -200°C,400°C ; -328°F,752°F
°C
5- In programming section, when Tune
adjusted from 0 to 9999. °F
If is 0, password screen is not observed. If is different from operation is selected , if warning which is
: Pt - 100 , -200°C,650°C ; -328°F,1202°F PO PS
0 and user enters to the menu pages without entering the password, all AO AS
shown on the left blinks in operation screen for
: Pt - 100 , -199.9°C,650.0°C ; -199.9°F,999.9°F the menus can be observed except protection menu . But device 10 seconds, it means that start conditions is not
does not allow to do any changes in parameters. (Default value is 0) PSET
P
ASET
okay for Tune operation.
Ordering Information
ESM-4420 ( 48x48 DIN 1/16 ) A BC D E / FG HI / U V W Z
ESM-7720 ( 72x72 DIN Size )
ESM-9920 ( 96x96 DIN 1/4 ) 0 / 01 02 / 0 0 0 0
A Supply Voltage
2 24V V50/60Hz or 24VZ( ± %15 )
3 24V V ( ± %15 ) 50/60Hz
4 115V V ( ± %15 ) 50/60Hz
5 230V V ( ± %15 ) 50/60Hz
9 Customer