Professional Documents
Culture Documents
reviewer4@nptel.iitm.ac.in ▼
Unit 5 - Week 3:
Geotechnical Investigations - II
Register for
Certification exam Assignment 3
The due date for submitting this assignment has passed. Due on 2019-03-20, 23:59 IST.
Course As per our records you have not submitted this assignment.
outline
Assignment 3
How to access
1) A SPT test was conducted on a clayey soil at a depth of 6m from the ground surface. 0 points
the portal
The number of blows required for the second and third penetration of 15 cm each were recorded as 15
Prerequisite and 18.
Assessment Considering ground water located at ground level and γ to be 19 kN/m3, find out the corrected SPT-N
value for the location.
Week 1: (Consider correction factor for overburden pressure, CN=0.77*log (2000/ σ’v) , σ’v= effective
Subsurface overburden pressure)
Exploration:
Need and 27
Objectives
34
Week 2: 29
Geotechnical 39
Investigations - I
No, the answer is incorrect.
Week 3: Score: 0
Geotechnical Accepted Answers:
Investigations - II
39
Lecture 1: Cone 2) During the subsurface investigation for the design of a foundation, a SPT test was conducted 1 point
Penetration Test
at 4.5m below ground level. The recorded number of blows are given below:
Lecture 2:
Dilatometer Test Penetration depth (cm): 0-7.5 7.5-15 15-22.5 22.5-30 30-37.5 37.5-45
Lecture 3: No. of Blows 3 3 6 6 8 7
Pressuremeter Assuming water table at ground level, soil as fine sand and correction factor for overburden to be 1.0.
Test The corrected SPT-N value would be:
Quiz :
18
Assignment 3
19
Lecture Note
21
Assignment 3 33
solution
No, the answer is incorrect.
Week 4: Score: 0
Geophysical
Investigation - I Accepted Answers:
21
Week 5: 3) Following are the results from a pressuremeter test, conducted at 4m depth from ground 1 point
Geophysical
Investigation II surface on a clay (NC) deposit. If the probe used was BX type, find out the pressuremeter modulus (Em
).
Pressure (bar) Volume (cc)
https://onlinecourses-archive.nptel.ac.in/noc19_ce10/unit?unit=17&assessment=23 1/4
28/07/2020 Subsurface exploration importance and techniques involved - - Unit 5 - Week 3: Geotechnical Investigations - II
Week 6: Offshore
investigation 0.311226 77.81812
0.754505 124.5423
Week 7: Offshore 1.093993 146.6233
investigations II 1.459999 159.6337
2.140236 170.0923
Week 8: Dynamic 3.108284 184.477
Testing of Piles 4.102365 201.353
5.070317 219.7313
Interaction 6.063913 250.9712
session 6.978587 292.5713
7.969905 384.7368
8.776232 523.5451
50-100 bar
100-200 bar
200-300 bar
300-400 bar
4) Referring to Question 3, the value of Young’s modulus (E) of the soil would be? 1 point
150-250 bar
250-350 bar
350-450 bar
450-550 bar
6) In Dilatometet Tes (DMT) test, number of readings taken at the ground surface is 1 point
1
2
3
4
7) While performing an in-situ DMT, following observations are made. Consider1 point
∆A=-28 kPa, ∆B= 48 kPa, Zm = 5kPa and ground water to be located at ground
surface. Find out the minimum value of material index (ID ) among all the soil layers.
https://onlinecourses-archive.nptel.ac.in/noc19_ce10/unit?unit=17&assessment=23 2/4
28/07/2020 Subsurface exploration importance and techniques involved - - Unit 5 - Week 3: Geotechnical Investigations - II
0.42
0.028
0.26
0.10
8) Referring to Question 7 above, what would be the maximum value of dilatometer modulus 1 point
(ED in bar)
5.46
12.38
19.31
36.07
9) In case of dry soil, Dilatancy correction in SPT value will be; 1 point
Positive
Negative
Zero
More information needed to decide
10)In Pressuremeter test set-up, the pressure in guard cell is…………….in comparison to 1 point
measuring cell.
Less
More
Equal
No pressure at all
Funded by
Powered by
https://onlinecourses-archive.nptel.ac.in/noc19_ce10/unit?unit=17&assessment=23 4/4